Temperature Heat Research Articles

PEMANTAUAN KEBOCORAN GAS DAN PANAS UDARA DENGAN METODE FUZZY BERBASISKAN IOT

The fuel commonly used by people for daily needs is Liquefied Petroleum Gas (LPG). LPG leaks can occur in closed spaces with temperatures above 30℃ because they contain very dangerous propane and butane compounds. If there is no early warning, the gas cylinder can expode and cause a major fire. The proposed model is capable of displaying gas concentrations and air heat (temperature and humidity) and reporting via telegram using the fuzzy mamdani algorithm. The aim of the research is to design a model for monitoring gas leaks and air heat. The sensors used in this system are tehe MQ6 sensor for gas detection, DHT22 for temperature and humidity detection, fire sensor, and nodeMCU as an Internet of Things-based processor using the fuzzy logic method. This system will turn on fan, buzzr and send a warning to telegram automatically when conditions are unsafe and dangerous. The conclusion of the research is that buzzer warning and telegram notifications make it easier for users to identify gas leaks so they can take immediate action

Temperature distribution evolution in zero-gap alkaline water electrolyzer: Experimental and modeling

Alkaline water electrolysis technology is currently the most prospective commercial choice for producing green hydrogen, however, accurately modeling the temperature distribution evolution inside the alkaline water electrolyzer is still a challenge, since the existence of strong coupling multi-physical fields among gas–liquid flow, electrochemistry and heat transfer. In this article, 3D simulation models of the zero-gap alkaline water electrolyzer are established considering the mutual coupling relationship among two-phase flow, electrochemistry and heat transfer as well as the bypass current effect to study the heat transfer property and temperature profiles under different electrolysis conditions. The simulation study is conducted for the electrolyzer consisting of five electrolysis cells. The voltage, temperature difference and gas production rate were measured experimentally and simulated well using the established models. It indicates that the average relative error is respectively 0.45% for the estimated cell voltage, 13% for the estimated outlet-inlet temperature difference of the cathode flow channel, and 1.18% for the estimated hydrogen production rate. The characteristics of temperature distribution evolution in the zero-gap alkaline water electrolyzer have been disclosed, accordingly the suitable heat management strategy has been suggested for the stable operation. The results would provide a useful guide on the optimization and design of large-scale alkaline water electrolyzer to implement long-term stable operation with low cost.

Design and research of a novel type of arc fin for heat transfer enhancement in hot water oil-displacement system

Phase change thermal storage system utilizes solar energy to provide continuous heat and electricity for offshore platforms in the petroleum industry. However, the low thermal conductivity of the heat storage medium (phase change material) in the system limits the overall heat transfer efficiency. This study focuses on the design of a novel longitudinal arc fin to enhance heat transfer in the storage system. A comparison is made between the influence of the rectangular fin and the novel longitudinal arc fin structure, as well as the impact of the fin number on the heat storage performance of the heat storage unit. A numerical model is constructed and used to analyze the grid and time step in the numerical process. The resulting data is further validated through experimental comparison. The study also examines the impact of fin structure and fin number on the internal convection and temperature of this phase change heat storage unit, comparing thermal performance parameters such as heat storage time, heat storage rate, temperature response, and overall heat storage. Findings indicate that, under constant overall fin size, increasing fin number significantly enhances the internal temperature of this unit. Additionally, changing the shape of fins from rectangular to arc-shaped results in decreased heat storage performance. Specifically, when compared to the initial rectangular structure, the melting time of 8 arc fins and 10 arc fins decreased by 30.70% and 40.65%, the mean temperature response increased by 45.01% and 67.70%, and the mean rate of heat storage increased by 45.35% and 69.23%. Therefore, increasing the number of arc-shaped fins, while maintaining the same fin volume, substantially improves the heat storage properties of the unit.

Analytical Analysis of Factors Affecting the Accuracy of a Dual-Heat Flux Core Body Temperature Sensor.

Non-invasive core body temperature (CBT) measurements using temperature and heat-flux have become popular in health, sports, work safety, and general well-being applications. This research aimed to evaluate two commonly used sensor designs: those that combine heat flux and temperature sensors, and those with four temperature sensors. We used analytical methods, particularly uncertainty analysis calculus and Monte Carlo simulations, to analyse measurement accuracy, which depends on the accuracy of the temperature and flux sensors, mechanical construction parameters (such as heat transfer coefficient), ambient air temperature, and CBT values. The results show the relationship between the accuracy of each measurement method variant and various sensor parameters, indicating their suitability for different scenarios. All measurement variants showed unstable behaviour around the point where ambient temperature equals CBT. The ratio of the heat transfer coefficients of the dual-heat flux (DHF) sensor's channels impacts the CBT estimation uncertainty. An analysis of the individual components of uncertainty in CBT estimates reveals that the accuracy of temperature sensors significantly impacts the overall uncertainty of the CBT measurement. We also calculated the theoretical limits of measurement uncertainty, which varied depending on the method variant and could be as low as 0.05 °C.

Laser Surface Transformation Hardening for Automotive Metals: Recent Progress

This article discusses recent advancements in the Laser Surface Transformation Hardening (LSTH) process applied to industrial metals. It focuses on examining the microstructure of the metal surface layer and explores different methods of performing LSTH to evaluate mechanical and surface properties. The study also investigates the utilization of various industrial lasers and simulation software for the LSTH process. The careful analysis of heat transfer and temperature control during LSTH aims to prevent the generation of surface defects like micro-cracks and surface melting. Finite element method (FEM) software effectively simulates the LSTH process. The research provides a comprehensive overview of recent developments in LSTH, categorized based on different metals and subsequent testing, highlighting its applications in the automotive industry. Electrochemical, wear, and microhardness tests are investigated to assess the potential applications of automotive metals.

Preparation and study on combustion performance of AP@ZrH2 core-shell composite energetic materials with high volume energy density

The development of composite energetic material with high volume energy density could increase the range and loading capacity of solid propellants. In this study, a series of core-shell composite energetic materials AP@ZrH2 were fabricated by decorating ZrH2 on the ammonium perchlorate (AP) through a solvent-nonsolvent method. A substantial increase in combustion heat (13373.67 J/g) and maximum burning temperature (1415.33 °C) are detected in composites in contrast to physically mixed sample (10660.46 J/g and 837.22 °C). This is due to the enhancement of the decomposition performance of AP, which provides sufficient oxidation gas atmosphere for combustion of ZrH2. In addition, the delay time (524 ms) and burning time (114 ms) of composites are significantly decreased compared to the physical mixed sample (2145 and 256 ms). The remarkable combustion performance and burning rate could be attributed to reduced mass and heat transfer distances. Finally, the improvement of combustion efficiency in the composites makes the size of the residual particles smaller.

Investigation of diabatic imparity involving asymmetric convection in two-dimensional longitudinal fins using lattice Boltzmann solver

This manuscript investigates the effect of diabatic imparity on two-dimensional (2-D) transient fins having naturally obtained non-linear variation of temperature-dependent conductivity. The diabatic imparity arises due to asymmetrical convection coefficient on the surfaces, implemented using different Biot numbers on each respective surface of the fin, which resembles pragmatic industrial applications. The transient solution of 2-D fin has been obtained using a Lattice Boltzmann (LB) solver, firstly, the suitability of 2-D LB formulation is established with the validity of the existing results, and subsequently extending the LB formulation for the present study. The numerical solution is determined under the two types of step-changing boundary conditions at the fin root having (i) heat flow and (ii) temperature. Results have been plotted graphically, and these include instantaneous isotherms, equilibrium isotherms, and threshold iso-temporal lines. Reported results facilitate the fin designer to examine the effect of diabatic imparity on the attainment of steady-state and occurrence of transverse temperature gradient on 2-D transient fin. The reported results provided are pertinent to the pragmatic application and are seldom reported in the literature. The outcomes of the present investigation are eminently informative to practising engineers and will serve as design monograms.

Analysis of Thermomechanical Stress of High-Temperature Ignition Surface Caused by Drop–Wall Interaction at Engine Conditions

Abstract Drop–wall interaction is a complex phenomenon encountered in diverse industrial applications. An important example is fuel droplets impinging on a high-temperature ignition plug in a direct-injection compression-ignition engine. The ignition plug, comprised of heat-resistant materials, will experience thermal shock due to abrupt temperature changes. The ensuing temperature fluctuation in the solid wall induces thermal stress, and if this stress surpasses the material's strength in that mode, failure can occur. Therefore, it is imperative to analyze the temperature dynamics on the high-temperature surface to enhance material durability. This study focuses on drop–wall interactions in the engine environment. Utilizing the Smoothed Particle Hydrodynamics (SPH) method, this research simulates fuel droplet impingement on an ignition plug with various materials to characterize heat transfer, thermal penetration, and temperature distributions in the heated wall. The investigation also delves into the behavior of ceramic material, specifically silicon nitride, assessing its thermomechanical stress and durability based on the stress–number of cycles (S-N) curve. Thermal stress is computed by considering temperature gradients and material properties, while mechanical stress is evaluated based on the bending momentum and momentum flux induced by the spray. A parametric study explores diverse materials such as tungsten carbide, iron, stainless steel, carbon steel, and aluminum. Results indicate that thermal stress outweighs bending and spray-induced stress. Moreover, the analysis reveals that silicon nitride exhibits the lowest thermal stress distribution and superior durability, potentially capable of operating for infinite cycles under engine-relevant conditions.

Nozzle effects on spray combustion and emissions in compression ignition engines using waste cooking oil biodiesel: A computational fluid dynamics analysis at varying injection pressures

AbstractThis study investigates the spray combustion characteristics of waste cooking oil (WCO) in comparison between a swirl nozzle (SN) and a conventional nozzle (CN) of equal cross‐section. n‐Heptane, methyl decanoate, and methyl‐9‐decenoate were used as WCO substitutes in the simulation. The research primarily focuses on multiphase flow using the Lagrangian‐drop Eulerian‐fluid (LDEF) method, employing an equilibrium phase spray model (EP) for droplet behaviour analysis. The model's efficacy was validated through comparisons with experimental works by other engine researchers. At varying injection pressures, the study found that SN slightly reduced evaporative spray tip penetration but increased the cone angle compared to CN. This suggests early fuel jet disintegration and improved air entrainment due to SN. SN also showed a higher heat release rate and temperature, with soot reduction between 3.20 to 6.72% as injection pressure increased from 100 to 300 MPa. This indicates that SN achieves better air‐fuel mixture than CN. Further, the study discovered that the influence of SN becomes more significant as the rheological properties of WCO lessen under ultra‐high injection pressures.

Multi-objective optimization and benefit evaluation of heat pump system for tobacco drying using waste heat from data center

Tobacco drying is a highly energy-consuming process that requires a large amount of thermal energy. In this study, the waste heat from a data center is utilized to reduce fossil energy consumption in the tobacco drying process. A heat pump system is designed to address the issue of the waste heat temperature from the data center not meeting the required temperature for tobacco drying. Multi-objective optimization is performed with the goal of maximizing the specific moisture extraction rate and minimizing the specific investment cost, and seven hydrofluoroolefins are selected as the circulating working fluids. Coal-fired tobacco drying and Air Source Heat Pump Tobacco Drying (ASHPTD) are selected as comparison benchmarks to evaluate the energy efficiency and environmental benefits of the Data Center Waste Heat Tobacco Drying (DCWHTD) method in this study. The results indicate that R1234ze(Z) is the best working fluid. The specific moisture extraction rate of DCWHTD is improved by 36.69% and 20.21% compared to the coal-fired tobacco drying and ASHPTD, respectively, demonstrating enhanced energy efficiency. Although the specific investment cost of DCWHTD is higher compared with the coal-fired tobacco drying, it is 21.00% lower than that of ASHPTD. DCWHTD produces fewer emissions, the life-cycle carbon emissions are 26.93% and 16.80% lower than that of the coal-fired tobacco drying and ASHPTD, respectively. Furthermore, waste heat recovery improves the energy reuse efficiency of the data center by 64.92%. The tobacco drying method proposed in this study has better comprehensive performance and greater application potential.

Comprehensive in silico characterization of NAC transcription factor family of Pinellia ternata and functional analysis of PtNAC66 under high-temperature tolerance in transgenic Arabidopsis thaliana

Pinellia ternata, a valuable Chinese herb, suffers yield reduction due to “sprout tumble” under high temperatures. However, the mechanisms underlying its high-temperature stress remain poorly understood. NAM, ATAF1/2, and CUC2 (NAC) transcription factors regulate plant tissue growth and abiotic stress. Hence, there has been no comprehensive research conducted on NAC transcription factors in P. ternata. We identified 98 PtNAC genes unevenly distributed across 13 chromosomes, grouped into 15 families via phylogenetic analysis. Gene expression analysis revealed diverse expression patterns of PtNAC genes in different tissue types. Further studies revealed that PtNAC5/7/17/35/43/47/57/66/86 genes were highly expressed in various tissues of P. ternata and induced by heat stress, among which PtNAC66 was up-regulated at the highest folds induced by heat temperature. PtNAC66 is a nuclear protein that can selectively bind to the cis-responsive region NACRS but lacks the ability to activate transcription in yeast. For further research, PtNAC66 was cloned and transgenic Arabidopsis was obtained. PtNAC66 overexpression increased high-temperature tolerance compared to wild-type plants. Transcriptome profiling demonstrated that overexpression of PtNAC66 led to significant modification of genes responsible for regulating binding, catalytic activity, transcription regulator activity and transporter activity response genes. Additionally, PtNAC66 was found to bind the promoters of CYP707A3, MYB102 and NAC055, respectively, and inhibited their expression, affecting the high-temperature stress response in Arabidopsis. Our research established the foundation for functional studies of PtNAC genes in response to high-temperature forcing by characterizing the P. ternata NAC gene family and examining the biological role of PtNAC66 in plant high-temperature tolerance.

Assessment of the Possibility of Excluding Secondary Heating of the Inflow During the Warm Period in Modern Climatic Conditions

The subject of the study is the dependence on the required indoor air temperature and the accepted inflow temperature for a minimum heat and humidity ratio in the room, in which secondary heating of inflow can be excluded. The purpose of the study is to obtain an analytical expression of this dependence, which allows an engineering assessment of the possibility of eliminating secondary heating in the process of designing air conditioning systems without the use of graphical constructions. The objective of the study is to represent an adequate flow processing scheme on the I–d diagram, identify the main factors affecting the minimum heat and humidity ratio in the room and obtain the necessary numerical coefficients in formulas linking the desired and initial parameters. Research results. An analytical dependence is obtained that allows calculating the minimum possible value of the heat and humidity ratio in a room in which secondary heating is not required, and only cooling of the inflow with drying in a surface air cooler is sufficient if it has a bypass channel. The presentation is illustrated with numerical and graphical examples.

Characterization of the acoustic pressure waveforms in Rijke tubes with spatially varying heat sources and temperature distributions

In this work, we implement an asymptotic expansion technique that leverages a small perturbation parameter that arises in the context of one-dimensional tubes with open-open end point configurations and spatially varying heat sources. This approach, when paired with a spectral collocation eigensolver, enables us to produce accurate predictions of the pressure mode shapes and frequencies over a wide range of parameters. These include the temperature gain across the heat source, the heat source length and location, and the overall thermal profile. The latter is intended to reproduce different flow heating configurations that emulate Rijke tube characteristics. Specifically, this investigation begins by considering three piecewise representations of the heat source by juxtaposing constant–constant temperatures before and after a heating element whose temperature is prescribed locally using three analytical functions: linear, exponential, and power-law profiles. This is followed by a logistic distribution that can be globally applied to provide a uniformly valid, continuous, and differentiable thermal profile spanning the entire tube, including the heat source element. Our fundamental formulation relies on Green's functions and an integral formulation that enables us to extract all acoustic frequencies analytically. These are found to increase monotonically with successive elevations in the temperature gain across the heat source, retractions of the heat source, length reductions in the heat source, and smoothing of the temperature gain. Along similar lines, the pressure mode shapes are found to exhibit blunter and often linear variations for higher temperature gains, longer heat sources, and upstream displacements of the heat source toward the inlet.

A new random walk method for simulating heat flow and temperature distribution in three-dimensional discontinuous systems

Numerical methods for analyzing diffusion phenomena involving strong discontinuities and complicated interfaces are of great scientific and technical importance. In this paper, we extend the existing step-balanced random walk, which overcomes the problem of detailed balance of a random walker in three-dimensional (3D), diffusion-tensor discontinuous systems, to particle density (ρ) discontinuous systems, and introduce volumetric heat capacity C and temperature T by considering ρ as heat density, i.e., ρ=CT, to apply it to thermal problems. Two types of thermophysical simulations are demonstrated: one is steady-state heat flow due to a temperature difference at the end surfaces on a two-phase slab model unit cell with periodic boundary conditions; the other is the time variation of temperature distribution due to heat diffusion from a point heat source in a repeated two-phase slab model with no periodic boundary conditions. We see the correct behavior of heat and temperature expected in 3D discontinuous systems composed of two phases with anisotropic thermal conductivity. The applicability to problems other than pure diffusion and the limitations of the method are also discussed.

Effect of Different Temperature and Nuclear Data Libraries in Criticality Calculations of 300 MWt Molten Salt Reactor

The Molten Salt Reactor (MSR) is a type of reactor in which coolant and fuel are blended with liquid salts. Liquid fuel enhances heat transfer and temperature control, establishing the MSR as one of the Generation IV reactor types. This study aims to analyze the impact of temperature variations on MSR reactor criticality and evaluate the effect of different nuclear data libraries, namely JENDL 3.2, JENDL 3.3, and JENDL 4.0, in neutron analysis. The observed temperature variations are 600 K, 700 K, 833 K, 903 K, and 1000 K. The analysis spans low to operational temperatures to comprehend reactor performance under differing thermal conditions. The study is conducted on a 300 MWTh MSR design, utilizing SRAC2006 with PIJ and CITATION modules for calculations. The results reveal the impact of temperature variations and nuclear data library disparities on reactor criticality. The outcomes demonstrate that higher temperatures correspond to lower values of the effective multiplication factor. At lower temperatures, neutrons experience greater moderation compared to higher temperatures. As a result, a higher number of thermal neutrons influences an increased probability of fission reactions within the reactor. Different nuclear data libraries also yield varied criticality values due to differing cross-sectional areas and quantities of data within each JENDL library. JENDL 4.0 generates the highest criticality value, attributed to elevated cross-sectional regions of each respective nuclear data entry and a greater quantity of nuclear data entries than JENDL 3.2 and JENDL 3.3.

Research on the thermal performance and stability of three-dimensional array pulsating heat pipe for active/passive coupled thermal management application

The efficient heat transfer performance of three-dimensional pulsating heat pipes can effectively deal with the heat dissipation problems in the field of electronics integration. However, the large contact thermal resistance and complex layout limit the actual cooling efficiency. In this study, a novel three-dimensional array pulsating heat pipe (3D-APHP) with a dual-plane structure was designed. The top and bottom of the 3D-APHP are mounted with flat plates, and the center section is connected by multiple parallel array tubes. The planar and array structures enhance the flexibility in the actual layout of the pulsating heat pipe to accommodate space constraints. The effects of different conditions (working fluid, filling rate, heating power, tube diameter and installation condition) on the heat transfer performance and uniform temperature performance of 3D-APHP were investigated. It is found that 3D-APHP demonstrates efficient heat transfer capability and temperature uniformity. The minimum thermal resistance and maximum thermal conductivity can reach 0.059 °C/W and 170.1 KW/m °C, respectively. Moreover, 3D-APHP exhibits good heat transfer performance across different installation positions with a maximum thermal resistance not exceeding 1.1 °C/W, revealing significant potential for applications. Meanwhile, the two-phase heat transfer process inside the 3D-APHP was analyzed. The uniform vapor–liquid plug distribution can significantly strengthen the thermal performance of the 3D-APHP.

Sensitivity analysis and thermodynamic evaluation of a combined cooling, heating and power system utilizing exhaust gases of smelting furnace

Exhaust gases from the smelting furnace have high temperature and mass flow rate, and there is huge potential to use them for energy-related purposes such as electricity generation, cooling and heating. Utilization of the gases for energy-related purposes would lead to fuel savings and emissions reduction. To use this potential, it is necessary to design proper systems and cycles and apply a heat recovery unit. Several technologies are useable for heat recovery depending on the characteristics of exhaust gases, such as their mass flow rate, temperature and compositions. Due to the higher potential of combined heating, cooling and power (CCHP) generation systems compared with the systems with a single output, a CCHP is designed and investigated in the present study by consideration of the specifications of the exhaust gases. The applied system in this study comprises a Supercritical CO2 (SCO2) cycle, heat exchanger and single-stage absorption chiller for simultaneous heating, cooling and power production. Engineering Equation Solver (EES) is employed to model the proposed system by considering the properties of the flows and characteristics of the components. To get deep insight into the effective parameters on the outputs of the designed system, the impact of three factors, namely the mass flow rate of the gases, the effectiveness of heat exchanger and temperature of exhaust gases, are analyzed and investigated by the implementation of sensitivity analysis. As one of the main conclusions, it is found that an increment in the mass flow rate of exhaust gases from 30 kg/s to 70 kg/s causes augmentation in the power generation from 2037 kW to 4754 kW. Furthermore, exergy analysis is carried out, and it is found that an increase in the temperature or mass flow rate of exhaust gases or a decrease in the effectiveness of heat exchangers would lead to decrement in the exergy efficiency of the system. According to the performed sensitivity analysis, the mass flow rate of exhaust gases has the most remarkable influence on the heating and cycle-generated power among the considered factors.

Effect of Cross Nanowall Surface on the Onset Time of Explosive Boiling: A Molecular Dynamics Study

Explosive boiling is a fast-phase transition from an ultra-thin liquid film to vapor under an extremely high heat flux, which typically has been studied using the molecular dynamics simulation (MDS) method. The present MDS study investigated the explosive boiling of a liquid argon nanofilm over different solid copper surfaces with different nanowall patterns, including parallel and cross nanowalls. For each surface, atomic motion trajectories, the number of liquid and vapor argon atoms, heat flux, and, mainly, the onset time of explosive boiling were investigated. The simulation results indicated that explosive boiling occurs earlier on parallel and cross nanowall surfaces than on an ideally smooth surface, regardless of the topology and configuration of the nanowalls. Moreover, the results revealed that by using the cross nanowall surfaces, the onset time of explosive boiling decreased by 0.7–4% compared to the parallel nanowall surfaces. In addition, it was found that the onset time of explosive boiling strongly depends on the potential energy barrier and the movement space between nanowalls for both parallel and cross nanowall surfaces. Furthermore, the simulation findings showed that even though increasing the height of cross nanowalls increases the heat flux and temperature of the fluid argon domain, it does not necessarily result in a shorter onset time for explosive boiling. These findings demonstrate the capability of cross nanowall surfaces for explosive boiling, thereby being utilized in future surface design for thermal management applications.

Temperature stress (cold and heat) strongly affect the phytotoxicity of polycyclic aromatic hydrocarbon (phenanthrene) to wheat

AbstractAnthropogenic activity could create different threats leading to irreversible changes in the global environment and, as a consequence, posing varied stressful conditions acting together (combined stress) on organisms. Our research concerned the combined stress of two of the main threats to soil health and plant health: temperature stress and pollution. The aim of this research was the quantitative assessment of the impact of temperature stress on the phytotoxicity of PAHs (polycyclic aromatic hydrocarbons; specifically, phenanthrene, which is a widespread, harmful organic contamination of soil) on the growth of wheat seedlings in relation to the level of soil contamination by phenanthrene (0–1000 mg kg−1 dry mass of soil) and the type of temperature stress: cold (10°C) and heat (35°C) stress, in three different soils. Earlier studies have investigated the effect of temperature stress on PAH toxicity mainly on soil invertebrates. However, the impact of temperature stress on PAH phytotoxicity towards crop plants, which are important for human food security but could be affected by chemical soil degradation, is still poorly understood. Our results indicated that the phenanthrene phytotoxicity was significantly enhanced by cold stress and heat stress. The effects of cold and heat temperature stress increased with increasing phenanthrene level. Our research is important for improving the risk assessment of PAH and food security forecasting.

Evaluation of methods used for simulation of heat-affected zones in duplex stainless steels

The weldability of duplex stainless steels partly depends on the ferritization of the high-temperature heat-affected zone (HT-HAZ). This area is rather narrow, and it can be challenging to visualize and determine its actual impact on the properties. To address this, various methods were applied to study the grain growth and austenite reformation in the HT-HAZ of the lean duplex grade UNS S32101. Thermo-mechanical Gleeble® simulations were conducted at 1360 °C with different holding times and cooling rates. Subsequently, the grain size and ferrite content were measured on polished and etched cross-sections. Bead-on-plate welds were performed on the same heat of 6-mm plate thickness using the gas tungsten arc welding (GTAW) process. The shielding gas was Ar + 0–8% N2 to illustrate the effect of nitrogen additions on the HT-HAZ morphology. The arc was either stationary, welding at one spot for 0.5–120 s, or travelling at different speeds to generate varying heat inputs and temperature gradients. The thermo-mechanical simulations approximated the results obtained by travelling arc welding and allowed for a more comprehensive investigation. Stationary arc welding was not suitable for HT-HAZ studies as it quickly caused nitrogen depletion and resulted in significantly higher ferrite contents compared to the travelling arc welds.