Heat Exchanger Research Articles

Thermal performance of shell-and-tube polymeric hollow fiber heat exchangers as oil coolers

Motor oil must be appropriately treated in motors, and aluminum plate heat exchangers are used to cool it. An aluminum heat exchanger is an additional part of the oil treatment module, which increases its size and weight. Two compact plastic shell-and-tube heat exchangers were tested alongside with aluminum heat exchanger to evaluate the efficiency of the plastic cooling core inside the oil module. A total of 63 experimental points were tested on three heat exchangers with good thermal balance (discrepancy of about 1,8 %), and the data were used to evaluate the heat transfer coefficients. While plastic unit PA11 showed the heat outputs exceeding the heat output of the aluminum plate unit by about 7 %, the pressure drops were about ten times higher. The unit PEEK showed good performance and pressure drops on the oil side, but the heat transfer was limited by a small heat transfer surface. Analysis of thermal resistances confirmed that the thermal resistance between the wall and the oil is dominant due to the oil's low thermal conductivity and high viscosity. The results showed that optimization of the fiber structures is needed, aiming to increase the oil flow around the fiber structures.

Numerical study of magneto convective ag (silver) graphene oxide (GO) hybrid nanofluid in a square enclosure with hot and cold slits and internal heat generation/absorption

Energy transmission is widely used in various engineering industries. In recent times, the utilization of hybrid nanofluids has become one of the most popular choices in various industrial fields to increase thermal performance and enhance power generation, entropy reduction, solar collectors, and solar systems. Motivated by this wide range of applications, the present article explores the mixed convection flow and heat transfer of magnetohydrodynamic \\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:Ag$$\\end{document} (Silver) and \\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:GO$$\\end{document} (Graphene) nanofluids hybrid nanofluids in a square enclosure with heat generation/absorption by using the MAC method. The vertical walls of the enclosure are assumed to be adiabatic. The horizontal walls are also assumed adiabatic except for the center portion of the top and bottom walls of the cavity. The center portion of the horizontal upper wall is maintained as a cold is \\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:{(T}_{c})$$\\end{document}and the lower wall is maintained as hot \\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:\\left({T}_{h}\\right)$$\\end{document}. The dimension equations are transformed into dimensionless form and then discretized and solved with the finite difference Marker and cell (MAC) method. Numerical modelling is implemented, by changing Richardson number \\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:\\left(Ri\\right)$$\\end{document}, The results are located graphically using MATLAB software. The Nusselt number graph was displayed for the Reynolds number (Re), Richardson number\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:\\:\\left(Ri\\right)$$\\end{document}, and Hartmann number \\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:\\left(Ha\\right)$$\\end{document}. The findings show that enhancing the values of the Richardson number and Reynolds number enhances the Nusselt number values except for the Hartmann number. The findings indicate that the combination of the new model is very good at predicting thermal conductivity and correlates experimental results well. The augmenting strength of magnetic force diminishes fluid flow. Developing the coefficients for the heat source and sink improves energy transmission and heat transfer enhancement. Hybrid nanofluids like \\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:Ag-GO$$\\end{document} enhance heat transfer and efficiency. They improve cooling in heat exchangers, radiators, and electronics, boost solar energy systems, aid in cancer treatment and drug delivery, enhance geothermal and wind turbine efficiency, and improve manufacturing processes. Overall, they optimize thermal management in various applications.

Energy-Efficient Architectural Design of a Banquet Hall with Integrated Tunnel Ventilation: Monitoring Performance During the Transitional Season in China

The construction industry, a significant contributor to global energy consumption and greenhouse gas emissions, is under considerable pressure to adopt transformative approaches. Public buildings, which account for a substantial portion of total energy usage, must balance high standards of thermal comfort with ventilation efficiency. In China, many public buildings are part of urban landscapes, where façade designs often limit natural ventilation. Consequently, technologies like earth-to-air heat exchangers and wind towers are increasingly essential for enhancing natural ventilation. However, research on the efficacy of these systems remains sparse. This study examines the transitional seasonal environment by evaluating the thermal-humidity index of a banquet hall equipped with an earth-to-air heat exchanger system. Using DeST software [DeST 2.0], the study simulates indoor natural ventilation, calculates ventilation rates, and assesses residual heat removal efficiency. The system’s performance is also modeled under various thermal design zones. Results demonstrate that under natural ventilation, the system can achieve a residual heat removal efficiency of up to 490%. Simulations across different climate zones indicate that the system performs best in regions with extreme temperature fluctuations, particularly those with hot summers and warm winters. In these areas, the system reduces the annual temperature difference by up to 56.7%, significantly improving thermal comfort and reducing dependency on air conditioning. In contrast, performance in milder regions like Kunming achieves only a 37.5% reduction in temperature difference. Overall, this study provides valuable insights into energy-efficient design strategies and thermal optimization for banquet halls, with significant potential for energy savings and enhanced occupant comfort.

Does cabbeling shape the thermohaline structure of high-latitude oceans?

Abstract Vertical exchange of heat and carbon in the ocean regulates Earth’s climate. Convection, a driver of near surface exchange, occurs when dense water overlies light water. Fofonoff (1957) pointed out that when lighter overlying cold-fresh water mixes with denser underlying warm-salty water, the mixture can become denser than the underlying water due to a nonlinear process known as cabbeling. He suggested that such profiles, despite being gravitationally stable, could be classed as being unstable to cabbeling. Fofonoff (1957) hypothesised that, by mixing away such profiles, cabbeling may be shaping the thermohaline structure of polar oceans. We investigate this hypothesis here. In a one-dimensional model we find that convective mixing occurs in temperature inverted profiles that are unstable to cabbeling even when they are initially gravitationally stable. In data from an observationally constrained global circulation model, we find profiles with a temperature inversion larger than −0.5°C are unstable to cabbeling less than 0.02% of the time and in high quality in-situ observations they are unstable less than 12% of the time. We find that due to cabbeling larger temperature inversions, which should weaken stratification, make profiles more stable. Our results suggest that cabbeling limits the stability behaviour of temperature inverted profiles and influences the thermohaline structure in parts of the ocean where cold-fresh water overlays warm-salty water.

Study on the heat transfer performance of coaxial casing heat exchanger for medium and deep geothermal energy in cold regions

To accurately assess the heat transfer performance of a medium-depth coaxial casing heat exchanger, this study introduced the concepts of the annual stabilized mining stage and the effective thermal influence distance for each layer of non-homogeneous thermal storage. The study area was stratified into six layers based on the geothermal temperature gradient fitting results. The findings revealed that the maximum injected circulating fluid temperature for the mid-depth coaxial casing geothermal system was 37 °C, with a maximum mass flow rate of 16.67 kg/s. When the injected circulating fluid temperature increased from 2 °C to 25 °C, the duration of the annual stabilized exploitation stage extended from 23 to 26 years. Similarly, increasing the injected circulating fluid mass flow rate from 2.78 kg/s to 16.67 kg/s prolonged the maintenance period in the annual stable mining stage from 22 to 28 years. The study further indicated that the effective thermal influence distance for each layer of thermal storage was significantly impacted by varying injection circulating fluid temperatures. These results offered theoretical insights into the heat transfer performance of medium-depth coaxial casing geothermal systems under both short- and long-term operational conditions.

La-Fe-Si magnetocaloric composite with anisotropic microstructure prepared by hot pressing

In this study, we have proposed an anisotropic microstructure in La-Fe-Si magnetocaloric composites for thermal management. This is vital to the rapid heat exchange and high working efficiency in magnetic refrigerator system. We demonstrate the anisotropic microstructure in composites can be fabricated via powder metallurgy in this work. By adjusting the particle size of the 1:13 phase, the introduced reinforcing phase with rheological property can effectively deform and anisotropic microstructure can be obviously observed. This can be attributed to the tailored stress distribution in cubic-anvil-type pressure apparatus. The element diffusion between the two phases was also discussed in this paper, taking into account the influence of particle size. Such anisotropic microstructure causes some other anisotropic physical properties in the composite, such as mechanical strength. The compressive measurements along the axial direction exhibit superior mechanical properties (~ 3.5% for strain and ~ 350 MPa for strength) compared to those along the radial direction. Attributed to the stress buffer-effect provided by the introduced ductile phase, magnetocaloric effect (magnetic entropy change ~ 7.8 J/kg K) can be maintained in the La-Fe-Si composite.

Metal Hydride Storage Systems: Approaches to Improve Their Performances

AbstractMetal hydrides provide a safe and efficient way to store hydrogen. However, current metal hydride storage systems, i.e., hydrides incorporated within a storage tank, are far from efficient. Depending on the design, (dis)charging rates may be very long. However, this can be significantly improved by implementing strategies tackling the issue of heat management at the level of: i) the metal hydride bed, and ii) the overall storage system design. This review summarises recent progress in tackling heat management of hydride systems. In this respect, modeling has emerged as a powerful tool. In particular, simulation results show that the compaction of hydride powders with binders and the use of metal foams are both effective in lifting the poor thermal conductivity of hydride beds. For tank designs, cylindrical shapes remain the preferred choice because of the flexibility and ease of supplementing heat management with fins and tubular heat exchangers. The addition of phase change materials to the hydride tank can lead to further heat storage, but any add‐on to simple hydride tanks can only lead to cumbersome systems. It is still a fine art to tune the thermal conductivity of hydride beds while selecting a suitable metal hydride alloy composition.

Solar Passive House Conceptand Thermal System Design

This aricle puts forward a concept of family home enclosed in a greenhouse. Inspired by Naturhus and Earthship ideas, it leverages thermofluid technologies inspired by nuclear power passive cooling systems. The solar gain of the greenhouse allows for enhanced heating fuel efficiency in winter, while a system of solar-drive heat exchangers dissipates excess heat in summer. This general living qualities of such innovative housing concepts are discussed, followed by an outline of the computational challenges that need to be overcome by experiment-driven modelling, aiming for the demonstrator that successfully controls summer daily temperature peaks.

Uncertainty propagation of initial conditions in thermal models

The operation of machine tools often demands a highly accurate knowledge of the tool center point’s (TCP) position. The displacement of the TCP over time can be inferred from coupled thermal models, which comprise a set of geometrically coupled heat equations. Each of these equations represents the temperature in part of the machine, and they are often formulated on complicated geometries. The accuracy of the TCP prediction depends highly on the accuracy of the model parameters, such as heat exchange parameters, and the initial temperature. Thus it is of utmost interest to determine the influence of these parameters on the TCP displacement prediction. In turn, the accuracy of the parameter estimate is essentially determined by the measurement accuracy and the sensor placement. Determining the accuracy of a given sensor configuration is a key prerequisite of optimal sensor placement. In this paper, we develop a thermal model for the discretization of realistic machine tool. On top of this model we propose two numerical algorithms to evaluate any given thermal sensor configuration with respect to its accuracy. We compute the posterior variances from the posterior covariance matrix with respect to an uncertain initial temperature field. The full matrix is dense and potentially very large, depending on the size of the discretized model. We first present a way to compute this approximation, which relies on the computation of the model sensitivities with respect to the initial values. Additionally, we present a low-rank tensor method which exploits the underlying system structure. We compare the efficiency of both algorithms with respect to runtime and memory requirements and discuss their respective advantages with regard to optimal sensor placement problems.

Corrosion-Resistant Polymer Composite Tubes with Enhanced Thermal Conductivity for Heat Exchangers

The heat transfer surfaces of heat exchangers are usually made of metals which may suffer from severe corrosion. When corrosive fluids are present, highly corrosion-resistant metals, graphite or ceramics are used, resulting in high costs. This study presents measured data on the thermophysical and mechanical properties of recently developed corrosion-resistant polymer composite tubes for use in heat exchangers. Extruded polymer composite tubes based on polypropylene or polyphenylene sulfide filled with graphite flakes were investigated. The anisotropic thermal conductivities of the polymer composite tubes were measured at various temperatures. The through-wall thermal conductivity of the tubes made of polypropylene filled with 50 vol.% graphite is increased by a factor of 30 compared to pure polypropylene, resulting in a thermal conductivity of 6.5 W/(m K) at 25 °C. The tubes composed of polyphenylene sulfide filled with 50 vol.% graphite have a through-wall thermal conductivity of 4.5 W/(m K) at 25 °C. The mechanical properties of the polymer composites were measured using tensile and flexural tests at different temperatures. The composite materials are more rigid and keep their mechanical properties up to a higher temperature level compared to the unfilled polymers. Surface roughness measurements show the very smooth and sealed surface of the composite tubes. The results contribute to establishing the viability of using polymer composites for heat exchanger applications with corrosive fluids.

Thermal resistance capacity model for transient simulation of capillary-box heat exchangers

In this paper, a novel simplified hybrid model is developed to simulate the transient thermal behaviors of capillary-box heat exchangers (CBHEs) buried in the seabed, serving as the front-end heat exchangers in seawater source heat pump system (SWHPs). The thermal resistance and capacity (TRC) approach is applied for derivation of the governing equations inside and outside the heat exchangers. Also, an analytical solution is integrated to model heat transfer in the seabed base. The effects of seawater seepage on the thermal performance of CBHEs are taken into account in the present model. The state-space representation is used to solve the governing equations. The model is verified against experimental data, achieving very good agreement with the mean bias error (MBE) of 7.2 %. A comparison with a three-dimensional computational fluid dynamic (CFD) model indicates that the TRC model's maximum relative error and MBE are 0.7 % and 2.0 % lower than those of the CFD model. Additionally, the ratio of the time required by the CFD and TRC models for a 31-day run was 138. These results demonstrate that the TRC model is sufficiently accurate and fast in the thermal simulation of CBHEs. Furthermore, the thermal properties of CBHEs are examined using the present model. The model in this study provides practical implications for heat transfer analysis and design improvement of CBHEs utilized in SWHPs.

Improving sustainability: Exergy, energy analysis and CO2 mitigation of greenhouse integrated with thin-film photovoltaic and earth-to-air heat exchanger

Adopting passive cooling systems has become especially vital due to the high energy consumption and adverse impacts of conventional air conditioning systems on the environment. Sustainable green energy structure development includes a periodic thermal model of a greenhouse integrated with thin-film photovoltaics (GiTPV) and the earth-to-air heat exchanger (EAHE). The system can provide plants in the greenhouse with air from extreme weather conditions: 5 °C in the winter and 45 °C in the summer, corresponding to thermal comfort standards in structures. According to the results, at 0.5 kg/s air mass flow rates of EAHE, the air temperature in the greenhouse room rises by 5 °C in the winter and falls by 17 °C in the summer. The greenhouse can save 9864 kWh/year before and 41,587 kWh/year after integrating EAHE. The seasonal energy efficiency ratio (SEER) for EAHE varies between 1 and 3. The yearly carbon credit of a greenhouse is expected to be 3166 US dollars, and EAHE reduces CO2 emissions by around 65.68 tons per year. Finally, the Quonset GiTPV system generates 29.22 kWh and 17.6 kWh of electrical energy per day on extremely hot and cold days respectively, making the system self-sustainable.

Cooling characteristics of nanofluids in a snowflake and squid fin composite bionic microchannel heat sink

To improve the heat dissipation performance of electronic components, this study proposed a novel biomimetic microchannel design inspired by snowflakes and squid fins. A numerical simulation method was employed to investigate the cooling characteristics of nanofluids at different concentrations within this biomimetic microchannel heat sink. The microchannel is shaped like a snowflake, while the base plate features a biomimetic squid fin structure. The study focused on analyzing the effects of waveform height (amplitude A = 0.1–0.4 mm) and waveform frequency (B = 0.5–2π) on heat transfer performance. The results indicated that when nanofluids flow over a base plate with a wavelength frequency of B = 0.5π, there is a significant enhancement in heat exchange while simultaneously reducing flow resistance. In the microchannel heat sink (A = 0.3 mm, B = π), the thermal conductivity of the nanofluids can be increased by up to 32.56 %, with a maximum comprehensive evaluation index of 1.68. This research provides important guidance for the application of nanofluids and biomimetic microchannels in the thermal control of electronic devices.

Tetrahybrid nanoparticles through squeezed channel with inclined Lorentz forces

Heat exchangers, nuclear power plants, and other engineering and manufacturing operations all involve high temperatures. These systems have a very big temperature gradient, which has a substantial impact on the fluid's transport characteristics. Under such circumstances, using the linear Boussinesq approximation and taking into account the constant thermophysical parameters for the ambient liquid become meaningless. Thus, under the impact on the angled magnetic field and joule heating, the radiative convection flow of the blood-based tetrahybrid nanoliquid in a squeezing channel is examined in this work. The base fluid that contains the distributed alumina, gold, silver, and titania nanoparticles is blood. Through suitable transformations, the partial governing equations were decreased into nonlinear ordinary differential equation's, which are then resolved mathematically applying the fourth-order accurate BVP4C technique. The increase in the viscous dissipation parameter corresponds toward the notable elevation on the blood temperature profile. The rate of heat transfer 57.4519% improved in Au-Ag-Al2O3-TiO2/blood than that of pure blood.

Study of nonequilibrium regenerative heat exchange in positive displacement compressors

BACKGROUND: An important task in the design of thermal engines is the evaluation of power losses in different processes to determine the installation efficiency. One of the processes that generates power losses in the compressor is the process of nonequilibrium regenerative heat exchange (NRHE) of the compressed gas with the working cavity walls. This heat exchange occurs at a significant temperature difference, which can lead to noticeable power losses. Modern compressor design methods do not consider losses from nonequilibrium regenerative heat exchange and do not describe them separately from other types of losses. AIM: This study investigates the mechanism of losses during regenerative heat exchange between the gaseous working flow out and the working cavity walls and evaluates the scale of these losses. METHODS AND RESULTS: This work provides a qualitative description of the mechanism for the formation of losses from NRHE. As a result of solving the problem of unsteady thermal conductivity, an analytical expression for calculating such losses is derived based on the Gouy-Stodola theorem. CONCLUSIONS: The study revealed that power losses from NRHE account for a significant share in the overall balance of machine losses. Parameters influencing the magnitude of these losses were also determined, and recommendations were developed to reduce them.

Heat Transfer in Double Pipe Heat Exchangers with Small Tube Spacing

Abstract In this current work, the heat transfer in double pipe heat exchangers with small tube spacing is analysed. This type of heat transfer is generally described in many literary sources, however, in laminar flow, the resulting values of the theoretical equations differ. Moreover, the small spacing of the pipes can affect the fluid flow and subsequent heat transfer. The suitability of using available theoretical methods for the design of double pipe heat exchangers (the Stephan, VDI and Baehr methods) was evaluated. A series of experiments was carried out on a double pipe heat exchanger with a tube spacing of 1.4 mm. The experimentally determined value of the heat transfer coefficient was up to two times higher in comparison with the values calculated according to theoretical methods. The relative increase was more significant for the lower Reynolds number values. At the same time, the difference of the wall temperature along the circumference of the outer tube was detected. This phenomenon was theoretically analysed and can be explained by tube misalignment in the small tube spacing. The procedure of quantification of this effect was proposed. This effect may cause an inhomogeneity of the media flow and temperature distribution and, as a result, increase the performance of the heat exchanger by tens of percent.

Comparative Study on the Effect of External Magnetic Field on Aluminum Alloy 6061 and 7075 Resistance Spot-Welding Joints

This study investigates the effects of the external magnetic field on the microstructure and mechanical property aluminum alloy 6061-T6 and 7075-T651 resistance spot welding joints. The melting behavior of 6061 and 7075 was analyzed via the calculation of the phase diagram (CALPHAD) technique. The CALPHAD results indicate that, for the 6061 aluminum alloy, the liquid fraction shows a minimal increase at the beginning stage during the solid–liquid phase transition process but with a sharp rise at the ending stage (near the liquidus). In contrast, for the 7075 aluminum alloy, the liquid fraction gradually increases throughout the entire solid–liquid phase transition process. The differences in melting behavior between the 6061 and 7075 alloys lead to different liquation crack morphologies in their spot-welded joints. In the 6061 alloy, the cracks tend to be “eyebrow-shaped”, allowing the liquid metal in the nugget to feed the gaps, and this does not significantly compromise the mechanical properties of the joint. In contrast, the 7075 alloy develops slender cracks that extend through the partially melted zone (PMZ), making it difficult for the liquid metal to feed these gaps, thereby significantly deteriorating the joint’s mechanical strength. Compared to conventional resistance spot-welding joints, the heat exchange between the nugget and the workpiece is enhanced under the external magnetic field, leading to a wider PMZ. This exacerbates the detrimental effects of liquation cracks on the mechanical properties of the 7075 joints. Lap-shear tests indicate that the mechanical properties of the 6061 aluminum alloy joints are improved under electromagnetic stirring. For 7075 aluminum alloy joints, the mechanical properties improve when the welding current is below 34 kA. However, when the welding current exceeds 34 kA, because the widening of the PMZ increases the tendency for liquation cracks, the joint’s mechanical property is deteriorated.

Irreversibility analysis of radiative TiO2+Al2O3+Cu/H2O ternary nanofluid flow over a bidirectional stretching sheet with cattaneo-christov heat flux: nanotechnology applications

Ternary nanofluids demonstrate better heat transfer characteristics in contrast to conventional liquids and typical hybrid nanofluids. These are applied in sophisticated cooling systems for electronics, heat exchangers, and automotive engines, along with renewable energy systems such as solar collectors, where efficient heat transfer plays a crucial role. The aim of this research is to investigate the movement of a Casson ternary nanofluid passing through a bidirectional exponential sheet by employing the innovative Cattaneo-Christov heat flux concept. The utilization of the energy equation considers thermal radiation, viscous dissipation, and heat source/sink effects, with the integration of chemical reaction effects into the concentration equation. An analysis of entropy generation is utilized to evaluate the thermodynamic irreversibility within the system. The conversion of transport equations involves a transformation from partial to ordinary differential equations, followed by a numerical solution utilizing the BVP4C solver embedded in the MATLAB package R2022b. The impacts of developed factors on thermal, concentration, and velocity behavior, as well as engineering quantities, are thoroughly explored graphically. The outcome reveals that the velocity gradients diminish as magnetic fields intensify, while it amplified by the Hall factor. The rise in temperature of ternary nanofluid correlates with elevated levels of radiation, and Brownian motion. Concentration intensifies with the rapid development of thermophoresis influences. Heightened values of the Reynolds and Brinkman numbers give rise to amplified entropy production but a decrease in the Bejan number. The ternary nanofluid displays a remarkable 8.92% increase in skin friction on the x-axis and y-axis, influenced by the potent Darcy-Forchheimer factor. The rates of mass and heat transfer in nanofluids undergo a decrease of 8.58% and 12.52%, respectively, due to the heightened influence of Brownian motion and Eckert number. The results could provide valuable insights into the performance of ternary nanofluids in various industrial environments under specific conditions.

Experimental analysis of the influence of PCM on the thermal behavior of lightweight buildings in different natural environments

Phase-change materials (PCM) can effectively improve the thermal performance of lightweight buildings, but their heat storage and release capacity are highly dependent on the heat exchange between the wall surface and the ambient environments. However, the current research mostly focuses on numerical simulation in a specific climate environment, and the effectiveness of PCM on the thermal regulation of lightweight buildings under a long-period natural environment is insufficient. Therefore, two experimental rooms (with and without PCM) of the same size were built and conducted in this paper to compare the changing rules of wall surface temperature, heat flux, and indoor temperature in different seasons without mechanical equipment. The results show that: (1) The effect of PCM on the thermal performance of lightweight buildings is highly correlated with seasons, and its contribution efficiency varies in different seasons; (2) The attenuation rate of the internal surface temperature in different seasons can be reduced by 18.08%–42.90 %, the delay time can be improved to 2.67–4 h compared with the reference wall; (3) PCM can effectively inhibit the fluctuation and rise of indoor temperature, which can reduce the maximum indoor temperature by 4.9–12.0 °C, increase the minimum temperature by 1.1–2.8 °C, and the thermal comfort hours added by 2–5 h; (4) Lightweight buildings incorporating PCM can saves 18.69 % and 49.63 % for the peak cooling in summer and transition seasons, and 15.9 % for the heating in winter. The research results can provide the theoretical basis and experimental support for the efficient application of PCM in lightweight buildings.

Performance evaluation of a central air conditioning system using condensate as a discharge line cooler

The energy consumption by central air conditioning (A/C) in a building is very high and efforts to reduce this energy consumption is ongoing. This study investigates the use of condensate produced by the evaporator inside the air handling unit (AHU) to cool the compressor discharge line. A central A/C with a direct expansion (DX) system and a compressor capacity of about 25 HP which uses R22 as a working fluid was used. The discharge line has a diameter of 15.9 mm wrapped with a 520 mm long heat exchanger with diameter 50 mm. The condensate produced by the AHU is passed to the heat exchanger that envelops the discharge line. The use of discharge line cooler could reduce the input power from 18.21 kW to 17.54 kW. On the other hand, the cooling capacity increased from 46.44 kW to 49.11 kW. This means that discharge cooler reduces the input power by 3.8 % and increases the cooling capacity by 5.7 %. As a result, the COP increases by 9.8 %, from 2.5 to 2.8. The method developed is not complex and only simple modification is required, thus an improvement of the performance of a central A/C system can be achieved.