Heterologous Bone Graft Research Articles

Socket shield technique: Stress distribution analysis.

To analyze through finite element analysis the stress distribution in peri-implant bone tissues, implants, and prosthetic components induced by the socket shield (SS) technique in comparison to other techniques used to treat tooth loss. A three-dimensional model of a superior central incisor crown supported by implant was modeled and three different placement conditions were simulated: SS - 2.0-mm-thick root dentin fragment positioned between the alveolar buccal wall and implant; heterologous bone graft (HBG) - bovine bone graft positioned the alveolar buccal wall and implant; and control (C) - implant fully placed in bone tissue of a healed alveolus. The model was restricted at the lateral surfaces of the bone tissue and the following loads were simulated: Both oblique (45°) loads of 100 N on the lingual surface of the crown (maximal habitual intercuspation) and 25.5 N on the incisal edge of the crown (tooth contact during mandibular protrusion) were simultaneously applied. Tensile stress, shear stress, compression, and displacement were analyzed in the cortical bone, trabecular bone, dentin root fragment, and bone graft; while equivalent von Mises stresses were quantified in the implant and prosthetic components. Stress values of SS and HBG in the bone tissues were higher than C, while slight differences within models were observed for dentin root fragment, bone graft, implant, and prosthetic components. The SS technique presented the highest stress concentration in the peri-implant tissues.

Autologous tooth for bone regeneration: dimensional examination of Tooth Transformer® granules.

Since 1967, when the osteoinduction properties of autogenous demineralized dentin matrix were discovered, autologous tooth grafts have been advocated as a viable option to autologous or heterologous bone graft. Tooth graft materials may be extracted from the patient's whole tooth using a granulating device. The aim of this study was to examine the size of granules obtained by the Tooth Transformer (TT)® device, using a laser instrument with high precision. The TT® device can obtain bone graft material in a short period from an extracted tooth. The resulting material can act as an osteoconductive scaffold, providing a mineral substrate during resorption, including platelet growth factors and morphogenetic proteins. Different studies have investigated the dimension and behavior of various graft material particles, since the size of the grafted particles may play a role in osteogenesis and bone regeneration. Different dimensions of granules are available: small (< 400 µm), medium (400 µm-1,000 µm) and large (1,000 µm-2,000 µm). From 4.03 µm to 100 µm the percentage of granules was 14.52 ± 1.93%. A larger part of the granules was up to 100 µm, while 85.47 ± 1.93% of the granules were from 100 µm to 1,000 µm. 85% of the granules produced were in accordance with the dimensions suggested in the literature.

Mechanical behaviour of cancellous bone tissues used for the manufacturing of heterologous bone grafts

In this work, the mechanical behaviour of cancellous bone tissues used for the manufacturing of commercial heterologous bone grafts was investigated both at small and at large strains. Three different tissues were examined. They were obtained from equine bones after a specific proprietary enzymatic-based treatment aimed at achieving perfect biocompatibility while preserving the collagenous part. Two tissues had the mineral content of the bones of origin (femur, humerus), whereas the third was markedly demineralized (femur). The response at small strains and at failure was studied by means of monotonic compression tests in quasi-static conditions. Stiffness and strength turned out to be governed by the apparent density of the tissue, with specimen size and geometry, and tissue macro-structural characteristics, only playing a secondary role. A ductile- and a brittle-like failure was exhibited by the demineralized tissue and the non-demineralized ones, respectively. The large deformation behaviour was studied by means of cyclic compression tests, which clearly highlighted the occurrence of plasticity (for strains higher than ≈1.9%), and allowed to study the strain accumulation processes, at the macromechanical level. More in-depth microstructural analyses were carried out on the demineralized tissue. Flexural tests were also performed.

Mechanical Behaviour of Cancellous Bone Tissues Used for the Manufacturing of Heterologous Bone Grafts

Mechanical Behaviour of Cancellous Bone Tissues Used for the Manufacturing of Heterologous Bone Grafts

A Retrospective Analysis of Treatment Outcomes Following Guided Bone Regeneration at Sites Exhibiting Severe Alveolar Ridge Atrophy.

Severely atrophic alveolar ridges represent a great challenge for implant-prosthetic rehabilitations. The aim of this study was to clinically and histologically evaluate horizontal and vertical bone gain, as well as implant survival/success rate after guided bone regeneration (GBR) for the reconstruction of large bone defects. Fourteen subjects (7 males and 7 females; mean age: 48.9 ± 14.1) were enrolled in the study. They were selected according to specific inclusion criteria and all patients required GBR procedures for placing implants in severe atrophic jaws (bone height ≤6 mm). Guided bone regeneration was performed using dense polytetrafluoroethylene nonresorbable titanium-reinforced membranes associated with particulate heterologous bone grafts. Implant placement was performed 6 months after surgery at the same time as the removal of the membrane. Furthermore, a biopsy sample from the grafted sites was collected to conduct a histological analysis of the regenerated bone. Forty-seven dental implants were placed and followed up after prosthetic loading. Seventeen sites, 8 in the maxilla and 9 in the mandible, were suitable for the GBR procedure. The healing period was uneventful in 13 sites. The average value of vertical bone regeneration was 5.88 ± 1.17 mm. Postloading follow-up ranged from 24 to 59 months. During the follow-up, clinical and radiographic exams showed no significant bone resorption and, in each case, the criteria for implants' survival were respected with no signs of any complications. Histological analysis of the bone biopsy samples revealed residual graft particulate in close contact with newly formed bone. Guided bone regeneration is a reliable technique for reconstruction of severe atrophic ridges. Larger long-term follow-up studies are needed to evaluate the condition of the bone grafted over time and its ability to support functional loading of the implants.

A Minimally Invasive Technique for Short Spiral Implant Insertion with Contextual Crestal Sinus Lifting in the Atrophic Maxilla: A Preliminary Report.

The most recently reported techniques for the rehabilitation of the atrophic posterior maxilla are increasingly less invasive, as they are generally oriented to avoid sinus floor elevation with lateral access. The authors describe a mini-invasive surgical technique for short spiral implant insertion for the prosthetic rehabilitation of the atrophic posterior maxilla, which could be considered a combination of several previously described techniques based on the under-preparation of the implant site to improve fixture primary stability and crestal approach to the sinus floor elevation without heterologous bone graft. Eighty short spiral implants were inserted in the molar area of the maxilla in patients with 4.5–6 mm of alveolar bone, measured on pre-operative computed tomography. The surgical technique involved careful drilling for the preparation of implant sites at differentiated depths, allowing bone dislocation in the apical direction, traumatic crestal sinus membrane elevation, and insertion of an implant (with spiral morphology) longer than pre-operative measurements. Prostheses were all single crowns. In all cases, a spiral implant 2–4 mm longer than the residual bone was placed. Only two implants were lost due to peri-implantitis but subsequently replaced and followed-up. Bone loss values around the implants after three months (at the re-opening) ranged from 0 to 0.6 mm, (median value: 0.1 mm), while after two years, the same values ranged from 0.4 to 1.3 mm (median value: 0.7 mm). Clinical post-operative complications did not occur. After ten years, no implant has been lost. Overall, the described protocol seems to show good results in terms of predictability and patient compliance.

Evaluation of New Octacalcium Phosphate-Coated Xenograft in Rats Calvarial Defect Model on Bone Regeneration

Bone graft material is essential for satisfactory and sufficient bone growth which leads to a successful implant procedure. It is classified into autogenous bone, allobone, xenobone and alloplastic materials. Among them, it has been reported that heterogeneous bone graft material has a porous microstructure that increases blood vessels and bone formation, and shows faster bone formation than other types of bone graft materials. We observed new bone tissue formation and bone remodeling using Ti-oss® (Chiyewon Co., Ltd., Guri, Korea), a heterologous bone graft material. Using a Sprague–Dawley rat calvarial defect model to evaluate the bone healing effect of biomaterials, the efficacy of the newly developed xenograft Ti-oss® and Bio-Oss® (Geistilch Pharma AG, Wolhusen, Switzerland). The experimental animals were sacrificed at 8 and 12 weeks after surgery for each group and the experimental site was extracted. The average new bone area for the Ti-oss® experimental group at 8 weeks was 17.6%. The remaining graft material was 22.7% for the experimental group. The average new bone area for the Ti-oss® group was 24.3% at 12 weeks. The remaining graft material was 22.8% for the experimental group. It can be evaluated that the new bone-forming ability of Ti-oss® with octacalcium phosphate (OCP) has the bone-forming ability corresponding to the conventional products.

Secondary Rhinoplasty in Binder Syndrome: Considerations and Management of Complex Problem With Heterologous Bone Graft.

Binder Syndrome occurs in less than 1 per 10,000 live births. Mean features of the syndrome include arhinoid face, abnormal position of the nasal bones, intermaxillary hypoplasia with associated malocclusion, reduced or absent anterior nasal spine, atrophy of the nasal mucosa and absence of the frontal sinus. Treatment of these facial deformities is obviously surgical. In the present work, the authors describe, step by step, their technique in secondary rhinoplasty in a 36-years-old patient affected by Binder Syndrome. In this case, the authors used autologous cartilage graft and heterologous bone graft.Satisfying results are achieved in 12 months of follow-up: graft resorption is acceptable, position of the graft is stable, the authors have no signs of infection and the patient is satisfied with the aesthetical and functional results. The authors believe that the first option, in complex nose's reconstruction, is the use of autologous grafts but, the use of cartilage heterologous bone graft should be taken in account, in the future, as a secondary option in Binder Syndrome and in malformed patients.

Mid-term CT assessment of bone healing after nanohydroxyapatite augmentation in open-wedge high tibial osteotomy

BackgroundThe aim of the present study was to confirm the effectiveness of adding nanohydroxyapatite (NHA) to a heterologous bone graft in open-wedge high tibial osteotomy (OWHTO) by measuring the bone density via multislice computed tomography (CT) of the tibial osteotomy gap in a mid-term follow-up (five years). MethodsTwenty-six patients undergoing OWHTO were randomly assigned to two groups: a pure graft group (Group A), in which the osteotomy gap was filled with only heterologous bone graft, and an NHA group (Group B), in which the osteotomy gap was filled with heterologous bone graft and NHA. CT was performed within one week of the operation, after two months, after 12 months and after five years. CT volume acquired in Hounsfield units (HU) was measured on three planes. ResultsThe normal bone density was 110.2 ± 11.7 HU. The value of mean density at five years in Group A was 296.8 ± 81.8 HU, while in Group B, it was 202.2 ± 45.1 HU, showing a density more similar to normal bone and greater bone uniformity inside the osteotomy. The difference between the two groups was statistically significant (p < 0.05). Furthermore, both groups showed excellent mid-term clinical outcomes without significant differences. ConclusionsThis study revealed that absorbability and bone formation at the osteotomy site in the NHA group was significantly higher as compared with the pure graft group at five years postoperatively.

Synergistic Effects on Incorporation of β-Tricalcium Phosphate and Graphene Oxide Nanoparticles to Silk Fibroin/Soy Protein Isolate Scaffolds for Bone Tissue Engineering.

In bone tissue engineering, an ideal scaffold is required to have favorable physical, chemical (or physicochemical), and biological (or biochemical) properties to promote osteogenesis. Although silk fibroin (SF) and/or soy protein isolate (SPI) scaffolds have been widely used as an alternative to autologous and heterologous bone grafts, the poor mechanical property and insufficient osteoinductive capability has become an obstacle for their in vivo applications. Herein, β-tricalcium phosphate (β-TCP) and graphene oxide (GO) nanoparticles are incorporated into SF/SPI scaffolds simultaneously or individually. Physical and chemical properties of these composite scaffolds are evaluated using field emission scanning electron microscope (FESEM), X-ray diffraction (XRD) and attenuated total reflectance Fourier transformed infrared spectroscopy (ATR-FTIR). Biocompatibility and osteogenesis of the composite scaffolds are evaluated using bone marrow mesenchymal stem cells (BMSCs). All the composite scaffolds have a complex porous structure with proper pore sizes and porosities. Physicochemical properties of the scaffolds can be significantly increased through the incorporation of β-TCP and GO nanoparticles. Alkaline phosphatase activity (ALP) and osteogenesis-related gene expression of the BMSCs are significantly enhanced in the presence of β-TCP and GO nanoparticles. Especially, β-TCP and GO nanoparticles have a synergistic effect on promoting osteogenesis. These results suggest that the β-TCP and GO enhanced SF/SPI scaffolds are promising candidates for bone tissue regeneration.

Minimal Invasive Flapless Piezotome Alveolar Crest Horizontal Split Technique: Preliminary Results

Alveolar split crest is an established surgical technique to enable implant insertion into narrow and atrophic alveolar crest. This surgical technique is adopted to position standard or large implants so that postextractive anatomy compromises with this attempt. The aim of this study was to evaluate the horizontal alveolar bone augmentation and its stability along time with a minimally invasive flapless technique. Twenty-four implants were inserted in 10 patients during a 15-month period. Clinical parameters such as horizontal bone augmentation, intrasurgical complications, patient morbidity, implant loss, and vertical bone loss (VBL) were recorded in the first 3 years after surgery. Using cone-beam computed tomography (CBCT), alveolar bone width was measured for both implants position and bone reconstructions. 6 months later, at the time of implant integration, a new low-dose CBCT was performed. Implant survival (IS) and VBL were evaluated radiographically for 3 years. The initial bone thickness measured on the ridge is between 0.82 mm and 5.40 mm (average 2.43 mm), after the split crest the bone width is between 4.65 mm and 8.09 mm (average 6.39 mm). This leads to an increase in the alveolar bone width of between 0.80 mm and 6.01 mm (average 3.71 mm) on the ridge. No implant was lost at 3 years, and all implants are stable at the end of the study. Three years after the surgery, controls showed a VBL of between 0.0 mm and 1.2 mm (average 0.63 mm) around the inserted implants. These parameters suggest using a flapless technique to reduce bone resorption around the implant neck. A minimally invasive approach allows to reduce the surgical trauma and postsurgical discomfort. The complete vascular supply is maintained, the bone resorption is reduced, and the connective epithelium does not undergo postsurgical retraction, achieving the full maintenance of the residual keratinized gingiva. A technique such as split crest can be a valid option to avoid autologous or heterologous bone grafts.

Giant Cell Tumour of the First Cuneiform: Case Study

Giant cell tumours (GCT) are usually benign, locally aggressive tumours. They tend to occur in long bones and rarely in small bones, with an incidence rate of 1.2 to 2.4% in the bones of the foot. The objective is to present a unique case in the literature of a GCT that only affected the first cuneiform. We present the case of a 35-year-old male patient seen at Hospital General de México (HGM) with seven months history of pain and increased volume in the medial region of the right foot, with X-ray and MRI images consistent with GCT in first cuneiform of the right foot. The excisional biopsy confirmed GCT. The definitive treatment consisted of curettage, cryotherapy with nitrogen and heterologous bone graft placement. Evolution was satisfactory, with no pain, no volume increase, normal gait and radiographic bone graft integration. Follow-up was at six years.

Osseous Remodeling Technique of the Sella Turcica: A New Surgical Option for Primary Empty Sella Syndrome

Empty sella is an anatomic finding that is usually asymptomatic. However, when patients with empty sella finding present with visual deficits, surgical treatment may be necessary. The main goal of surgery is to elevate sellar content through a transsphenoidal approach. The aim of this study was to demonstrate a new technique for precise reconstruction of the sellar floor using a heterologous bone block to restore the anatomic elements of the sella turcica. Three patients with primary empty sella who presented with visual field defects were prospectively included. Surgery was performed through a microsurgical transsphenoidal approach and involved elevating the sellar content by using a tricortical heterologous bone graft, the dimensions of which were obtained considering the exact dimensions of each patient's sella turcica. The graft was premodeled outside the surgical bed and carefully introduced into the sella turcica to achieve the required elevation (chiasmapexy). Vision of all 3 patients improved, and the improvement persisted throughout the follow-up period. 2 patients, this improvement was noted immediately after surgery, and in the third patient, this change in vision occurred 1 week later. Long-term imaging studies showed the persistence of the bone graft in the sella turcica and the exact elevation of the sellar content at the end of the follow-up period. There were no complications in the present series. The technique presented here is simple and reproducible and allows an almost exact and persistent elevation of the sellar content.

A New Tooth Processing Apparatus Allowing to Obtain Dentin Grafts for Bone Augmentation: The Tooth Transformer

Introduction:Human dentin matrix could be considered an excellent alternative to autologous or heterologous bone graft. Autologous tooth graft has been proposed since 1967 when the osteoinduction properties of autogenous demineralized dentin matrix were discovered.Methods:The preparation technique to transform autologous teeth in suitable grafting material still represents the fundamental step of the whole procedure.Aim:The aim of the present study was to test an innovative medical device that could obtain tooth graft materials starting from the whole tooth of the patient. 15 consecutive cases of tooth grafting procedures were performed with a mean follow up period of 18 months.Results:In all cases, after 6 months of healing, the defects were almost completely filled by newly formed hard tissue. The new tissue was examined after 6 months, both from a radiological point of view by CBCT scans and from a clinical observation. It showed a compactness similar to the medium-density bone. No signs of inflammations were observed. No infective complications were recorded during the post-operative healing. No graft particles or grains were visible in the regenerated bone structure that appeared homogeneous and uniform.Discussion:The results of the present study showed favorable bony healing in guided regenerative surgery procedures using autologous tooth graft. Future studies with long follow up period are needed in order to better evaluate the potential of demineralized dentin autografts.

Preservation of Dental Sockets Filled with Composite Bovine Bone. A Single-Blind Randomized Clinical Trial.

The purpose of this study was to evaluate the preservation of alveolar dimensions in human fresh extraction sockets filled with a composite bovine bone graft by means of design of single-blind randomized clinical trial. Forty participants had monoradicular teeth extracted (one teeth in each participant), and after were randomly divided into 2 groups: individuals whose fresh sockets were filled with the composite heterologous bone graft (Biomaterial Group), or with blood clot (Control Group). After extraction, the fresh sockets were measured at their greatest mesiodistal (MD) and bucco-lingual/palatal (BL/P) distance. Primary closure of the soft tissue was performed with a fibro-mucosal plug. After 120 post-operative days, the re-entry procedure was performed and the largest MD and BL/P measurements were again obtained to calculate the remodeling of the alveolar bone measured in percentage. In the biomaterial group, a percentage reduction of 1.62% and 3.29% in the MD and BL/P dimensions was observed 120 days after the extractions, whereas a reduction of 4.97% and 7.18% in the MD and BL/P dimensions occurred in the control group. There was a statistically significant difference (p<0.05) between the two groups for the bucco-palatal and mesiodistal measurements in the maxilla. In view of the results obtained, it can be concluded that composite bovine bone graft limited but did not impede alveolar bone remodeling.

Predicting the failure in distal femur fractures

IntroductionThe incidence of nonunion after fractures of the distal femur is up to 6%. The distal femoral nonunion is a disabling disease that needs complex steps in his treatment. Aim of our study is to find predicting factors of non-unions. Materials and methodsWe retrospectively analyzed 116 cases of distal femoral fractures and 20 cases of non-unions. In both surgeries we analyzed: accuracy of reduction, stability of fixation, hardware used, residual medial or lateral bone defect, use of autologous or heterologous bone grafts. ResultsMalreduction, particularly axial defect, associated with unbalanced fixation, and a medial cortical bone defect of greater or lesser extent were found to be the major risk factors of nonunion. Addressing both the mechanical and the biological environment was associated with successful non union treatment. ConclusionThe main principles for solving a distal femoral nonunion are new better reduction, correction of the medial bone defect and biological support with bone grafting. From the mechanical side the association of a medial strut graft or a medial column plate could be very useful in the treatment of these non-unions.

Polyurethane foam/nano hydroxyapatite composite as a suitable scaffold for bone tissue regeneration

In bone tissue regeneration, the use of biomineralized scaffolds to create the 3D porous structure needed for well-fitting with defect size and appropriate cell interactions, is a promising alternative to autologous and heterologous bone grafts. Biomineralized polyurethane (PU) foams are here investigated as scaffold for bone tissue regeneration. Biomineralization of the foams was carried out by activation of PU surface by a two steps procedure performed for different times (1 to 4 weeks). Scaffolds were investigated for morphological, chemico-physical and mechanical properties, as well as for in vitro interaction with rat Bone Marrow Mesenchymal Stem Cells (BMSCs). Untreated and biomineralized PU samples showed a homogenous morphology and regular pore size (average Ø=407μm). Phase and structure of formed calcium phosphates (CaPs) layer onto the PU foam were analyzed by Fourier Transform Infrared spectroscopy and X-ray diffraction, proving the formation of bone-like nano hydroxyapatite. Biomineralization caused a significant increase of mechanical properties of treated foams compared to untreated ones. Biomineralization also affected the PU scaffold cytocompatibility providing a more appropriate surface for cell attachment and proliferation. Considering the obtained results, the proposed scaffold can be considered suitable for bone tissue regeneration.

Evaluation of hyaluronic matrix efficacy in sinus augmentation: a randomized-controlled histomorphometric and micro–computed tomography analysis

The objective of the present study was to test the hypothesis that the addition of hyaluronic acid–based matrix to collagenated heterologous bone graft for sinus augmentation would enhance bone formation compared to collagenated heterologous bone graft alone in the early healing period, by micro−computed tomography and histomorphometry. Thirteen systemically healthy patients requiring bilateral two-stage maxillary sinus augmentation (residual crest height≤4mm) were enrolled in this split-mouth prospective randomized controlled study. One sinus side as a control group was grafted with only collagenated heterologous bone graft; the other region as a test group was grafted with hyaluronic matrix and collagenated heterologous bone graft. Bone biopsy samples were taken after 4 months during the dental implant surgery and analyzed using micro−computed tomography and histomorphometric parameters. According to the micro−computed tomography and histomorphometric results, a significantly higher percentage of new bone was observed in the test group when compared to the control group after 4 months of healing.This study confirmed the hypothesis that the addition of hyaluronic matrix to collagenated heterologous bone graft for sinus augmentation enhances bone formation compared to collagenated heterologous bone graft alone in the early healing period.

Platelet-Rich Fibrin (PRF) in Implants Dentistry in Combination with New Bone Regenerative Flapless Technique: Evolution of the Technique and Final Results.

Most common techniques for alveolar bone augmentation are guided bone regeneration (GBR) and autologous bone grafting. GBR studies demonstrated long-term reabsorption using heterologous bone graft. A general consensus has been achieved in implant surgery for a minimal amount of 2 mm of healthy bone around the implant.A current height loss of about 3-4 mm will result in proper deeper implant insertion when alveolar bone expansion is not planned because of the dome shape of the alveolar crest. To manage this situation a split crest technique has been proposed for alveolar bone expansion and the implants’ insertion in one stage surgery. Platelet-rich fibrin (PRF) is a healing biomaterial with a great potential for bone and soft tissue regeneration without inflammatory reactions, and may be used alone or in combination with bone grafts, promoting hemostasis, bone growth, and maturation.AimThe aim of this study was to demonstrate the clinical effectiveness of PRF combined with a new split crest flapless modified technique in 5 patients vs. 5 control patients.Materials and methodsTen patients with horizontal alveolar crests deficiency were treated in this study, divided into 2 groups: Group 1 (test) of 5 patients treated by the flapless split crest new procedure; Group 2 (control) of 5 patients treated by traditional technique with deeper insertion of smaller implants without split crest. The follow-up was performed with x-ray orthopantomography and intraoral radiographs at T0 (before surgery), T1 (operation time), T2 (3 months) and T3 (6 months) post-operation.ResultsAll cases were successful; there were no problems at surgery and post-operative times. All implants succeeded osteointegration and all patients underwent uneventful prosthetic rehabilitation. Mean height bone loss was 1 mm, measured as bone-implant most coronal contact (Δ-BIC), and occurred at immediate T2 post-operative time (3 months). No alveolar bone height loss was detected at implant insertion time, which was instead identified in the control group because of deeper implant insertion.ConclusionThis modified split crest technique combined with PRF appears to be reliable, safe, and to improve the clinical outcome of patients with horizontal alveolar crests deficiency compared to traditional implanting techniques by avoiding alveolar height-loss related to deeper insertion of smaller implants.

Nanohydroxyapatite promotes the healing process in open-wedge high tibial osteotomy: A CT study

BackgroundThe aim of this prospective and randomized study was to evaluate the effectiveness of adding nanohydroxyapatite (NHA) to heterologous bone graft in open wedge high tibial osteotomy (OWHTO) by measuring the bone density of the tibial osteotomy gap. MethodsTwenty-seven patients (26 knees) were operated by OWHTO and randomly divided into two groups: pure graft group, in which the osteotomy gap was filled with only heterologous bone graft; nanohydroxyapatite group, in which the osteotomy gap was filled with heterologous bone graft and NHA. All patients underwent computed tomography (CT) examination within one week after operation (Time 0), and after two months (Time 1) and 12months (Time 2). CT volume acquired Hounsfield Units (HU) were calculated and the mean value of bone density on three planes was measured. ResultsAt Time 0, the mineral density of the nanohydroxyapatite group appeared significantly higher compared with the pure graft group, due to the presence of NHA. At Time 1, the mineral density of the nanohydroxyapatite group had decreased relative to Time 0, while in the pure graft group it remained unchanged. At Time 2, the mineral density in the nanohydroxyapatite group had further decreased, reaching values close to the mineral density of normal bone. In contrast, in the pure graft group the mineral density had increased, probably due to the lack of reabsorption of the graft and the development of sclerosis in the osteotomy borders. ConclusionsThe results of the present study show better osseointegration of the heterologous graft when nanohydroxyapatite is added.