Hard X-ray Absorption Spectroscopy Research Articles

Understanding improved cycling and thermal stability of compositionally graded Ni-rich layered LiNi0.6Mn0.2Co0.2O2 cathode materials

The concentration gradient is a strategic design, adjusting the distribution of Ni, typically with a higher Ni content in the core and a higher Mn content toward the surface. This design leverages the pivotal role of the Ni/Mn ratio, seeking to optimize cathode performance by balancing Ni's high capacity with Mn's stabilizing effects, particularly at the surface where degradation commonly occurs during cycling. Our study delves into the intricate structural and chemical transformations within concentration gradient cathode materials during electrochemical cycling. Utilizing advanced synchrotron X-ray techniques, including hard and soft X-ray absorption spectroscopy (hXAS, sXAS), and nanoscale X-ray imaging, we investigate buried changes in concentration gradient LiNi0.6Mn0.2Co0.2O2 (CG NMC622). Contrary to conventional assumptions, our findings challenge the notion that cycling stability relies solely on Mn stability. Unraveling the roles of Ni and Mn, we uncover how their individual and collective contributions impact the cathode's overall performance. This investigation transcends established paradigms, shedding light on the crucial mechanisms governing the enhanced cycling stability of Ni-rich layered cathode materials.

Best practices for operando hard X-ray absorption spectroscopy

Best practices for operando hard X-ray absorption spectroscopy

Improving sensitivity of XANES structural fit to the bridged metal-metal coordination.

Hard X-ray absorption spectroscopy is a valuable in situ probe for non-destructive diagnostics of metal sites. The low-energy interval of a spectrum (XANES) contains information about the metal oxidation state, ligand type, symmetry and distances in the first coordination shell but shows almost no dependency on the bridged metal-metal bond length. The higher-energy interval (EXAFS), on the contrary, is more sensitive to the coordination numbers and can decouple the contribution from distances in different coordination shells. Supervised machine-learning methods can combine information from different intervals of a spectrum; however, computational approaches for the near-edge region of the spectrum and higher energies are different. This work aims to keep all benefits of XANES and extend its sensitivity towards the interatomic distances in the first and second coordination shells. Using a binuclear bridged copper complex as a case study and cross-validation analysis as a quantitative tool it is shown that the first 170 eV above the edge are already sufficient to balance the contributions of Cu-O/N scattering and Cu-Cu scattering. As a more general outcome this work highlights the trivial but often overlooked importance of using `longer' energy intervals of XANES for structural refinement and machine-learning predictions. The first 200 eV above the absorption edge still do not require parametrization of Debye-Waller damping and can be calculated within full multiple scattering or finite difference approximations with only moderately increased computational costs.

Rare Earth Evoked Subsurface Oxygen Species in Platinum Alloy Catalysts Enable Durable Fuel Cells.

Alleviating the degradation issue of Pt based alloy catalysts, thereby simultaneously achieving high mass activity and high durability in proton exchange membrane fuel cells (PEMFCs), is highly challenging. Herein, we provide a new paradigm to address this issue via delaying the place exchange between adsorbed oxygen species and surface Pt atoms, thereby inhibiting Pt dissolution, through introducing rare earth bonded subsurface oxygen atoms. We have succeeded in introducing Gd-O dipoles into Pt3 Ni via a high temperature entropy-driven process, with direct spectral evidence attained from both soft and hard X-ray absorption spectroscopies. The higher rated power of 0.93 W cm-2 and superior current density of 562.2 mA cm-2 at 0.8 V than DOE target for heavy-duty vehicles in H2 -air mode suggest the great potential of Gd-O-Pt3 Ni towards practical application in heavy-duty transportation. Moreover, the mass activity retention (1.04 A mgPt -1 ) after 40 k cycles accelerated durability tests is even 2.4 times of the initial mass activity goal for DOE 2025 (0.44 A mgPt -1 ), due to the weakened Pt-Oads bond interaction and the delayed place exchange process, via repulsive forces between surface O atoms and those in the sublayer. This work addresses the critical roadblocks to the widespread adoption of PEMFCs.

Battery Thermalization for Operando Synchrotron Powder Diffraction: Application to the Ca-TiS2 System

Characterizing electrode materials and understanding its behavior during redox process is a key factor for battery improvement. In Situ techniques on Operando batteries are of particular interest since they do not only probe the material during the electrochemical process but avoid its hazardous and tedious extraction and transfer under inert atmosphere from an electrochemical cell to e.g. capillaries, to perform Ex Situ data collection. Synchrotron based techniques –absorption and diffraction – together with improved detectors, are now intensively used in such In Situ studies on Operando batteries since they allow fast and real time data acquisition during the electrochemical, ion (des-)insertion, process. So far most In Situ X-ray powder diffraction studies on Operando batteries are performed at room temperature using either coin cells or so called Leriche cells [1] (pouch cells, despite widely used for spectroscopy, are generally not favored for diffraction since the container material produce additional Bragg peaks). At ALBA we slightly modified both types of cells: Leriche type and more widespread used CR2032-type coin cells so as to perform data collection in temperature range -10° – 100° C. (see picture)Both types of cell have been used to study the intercalation of calcium in TiS2, previously determined by Ex Situ powder diffraction [2]. We managed to collect powder patterns operando at 60°C, 45°C and room temperature. (Des-)Insertion of solvated Ca2+ in TiS2 was favoured by temperature, its signature being the appearance of a new phase with a first diffraction peak at very low angles (~17.7 Å in terms of d-spacing). The process was found to be solvent dependent and reversible upon oxidation, which differs from Li cells where a similar process was observed.[3]Either of these thermalized cells can be used at CELLS-ALBA synchrotron for Power Diffraction on BL04-MSPD beamline or hard X-ray Absorption Spectroscopy (XANES/EXAFS) on BL22-CLEASS, and since 2023 also using simultaneous Powder Diffraction and hard X-ray Absorption Spectroscopy in BL16-NOTOS beamline. Moreover, the Leriche setup is also designed to fit for a use in laboratory X-ray diffractometers, in both reflection and transmission. Leriche et al. (2010). J. Electrochem. Soc., 157(5), A606-A610.Tchitchekova et al (2018). Chem. Mater 30, 847−856Houdeville et al. (2021). J. Electrochem. Soc., 168, 030514 Figure 1

Insights into structure and reactivity of MOFs by ambient pressure soft X-ray absorption spectroscopy

Metal–Organic Frameworks (MOFs) are nanostructured porous materials made up by metal cations and organic linkers forming three-dimensional structures. Since their discovery, the local properties of metal centers in MOFs have often been studied with hard X-ray absorption spectroscopy that is not a surface sensitive technique. Here, we employ the ambient-pressure soft X-ray absorption spectroscopy, using a newly developed experimental setup, to unveil the formation mechanism of surface defective sites in the prototypical Cu(II)-based MOF HKUST-1, as well as the reactivity and selectivity of these sites towards CO2 from the analysis of the Cu L3-edge near edge X-ray absorption spectroscopy (NEXAFS) data. We observe that, upon thermal heating, Cu(I) defects are formed more abundantly on the surface of the material as compared to the bulk, a process that is almost fully reversed when the MOF is exposed to CO2, even when mixed with H2. Additionally, we propose a structure and a formation mechanism for such defective sites, supported by theoretical DFT-based calculations.

Preferential side chain scission of polytetrafluoroethylene by bending stress

We investigated the chemical composition of polytetrafluoroethylene (PTFE) under bending stress using hard X-ray photoelectron spectroscopy and soft X-ray absorption spectroscopy. Our measurements revealed the breaking of C–F bonds in the side chains and conspicuous observation of C–C bonds in the main chain only on the surface under bending stress (carbon-rich). Moreover, we found that the breaking of C–F bonds was dependent on the tensile strain caused by bending. Investigating the effects of tensile and compressive stresses induced by bending, the tensile stress was found to significantly contribute to the breaking of C–F bonds. However, the C–F bonds were hardly broken under uniaxial tensile stress. These findings suggest that tensile stress due to bending, rather than uniaxial tensile stress, causes significant C–F bond scission in the PTFE. This result is attributed to the force acting toward the center of curvature owing to bending, which does not occur under uniaxial tensile stress. Our results provide a better understanding of microscopic PTFE surfaces subjected to flexural tensile stress for nanofluidics and medical engineering applications. Additionally, our findings suggest that carbon-rich structures can be easily fabricated, which may lead to the development of processes for fabrication of two-dimensional materials.

Phase Composition of Iron Oxide Nanoparticles Studied Using Hard X-ray Absorption Spectroscopy

At the surface of iron oxide nanoparticles, an oxidized or disordered layer is often found. Due to the large surface-to-volume ratio of nanomaterials, such a surface layer plays an important role in the overall magnetic properties of the particles. Consequently, it is important to characterize the surface layer if applications of iron oxide nanoparticles, e.g., for magnetic hyperthermia, magnetic particle imaging, or ferrofluidics, are envisaged. In this work, we tuned the phase of the surface layer of 14 nm iron oxide nanoparticles via annealing procedures. The phase composition of the particles is systematically studied using hard X-ray absorption spectroscopy.

Achieving Long-Enduring High-Voltage Oxygen Redox in P2-Structured Layered Oxide Cathodes by Eliminating Nonlattice Oxygen Redox.

Triggering reversible lattice oxygen redox (LOR) in oxide cathodes is a paradigmatic approach to overcome the capacity ceiling determined by orthodox transition-metal (TM) redox. However, the LOR reactions in P2-structured Na-layered oxides are commonly accompanied by irreversible nonlattice oxygen redox (non-LOR) and large local structural rearrangements, bringing about capacity/voltage fading and constantly evolving charge/discharge voltage curves. Herein, a novel Na0.615 Mg0.154 Ti0.154 Mn0.615 ◻0.077 O2 (◻=TM vacancies) cathode with both NaOMg and NaO◻ local configurations is deliberately designed. Intriguingly, the activating of oxygen redox at middle-voltage region (2.5-4.1V) via NaO◻ configuration helps in maintaining the high-voltage plateau from LOR (≈4.38V) and stable charge/discharge voltage curves even after 100 cycles. Hard X-ray absorption spectroscopy (hXAS), solid-state NMR, and electron paramagnetic resonance studies demonstrate that both the involvement of non-LOR at high-voltage and the structural distortions originating from Jahn-Teller distorted Mn3+ O6 at low-voltage are effectively restrained in Na0.615 Mg0.154 Ti0.154 Mn0.615 ◻0.077 O2 . Resultantly, the P2 phase is well retained in a wide electrochemical window of 1.5-4.5V (vs Na+ /Na), resulting in an extraordinary capacity retention of 95.2% after 100 cycles. This work defines an effective approach to upgrade the lifespan of Na-ion battery with reversible high-voltage capacity provided by LOR.

Stacking Order Induced Anion Redox Regulation for Layer-Structured Na0.75 Li0.2 Mn0.7 Cu0.1 O2 Cathode Materials.

Stacking order plays a key role in defining the electrochemical behavior and structural stability of layer-structured cathode materials. However, the detailed effects of stacking order on anionic redox in layer-structured cathode materials have not been investigated specifically and are still unrevealed. Herein, two layered cathodes with the same chemical formula but different stacking orders: P2-Na0.75 Li0.2 Mn0.7 Cu0.1 O2 (P2-LMC) and P3-Na0.75 Li0.2 Mn0.7 Cu0.1 O2 (P3-LMC) are compared. It is found that P3 stacking order is beneficial to improve the oxygen redox reversibility compared with P2 stacking order. By using synchrotron hard and soft X-ray absorption spectroscopies, three redox couples of Cu2+ /Cu3+ , Mn3.5+ /Mn4+ , and O2- /O- are revealed to contribute charge compensation in P3 structure simultaneously, and two redox couples of Cu2+ /Cu3+ and O2- /O- are more reversible than those in P2-LMC due to the higher electronic densities in Cu 3d and O 2p orbitals in P3-LMC. In situ X-ray diffraction reveals that P3-LMC exhibits higher structural reversibility during charge and discharge than P2-LMC, even at 5C rate. As a result, P3-LMC delivers a high reversible capacity of 190.3 mAh g-1 and capacity retention of 125.7 mAh g-1 over 100 cycles. These findings provide new insight into oxygen-redox-involved layered cathode materials for SIBs.

Redox Reaction in Ti-Mn Redox Flow Battery Studied by X-ray Absorption Spectroscopy.

We performed X-ray absorption studies for the electrolytes of a Ti-Mn redox flow battery (RFB) to understand the redox reaction of the Ti/Mn ions and formation of precipitates in charged catholyte, because suppression of the disproportionation reaction is a key to improve the cyclability of Ti-Mn RFB and enhance the energy density. Hard X-ray absorption spectroscopy with a high transmittance and soft X-ray absorption spectroscopy to directly observe the 3d orbitals were complementarily employed. Moreover, the Ti/Mn 3d electronic structure for each precipitate and solution in the charged catholyte was investigated by using scanning transmission X-ray microscopy: the valence of Mn in the precipitate is mostly attributed to 4+, and the solution includes only Mn2+ . This charge disproportionation reaction should occur after the Mn ions in the catholyte should be oxidized from Mn2+ to Mn3+ by charge.

Nanometer-scale depth-resolved hard x-ray absorption spectroscopy based on the detection of energy-loss Auger electrons with low energies

X-ray absorption spectroscopy (XAS) provides information on the chemical state and atomic structure of a target element even without long-range periodicity. A depth-resolved surface-sensitive XAS method for K-edge using hard x rays is proposed herein. The principle of this method is based on the selective detection of low-energy electrons using an electron analyzer. The detected electrons originate from the LMM Auger electrons that cascade from the KLL Auger process caused by K-shell absorption and lose the energy corresponding to their travel distance in a solid. The analysis depth was confirmed to be in the nanometer range using a GaN substrate with a thin oxide film of the defined thickness. In addition, depth-resolved information regarding the local atomic structure, including the interatomic distance and crystallinity, was obtained via the Fourier transformation of the spectral oscillations. Because the proposed technique does not require a change in the detection angle, it is also expected to be used for particles and samples with uneven surfaces.

Stability of Metal Hydroxide Organic Frameworks for Oxygen Evolution

The oxygen evolution reaction (OER) is central to storing electrical energy via chemical bonds in energy carriers and fuels through reactions such as electrochemical water splitting to produce hydrogen, CO2 reduction for CO and liquid hydrocarbons, and nitrogen to ammonia. While there has been considerable work towards the engineering of inexpensive yet highly active OER catalysts, current state-of-the-art materials are still at least an order of magnitude less active than oxygen evolving complexes found in biological systems that intricately combine inorganic metal-oxo clusters with organic ligands.1 As a result, metal organic frameworks (MOFs) have drawn considerable attention as hybrid organic-inorganic systems that can potentially mimic the unique structure of biological oxygen evolving complexes. Recently, metal hydroxide organic frameworks (MHOFs),2 a new class of MOFs that combine layered hydroxides with aromatic carboxylate linkers that stabilize the structure via π-π interactions, have been shown to display three times the tunability of layered hydroxides, offering extensive opportunities for further engineering of its electrochemical properties for numerous applications. However, the long-term stability of these material during OER is still unclear, which would be paramount to understand for further rational design of this class of material.In this study, we investigated Ni-based MHOFs with carboxylate linkers of varying π-π interaction strengths to understand how these differences affect the electrochemical stability of these materials during OER. We observed that the MHOFs all undergo activation during OER leading to two orders of magnitude increase in OER activity, where the MHOFs with weaker π-π interaction strengths tend to transform at a faster rate than the MHOFs with stronger π-π interaction strengths. We further characterized the MHOFs using a wide range of analytical techniques, including scanning transmission electron microscopy, Raman spectroscopy, x-ray photoelectron spectroscopy, and hard x-ray absorption spectroscopy, before and after extended OER cycling and galvanostatic tests to understand the transformed phase, which suggested that while the bulk structure largely remains unchanged, the surface undergoes significant restructuring into a Ni(OH)2-like phase during OER. Using operando UV-vis and Raman spectroscopy measurements on the MHOFs during OER to understand the factors that induce the transformation process, we found that there was a clear link between the Ni2+/3+, 4+ redox couple observed around 1.4 VRHE and a loss in the carboxylate organic linkers for the linkers with weak π-π interactions. However, for the MHOFs synthesized with linkers exhibiting strong π-π interaction strengths, there were smaller changes to the overall material during OER, suggesting that the bulk stability of these materials is largely dictated by the linker interaction strength and activation are primarily only surface transformations. These results directly demonstrate that linker selection also plays a key role in the stability MOFs under electrochemical conditions and are pertinent for rational design and understanding of the stability and activity of hybrid organic-inorganic materials as electrocatalysts.

(Digital Presentation) Regulating Anion Redox during Cycling of Spinel LiMn1.5Ni0.5O4 As Cathodes for Lithium Ion Batteries

In recent years, extensive research has been performed on high energy cathode materials for lithium ion batteries being used in electric vehicles to reduce carbon emissions. Compared to the commercial layered cathode materials, the absence of cobalt in the spinel LiMn1.5Ni0.5O4 (LMNO) makes this material more environmentally friendly and cheaper.1 Spinel LMNO cathodes also reveal attractive gravimetric and volumetric energy densities of 635Whkg−1 and 2820WhL−1, respectively.2 According to the distribution of transition metals (TM) within the cubic crystal structure, spinel LMNO can be categorized into either ordered or disordered. Normally, disordered LMNO materials are produced at temperatures higher than the theoretical oxygen release temperature of spinel LMNO (715 °C).3 The formation of O vacancies is accompanied by some Mn4+ atoms being reduced to Mn3+ to maintain the electroneutrality of spinel LMNO. Ordered LMNO can be obtained through calcination at temperatures lower than 715 °C or post-annealing disordered LMNO materials at 700 °C.4 The reversible extraction and insertion of O atoms accompanied with different distribution of TM during spinel LMNO preparation drive up a hypothesis that the oxygen activity during cycling of spinel LMNO may be affected by the distribution of TM atoms, especially since the operating voltage of spinel LMNO (> 4.7 V) is high enough to trigger oxygen redox in other lithium transition metal oxides.5 To explore the feasibility of oxygen activity during cycling of spinel LMNO, the normal, core-shell and sandwich designed synthesis are performed using special Mn0.75Ni0.25(OH)2 precursors to arrange different distributions of TM atoms in the obtained N-, CS- and SW-LMNO. As shown in Figure 1(a) – (c), the three materials show similar XRD patterns in the pristine state, yet different reflection peaks are observed in the three materials after charging to 4.9 V. The unclear phase transition of SW-LMNO indicates it show stable structure. The three materials also show different CV curves, see Figure 1(d). This indicates the extraction and insertion of Li atoms lead to different redox reactions in the three materials. Besides, differential electrochemical mass spectrometry (DEMS), in-situ transmission electron microscope (TEM) as well as hard and soft X-ray absorption spectroscopy (XAS) measurements are utilized to further investigate the oxygen activity during cycling of spinel LMNO.Reference1. Li, M. & Lu, J. Cobalt in lithium-ion batteries. Science 367, 979-980 (2020).2. Hagh, N. M. & Amatucci, G. G. A new solid-state process for synthesis of LiMn1. 5Ni0. 5O4−δ spinel. Journal of Power Sources 195, 5005-5012 (2010).3. Manthiram, A., Chemelewski, K. & Lee, E.-S. A perspective on the high-voltage LiMn1.5Ni0.5O4 spinel cathode for lithium-ion batteries. Energy & Environmental Science 7, 1339-1350 (2014).4. Chemelewski, K. R., Shin, D. W., Li, W. & Manthiram, A. Octahedral and truncated high-voltage spinel cathodes: the role of morphology and surface planes in electrochemical properties. Journal of Materials Chemistry A 1, 3347-3354 (2013).5. Seo, D.-H. et al. The structural and chemical origin of the oxygen redox activity in layered and cation-disordered Li-excess cathode materials. Nature chemistry 8, 692-697 (2016).Figure 1. Operando X-ray diffraction patterns of N- (a), CS- (b) and SW- (c) LiMn1.5Ni0.5O4 in the pristine states and at the charge states of 4.9 V and the corresponding cyclic voltammetry curves of the three materials (d) Figure 1

Low thermal-expansion and high proton uptake for protonic ceramic fuel cell cathode

Nowadays, the excessive thermal expansion behavior of Co-based electrode always leads to the cell degradation or delamination. Especially for BaCoO3-δ-type perovskite oxides, as the result of the large ionic radius of Ba2+ (1.61 Å), the phase structures of these materials are not stable. Herein, we developed a novel single-phase electrode Ba2Sc0.1Nb0.1Co1.5Fe0.3O6-δ (BSNCF) with a stable cubic perovskite structure and suitable thermal expansion coefficient (TEC, 11.9 × 10−6 K−1), which showed a great stability in symmetrical cell area specific resistances (ASRs) subjecting to the harsh thermal cycling procedure with 30 cycles between 300 °C and 600 °C (increased from 0.197 Ω cm2 to 0.222 Ω cm2,13% increase). The high-temperature hard X-ray absorption spectroscopy measurement directly monitored a small change of Co valence in BSNCF as the temperatures rising. Also, BSNCF exhibits well proton uptake for its appropriate oxygen-site basicity and excellent surface reaction activity. The single cell based on BSNCF achieved an outstanding peak power density of 977 mW cm−2 at 600 °C.

Quantification of Adsorbates by X-ray Absorption Spectroscopy: Getting TGA-like Information for Free.

Hard X-ray absorption spectroscopy (XAS) is frequently applied in catalysis and gas sorption studies to monitor changes in oxidation states, coordination numbers, and interatomic distances of active sites under in situ and operando conditions. However, transmission XAS data can reveal also the change in the total amount of guest species adsorbed on the whole sample. Surprisingly, to the best of our knowledge, the latter property has never been exploited. Here, we present a simple method to quantify the amount of adsorbates from XAS data collected during the interaction of the sample with gases or liquids. The method relies on monitoring the change of the total absorption level below the measured absorption edge and does not require any additional instrumentation or modification of the XAS data collection procedure. Essentially, it is a way to obtain the information analogous to the one delivered by temperature-programmed reduction (TPR), temperature-programmed desorption (TPD), or thermogravimetric analysis (TGA) directly from XAS at no extra cost.

Dynamical investigation of tunable magnetism in Au@Ni-carbide nanocrystals by a combined soft and hard X-ray absorption spectroscopy

Dynamical investigation of tunable magnetism in Au@Ni-carbide nanocrystals by a combined soft and hard X-ray absorption spectroscopy

Precisely quantifying bulk transition metal valence evolution in conventional battery electrode by inverse partial fluorescence yield

Precisely quantifying transition metal (TM) redox in bulk is a key to understand the fundamental of optimizing cathode materials in secondary batteries. At present, the commonly used methods to probe TM redox are hard X-ray absorption spectroscopy (hXAS) and soft X-ray absorption spectroscopy (sXAS). However, they are both facing challenges to precisely quantify the valence states of some transition metals such as Mn. In this paper, Mn-L iPFY (inverse partial fluorescence yield) spectra extracted from Mn-L mRIXS (mapping of resonant inelastic X-ray scattering) is adopted to quantify Mn valence states. Mn-L iPFY spectra has been considered as a bulk-sensitive, non-distorted probe of TM valence states. However, the exact precision of this method is still unclear in quantifying practical battery electrodes. Herein, a series of LiMn2O4 electrodes with different charge and discharge states are prepared. Based on their electrochemical capacity (generally considered to be very precise), the precision of Mn iPFY in quantifying bulk Mn valence state is confirmed, and the error range is unraveled. Mn-L mRIXS iPFY thus is identified as one of the best methods to quantify the bulk Mn valence state comparing with hXAS and sXAS.

Comprehensive investigation of crystallographic, spin-electronic and magnetic structure of [formula omitted]: Unraveling the suppression of configuration entropy in high entropy oxides

High entropy oxides (HEOs) are a rapidly emerging class of functional materials consisting of multiple principal cations. The original paradigm of HEOs assumes cationic occupations with the highest possible configurational entropy allowed by the composition and crystallographic structure. However, the fundamental question remains on the actual degree of configurational disorder in HEOs, especially, in systems with low enthalpy barriers for cation anti-site mixing. Considering the experimental limitations due to the presence of multiple principal cations in HEOs, here we utilize a robust and cross-referenced characterization approach using soft X-ray magnetic circular dichroism, hard X-ray absorption spectroscopy, Mössbauer spectroscopy, neutron powder diffraction and SQUID magnetometry to study the competition between crystal field stabilization energy and configurational entropy governing the cation occupation in a spinel HEO (S-HEO), (Co0.2Cr0.2Fe0.2Mn0.2Ni0.2)3O4. In contrast to the previous studies, the derived complete structural and spin-electronic model, (Co0.6Fe0.4)(Cr0.3Fe0.1Mn0.3Ni0.3)2O4, highlights a significant deviation from the hitherto assumed paradigm of entropy-driven non-preferential distribution of cations in HEOs. An immediate correlation of this result can be drawn with bulk as well as the local element specific magnetic properties, which are intrinsically dictated by cationic occupations in spinels. The real local lattice picture presented here provides an alternate viewpoint on ionic arrangement in HEOs, which is of fundamental interest for predicting and designing their structure-dependent functionalities.

Oxygen-Vacancy-Driven Orbital Reconstruction at the Surface of TiO2 Core-Shell Nanostructures.

Oxygen vacancies and their correlation with the electronic structure are crucial to understanding the functionality of TiO2 nanocrystals in material design applications. Here, we report spectroscopic investigations of the electronic structure of anatase TiO2 nanocrystals by employing hard and soft X-ray absorption spectroscopy measurements along with the corresponding model calculations. We show that the oxygen vacancies significantly transform the Ti local symmetry by modulating the covalency of titanium-oxygen bonds. Our results suggest that the altered Ti local symmetry is similar to the C3v, which implies that the Ti exists in two local symmetries (D2d and C3v) at the surface. The findings also indicate that the Ti distortion is a short-range order effect and presumably confined up to the second nearest neighbors. Such distortions modulate the electronic structure and provide a promising approach to structural design of the TiO2 nanocrystals.