High Ammonia Concentrations Research Articles

Evaluating Ammonia Toxicity and Growth Kinetics of Four Different Microalgae Species.

Although wastewater with high ammonia concentration is an ideal alternative environment for microalgae cultivation, high ammonia concentrations are toxic to microalgae and inhibit microalgae growth. In this study, the ammonia responses of four widely used microalgae species were investigated. Chlorella vulgaris, Chlorella minutissima, Chlamydomonas reinhardtii and Arthrospira platensis were grown in batch reactors maintained at seven different NH4Cl concentrations at a constant pH of 8. Growth and nitrogen removal kinetics were monitored. IC50 values for the mentioned species were found as 34.82 mg-FA/L, 30.17 mg-FA/L, 27.2 mg-FA/L and 44.44 mg-FA/L, respectively, while specific growth rates for different ammonia concentrations ranged between 0.148 and 1.271 d-1. C. vulgaris demonstrated the highest biomass growth under an ammonia concentration of 1700.95 mg/L. The highest removal of nitrogen was observed for A. platensis with an efficiency of 99.1%. The results showed that all tested species could grow without inhibition in ammonia levels comparable to those found in municipal wastewater. Furthermore, it has been concluded that species C. vulgaris and A. platensis can tolerate high ammonia levels similar to those found in high strength wastewaters.

Optimization of direct-injection ammonia-diesel dual-fuel combustion under low load and higher ammonia energy ratios

Ammonia (NH3), as a potential zero-carbon fuel, has garnered significant attention for its application in compression ignition (CI) engines. Due to the low reactivity, ammonia is primarily used as dual fuel in CI engines. Therefore, the decarbonization potential is influenced by the ammonia energy ratio (AER). In this study, experimental research was conducted on expanding the AER at low load conditions in a direct-injection ammonia-diesel dual-fuel engine. The ammonia post-injection strategy was explored and significantly improved the suppression effect of high-concentration ammonia on diesel ignition, which could advance ignition timing and increase the peak heat release rate. As a result, coupled with intake heating, it expanded AER to 86 % at an indicated mean effective pressure (IMEP) of 4 bar. This strategy also increased the indicated thermal efficiency (ITE) by 8 % and significantly reduced unburned ammonia emissions. However, the combustion and emission performance was limited by the post-injection ammonia quantity and the injection timing of both diesel and ammonia, especially under high AER conditions.

Summer scour syndrome in weaned dairy calves: case series

BackgroundSummer scour syndrome (SSS) is a recently identified pathological condition affecting weaned dairy and dairy-beef calves during their first grazing season in Ireland. The syndrome is characterised by diarrhoea, weight loss, weakness, and can ultimately lead to death in some calves. Oral and oesophageal ulcerations are present in some cases. This study aimed to characterise a series of SSS cases in weaned dairy-bred calves on Irish commercial farms.ResultsFive farms with calves having unexplained diarrhoea at grass were referred by private veterinary practitioners (PVP) following preliminary testing to exclude coccidiosis and parasitic gastroenteritis. Farms were visited within 2 to 5 days following PVP’s referrals, or 2 days to 3 weeks relative to the onset of clinical signs. Farm management data, grass and concentrate samples, and biological samples from 46 calves (8 to 10 calves/farm) displaying clinical signs were collected. Two farms were subsequently found positive for coccidiosis and/or had chronic pneumonia problems after a thorough herd investigation and were designated as non-case farms (NCF). The remaining three farms were deemed typical SSS outbreaks (case farms; CF). Mean rumen fluid pH per farm ranged from 6.67 to 7.09 on CF, and 6.43–6.88 on NCF. Mean rumen fluid ammonia concentrations ranged from 17.6 to 29.6 mg/L and 17.2–45.0 mg/L on CF and NCF, respectively. Corresponding blood ammonia concentrations ranged from 129 to 223 µmol/L and 22–25 µmol/L. Mean blood copper and molybdenum concentrations were within normal range on all farms. Grass crude protein concentrations on the paddocks where the calves had grazed, and were currently grazing on the day of visit ranged from 137 to 148 g/kg DM and 106–177 g/kg DM, respectively on CF, and 160–200 g/kg DM and 151–186 g/kg DM, respectively on NCF. On CF, inorganic nitrogen fertiliser was applied 1 to 3 weeks pre-grazing, whereas on the two NCF, inorganic nitrogen fertiliser was applied 2 to 3 weeks pre-grazing on one farm and no fertiliser was applied on the other.ConclusionThese findings suggest that copper or molybdenum toxicity, and ruminal acidosis are not the primary causes of SSS. High blood ammonia concentrations and the timing and level of inorganic nitrogen fertiliser application to paddocks pre-grazing, warrant further investigation.

Increasing urine nitrification performance with sequential membrane aerated biofilm reactors

This study aimed to investigate whether separating organics depletion from nitrification increases the overall performance of urine nitrification. Separate organics depletion was facilitated with membrane aerated biofilm reactors (MABRs). The high pH and ammonia concentration in stored urine inhibited nitrification in the first stage and therewith allowed the separation of organics depletion from nitrification. An organics removal of 70 % was achieved at organic loading rates in the influent of 3.7 gCOD d−1 m−2. Organics depletion in a continuous flow stirred tank reactor (CSTR) for organics depletion led to ammonia stripping through diffused aeration of up to 13 %. Using an MABR, diffusion into the lumen amounted for 4 % ammonia loss only. In the MABR, headspace volume and therefore ammonia loss through the headspace was negligible. By aerating the downstream MABR for nitrification with the off-gas of the MABR for organics depletion, 96 % of the ammonia stripped in the first stage could be recovered in the second stage, so that the overall ammonia loss was negligibly low. Nitrification of the organics-depleted urine was studied in MABRs, CSTRs, and sequencing batch reactors in fed batch mode (FBRs), the latter two operated with suspended biomass. The experiments demonstrated that upstream organics depletion can double the nitrification rate. In a laboratory-scale MABR, nitrification rates were recorded of up to 830 mgNL−1 d−1 (3.1 gN m−2 d−1) with ambient air and over 1500 mgNL−1 d−1 (6.7 gN m−2 d−1) with oxygen-enriched air. Experiments with a laboratory-scale MABR showed that increasing operational parameters such as pH, recirculation flow, scouring frequency, and oxygen content increased the nitrification rate. The nitrification in the MABR was robust even at high pH setpoints of 6.9 and was robust against process failures arising from operational mistakes. The hydraulic retention time (HRT) required for nitrification was only 1 to 2 days. With the preceding organics depletion, the HRT for our system requires 2 to 3 days in total, whereas a combined activated sludge system requires 4 to 8 days. The N2O concentration in the off-gas increases with increasing nitrification rates; however, the N2O emission factor was 2.8 % on average and independent of nitrification rates. These results indicate that the MABR technology has a high potential for efficient and robust production of ammonium nitrate from source-separated urine.

Analisis Penyisihan Kandungan Amonia dengan Stripper di Pabrik Ammonia

Ammonia industrial waste treatment is part of the final process in the industry. Wastewater containing high ammonia content needs to be treated using a stripping process. This study to analysis the stripping process for ammonia waste treatment in the industry to obtain appropriate operating conditions and meet the wastewater standards issued by the Minister of the Environment. Data obtained during 10 days of operation were compared with the standards and analyzed for column efficiency. The results of the analysis showed that the waste output with a concentration of 13.9 - 49 ppm, a pH range of 8.7 - 9 and most of the waste discharge had met the standards, namely a maximum of 50 ppm and pH 6-9. The best gas-liquid ratio at the stripper inlet is 0.25 V / V and pressure has no significant effect on stripper efficiency.

Reforming of ammonia and ammonia-air mixtures in a homogenous plasma reactor: Parametric study of hydrogen yields

Plasma-assisted reforming shows great promise for making ammonia compatible with current engine technology, with minimal modifications required. This study examines the impact of various discharge, flow, and composition parameters on ammonia conversion into hydrogen using a new well-stirred homogeneous plasma reactor. Gas chromatography was used to measure hydrogen and oxygen, while ICCD imaging evaluated plasma homogeneity. Initial mixture composition significantly influences the response to plasma conditions. Relative to the initial ammonia composition, the conversion of pure ammonia yields a lower hydrogen percentage when compared to air-diluted mixtures. Introducing air changes the relationship between pulsed energy deposition and hydrogen production, resulting in a more substantial increase in conversion. Efficiency calculations demonstrate that high ammonia content and high pulse frequencies improve yields, while longer residence times in the reactor result in higher temperatures, also increasing yields. These findings provide insights into the underlying mechanisms of ammonia cracking and reforming in a discharge, and will serve to promote further investigation into plasma reforming strategies.

Flexible gas-strain dual sensor based on PU-supported Ti3C2Tx/CeO2/TiO2 yarns

The generation of high levels of ammonia in industries, agricultural sectors, and water treatment plants has triggered the necessity to detect high ammonia concentrations in a flexible way to ensure proactive measures for protecting humans and the environment. Therefore, it is essential to develop highly sensitive multifunctional sensors that have long-term stability, high durability, and a large stretch range. In our work, a novel approach was developed for fabricating flexible sensors consisting of polyurethane (PU) yarn and the loaded Ti3C2Tx/CeO2/TiO2 (abbreviated as MTCe) nanocomposites. The structures and morphology of the yarn-shaped sensors were analysed using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and other characterisation methods. In addition, gas and strain responses were recorded and analysed using an AES-4SD flexible electronic device. The response of the yarn-shaped sensors to 100 ppm NH3 was 42.9 % at room temperature (25 °C), indicating its excellent gas sensitivity. In addition, the sensors exhibited some key advantages, such as a large stretch range (60 %), high sensitivity (up to 385.285), and good durability (200 stretches/releases at 20 % stretch), which may be considered a remarkable achievement in the field of flexible sensor manufacturing for multiple applications.

Simultaneous removal of ammonium, phosphate, and phenol via self-assembled biochar composites CBCZrOFe3O4 and its utilization as soil acidity amelioration

ABSTRACT High concentrations of ammonium, phosphate, and phenol are recognized as water pollutants that contribute to the degradation of soil acidity. In contrast, small quantities of these nutrients are essential for soil nutrient cycling and plant growth. Here, we reported composite materials comprising biochar, chitosan, ZrO, and Fe3O4, which were employed to mitigate ammonium, phosphate, and phenol contamination in water and to lessen soil acidity. Batch adsorption experiments were conducted to assess the efficacy of the adsorbents. Initially, comparative studies on the simultaneous removal of NH4, PO4, and phenol using CB (biochar), CBC (biochar + chitosan), CBCZrO (biochar + chitosan + ZrO), and CBCZrOFe3O4 (biochar + chitosan + ZrO + Fe3O4) were conducted. The results discovered that CBCZrOFe3O4 exhibited the highest removal percentage among the adsorbents (P < 0.05). Adsorption data for CBCZrOFe3O4 were well fitted to the second-order kinetic and Freundlich isotherm models, with maximum adsorption capacities of 112.65 mg/g for NH4, 94.68 mg/g for PO4 and 112.63 mg/g for phenol. Subsequently, the effect of CBCZrOFe3O4-loaded NH4, PO4, and phenol (CBCZrOFe3O4-APP) on soil acidity was studied over a 60-day incubation period. The findings showed no significant changes (P < 0.05) in soil exchangeable acidity, H+, Mg, K, and Na. However, there was a substantial increase in the soil pH, EC, available P, CEC, N-NH4, and N-NO3. A significant reduction was also observed in the available soil exchangeable Al and Fe (P < 0.05). This technique demonstrated multi-functionality in remediating water pollutants and enhancing soil acidity.

Room temperature NH3 gas sensor based on In(OH)3/Ti3C2Tx nanocomposites.

Industrialization and agricultural demand have both improved human life and led to environmental contamination. Especially thedischarge of a lot of poisonous and harmful gases, including ammonia, ammonia pollution has become a pressing problem. High concentrations of ammonia can pose significant threats to both the environment and human health. Therefore, accurate monitoring and detection of ammonia gas are crucial. To address this challenge, we have developed an ammonia gas sensor using In(OH)3/Ti3C2Tx nanocomposites through an in-situ electrostatic self-assembly process. This sensor was thoroughly characterized using advanced techniques like XRD, XPS, BET, and TEM. In our tests, the I/M-2 sensor exhibited remarkable performance, achieving a 16.8% response to 100ppm NH3 at room temperature, which is a 3.5-fold improvement over the pure Ti3C2Tx MXene sensor. Moreover, it providesswift response time (20s), high response to low NH3concentrations (≤ 10ppm), and excellent long-term stability (30days). These exceptional characteristics indicate the immense potential of our In(OH)3/Ti3C2Tx gas sensor in ammonia detection.

Enhancing Rubber Industry Wastewater Treatment through an Integrated AnMBR and A/O MBR System: Performance, Membrane Fouling Analysis, and Microbial Community Evolution.

This study explores the effectiveness of an integrated anaerobic membrane bioreactor (AnMBR) coupled with an anoxic/oxic membrane bioreactor (A/O MBR) for the treatment of natural rubber industry wastewater with high sulfate, ammonia, and complex organic contents. This study was conducted at the lab-scale over a duration of 225 days to thoroughly investigate the efficiency and sustainability of the proposed treatment method. With a hydraulic retention time of 6 days for the total system, COD reductions were over 98%, which reduced the influent from 22,158 ± 2859 mg/L to 118 ± 74 mg/L of the effluent. The system demonstrates average NH3-N, TN, and total phosphorus (TP) removal efficiencies of 72.9 ± 5.7, 72.8 ± 5.6, and 71.3 ± 9.9, respectively. Despite an average whole biological system removal of 50.6%, the anaerobic reactor eliminated 44.9% of the raw WW sulfate. Analyses of membrane fouling revealed that organic fouling was more pronounced in the anaerobic membrane, whereas aerobic membrane fouling displayed varied profiles due to differential microbial and oxidative activities. Key bacterial genera, such as Desulfobacterota in the anaerobic stage and nitrifiers in the aerobic stage, are identified as instrumental in the biological processes. The microbial profile reveals a shift from methanogenesis to sulfide-driven autotrophic denitrification and sulfammox, with evidence of an active denitrification pathway in anaerobic/anoxic conditions. The system showcases its potential for industrial application, underpinning environmental sustainability through improved wastewater management.

Characteristics of late summer Arctic brash sea ice and its melting effect on the surface-water biogeochemistry of the Chukchi Shelf and Canada Basin

To understand the impact of the melting of late summer Arctic brash ice on the surface waters of the Chukchi Sea, we collected sea-ice samples during 2021. Floating sea ice was collected by a wire mesh pallet cage from the side of the R/V Mirai. We measured physical and biogeochemical parameters such as salinity, oxygen stable isotopic ratios, turbidity, and concentrations of chlorophyll-a and nutrients. The samples of brash ice were multiyear ice based on satellite back-trajectory analysis. Comparison of nutrient concentrations in brash ice with those of seawater samples from the temperature minimum layer similar to the water in the sea ice originated suggested that the characteristics of the brash ice were greatly affected by biogeochemical processes such as remineralization. The extremely high turbidity and concentrations of chlorophyll-a observed in the brown/green ice samples reflected the impact of sediment as well as the influence of biological activities. The N:P ratios were less than 1 because of the high phosphate concentrations, even though the ammonium concentrations were high. We hypothesized that this low N:P ratio reflected the combined effects of the accumulation of nutrients due to remineralization in the biofilm and differences of remineralization rate and adsorption features of nitrogen and phosphorus. Based on the high nitrate and ammonium concentrations in the sea-ice samples, we postulated a marked impact of sea-ice meltwater on the nitrogen cycle in the nitrate-depleted surface waters of the Chukchi Sea during late summer. We estimated that meltwater nitrogen could support 0.3%–2.6% of primary production in the northern Chukchi Sea. Our results suggest that high-turbidity ice will play an important role as a source of nutrients to the ocean during melting of sea ice, and understanding its distribution, amount, and geochemical characteristics is vital.

High Ammonia Nitrogen-Induced Reproductive Toxicity in Goldfish (Carassius auratus) Mature Ovary

Ammonia nitrogen is one of the major pollutants in aquaculture. However, the mechanism of ammonia stress on ovarian development and follicular atresia is unknown. In this study, goldfish (Carassius auratus) were exposed to different ammonia concentrations, including 0 (control, C) and 50 mg/L (high, H) for 48 hr at 21 ± 0.5°C. Histology of the ovarian tissue sections revealed that the high ammonia concentrations inhibited the maturation of oocytes, and induced broken and wrinkled radiation bands, follicular membranes, and the accumulation of rod-shaped yolk particles. From the transcriptome data, a total of 1,405 differentially expressed genes (DEGs) were detected between H and C groups. Most DEGs were highly enriched in low-density lipoprotein particle-mediated signaling, oxidative stress-induced premature senescence, and ovarian steroidogenesis pathway. Furthermore, a total of 19 genes were selected and determined by quantitative real-time polymerase chain reaction (qRT-PCR). The changes in oxidative stress and antioxidant activity indicated the excessive accumulation of reactive oxygen species (ROS) in ovarian tissue. The ovarian apoptosis was induced in the H group. The downregulation of genes involved in the ovarian steroidogenesis pathway indicated that ammonia nitrogen stress prevented the synthesis of sexual hormones. These results suggest that high-concentration ammonia stress induces ovarian damage in goldfish, affecting its antioxidant function, leading to excessive ROS accumulation, ovarian apoptosis, and hindered steroid synthesis, adversely affecting reproductive performance.

Pt/Al2O3@Ce/ZrO2-S bifunctional catalysts prepared by mechanically milling for selective catalytic oxidation of high-concentration ammonia.

The selective catalytic oxidation (SCO) is an effective method for removing slipped high-concentration ammonia from NH3-fueled engine exhaust gas. Herein a novel bifunctional catalyst was synthesized by mechanically mixing sulfated Ce/ZrO2 (Ce/ZrO2-S) with a small fraction of Pt/Al2O3 (Pt 0.1 wt.%) for SCO of NH3. As expected, the introduction of a small amount of Pt/Al2O3 significantly improved NH3 conversion ability of Ce/ZrO2-S catalysts toward low-temperature direction. When the mass ratio of Pt/Al2O3 to Ce/ZrO2-S was 7.5% (the corresponding mixed catalyst was denoted as P@CZS-7.5), T90 temperature was 312°C. More importantly, P@CZS-7.5 catalyst exhibited a much better N2 selectivity (> 96%) in a wide temperature range (320 ~ 450°C). H2-TPR results revealed that the addition of a trace amount of Pt/Al2O3 significantly led to a distinct shift of reduction temperature peak toward low-temperature direction, thereby greatly improved the low-temperature redox performance of mixed catalysts. Furthermore, NH3-TPD and BET results showed that P@CZS-7.5 catalyst exhibited a similar NH3 adsorption capacity to Ce/ZrO2-S catalyst, while the former had a relatively higher specific surface area than the latter. It was considered as a crucial factor for P@CZS-7.5 catalyst maintaining superior N2 selectivity in high-concentration NH3 (5000ppm) removal processes. In situ DRIFTS results indicated that P@CZS-7.5 catalyst followed the internal selective catalytic reduction (i-SCR) mechanism in NH3-SCO reactions.

A Higher Stomatal Aperture is Associated with the Growth Promotion of Centipedegrass (Eremochloa ophiuroides (Munro) Hack.) Under High Concentrations of Ammonium

A Higher Stomatal Aperture is Associated with the Growth Promotion of Centipedegrass (Eremochloa ophiuroides (Munro) Hack.) Under High Concentrations of Ammonium

Nitrification inhibitor chlorate and nitrogen substrates differentially affect comammox Nitrospira in a grassland soil.

Through the combined use of two nitrification inhibitors, Dicyandiamide (DCD) and chlorate with nitrogen amendment, this study aimed to investigate the contribution of comammox Nitrospira clade B, ammonia oxidizing bacteria (AOB) and archaea (AOA) to nitrification in a high fertility grassland soil, in a 90-day incubation study. The soil was treated with nitrogen (N) at three levels: 0 mg-N kg-1 soil, 50 mg-N kg-1 soil, and 700 mg-N kg-1 soil, with or without the two nitrification inhibitors. The abundance of comammox Nitrospira, AOA, AOB, and nitrite oxidising bacteria (NOB) was measured using qPCR. The comammox Nitrospira community structure was assessed using Illumina sequencing. The results showed that the application of chlorate inhibited the oxidation of both NH4+ and NO2- in all three nitrogen treatments. The application of chlorate significantly reduced the abundance of comammox Nitrospira amoA and nxrB genes across the 90-day experimental period. Chlorate also had a significant effect on the beta diversity (Bray-Curtis dissimilarity) of the comammox Nitrospira clade B community. Whilst AOB grew in response to the N substrate additions and were inhibited by both inhibitors, AOA showed litle or no response to either the N substrate or inhibitor treatments. In contrast, comammox Nitrospira clade B were inhibited by the high ammonium concentrations released from the urine substrates. These results demonstrate the differential and niche responses of the three ammonia oxidising communities to N substrate additions and nitrification inhibitor treatments. Further research is needed to investigate the specificity of the two inhibitors on the different ammonia oxidising communities.

Integrated partial nitrification and Tribonema minus cultivation for cost-effective ammonia recovery and lipid production from slaughterhouse wastewater

High ammonium content in untreated anaerobic digestion (AD) wastewater can inhibit microalgal growth, hindering both bioremediation and biomass/lipid productivity. This study investigated the potential of partial nitrification (PN) as a pretreatment step for AD effluent before cultivating the oleaginous microalga Tribonema minus for bioremediation and lipid production. The PN process transforms inhibitory ammonium into nitrate, a nitrogen form that microalgae can effectively utilize, thereby reducing ammonia toxicity. The results showed remarkable resilience in T. minus, with the species being able to tolerate high ammonium levels (≤120 mg/L) when combined with nitrate in synthetic wastewater. However, when ammonium was the sole nitrogen source (>30 mg/L), its inhibitory effect on T. minus growth became evident. Nevertheless, successful cultivation of T. minus was achieved in PN effluent from slaughterhouse AD using a Sequencing Batch Reactor (SBR) (25 °C and hydraulic retention time (HRT) of 1.5 h) containing 190 mg/L ammonium, achieving 51.25 % lipid accumulation. Additionally, cultivation with 125 mg/L NH4+-N in the PN effluent resulted in removal rates exceeding 95 % for NH4+-N. This approach, therefore, delivered the dual advantage of not only mitigating the environmental risks associated with wastewater but also fostering renewable biomass production for cleaner energy.

Water Quality Assessment Using the Water Quality Index, and Geographic Information Systems in Nador Canal, Morocco

In recent decades, water pollution has emerged as a significant concern, posing a threat to both humans and natural ecosystems. This study aimed to assess the spatial variations in water quality in the Nador Canal, Morocco using the water quality index combined with multivariate statistical techniques and geographic information systems (GIS). The parameters examined were then compared to the maximum permissible limit values recommended by Moroccan surface water standards and the World Health Organization. The results indicated that the WQI of Nador Canal is generally suitable for irrigation and unsuitable for drinking. It indicated that the quality of surface water in the Nador Canal is affected by organic pollutants, and this is evidenced by low levels of dissolved oxygen, the levels of elements were high, especially chlorine and sodium, in addition to a high concentration of ammonia, nitrate, and phosphate in some of the stations studied. Principal component analysis (PCA) results revealed that PC1–PC3 collectively accounted for 73% of the variation in surface water quality within the study area. The cluster analysis also proves that the water quality is relatively polluted. Potential contributing factors to surface water pollution include changes in the hydrological regime, household waste discharges, and agricultural activities. These findings furnish essential insights into water quality, particularly its suitability for irrigation, and contribute to enhancing the water quality management system of the Nador Canal in the Gharb region of Morocco.

Microalgae cultivation trials in a membrane bioreactor operated in heterotrophic, mixotrophic, and phototrophic modes using ammonium-rich wastewater: The study of fouling.

In this work, microalgae cultivation trials were carried out in a membrane bioreactor to investigate fouling when the cultures of Chlorellavulgaris were grown under mixotrophic, heterotrophic, and phototrophic cultivation regimes. The Chlorella cultures were cultivated in wastewater as a source of nutrients that contained a high concentration of ammonium. In mixotrophic cultivation trials, the results showed that the elevated contents of carbohydrates in the soluble microbial product and proteins in extracellular polymeric substances probably initiated membrane fouling. In this case, the highest protein content was also found in extracellular polymeric substances due to the high nitrogen removal rate. Consequently, transmembrane pressure significantly increased compared to the phototrophic and heterotrophic regimes. The data indicated that cake resistance was the main cause of fouling in all cultivations. Higher protein content in the cake layer made the membrane surface more hydrophobic, while carbohydrates had the opposite effect. Compared to a mixotrophic culture, a phototrophic culture had a larger cell size and higher hydrophobicity, leading to less membrane fouling. Based on our previous data, the highest ammonia removal rate was reached in the mixotrophic cultures; nevertheless, membrane fouling appeared to be the fundamental problem.

Discovery of the first hydrothermal field along the 500-km-long Knipovich Ridge offshore Svalbard (the Jøtul field)

Oceanic spreading centers north of Iceland are characterized by ultraslow spreading rates, and related hydrothermal activity has been detected in the water column and at the seafloor along nearly all ridge segments. An exception is the 500-km-long Knipovich Ridge, from where, until now, no hydrothermal vents were known. Here we report the investigation of the first hydrothermal vent field of the Knipovich Ridge, which was discovered in July 2022 during expedition MSM109. The newly discovered hydrothermal field, named Jøtul hydrothermal field, is associated with the eastern bounding fault of the rift valley rather than with an axial volcanic ridge. Guided by physico-chemical anomalies in the water column, ROV investigations on the seafloor showed a wide variety of fluid escape sites, inactive and active mounds with abundant hydrothermal precipitates, and chemosynthetic organisms. Fluids with temperatures between 8 and 316 °C as well as precipitates were sampled at four vent sites. High methane, carbon dioxide, and ammonium concentrations, as well as high 87Sr/86Sr isotope ratios of the vent fluids indicate strong interaction between magma and sediments from the Svalbard continental margin. Such interactions are important for carbon mobilization at the seafloor and the carbon cycle in the ocean.

Ammonia-enriched biogas as an alternative fuel in diesel engines: Combustion, performance and emission analysis

This study investigates the potential of ammonia as a secondary fuel in diesel engines, amidst the rising interest in alternative fuels and the growth of electric vehicles. Unlike hydrogen, with its higher flammability and safety concerns, ammonia offers a viable, sustainable fuel source. A single-cylinder diesel engine was utilized to assess engine performance and combustion characteristics using ammonia gaseous blends. Ammonia was combined with biogas to mitigate its corrosive effects and compensate for its lower heating value. Th entire best conducted with constant ammonia flow rate of 30 LPM. Diesel was mixed with biogas in compositions of 10 LPM, 20 LPM and 30 LPM, and tested under engine loads of 25%, 50%, 75%, and 100%. The blend with the highest ammonia concentration (B30B3) exhibited the largest heat release rate, highlighting a strong correlation between ammonia content and heat release levels. This is attributed to the premixed combustion phase and the accelerated flame speed associated with ammonia. An increase in ammonia content resulted in higher brake thermal efficiency and reduced brake specific fuel consumption. All ammonia-inclusive blends showed a decrease in hydrocarbon and carbon monoxide emissions, with the lowest emissions observed in the B30B3 blend. However, the high flammability of biogas in the B30B3 blend, compared to diesel, and enhanced fuel atomization, led to increased nitrogen Oxides formation. The results clearly indicate that combination of ammonia along with the biogas enhances the combustion and reduces greenhouse gas emissions. Findings of this study provides valuable insights into the use of ammonia as a sustainable alternative in diesel engines, offering a improved balance between combustion efficiency and environmental impact.