High Molecular Weight Polymers Research Articles

Controlled Synthesis of Dendrite-like Polyglycerols Using Aluminum Complex for Biomedical Applications.

This work describes a one-pot synthesis of dendrite-like hyperbranched polyglycerols (HPGs) via a ring-opening multibranching polymerization (ROMBP) process using a bis(5,7-dichloro-2-methyl-8-quinolinolato)methyl aluminum complex (1) as a catalyst and 1,1,1-tris(hydroxymethyl)propane/trimethylol propane (TMP) as an initiator. Single-crystal X-ray diffraction (XRD) analysis was used to elucidate the molecular structure of complex 1. Inverse-gated (IG)13C NMR analysis of HPGs showed degree of branching between 0.50 and 0.57. Gel permeation chromatography (GPC) analysis of the HPG polymers provided low, medium, and high-molecular weight (M n) polymers ranging from 14 to 73 kDa and molecular weight distributions (M w/M n) between 1.16 and 1.35. The obtained HPGs exhibited high wettability with water contact angle between 18 and 21° and T g ranging between -39 and -55 °C. Notably, ancillary ligand-supported aluminum complexes as catalysts for HPG polymerization reactions have not been reported to date. The obtained HPG polymers in the presence of the aluminum complex (1) can be used for various biomedical applications. Here, nanocomposite electrospun fibers were fabricated with synthesized HPG polymer. The nanofibers were subjected to cell culture experiments to evaluate cytocompatibility behavior with L929 and MG63 cells. The cytocompatibility studies of HPG polymer and nanocomposite scaffold showed high cell viability and spreading. The study results concluded, synthesized HPG polymers and composite nanofibers can be used for various biomedical applications.

Low-intensity mixing process of high molecular weight polymer chains leads to elastomers of long network strands and high fatigue threshold.

Many polymer networks are prepared by crosslinking polymer chains. The polymer chains and crosslinkers are commonly mixed in internal mixers or roll mills. These intense processes break the polymer chains, lower viscosity, and ease mixing. The resulting polymer networks have short chains and a fatigue threshold of ∼100 J m-2. Here, we show that a low-intensity process, a combination of kneading and annealing, preserves long chains, leading to a network of polybutadiene to achieve a fatigue threshold of 440 J m-2. In a network, each chain has multiple crosslinks, which divides the chain into multiple strands. At the ends of the chain are two dangling strands that do not bear the load. The larger the number of crosslinks per chain, the lower the fraction of dangling strands. High fatigue threshold requires long strands, as well as a low fraction of dangling strands. Once intense mixing cuts chains short, each short chain can only have a few crosslinks; the strands are short and the fraction of dangling strands is high-both lower the fatigue threshold. By contrast, a low-intensity mixing process preserves long chains, which can have many crosslinks; the strands are long and the fraction of dangling strands is low-both increase the fatigue threshold. It is hoped that this work will aid the development of fatigue-resistant elastomers.

Health promoting benefits of postbiotics produced by lactic acid bacteria: Exopolysaccharide

Exopolysaccharides are high molecular weight polymers of repeated sugar units with diverse chemical structure and unique properties and produced by microorganisms. Lactic acid bacteria are important exopolysaccharide producers. Lactic acid bacteria derived exopolysaccharides, one of the postbiotics, are known to have technological properties such as stabilizing, thickening, emulsifing and also biological activities. Lactic acid bacteria can synthesis exopolysaccharides with large structural variability and this diversity brings these polymers to possess several bioactivities. Bioactivities such as immunomodulatory, antiinflammatory, antitumor and antimutagenicity, antioxidant, antibacterial and antiviral, cholesterol-lowering, antihypertensive activity and gastro-protective activity bring these biopolymers commercial value in the global market and potential to be used in biomedical and pharmaceutical applications. Therefore, to evaluate the availability of these natural exopolysaccharides for new applications extensive understanding of the structure-function relationships will be required. In this review, it is presented a comprehensive overview for the most recent reports on the health benefits of postbiotic lactic acid bacterial exopolysaccharides.

Improvement of enzymatic cross-linking of ovalbumin and ovotransferrin induced by transglutaminase with heat and reducing agent pretreatment

The effects of transglutaminase (TGase, 1.0 unit/mL) with heat (95 °C, 5 min), 2-mercaptoethanol (2-ME, 0.83 %), and l-cysteine (l-Cys, 50 mM) pretreatment on the cross-linking of ovalbumin (OVA) and ovotransferrin (OVT) were investigated. SDS-PAGE revealed that although the polymerization of OVA and OVT did not occur after 3 h of incubation at 40 °C with TGase, OVA polymerized into high molecular weight polymers following TGase with 2-ME and heat pretreatment after 3 h of incubation. The surface hydrophobicity and reactive sulfhydryl (SH) groups of OVA samples significantly increased from 4065.7 ± 136.7 and 89.3 ± 1.2 SH groups (μmol/g) to 31483.6 ± 342.7 and 119.5 ± 3.7 SH groups (μmol/g), respectively. Similar results were obtained for OVT with TGase and l-Cys pretreatment and a 3-h incubation at 40 °C. The use of TGase, a reducing agent, and/or heat pretreatment can be used for the polymerization of OVA and OVT.

Unsymmetrical Strategy on α-Diimine Nickel and Palladium Mediated Ethylene (Co)Polymerizations.

Among various catalyst design strategies used in the α-diimine nickel(II) and palladium(II) catalyst systems, the unsymmetrical strategy is an effective and widely utilized method. In this contribution, unsymmetrical nickel and palladium α-diimine catalysts (Ipty/iPr-Ni and Ipty/iPr-Pd) derived from the dibenzobarrelene backbone were constructed via the combination of pentiptycenyl and diisopropylphenyl substituents, and investigated toward ethylene (co)polymerization. Both of these catalysts were capable of polymerizing ethylene in a broad temperature range of 0-120 °C, in which Ipty/iPr-Ni could maintain activity in the level of 106 g mol-1 h-1 even at 120 °C. The branching densities of polyethylenes generated by both nickel and palladium catalysts could be modulated by the reaction temperature. Compared with symmetrical Ipty-Ni and iPr-Ni, Ipty/iPr-Ni exhibited the highest activity, the highest polymer molecular weight, and the lowest branching density. In addition, Ipty/iPr-Pd could produce copolymers of ethylene and methyl acrylate, with the polar monomer incorporating both on the main chain and the terminal of branches. Remarkably, the ratio of the in-chain and end-chain polar monomer incorporations could be modulated by varying the temperature.

Synergistic Effect of Polysaccharides from Chamomile Tea with Nitazoxanide Increases Treatment Efficacy against Giardia intestinalis.

Giardia intestinalis (syn. G. lamblia, G. duodenalis) is a protozoa parasite that produces one of the most frequent waterborne causes of diarrhea worldwide. This protozoan infects most mammals, including humans, and colonizes the small intestine, adhering to intestinal cells. The mechanism by which G. intestinalis causes diarrhea is multifactorial, causing intestinal malabsorption. The treatment of giardiasis uses chemotherapeutic drugs such as nitroimidazoles, furazolidone, paromomycin, and benzimidazole compounds. However, they are toxic, refractory, and may generate resistance. To increase efficacy, a current treatment strategy is to combine these drugs with other compounds, such as polysaccharides. Several studies have shown that polysaccharides have gastroprotective effects. Polysaccharides are high-molecular weight polymers, and they differ in structure and functions, being widely extracted from vegetables and fruits. In the present study, we show that polysaccharides found in chamomile tea (called MRW), in contact with antiparasitic agents, potentially inhibit the adhesion of parasites to intestinal cells. Moreover, at 500 µg/mL, they act synergistically with nitazoxanide (NTZ), increasing its effectiveness and decreasing the drug dose needed for giardiasis treatment.

Melanins from the Lichens Lobaria pulmonaria and Lobaria retigera as Eco-Friendly Adsorbents of Synthetic Dyes

Synthetic dyes are widely used in the industry; they are chemically stable, difficult to neutralize, and therefore they are a threat to the environment when released into wastewaters. The dyes have a significant impact on plant performance by impairing photosynthesis, inhibiting growth, and entering the food chain and may finally result in the toxicity, mutagenicity and carcinogenicity of food products. Implementation of the dark piment melanin for the adsorption of the synthetic dyes is a new ecologically friendly approach for bioremediation. The aim of the present work was to study the physico-chemical characteristics of melanins from the lichens Lobaria pulmonaria and Lobaria retigera, analyze their adsorption/desorption capacities towards synthetic dyes, and assess the capacity of melanins to mitigate toxicity of the dyes for a common soil bacterium Bacillus subtilis. Unique chelating properties of melanins determine the perspectives of the use of these high molecular weight polymers for detoxification of xenobiotics.

Solid–Liquid Separation of Dairy Barn by Electrocoagulation with Cationic Polymer Coagulant

High–molecular-weight polymer coagulants are widely used in wastewater treatment combined with traditional inorganic coagulants to improve the solid–liquid separation efficiency. However, it is desirable to keep chemicals used in treatments at minimum levels for economic and safety reasons. This study aimed to increase the efficiency of two-stage electro- and chemical-coagulation treatment with a minimum chemical dosage for the separation of solids and liquid in dairy manure slurry for the safe composting of solids and safe discharge of wastewater. Accordingly, dairy manure slurry was treated with aluminum (Al) coagulants, such as polyaluminum chloride (PAC), aluminum chloride (AlCl3), and aluminum sulfate (Al2(SO4)3), PAC combined with the cationic polyacrylamide (CPAM), and PAC and CPAM combined with electrocoagulation (EC). Results revealed that PAC was the best among the Al coagulants evaluated for the reduction in turbidity in the liquid fraction at a dosage of 100 mg/L. PAC dosage was reduced to 40 mg/L when the treatments were combined with CPAM at a dosage of 40 mg/L, which was further reduced to 30 mg/L when treatments were combined with 5 min EC and 20 mg/L of CPAM dosage.

Carbonylative Co- and Terpolymerizations of 10-Undecen-1-ol: A Route to Polyketoesters with Tunable Compositions

A strategy to synthesize branched polyketoesters from the carbonylative polymerization of bifunctional α,ω-alkenols such as 10-undecen-1-ol is presented. This strategy hinges on the competitive application of two related catalytic manifolds, alternating alkene/CO copolymerization, and alkene hydroesterification, which share a common metal acyl intermediate. Small molecule model studies of cationic Pd-catalyzed alkene carbonylation in the presence of alcohols demonstrate that the relative rates of ketone formation (through alternating alkene/CO insertion) and ester formation (through metal acyl alcoholysis) can be tuned across a wide range through judicious bis(phosphine) ligand design. Carbonylative polymerization of 10-undecen-1-ol with a (dppp(3,5-CF3)4)Pd(OTs)2 catalyst (dppp(3,5-CF3)4 = 1,3-bis[bis[3,5-bis(trifluoromethyl)phenyl]-phosphino]propane) led to the formation of high molecular weight polyketoesters with intermediate dispersity (Mn > 20,000 g/mol, D̵ = 2.6) and a ketone/ester microstructure ratio of approximately 1:2. In these polymerization reactions, deploying electron-deficient bis(phosphines) to suppress deleterious alkene isomerization was the key to accessing the high molecular weight polymer. Further, terpolymerization reactions of 1-hexene/10-undecen-1-ol/CO or 1-fluoro-10-undecene/10-undecen-1-ol/CO by (dppp(3,5-CF3)4)Pd(OTs)2 were also successful. This proof of concept polymerization unlocks access to tunable polymer microstructures without extensive postpolymerization treatment.

Controlled Synthesis of High-Molecular-Weight Polystyrene and Its Block Copolymers by Emulsion Organotellurium-Mediated Radical Polymerization.

Structurally controlled high-molecular-weight (HMW) polystyrenes (PSts) and block copolymers consisting of HMW PSt segments were successfully synthesized by emulsion organotellurium-mediated radical polymerization (TERP). The hydrophilicity of the organotellurium group of TERP chain transfer agents (CTAs) was important for success, and CTAs 1b and 1c with di- and tetraethylene glycol units were suitable. By using 1b and 1c and using hexadecyltrimethylammonium bromide (CTAB) as the surfactant, PSts with MWs over 1 million and with low dispersity (Đ < 1.6) were synthesized with >96% monomer conversion. Because of the high monomer conversion, high end-group fidelity, and rapid monomer diffusion to polymer particles, HMW block copolymers with low dispersity were successfully synthesized by adding a second monomer after converting the first monomer without isolating the macroinitiators. Despite recent developments in reversible-deactivation radical polymerization (RDRP), the synthesis of HMW polymers, particularly PSts and block copolymers, has been a formidable challenge. This method provides a valuable route for fabricating polymer materials based on HMW PSts.

Pharmaceutical Assessment of Watermelon Rind Pectin as a Suspending Agent in Oral Liquid Dosage Forms.

Pectin is a high molecular weight polymer which is present in virtually all plants where it contributes to the cell structure. Pectin is a high valuable food ingredient widely used as a gelling agent and thickening agent with limited use in the pharmaceutical industry. The objective of this study is to evaluate the suspending properties of pectin from watermelon rind. Tragacanth was used as a standard suspending agent to which the suspending properties of pectin from watermelon rinds were compared with. The extracted pectin was subjected to phytochemical and physiochemical characterization for its safety and suitability to use as a suspending agent. Paracetamol suspensions were formulated using tragacanth concentrations of 0.5% w/v, 1% w/v, and 2% w/v and compared with paracetamol suspensions containing the same concentrations of watermelon pectin. The suspensions were all tested for their pH, sedimentation rate, sedimentation volume, flow rate, and ease of redispersibility over a period of 4 weeks. At the end of the 4-week period, all formulated suspensions had no changes in their pH values. Suspensions containing the extracted pectin had a lower rate of sedimentation and ease of redispersibility compared to that of tragacanth. In addition, their sedimentation volumes as well as flow rates were comparable to that of the tragacanth formulations. Ultimately, pectin from watermelon rind can serve as a suitable alternative to tragacanth in formulation of pharmaceutical suspensions.

Megadalton Macromolecules Made-to-Order in Minutes: A Highly Active Nanosphere Catalyst for Preparing High-Molecular Weight Polymers

Megadalton Macromolecules Made-to-Order in Minutes: A Highly Active Nanosphere Catalyst for Preparing High-Molecular Weight Polymers

Tuning polycaprolactone degradation for long acting implantables

Polycaprolactone (PCL) is a bioresorbable polyester that has been widely used in biomedical applications since the 1970s. Because PCL undergoes bulk degradation, it is especially amenable to drug delivery applications. To ensure safety, a drug eluting implant must typically remain intact until the drug is exhausted, and following exhaustion the implant should breakdown and be resorbed. Many PCL based implants target delivery on the order of six months to one year, yet the time to degradation of PCLs is often on the order of multiple years. It is known that the time to degradation of PCL is directly related to its initial molecular weight; however, the limited integrity of neat low molecular weight PCLs make them unsuitable for implantation. Here we outline an approach to tune the time to degradation of PCL by blending low and high molecular weight polymers. We show that the degradation rate and permeability of PCL films are insensitive to their composition, and weight-average molecular weight (Mw) is predictive of time to fragmentation. Additionally, we demonstrate that compositions with up to 50 wt % low molecular weight polymer can retain the mechanical properties of a high molecular weight material. The resulting material has a lower effective Mw and a shorter time to degradation. In accelerated testing, it is possible to reduce time to degradation by roughly two-fold without sacrificing mechanical integrity. This provides versatility in adapting device designs to meet the needs of a specific application. These findings have implications in the development of biodegradable drug eluting implants, tissue engineering scaffolds, and resorbable surgical materials.

Composite Membranes Based on Functionalized Mesostructured Cellular Foam Particles and Sulfonated Poly(Ether Ether Sulfone) with Potential Application in Fuel Cells.

Composite polymeric membranes were designed based on sulfonated poly(ether ether sulfone) (sPEES) and mesostructured cellular foam (MCF) silica nanoparticles functionalized with organic compounds. Parameters such as molecular weight (MW) of the polymer, nature of the functional group of the MCF silica, and percentage of silica charge were evaluated on the final properties of the membranes. Composite membrane characterization was carried out on their water retention capacity (high MW polymer between 20-46% and for the low MW between 20-60%), ion exchange capacity (IEC) (high MW polymer between 0.02 mmol/g-0.07 mmol/g and low MW between 0.03-0.09 mmol/g) and proton conductivity (high MW polymer molecular between 15-70 mS/cm and low MW between 0.1-150 mS/cm). Finally, the membrane prepared with the low molecular weight polymer and 3% wt. of functionalized silica with sulfonic groups exhibited results similar to Nafion® 117.

Side‐Chain Control of Topochemical Polymer Single Crystals with Tunable Elastic Modulus

AbstractTopochemical polymerizations hold the promise of producing high molecular weight and stereoregular single crystalline polymers by first aligning monomers before polymerization. However, monomer modifications often alter the crystal packing and result in non‐reactive polymorphs. Here, we report a systematic study on the side chain functionalization of the bis(indandione) derivative system that can be polymerized under visible light. Precisely engineered side chains help organize the monomer crystals in a one‐dimensional fashion to maintain the topochemical reactivity. By optimizing the side chain length and end group of monomers, the elastic modulus of the resulting polymer single crystals can also be greatly enhanced. Lastly, using ultrasonication, insoluble polymer single crystals can be processed into free‐standing and robust polymer thin films. This work provides new insights on the molecular design of topochemical reactions and paves the way for future applications of this fascinating family of materials.

Side-Chain Control of Topochemical Polymer Single Crystals with Tunable Elastic Modulus.

Topochemical polymerizations hold the promise of producing high molecular weight and stereoregular single crystalline polymers by first aligning monomers before polymerization. However, monomer modifications often alter the crystal packing and result in non-reactive polymorphs. Here, we report a systematic study on the side chain functionalization of the bis(indandione) derivative system that can be polymerized under visible light. Precisely engineered side chains help organize the monomer crystals in a one-dimensional fashion to maintain the topochemical reactivity. By optimizing the side chain length and end group of monomers, the elastic modulus of the resulting polymer single crystals can also be greatly enhanced. Lastly, using ultrasonication, insoluble polymer single crystals can be processed into free-standing and robust polymer thin films. This work provides new insights on the molecular design of topochemical reactions and paves the way for future applications of this fascinating family of materials.

Recent Advances in Polymer Flooding in China.

Polymer flooding is drawing lots of attention because of the technical maturity in some reservoirs. The first commercial polymer flooding in China was performed in the Daqing oilfield and is one of the largest applications in the world. Some laboratory tests from Daqing researchers in China showed that the viscoelasticity of high molecular weight polymers plays a significant role in increasing displacement efficiency. Hence, encouraged by the conventional field applications and new findings on the viscoelasticity effect of polymers on residual oil saturation (ROS), some high-concentration high-molecular-weight (HCHMW) polymer-flooding field tests have been conducted. Although some field tests were well-documented, subsequent progress was seldom reported. It was recently reported that HCHMW has a limited application in Daqing, which does not agree with observations from laboratory core flooding and early field tests. However, the cause of this discrepancy is unclear. Thus, a systematic summary of polymer-flooding mechanisms and field tests in China is necessary. This paper explained why HCHMW is not widely used when considering new understandings of polymer-flooding mechanisms. Different opinions on the viscoelasticity effect of polymers on ROS reduction were critically reviewed. Other mechanisms of polymer flooding, such as wettability change and gravity stability effect, were discussed with regard to widely reported laboratory tests, which were explained in terms of the viscoelasticity effects of polymers on ROS. Recent findings from Chinese field tests were also summarized. Salt-resistance polymers (SRPs) with good economic performance using produced water to prepare polymer solutions were very economically and environmentally promising. Notable progress in SRP flooding and new amphiphilic polymer field tests in China were summarized, and lessons learned were given. Formation blockage, represented by high injection pressure and produced productivity ability, was reported in several oil fields due to misunderstanding of polymers’ injectivity. Although the influence of viscoelastic polymers on reservoir conditions is unknown, the injection of very viscous polymers to displace medium-to-high viscosity oils is not recommended. This is especially important for old wells that could cause damage. This paper clarified misleading notions on polymer-flooding implementations based on theory and practices in China.

Process conditions affect properties and outcomes of polyhydroxyalkanoate accumulation in municipal activated sludge

The developments of mixed culture polyhydroxyalkanoate production has been directed to maximize the biomass PHA content with limited attention to polymer quality. Direct comparison of PHA accumulation literature is challenging, and even regularly contradicting in reported results, due to underlying differences that are not well expressed. A study was undertaken to systematically compare the commonly reported process conditions for PHA accumulation by full-scale municipal activated sludge. A biomass acclimation step combined with a pulse-wise feeding strategy resulted in maximum average PHA contents and product yields. pH control and active nitrification did not result in observable effects on the PHA productivity. Under these conditions a high molecular weight polymer (1536 ± 221 kDa) can be produced. Polymer extraction recoveries were influenced by the PHA molecular weight. A standard protocol for an activated sludge PHA accumulation test including downstream processing and standardized extraction has been developed and is available as supplementary material.

Synthesis, Characterization and UV‐Crosslinking of Aromatic (Co)polycarbonates Bearing Pendant Azido Groups

AbstractA new series of (co)polycarbonates bearing pendent azido groups was synthesized by polycondensation of varying molar proportions of 4, 4’‐(5‐azidopentane‐2, 2‐diyl) diphenol and bisphenol‐A with triphosgene. The chemical structures, compositions and random nature of (co)polycarbonates were confirmed by NMR spectroscopy. Inherent viscosities and number‐average molecular weights of (co)polycarbonates were in the range 0.63–0.77 dL g−1 and 35,400–43,400 g mol−1, respectively indicating the formation of reasonably high molecular weight polymers. (Co)polycarbonates could be cast into tough, transparent and flexible films from chloroform solutions. (Co)polycarbonates were further characterized using IR spectroscopy, XRD, TGA and DSC. The thermal crosslinking of (co)polycarbonates bearing pendant azido groups was studied by DSC analysis. Independently, (co)polycarbonates bearing pendant azido groups were exposed to UV irradiation at wavelength of 254 nm and decomposition reaction of azido groups was monitored by FT‐IR spectroscopy. The complete decomposition of azido groups was observed with exposure time of 30 min. The formed cross‐linked (co)polycarbonates exhibited improved % char yield values compared to parent (co)polycarbonates. The measurement of mechanical properties of representative crosslinked (co)polycarbonates indicated increase in tensile strength and Young's modulus and decrease in % elongation compared to corresponding parent linear (co)polycarbonates.

Synthesis, characterization and post-modification of aromatic (Co)polyesters possessing pendant maleimide groups

A new series of (co)polyesters possessing pendent maleimide groups was synthesized by low temperature solution polycondensation of 4, 4’-(5-maleimidopentane-2, 2-diyl) diphenol (BPA-MA) with isophthalic acid chloride (IPC), terephthalic acid chloride (TPC) and a mixture of TPC and IPC (50:50 mol %). Copolyesters were also synthesized by polycondensation of varying compositions of BPA-MA and bisphenol-A (BPA) with IPC. The chemical structures and compositions of (co)polyesters were confirmed by NMR spectroscopy. Inherent viscosity values and number-average molecular weights of (co)polyesters were in the range 0.50–0.76 dL/g and 17,700-32,100 g/mol, respectively, indicating the formation of reasonably high molecular weight polymers. (Co)polyesters were readily soluble in common organic solvents and could be cast into tough, transparent and flexible films from chloroform solutions. (Co)polyesters exhibited 10% weight loss and glass transition temperatures in the range 464–468 and 142–178°C, respectively. A representative copolyester possessing pendant maleimide groups was chemically modified via metal-free azide-maleimide 1,3-dipolar cycloaddition click reaction with two azido compounds, namely, (azidomethyl)benzene (Bz-N3) and 1-(azidomethyl)-pyrene (Py-N3) to yield corresponding modified copolyesters in a quantitative manner.