High Load Research Articles

Monitoring bridge bearings based on rubber-based composite materials

To improve the real-time monitoring capability of bridge structure safety, intelligent bridge bearings were prepared based on rubber based composite materials. The study selected T4/3-5 intelligent rubber bearings and conducted a systematic experimental analysis on their response characteristics under different loading speeds and holding states. By measuring the displacement and resistance changes of the intelligent bearings under various load conditions, their sensitivity and stability were evaluated. These experiments confirmed that the T4/3-5 intelligent rubber bearings exhibited a total creep deformation of approximately 1 mm and 1.5 mm under loads of 60 kN and 45 kN, respectively. This suggests that the molecular chains reach a relatively stable configuration under high loads and are not prone to further changes. Moreover, the resistance reduction ratio under a load of 60 kN is approximately 0.57, while under a load of 45 kN it is approximately 0.62, indicating that nickel powder particles in the composite material form a more stable conductive network after molecular rearrangement. At different loading rates, the displacement-load and load-resistance curves of the bearings show consistent trends, and the creep and resistance relaxation behaviors exhibit certain regularity with the concentration of load size. Through the analysis of these data, the study elucidated the resistance change mechanism in the bearings and validated the feasibility of intelligent bearings as a real-time load monitoring tool.

Preparation method and industrialization of Ta-based ultra high temperature ceramic Tujia jar tea baking jar materials

The production materials of traditional Tujia jar tea often face problems such as poor high-temperature performance and poor durability. To improve the temperature resistance and durability of tea baking utensils, this study proposes a new type of TaC ultra-high temperature ceramic. TaC ceramics with excellent performance were prepared through powder metallurgy technology, including high-energy ball milling to ensure uniform mixing, followed by compression molding and high-temperature sintering. The test results demonstrated excellent mechanical properties, with a maximum depth of 948.67 nm and a contact depth of 954.45 nm, proving outstanding compressive and wear resistance. The hardness reached 21.4±0.5 Gpa, and the elastic modulus was 397.2±8.7 Gpa, both of which indicate its stability under high loads. In addition, the fracture toughness was 2.8±0.2 Mpa*m1/2. At a high temperature environment of 1000 °C, the oxidation rate constant of TaC ceramics was only 0.183 mg2 *cm−4 *h, which demonstrates its excellent high-temperature stability. The development of this TaC ceramic not only strengthened the traditional production process of Tujia teapots and tea roasting teapots, thereby improving the product’s service life, but also holds potential for other industrial applications that demand ultra-high temperature stability. These contributions provide new directions for the high-temperature application of ceramic materials and bring tangible economic and technological value to related industries.

Strategic electromagnetic interferences suppression in boost converters: zero-switch techniques

This article delves into the growing demand for efficient power conversion technologies accompanying the rise in electric vehicle (EV) adoption. Boost converters, essential for increasing the battery pack voltage to propel EV motors, pose a challenge due to the electromagnetic interference (EMI) generated by the high switching frequency of power devices. To address this issue, practitioners employ zero-voltage switching (ZVS) and zero-current switching (ZCS) techniques. In this comparative study, we systematically evaluate the effectiveness of these soft switching techniques in reducing conducted EMI in boost converters designed for EV applications. The results illuminate the potential of both ZVS and ZCS in significantly mitigating EMI emissions when compared to conventional hard-switching methods. Notably, ZVS soft switching emerges as more efficient and effective, particularly under higher loads, while ZCS soft switching excels in reducing EMI at lighter loads. In conclusion, the study asserts that ZVS soft switching presents a more promising solution for curtailing conducted EMI in boost converters for EV applications, particularly in high-load scenarios. However, it underscores the importance of considering specific operational conditions when deciding between the two techniques.

Enhancing heat transfer performance of aluminum-based vapor chamber with a novel bionic wick structure fabricated using additive manufacturing

Given the lightweight nature and excellent thermal conductivity of aluminum, it offers significant potential for light-weighting of phase-change cooling components. To further enhance the thermal performance of aluminum-based vapor chambers, this study utilized selective laser melting (SLM) to design and integrally manufacture the slightly oleophilic wick for the condenser of the aluminum-based vapor chamber, along with three different superoleophilic wick structures for the evaporator: the gyroid bionic composite porous wick vapor chamber (GBCPVC), the groove composite porous wick vapor chamber (GCPVC), and the uniform porous wick vapor chamber (UPVC). A water-cooling experimental setup was established, and the effects of wick structure, cooling water flow rate, and cooling water temperature on the maximum heat load, temperature uniformity, and thermal resistance of vapor chambers were systematically investigated. The results indicated that the gyroid bionic porous wick structure significantly enhanced the thermal performance of the vapor chamber. Under the same conditions, GBCPVC exhibited lower thermal resistance and superior temperature uniformity, achieving a higher heat load than GCPVC and UPVC. When the cooling water temperature was decreased, its maximum heat load significantly increased. Specifically, at 15 °C, the maximum heat load for GBCPVC reached 300 W, an increase of 33.33 % and 53.33 % compared to 25 °C and 35 °C, respectively. Conversely, a rise in cooling water temperature enhanced the temperature uniformity and reduced thermal resistance of CBCPVC. At 35 °C and a heat load of 120 W, GBCPVC achieved a minimum thermal resistance of 0.034 K/W and a maximum temperature difference of 1.46 °C. Additionally, an increased flow rate enhanced the maximum heat load of GBCPVC, and under high heat loads, it could also reduce the thermal resistance and improve temperature uniformity. This study provides new insights and solutions for the thermal management of phase-change cooling components in aerospace electronic devices.

The Perpetual Impact of COVID-19 on the Geriatric Population's Quality of Life and Potential Preventive and Therapeutic Measures in Unani Medicine: An Evidence-based Review

Background: COVID-19 pandemic has affected the elderly population more severely than many other patient groups. Due to their constitutional weakness and co-morbidities, geriatric populations are more prone to complications and adverse outcomes, especially with a high viral load. The Unani system of medicine encompasses several guidelines for the prevention and treatment of epidemics, which are stratified for different types of people with respect to age, geography, and health status, among others. Objective: Since Unani drugs are both safe and efficient, it has been found that demand for them has surged since COVID. This paper aims to discuss the various immunomodulatory, longevity-promoting agents, and organ-specific tonics specified in Unani medicine for the care of the elderly, which may be helpful during epidemics, and also, to present the scientific evidence of their efficacy. Methods: A thorough assessment of the available literature was carried out utilizing several electronic databases, including PubMed, Science Direct, Web of Science, Wiley Online, Google Scholar, and Springer Link, using the terms "Geriatrics," "Elderly," "SARS-CoV-2," "Unani," and many others, up until October 2022. A total of 61 pertinent reviews were included. To gather information on epidemics and their specific response in geriatrics, monographs in Urdu, Arabic, and English were explored in addition to classic Unani texts such Al-Qanun fit Tibb (The Canon of Medicine), Kamil-us-Sana'at (Liber Regius), Kitab al-Hawi fit Tibb (Liber Continence), and others. Plant names were confirmed by “The Plant List” (www.theplantlist.org). Results: During pandemics, Unani medicine aims to promote and preserve the health of the elderly by regulating six important factors (Asbāb Sitta Ḍarūriyya), which include adopting a specific diet, regimen and drugs as effective prophylactic strategies. However, the role of Unani medicine in immunological regulation relies on major organ protection, viz., general body tonic, nervine tonic, heart tonic, and liver tonic. Several Unani single drugs, such as Sibr (Aloe barbadensis Mill.), Zafran (Crocus sativus L.), and Mur (Commiphora myrrh Nees.), and formulations, such as Khameera Marwareed, Tiryaq-i- Arba, and Habb-i- Jadawar have also been found to be very effective in validated scientific preclinical and clinical studies. Furthermore, Unani drugs have anti-inflammatory, analgesic, and tonic actions, contributing to their holistic efficacy. Conclusion: It is observed in this review that Unani medicine employs a holistic approach to the health protection of the elderly. There are various dietary recommendations, lifestyle modifications, regimental therapy, and pharmacotherapy prescribed as per the individual’s requirements and needs to reduce geriatric mortality in times of epidemics. Modern pharmacological studies have discovered many bioactive compounds in health-protective drugs prescribed in Unani medicine, such as Vitis vinifera L., Ziziphus jujube Mill., and many others, further substantiating the literature.

Performance of metal circular tube under different loading amplitudes and dynamic resistance-yielding mechanism

As coal mining depth increases, the characteristics of “high ground stress, high ground temperature, high osmotic pressure, and mining disturbance” become increasingly pronounced, posing new challenges to the stability of the surrounding rock roadway. Amplitude is a key parameter affecting disturbance strength. A cyclic loading and unloading experiment was conducted under different amplitudes to explore the effect of metal circular tubes, used as energy-absorbing components, on the protection performance of anchor bolt tails. This experiment further revealed the competitive protection mechanism of the metal circular tube, termed “resistance - yielding”. The research results indicate that the metal tube incurs damage and accumulates it with the increase of loading amplitude in the pre-peak stage, leading to a decrease in its peak load. The metal tube absorbs external energy robustly through its elastic-plastic deformation. In the platform stage, a high amplitude load causes the peak load displacement to increase and its stable energy-absorbing stroke to decrease. Plastic energy dominates the main position of energy absorption, and the metal circular tube forms a dynamic competitive relationship of “resistance-yielding” with external stresses. Throughout the entire energy absorption process, the total energy absorption decreases with the increase of amplitude. The research results investigate the effect of amplitude on the performance of metal circular tubes and demonstrate the feasibility of applying metal circular tubes as energy-absorbing members at the end of anchor rods, which can provide theoretical guidance for the prevention of disaster accidents in mines caused by disturbances.

Lesion-symptom Mapping of Acceptability Judgments in Chronic Poststroke Aphasia Reveals the Neurobiological Underpinnings of Receptive Syntax.

Disagreements persist regarding the neural basis of syntactic processing, which has been linked both to inferior frontal and posterior temporal regions of the brain. One focal point of the debate concerns the role of inferior frontal areas in receptive syntactic ability, which is mostly assessed using sentence comprehension involving complex syntactic structures, a task that is potentially confounded with working memory. Syntactic acceptability judgments may provide a better measure of receptive syntax by reducing the need to use high working memory load and complex sentences and by enabling assessment of various types of syntactic violations. We therefore tested the perception of grammatical violations by people with poststroke aphasia (n = 25), along with matched controls (n = 16), using English sentences involving errors in word order, agreement, or subcategorization. Lesion data were also collected. Control participants performed near ceiling in accuracy with higher discriminability of agreement and subcategorization violations than word order; aphasia participants were less able to discriminate violations, but, on average, paralleled control participants discriminability of types of violations. Lesion-symptom mapping showed a correlation between discriminability and posterior temporal regions, but not inferior frontal regions. We argue that these results diverge from models holding that frontal areas are amodal core regions in syntactic structure building and favor models that posit a core hierarchical system in posterior temporal regions.

Healthy and diseased tensile mechanics of mouse lung parenchyma

The mechanics of the lung, consisting of high deformation, non-linear, rapid and cyclic loading, remain a critical unknown, hindering advancements in the field despite the pressing urgency of incurable and often fatal pulmonary diseases; such multi-scale ailments impair organ mechanical function by inducing tissue-level alterations. Here, the tensile mechanics of healthy and diseased murine lung parenchyma with induced variable fibrosis and emphysema are compared—exploring multi-rate and directional tissue elasticity and energetics. Remarkably, parenchymal tissue is found to be notably elastic and non-hysteresis prone. Additionally, chronic fibrosis-induced tissues reveal significantly reduced compliance compared to age-matched controls, indicating characteristic stiffening; moreover, maximum stress tends to be greater in exposed than controls. Emphysematous tissues tend to show lower maximum stress than controls, reflective of hallmark tissue destruction and softening. Furthermore, faster loading rate is found to generally yield elevated stiffness and maximum stress, significantly for fibrosis group exposed tissue—this interdependence between loading rate and tissue disease is notable considering the dynamics of breathing. Generally, control tissues are found to be isotropic, as are emphysematous tissues, but fibrosis may lead to increased anisotropy. Additionally, fibrotic and mature-healthy lungs are found to show age effect trends, such as increased strain energy. Along with these findings, this study additionally facilitates future analyses of other diseases by establishing lung biaxial testing protocols for small-scale murine specimens, which can serve as practical and ethical models for exploring human diseases. Overall, this study offers fundamental material characterizations which will enable future formulations of experimentally informed computational models.

Rail Structural Health Monitoring using ultrasonic guided waves: system design and deployment

Railways are a central industrial infrastructure enabling people and goods transportation all across the globe and their use is due to increase in the forthcoming years to reduce the overall carbon footprint of our modern societies. Hence the need to ensure their reliable use, as traffic interruptions or accidents can have dire social, economic and environmental impacts. In particular, rail breaks can produce such incidents and need to be monitored and prevented if possible. Ultrasonic guided waves are a promising physical phenomenon to monitor rails as they can enable the monitoring of long portions with a limited number of sensors. This talk will present a SHM system relying on such waves for rail monitoring which has been deployed for industrial tests on a subway line. The electronics, the sensors and their coupling to the rail were optimized to ensure the measurement of guided waves after a long-range propagation throughout the life of the system. Indeed, specific couplings are needed to enable long-time coupling, and so ultrasound sensitivity of the system, while the rails are bearing high loads or dilating due to temperature changes. An experimental campaign was carried out to evaluate the sensitivity of the system to rail breaks, and to demonstrate its detection under representative, uncontrolled environmental conditions. Particular considerations linked to pulse-echo inspections, inducing a sensitivity to cut-off frequencies and zero-group velocity modes, will be presented.

Design and Analysis of Composite Rocket Motor Casing

Abstract: Rocket motors are widely employed to provide thrust, or impulsive force, which gives the flight vehicle a chosen velocity and facilitates delivery to the intended destination. Newton's second and third principles make up the majority of the rocket motor's operating principle. As a non-air inhalation propulsionclass, rocket motors do not require atmospheric oxygen for the combustion of the fuel that is stored inside of them. The motor hardware is going to be exposed to high temperatures and pressure loads during operation. In order to verify the rocket motor's temperatures and stress levels, structural and thermal design must be completed for the specified input parameters. This study has been approved for publication with structural

High Selenium Loading in Vertically Aligned Porous Carbon Framework with Visualized Fast Kinetics for Enhanced Lithium/Sodium Storage

AbstractLithium/sodium–selenium (Li/Na–Se) batteries with high volumetric specific capacity are considered promising as next‐generation battery technologies. However, their practical application is hindered by challenges such as low Se loading in cathodes and the polyselenides shuttle effect. To address these challenges, a new Se host is introduced in the form of a free‐standing N, O co‐doped vertically aligned porous carbon framework decorated with a carbon nanotube forest (VCF‐CNTs), allowing for high mass loading of up to 16 mg cm−2. The low‐tortuosity Se@VCF‐CNTs architecture facilitates rapid lithiation/sodiation kinetics, while the CNT forests in vertical microchannels enhance efficient Se loading and serve as a multi‐layer fence to prevent undesired polyselenide shuttling. Consequently, the Se@VCF‐CNTs cathode displays a significant areal capacity of 10.3 mAh cm−2 at 0.1 C with a Se loading of 16 mg cm−2 for Li–Se batteries, exceeding that of commercial lithium ion batteries (4.0 mAh cm−2). In Na–Se batteries, the Se@VCF‐CNTs electrode with a Se loading of 5 mg cm−2 exhibits a discharge capacity of 436 mAh g−1 after 200 cycles, proving its consistent cycling performance. This study enriches the field of knowledge concerning high‐loading Se‐based battery systems, offering a promising avenue for enhancing energy density in the field.

Construction of bupivacaine-loaded gelatin-based hydrogel delivery system for sciatic nerve block in mice.

Peripheral nerve blockade (PNB) is a common treatment to relieve postoperative pain. However, local anesthetics alone have a short duration of action and severe side effects during postoperative analgesia. In order to overcome these limitations, the present study reported an injectable hydrogel with a drug slow-release profile for regional nerve blockade. The injectable hydrogel was prepared by crosslinking with gelatin and NHS-PEG-NHS, which was degradable in the physiological environment and displayed sustainable release of anesthetics locally, thus improving the disadvantage of the high toxicity of local anesthetics. In this regard, we conducted a series of in vitro characterizations and proved that the hydrogel has a porous three-dimensional mesh structure with high drug loading capability, and sustainable drug release profile. And cytotoxicity experiments confirmed the good biocompatibility of the hydrogel. It was shown that using the animal sciatic nerve block model, the analgesic effect was greatly improved in vivo, and there was no obvious evidence of permanent inflammation or nerve damage in the block site's sections. This locally slow-release platform, combined with local anesthetics, is therefore a promising contender for long-acting analgesia.

Identification of deep Czech Republic–Austria transboundary aquifer discharge and associated river chloride loading

The deep transboundary aquifer of regional scale along the Czech Republic–Austria border in Central Europe serves as a thermal-mineral water resource for balneotherapy and plays an important role in the region’s development. The aquifer is composed mostly of Jurassic carbonates at depths from 160 to − 3000 masl. Despite more than two decades of exploitation, no complex analysis of groundwater flow directions and groundwater fluxes ever took place. Now, cross-border cooperation enabled the research team to gather crucial information on the Jurassic aquifer. For a better understanding of the groundwater flow system, a numerical model was developed. To simulate the effect of variable density and viscosity occurring in such a deep aquifer, the SEAWAT numerical model was used. The simulation shows that there is an inflow of low mineralised groundwater from the crystalline outcrops in the northwest and inflow of saline groundwater from southeast. Aquifer discharge was identified along the zone partly corresponding to the course of the Dyje River. To check the model’s accuracy, the river water was sampled together with streamflow measurements. Detected sections of increasing chloride concentration indicate zones of the Jurassic aquifer discharge into the Dyje River. The discharge rate of 85 L/s derived from streamflow and chloride concentrations matches the value computed by the model. The relatively high discharge of the Jurassic aquifer contributes significantly to the high chloride loading observed in the Dyje River.

Localized High-Concentration Sulfone Electrolytes with High-Voltage Stability and Flame Retardancy for Ni-Rich Lithium Metal Batteries.

The localized high-concentration electrolyte (LHCE) propels the advanced high-voltage battery system. Sulfone-based LHCE is a transformative direction compatible with high energy density and high safety. In this work, the application of lithium bis(trifluoromethanesulphonyl)imide and lithium bis(fluorosulfonyl)imide (LiFSI) in the LHCE system constructed from sulfolane and 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether (TTE) is investigated. The addition of diluent causes an increase of contact ion pairs and ionic aggregates in the solvation cluster and an acceptable quantity of free solvent molecules. A small amount of LiFSI as an additive can synergistically decompose with TTE on the cathode and participate in the construction of both electrode interfaces. The designed electrolyte helps the Ni-rich system to cycle firmly at a high voltage of 4.5V. Even with high mass load and lean electrolyte, it can keep a reversible specific capacity of 91.5% after 50 cycles. The constructed sulfone-based electrolyte system exhibits excellent thermal stability far beyond the commercial electrolytes. Further exploration of in-situ gelation has led to a quick conversion of the designed liquid electrolyte to the gel state, accompanied by preserved stability, which provides a direction for the synergistic development of LHCE with gel electrolytes.

Surface Electron Reconstruction of Catalyst Through Alloying Strategy for Accelerating Sulfur Conversion in Lithium‐Sulfur Batteries

AbstractAlloy catalyst is considered to be an important strategy to solve the shuttle effect and sluggish kinetics of lithium‐sulfur batteries (LSBs). However, the effect of the electronic structure of the alloy catalyst on the sulfur conversion process has not been effectively analyzed. In this paper, based on alloying strategy, the electronic structure of such a FeCoNi catalyst is regulated and optimized, and the sulfur adsorption configuration and catalytic conversion process are defined. The in situ Raman spectroscopy and the density functional theory (DFT) are employed to deeply understand the catalytic mechanism of such a sulfur conversion. A cell with FeCoNi modified separator delivers an ultra‐low capacity attenuation of 0.056% per cycle over 1000 cycles at 3 C. The outstanding anti‐self‐discharge performance of 8.1% over 7 days is also achieved. Furthermore, the obtained cell with a high sulfur loading of 9.7 mg cm−2 and lean electrolyte of 5.6 µL mgs−1 exhibits 81% capacity retention after 100 cycles, providing a research prospect for the practical application of lithium‐sulfur batteries.

Optimization of mixed cargo allocation and stowage with heterogeneous vehicles

In order to solve the problem of low efficiency and high loading costs in business logistics and distribution operations, this paper classifies non-standard cargoes based on their spatial and temporal characteristics. Based on this, a dual-layer planning model for multi-vehicle cargoes loading and transportation is constructed to jointly optimize the loading process. This paper designs a space-inspired heuristic algorithm to solve the model and verifies the feasibility of the model. The results show that compared to a single vehicle type, the joint optimization of multi-vehicle combinations for loading and transportation has stronger adaptability and can better accommodate changes in cargo volume. Compared to the single vehicle type, not only did the loading rate increase by 18%, but also effectively reduced the transportation cost by 3%. Different proportions of spatial and temporal characteristic cargoes have different effects on the loading and transportation. Adjusting the proportion of cargoes that can be placed on both upper and lower layers to 50% can better utilize transportation resources such as vehicles. Increasing the proportion of urgent cargoes can improve the economic efficiency of loading and transportation.

Vertical transmission of SARS-CoV-2 delta-variant in a preterm infant

BackgroundAs SARS-CoV-2 continues to be relevant and cause illnesses, the effect of emerging virus variants on perinatal health remains to be elucidated. It was demonstrated that vertical transmission of SARS-CoV-2 is a relatively rare event in the original SARS-CoV-2 strain. However, very few reports describe vertical transmission related to the delta-variant.Case presentationWe report a case of a preterm male neonate born to a mother with positive SARS-CoV-2 and mild respiratory complications. The neonate was born by cesarean section due to fetal distress. The rupture of the amniotic membrane was at delivery. The neonate had expected prematurity-related complications. His nasopharyngeal swabs for RT-PCR were positive from birth till three weeks of age. RT-ddPCR of the Placenta showed a high load of the SARS-CoV-2 virus with subgenomic viral RNA. RNAscope technique demonstrated both the positive strand of the S gene and the orf1ab negative strand. Detection of subgenomic RNA and the orf1ab negative strand indicats active viral replication in the placenta.ConclusionsOur report demonstrates active viral replication of the SARS-CoV-2 delta-variant in the placenta associated with vertical transmission in a preterm infant.

Vitrified Metal-Organic Framework Composite Electrolyte Enabling Dendrite-Free and Long-Lifespan Solid-State Lithium Metal Batteries.

Solid-state lithium metal batteries (LMBs) are still plagued with low ionic conductivity and inferior interfacial contact, which hinder their practical implementation. Herein, a quasi-solid-state composite electrolyte, poly(1,3-dioxolane) (PDOL)/glassy ZIF-62 (PGZ) with fast ion transport and intimate interface contact, is fabricated via in situ polymerization. The in situ polymerization of DOL in an electrolyte matrix not only improves the exterior interface between electrolyte/electrode but also optimizes the inner interfaces among glassy particles, rendering PGZ as an uninterrupted ionic conductor. Moreover, PGZ inherits the superior ionic conductivity and the robust dendrite prohibition of glassy MOFs originating from their grain-boundary-free nature, isotropy, and abundant groups containing N species. As expected, our proposed PGZ exhibits a prominent ionic conductivity of 6.3 × 10-4 S cm-1 at 20 °C. Li|PGZ|LiFePO4 delivers an outstanding rate performance (103 mAh g-1 at 4C) and a stable cycling capacity (118 mAh g-1 at 1C over 1000 cycles). PGZ also presents excellent low-temperature cycling performance with 75 mAh g-1 for 480 cycles at -20 °C and excellent flame retardance. Even at a high loading of 12.1 mg cm-2, it can still discharge at 140 mAh g-1 for 100 cycles. Hence, PGZ prepared via in situ polymerization holds enormous prospects as a solid-state electrolyte for high-performance and safe LMBs.

Microenvironment Reconstitution‐Induced Collaborative Oxyanions‐Vacancies Engineering for Enhanced High‐Mass‐Loading Energy Storage

AbstractPerformance breakthrough of energy‐storage electrodes under commercial‐level mass loading (≥10 mg cm−2) are highly pursued but restricted by sluggish mass/charge transfer rates and kinetically unfavorable reaction sites. In response, through electrochemical microenvironment reconstitution, these limitations are broken by engineering synergy between vacancies and oxyanions in the active matrix (Rec‐NiCoExch), which showcases a record‐level areal capacitance of 10.9 C cm−2 with a high mass loading of 20 mg cm−2 and a retention of 72% at 100‐fold current density. Such a design further endows the hybrid supercapacitor with an areal capacity of 20.9 C cm−2 and an energy density of 4.6 mWh cm−2, outperforming most of the benchmark results. Theoretical calculation reveals that in situ evolved oxyanions not only act as the effective adsorption sites but also secure the oxygen vacancies, enabling the potential synergy toward improved electronic conductivity and enhanced reactivity of Ni sites. As a proof‐of‐concept, the as‐assembled quasi‐solid‐state micro‐supercapacitor deliveries an ultrahigh energy density of 111.5 µWh cm−2 and presents great potential in intermittent energy storage by the solar panel‐supercapacitor‐LED system. This work offers insights for constructing commercial‐level energy‐storage electrodes by mastering surface/interface engineering for practical applications.

Ru Single Atom Dispersed on MoS2/MXene for Enhanced Sulfur Reduction Reaction in Lithium-Sulfur Batteries.

The high theoretical energy density (2600 Whkg-1) and low cost of lithium-sulfur batteries (LSBs) make them an ideal alternative for the next-generation energy storage system. Nevertheless, severe capacity degradation and low sulfur utilization resulting from shuttle effect hinder their commercialization. Herein, Single-atom Ru-doped 1T/2H MoS2 with enriched defects decorates V2C MXene (Ru-MoS2/MXene) produced by a new phase-engineering strategy employed as sulfur host to promote polysulfide adsorption and conversion reaction kinetics. The Ru single atom-doped adjusts the chemical environment of the MoS2/MXene to anchor polysulfide and acts as an efficient center to motivate the redox reaction. In addition, the rich defects of the MoS2 and ternary boundary among 1T/2H MoS2 and V2C accelerate the charge transfer and ion movements for the reaction. As expected, the Ru-MoS2/MXene/S cathode-based cell exhibits a high-rate capability of 684.3 mAh g-1 at 6 C. After 1000 cycles, the Ru-MoS2/MXene/S cell maintains an excellent cycling stability of 696 mAh g-1 at 2 C with a capacity degradation as low as 0.02% per cycle. Despite a high sulfur loading of 9.5mg cm-2 and a lean electrolyte-to-sulfur ratio of 4.3, the cell achieves a high discharge capacity of 726 mAh g-1.