High Concentrations Of Manganese Research Articles

BENTHIC MACROINVERTEBRATE COMMUNITY IN TWO AMAZONIAN UPLAND LAKES

Studies of biological communities in Amazonian lakes are limited to floodplains of large rivers. However, the high-altitude lakes of the Serra dos Carajás differ from other lakes in the region due to the high natural concentration of iron and manganese. An important component of this biological community are the macroinvertebrates, some of which are sensitive to environmental and chemical variables. However, little is known about the influence of heavy metal concentrations on this community component in Amazonian lakes. In our study, we observed the importance of variables such as water depth and concentration of chemical elements in sediments on the macroinvertebrate community. Through a redundancy analysis, we found that the depth of the lake affects the number of species and the composition of the benthic macroinvertebrate community. We also found a relative importance of the concentration of manganese in the sediment for the community studied. Our results indicate that the macroinvertebrate community is differentiated in the marginal and central regions of the lake, since the deposition of organic matter and heavy metals in the sediment is different in these two regions of the lake. The relationship found has implications for the management and restoration of upland lakes in the Amazon, helping to preserve this unique ecosystem.

Water Quality Monitoring in the Volga Headwaters

The Volga River is the largest river in Europe in terms of basin area (1.36 mio. km2), length (3531 km), and water content (annual flow 254 km3). We conduct long-term water quality studies in the Volga headwaters: in the Upper Volga Lakes, the free-flowing section, as well as in the Ivankovskoye and Uglich Reservoirs. At the source of the river, the water is very soft, slightly mineralized, characterized by high color indicators (up to 400 degrees Pt-Co scale) and permanganate oxidation (60.3–72 mgO/L). In the Upper Volga Lakes, water mineralization increases to 110 mg/L, and the color of the water decreases significantly. In the Ivankovo Reservoir, higher concentrations of manganese and BOD5 are noted than in the Volga above Tver. Based on total phosphorus concentrations, the Upper Volga Reservoir (Lake Volgo) and the free-flowing section of the Upper Volga (from Selizharovo to Tver) belong to the “mesotrophic” class, and the Ivankovskoye Reservoir belongs to the “eutrophic” class. We characterize the Volga headwaters based on physico-chemical parameters “balanced” and discuss the relevance of “natural pollution”. Especially the free-flowing section comprises an important reference section for lowland rivers; thus, long-term monitoring of abiotic and biotic aspects is an important issue.

Research on the possibility of obtaining medium-carbon ferromanganese from the Djezdinskoe deposit

In this article, the results of laboratory studies on the smelting of medium-carbon ferromanganese using Djezdinskoe ores are presented. Kazakhstan has significant reserves of manganese ores represented by iron-manganese and carbonate-oxide ores. The manganese ores of the Djezdinskoe deposit are characterized by a relatively high manganese content (48%) and low iron content (2-5%). Sieve analysis was used to study the particle size distribution of the ore. Based on the results of the sieve analysis of ore samples obtained after sieving, a high manganese content (53.54%), low iron content (0.47%), and silicon dioxide content (2.25%) were identified. Laboratory experiments were conducted on smelting medium-carbon ferromanganese in the high-temperature Tamman furnace. According to the results of the laboratory experiments, it is recommended to use the size classes of -5.0 + 0.0 mm to obtain high-quality low-phosphorus silicon-manganese alloy and the size class of +5.0 to produce medium-carbon ferromanganese. The average chemical composition of the metal and slag is as follows: % Mn – 86 – 88; Si – 0.04 – 0.35; Fe – 1.78 – 2.0; P – 0.06 – 0.09; C – 1.5 – 2.0; MnO – 19-20; SiO2 – 13.94-14.5; CaO – 23.35 – 24.85; MgO – 13.25-14.0. Thus, an optimal technological scheme has been developed for the production of a wide range of manganese ferroalloys.

Hydrothermal synthesis of LiMn0.79Fe0.2Mg0.01PO4/C composite cathode materials using different Li3PO4 precursors

Doping and particle size controlling are two important approaches to improve the electrochemical performance of LiMnxFe1−xPO4 cathode materials. By employing a straightforward hydrothermal method and utilizing cost-effective lithium phosphate (Li3PO4) as the precursor, we successfully synthesized high Mn-content LiMn0.79Fe0.2Mg0.01PO4/C composites. The results reveal that the minute amount of Mg substantially enhances the electrochemical performance. In the subsequent mechanism study using Li3PO4 precursors with different particle size, we found that the nucleation process, dependent on specific surface area and diffusion rate, is likely to play a critical role for the size and morphology of formed LiMn0.79Fe0.2Mg0.01PO4. LiMn0.79Fe0.2Mg0.01PO4/C (LMFP-1), synthesized from initially smaller-sized and less agglomerated Li3PO4 (LPO-1), exhibited the most diminutive average particle size coupled with the highest specific surface area, which further facilitated electrolyte interfacial interaction and promoted Li+ diffusion kinetics. At 1C, LMFP-1 displayed a specific capacity of 110.7 mAh g−1, with 97.07% capacity retention after 200 cycles. This study provides pivotal insights for the synthesis of high-performance LiMnxFe1−xPO4 materials.

Associations of five blood heavy metals with hepatitis B virus infection and immunity in adults: a cross-sectional study

BackgroundHeavy metal pollution has emerged as a significant concern for human health, prompting increased awareness of its potential adverse effects. While previous research has established a connection between heavy metals and liver function biomarkers, the specific relationship between heavy metals and HBV infection remains unexplored. This cross-sectional study aims to investigate the potential correlations between five blood heavy metals - lead, cadmium, mercury, manganese, and selenium - and the presence of HBsAg, HBsAb, and HBcAb in adults.MethodsThe study utilized data from NHANES 2007–2018. Participants were classified into four groups based on their infectious status, and the association between heavy metals and HBV infection was analyzed using multiple logistic regression and stratification analysis.ResultsA total of 8431 participants were included, with 5 436 classified as Susceptible, 1 765 as Vaccinated, 865 as Natural Infection, and 103 as Acute/Chronic HBV Infection. The Vaccinated group exhibited a lower mean age (34.52 ± 14.16 years) compared to the other groups. Statistically significant differences in heavy metal concentrations (except selenium) were observed among the groups (P < 0.001). After adjusting for covariates, lead was significantly associated with HBV infection (Q2: OR 2.37, 95%CI 1.04–5.39; Q3: OR 2.34, 95%CI 1.01–5.40), and positive trends were observed for high blood concentrations of mercury (Q4: OR 3.03, 95%CI 1.31–7.04) and manganese (Q4: OR 2.52, 95%CI 1.20–5.28). Furtherly, the presence of lead reduced the protection of HBsAb (Q2: OR 0.84, 95%CI 0.73–0.97; Q3: OR 0.77, 95%CI 0.66–0.90; Q4: OR 0.83, 95%CI 0.70–0.98). Subgroup analysis indicated that cadmium was associated with an increased risk of HBV infection in Asians (OR 1.36, 95%CI 1.03–1.78) and individuals with a BMI range of 25 to 30 (OR 1.60, 95%CI 1.17–2.18).ConclusionsThe study’s findings suggest a correlation between elevated blood Pb concentrations and reduced immunization rates against hepatitis B. Individuals with a positive HBsAg exhibit lower blood Se concentrations and higher blood Hg and Mn concentrations.

Membrane Methods for Purification of Artesian Water with a High Content of Iron and Manganese

The effects of the main technological parameters, such as pressure, temperature of the separated solution on the process of ultrafiltration and reverse osmosis during the purification of artesian waters from iron and manganese compounds are considered.It was found that the use of ultrafiltration for pre-treatment and subsequent reverse osmosis is an effective way to obtain drinking water quality. The optimal technological diagram of artesian water treatment plants is shown.

Evaluation of the heavy metal levels from selected food cultivars, from coal mining communities of Enugu State, Nigeria

Food cultivars from Akwuke, Ngwo and Udi were analyzed for their heavy metal content using the atomic absorption spectrometry (AAS). The mean concentrations of Manganese in leafy vegetable ranges from 1170±6.20µg/g and in chromium from 110±0.0 µg/g, in lead from 320±210, in cadmium from 30±10 µg/g and nickel from 10±0 µg/g all in Akwuke. The transfer factors results for the three communities shows that the pumpkin leafy have the highest transfer factor for manganese, 2.6 in Akwukeand chromium yam 2.465 in Udi, while Nickel has the least transfer factor in all the food cultivars in the three communities with 0 result. This study has revealed high concentration of manganese, lead, chromium cadmium and nickel in food cultivars in the three studied area Akwuke, Ngwo and Udi, all in Enugu State. Though the concentrations of these heavy metals were not high in any of the soil samples, but high concentration of these heavy metals, compared to WHO/FAO in food cultivars were observed, especially in Udi and Ngwo community. Keywords: Heavy metal, levels, food cultivars, Enugu State and Nigeria

Evaluation of the heavy metal levels in soil and water from coal mining communities of Enugu State, Nigeria

Water and soil from Akwuke, Ngwo and Udi were analyzed for their heavy metal content using the atomic absorption spectrometry (AAS). All the well water samples were found to be higher in heavy metal concentration when compared with the WHO permissible limit, except nickel in drinking water. The soil samples in the three communities were found to have lower concentration of Mn, Cr, Pb, Cd, and Ni when compared to the WHO permissible limit in soil. This study has revealed high concentration of manganese, lead, chromium, cadmium and nickel in water samples in the three studied area Akwuke, Ngwo and Udi, all in Enugu State. Though the concentrations of these heavy metals were not high in any of the soil samples, but high concentration of these heavy metals, compared to WHO/FAO in well water was observed, especially in Udi and Ngwo community. Keywords: Heavy metal, levels, soil and water.

Effects of manganese concentration and temperature on the ferromagnetism of manganese‐doped gallium arsenide semiconductor

AbstractThe main objective of the review was to investigate the ferromagnetism of diluted magnetic semiconductors made of Mn‐doped GaAs. Manganese‐doped gallium arsenide has recently become an important field of research because of its potential applications in the fields of spintronics and magnetic devices. The magnetic moment caused by adding manganese to the GaAs crystal structure causes a low‐temperature ferromagnetic behavior. The main factor that affects the ferromagnetic properties of Mn‐doped gallium arsenic is manganese concentration. Understanding the relationship between Mn concentration and magnetic properties is important for material optimization in specific applications. It was found that Mn‐doped GaAs exhibit paramagnetic behavior below a specific critical concentration. However, the substance is transformed into a ferromagnetic state over the maximum concentration. The Curie temperature is an important additional factor influencing the ferromagnetic properties of Mn‐doped GaAs. The temperature at which a material ceases to exhibit ferromagnetic behavior is known as the Curie temperature. The Curie temperature of a material depends on its Mn concentration, thin film thickness, and degree of disturbance. A reduction in magnetic resistance increases the concentration of Mn‐treated gallium arsenic and increases its rate as it reaches its maximum value. High Curie temperatures are the result of stronger magnetic interactions resulting from higher manganese concentrations. The specific heat capacity of Mn‐doped gallium arsenide is influenced by its magnetic and structural contribution.

Food Application of Orange Seed Powder through Incorporation in Wheat Flour to Boost Vitamin and Mineral Profiles of Formulated Biscuits.

The significance of conducting research for its application has been noted as a result of the rising global food production and waste generation. As a result, there is increasing interest in fruits and vegetable seeds that contain bioactive chemicals, such as those that are obtained from orange seeds. In the current work, orange seed powder replaced wheat flour at 0, 2.5, 5, 7.5, and 10% levels, to observe changes in physicochemical features of developed biscuits. Proximate analysis of orange seed powder and wheat flour revealed that orange seed powder has high fat, fiber, protein, and ash contents as compared to wheat flour, whereas moisture contents in wheat flour were high. In developed biscuits, the highest values (percentage) of ash (9.68 ± 0.04), fiber (6.79 ± 0.12), protein (10.42 ± 0.25), and fat (36.90 ± 0.55) were found in biscuits developed with 10% orange seed powder. Orange seed powder was a comparatively good source of both macro and micro minerals, as compared to wheat flour. High contents of selenium (5.32 ± 0.03), iron (2.12 ± 0.05), zinc (3.88 ± 0.12), and manganese (2.25 ± 0.04) mg/100 g, present in orange seed powder, were the prominent findings of this research work, as wheat flours were observed to be deficient in these trace minerals. Contents of calcium, magnesium, potassium, zinc, manganese, zinc, and selenium in control biscuits were found 20.51 ± 0.08, 17.29 ± 0.04, 46.12 ± 0.05, 1.06 ± 0.01, 1.97 ± 0.01, 0.12 ± 0.01, and 0.11 ± 0.01 mg/100 g, respectively, and replacement of wheat flour with 10% orange seed powder increased values of these minerals to 103.90 ± 0.35, 44.35 ± 0.50, 71.29 ± 0.32, 2.59 ± 0.4, 2.75 ± 0.02, 1.31 ± 0.01, and 2.02 ± 0.05 mg/100 g, respectively. Vitamins E and K, which were not detected in wheat flour, were present in orange powder in high amount, whereas B group vitamins, which were also present in wheat flour, were observed in significantly high quantities in orange seed powder. Increment in vitamin A, D, E, K, and B complexes was significant as a result of orange seed powder supplementation, except for vitamins B1 and B2, which were slightly decreased. Sensory evaluation revealed that a 5% replacement of orange seed powder provided good quality biscuits with acceptable colour, flavor, taste, texture, and overall acceptability. Orange seed powder could prove an important ingredient in the baking industry with the potential of promoting the nutritional value of foods.

Assessment of Heavy Metal Contents in Some Common Spices Available in the Local Market of North Shewa Zone, Oromia Regional State, Ethiopia.

The objective of this study was to determine the contents of heavy metals in some common spices commercially available in the North Shewa Zone, Oromia region, Ethiopia. Korarima seed (Aframomum corrorima), ginger rhizome (Zingiber officinale), red pepper fruit (Capsicum annum), and turmeric rhizome (Curcuma longa) samples were randomly collected from the Fiche open market. These spice samples were digested using a mixture of 3mL of HNO3 (69-72%) and 1mL of HClO4 (70%), where organic components are assumed to decompose into gaseous forms while other heavy metal elements are left in the solution. The contents of heavy metals (Fe, Zn, Cu, Cr, Mn, Ni, Cd, and Pb) in the spices were determined by inductively coupled plasma‒optical emission spectrometry (ICP‒OES). The results obtained showed that the concentrations of heavy metal in the korarima, red pepper, ginger, and turmeric samples in milligrammes per kilogramme of dry weight were in the range of Fe (38.7-98.9), Mn (10.5-257), Zn (7.30-29.2), Cu (1.70-6.50), Cr (5.40-9.70), Cd (1.50-2.90), Pb (14.5-28.4), and Ni (3.90-6.70). The heavy metal contents in korarima, red pepper, ginger, and turmeric samples were compared with the maximum values given by the World Health Organization (WHO). Accordingly, the Fe, Zn, Cu, Cr, Mn, and Ni values in the spice samples were found to be lower than the maximum limit of the WHO, while the levels of Pb and Cd in four spice samples and Mn (only in ginger) were higher than the WHO permissible limit. Thisstudyshowsthatthe consumption of korarima, red pepper, ginger, and turmeric may pose a serious health threat to consumers due to the high content of lead, cadmium, and manganese (only in ginger) in spices. Therefore, it is suggested that further study be conducted on spice samples based on the origin of cultivation to determine which hotspot is responsible for high levels of contamination of lead, cadmium, and manganese to protect consumers.

Influence of welding conditions and flux composition on chemistry of welds using recycled steel slag in submerged arc welding

The slag generated by steel-making plant has been employed to manufacture flux essential for submerged arc welding process. The developed flux has been used for depositing beads on plates, and the weld metal chemistry has been evaluated. The effect of welding conditions and flux composition on element transfer behavior has been investigated. The experiments were carried out as dictated by the design matrix generated using CCRD in response surface methodology. The data generated during experimentation was used to develop mathematical models. The developed models were tested for their adequacy through the ANOVA technique in design expert software. It is interesting to note that the recycled slag provided the chemistry of weld metal which is accepted as per ASME specifications. The rise in welding current increases the amount of carbon in weld metal from 0.11 to 0.14 wt.%, whereas it decreases with increasing travel speed. Manganese content decreases (1.28 wt.% to 0.795 wt.%) with increasing welding current (250 A to 650 A). The increase in welding speed from 4.44 mm/s to 8.88 mm/s results in an increment in manganese content from 0.87 wt.% to 1.21 wt.%. Since increasing travel speed decreases heat input per unit length of the weld, evaporation of manganese is suppressed. Therefore, the highest manganese content was achieved at a lower current (250 A) and higher speed (8.88 mm/s). Smooth beads with evenly distributed ripples free from surface defects like undercuts, porosity, pockmarks, etc., were achieved.

Influence of citric acid on the extraction level of manganese in green and black tea infusions

Manganese concentration in green and black tea (10 samples of each type) was determined by means of graphite-furnace atomic absorption spectrometry. Both the dry leaves and the infusions were analysed. The concentration of manganese in dry leaves was in the range of 502–1277 mg · kg−1 for black tea and 798–1906 mg · kg−1 for green one. Since lemon juice is commonly added for tea to enrich its taste, citric acid was used to simulate lemon juice influence on manganese concentration in the infusions. The infusions prepared with and without citric acid addition were analysed and the results showed significant influence of citric acid on manganese leaching. The average extraction levels of manganese from black tea equal 16% (for non-acidified infusions) and 34% (for acidified ones) while these values for green tea equal 13% and 38%, respectively. Statistical evaluation of the results showed that the differences between acidified and non-acidified infusions were statistically significant. High manganese content makes the tea an important source of manganese in human diet.

Characterization and properties of manganese oxide film coated clinoptilolite as filter material in fixed-bed columns for removal of Mn(II) from aqueous solution

A new filter material, manganese oxide film coated clinoptilolite (MOFCC), was characterized and introduced to explore the effect in treating high concentration of manganese (1.71–2.12 mg L−1) from aqueous solution in fixed-bed column. Adsorption behavior of Mn(II) can be approximately described with the Langmuir isotherm. During the continuous 30 days filtration experiment, the removal rate of Mn(II) has maintained to be above 95.51%, the accumulated removal amount (806.42 mg) is much higher than the theoretical adsorption capacity (89.71 mg), which indicated that the removal of manganese by MOFCC includes both adsorption and auto-catalytic oxidation process, and it does not require a start-up period. SEM, EDS, XPS, XRD, ZETA potential and BET analyses were used to observe the surface properties of MOFCC. The manganese oxide film of MOFCC exhibits in clusters, apparently on occupied surface, the main component of the manganese oxide film is (Na0.7Ca0.3)Mn7O14·2.8H2O, the specific surface area of MOFCC is 38.76 m2 g−1, and the pore size is concentrated in the range of 3–40 nm, within the mesoporous range mesopores. pHpzc (point of zero charge) value is about 2.36. The characteristics of MOFCC make it an excellent manganese removal filter material for water treatment plant. Therefore, there is a long-term practical significance to develop new system for deep removal of manganese based on MOFCC.

Experimental study on the performance of the dielectric barrier discharge technique in the treatment of simulated groundwater with high iron and manganese content

Abstract Groundwater with high concentrations of iron and manganese is harmful to the human body and modern industries. Conventional methods of treating iron and manganese have the disadvantage of high costs and complex control processes. A dielectric barrier discharge (DBD) water treatment system was built to remove iron and manganese from groundwater in this paper. Single-factor experiments were used to analyze the effect of discharge power, initial iron and manganese concentrations, gas flow rate, liquid flow rate, initial pH, flocculant and capture agent process parameters on iron and manganese removal rates. It was found that Fe2+ removal rates can reach 97.31% and Mn2+ removal rates can reach 81.42% when the initial concentrations of Fe2+ and Mn2+ are 6 and 3 mg/L, respectively. The use of 10 mg/L NaHCO3 or 5 mg/L Ca(OH)2 increased the removal rate of Fe2+ to 99% but had no effect on the removal rate of Mn2+. It was found that the optimum treatment time for Mn2+ was different for different process parameters, mainly in the range of 9–15 min, which needs to be noted in future production applications. This work shows that DBD can effectively remove iron and manganese ions from groundwater and analyzes the removal mechanism.

Ecological risk assessment of potentially toxic elements (PTEs) in agricultural soils of western Iran using geochemical data and statistical analysis

ABSTRACT Environmental pollution is a serious problem in many parts of the world, especially in developing countries such as Iran. This study was conducted to investigate chemical pollution by selected heavy metals in the southern cities of Hamadan province, west of Iran including Malayer, Toyserkan, and Nahavand. A total of 90 soil samples were collected from a depth of 0 to 30 cm of agricultural lands. The state of soil pollution was analyzed using geochemical indicators, pollution coefficient, pollution level, and potential ecological risk indices. The highest concentration of arsenic and cadmium in the soil of city of Toyserkan with an average of 19.46 and 0.25 mg kg-1 respectively, and the highest concentration of iron, cobalt, chromium, and antimony in the soil of city of Malayer with an average of 4.36, 20.8, 114.67 and 4.62 mg kg-1 respectively, and the highest concentrations of manganese, copper, and nickel in the soil of city of Nahavand were 268.95, 38.58, and 81.83 mg kg-1, respectively. The results showed that there was a significant difference between the average concentrations of the measured metals in the three cities. In all the studied cities, Mueller's geochemical index was in the non-polluted category, the pollution coefficient was in the low to medium pollution category, the pollution index was in the very low to high pollution category, and the environmental risk index for metals was in the low to very high environmental risk category. Investigation of pollution indicators showed that the soils of the studied areas are about to be polluted with heavy metals. Therefore, it is necessary to consider environmental aspects to reduce and prevent irreparable damage to the soil and the environmental cycle in the long run.

Influence of β-casein genotype on physicochemical properties and functionality of bovine milk

Several studies have been focused on the effect of milk protein genetic variants on milk physicochemical properties and functionality in recent years. β-casein, an important protein related to milk processibility, has been reported to have 2 main genetic variants A1 and A2, for which cows may be homozygous or heterozygous. In this study, several physicochemical properties of milk with β-casein variants A1A1, A1A2, and A2A2 from 3 collection occasions were analyzed. Higher manganese content and lower pH were found to be associated with the A1A1 variant compared with the other 2 genotypes. Better rennet and acid coagulation were found in A1A1 milk compared with A1A2 and A2A2 milk (although P > 0.05), whereas A2A2 milk was more stable to creaming compared with the other 2 genotypes, which may be linked to its smaller fat globule size. Thus, milk from cows with A1A1 genotype could be preferable for cheese making, while that with A2A2 variant can be used in formulations requiring good stability against creaming, and for example, yogurt making, where the softer yogurt texture may be easier to digest.

Linkages between Soil Acidity, Soil Plant Nutrients and Land Use on Ferralsols in Central Uganda

A study to examine the linkages between soil acidity, soil plant nutrients and land use on Ferralsols was carried out on smallholder farms in Central Uganda. The objective of the study was to assess the effect of soil pH on soil plant nutrient availability under the current land use. The study was carried out in Mpigi, Masaka, Wakiso, Mukono and Mubende districts representing Central Uganda. Soil samples were randomly collected from Coffee, Banana, soybean, common bean, maize and virgin fields in the five districts and the pH and plant nutrient analyzed accordingly. The analysis of variance (ANOVA) showed significant difference (p&lt;0.01) on soil nitrogen, Calcium (p&lt; 0.05) and Magnesium (p&lt; 0.05). When treatment was assessed, the study showed significant difference (p&lt; 0.01) on potassium. Besides, the study also showed high concentrations of Manganese (Mn) and Iron (Fe) in addition to very high sand and low silt and clay contents. The current land use for coffee production in Masaka district recorded the lowest soil pH (4.4) followed by annual fields (pH 4.60) in Mpigi. The highest soil pH (5.7) was recorded in banana fields in Mubende. The study also recorded very low to low N, P and K. Generally, the study observed rapid soil fertility decline in smallholder farms in the region.

SAE 1026

Abstract 1026 is a wrought low-carbon (carbon = 0.22-0.28%) non-alloy steel that has a higher manganese content (manganese = 0.60-0.90%) than 1025 (manganese = 0.30-0.60%). It is used in the normalized, cold worked, or quenched and tempered condition. 1026 may also be nitrided or nitrocarburized. This steel is widely used for small, moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications that require a combination of moderate strength, high toughness, and good fabrication characteristics. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on forming and heat treating. Filing Code: CS-255. Producer or source: Heat Treater's Guide.

Removal of Fe and Mn from the groundwater by using zeolite with Rossellomorea sp.

Groundwater is one of the alternatives to surface water that can be used for drinking water; however, it normally exists with high iron and manganese content. In this study, a column study was conducted to observe the elimination of iron (Fe) and manganese (Mn) in the groundwater under different retention times by using zeolite immobilised with iron-oxidising bacteria (IOB). Rossellomorea sp. representing an IOB, was found from the isolation process and was further cultured in the laboratory for immobilization into the natural zeolite as replacement materials for the sand filter. When the zeolite assisted with the Rossellomorea sp. was used, the elimination of Fe and Mn were 99.34% and 88.92%, respectively, compared to the removal of Fe and Mn, which were 93.62% and 93.73%, respectively, for media without immobilization. The presence of Rossellomorea sp. enhances the Fe oxidation, resulting in high removal of Fe. The Thomas and Yoon-Nelson models were performed in both raw zeolite and zeolite with IOB. The total coliform (MPN) increased from 70.8 to 307.6 MPN/100 mL due to the Rossellomorea sp. present that promotes the growth of coliform bacteria. In conclusion, the immobilization of zeolite with IOB is a potential technique to extract the Fe and Mn in the groundwater.