Hydroxyl Research Articles

Non-classical Deactivation Mechanism in a Supported Intermetallic Catalyst for Propane Dehydrogenation.

Platinum-based supported intermetallic alloys (IMAs) demonstrate exceptional performance in catalytic propane dehydrogenation (PDH) primarily because of their remarkable resistance to coke formation. However, these IMAs still encounter a significant hurdle in the form of catalyst deactivation. Understanding the complex deactivation mechanism of supported IMAs, which goes beyond conventional coke deposition, requires meticulous microscopic structural elucidation. In this study, we unravel a nonclassical deactivation mechanism over a PtZn/γ-Al2O3 PDH catalyst, dictated by the PtZn to Pt3Zn nanophase transformation accompanied with dezincification. The physical origin lies in the metal support interaction (MSI) that enables strong chemical bonding between hydroxyl groups on the support and Zn sites on the PtZn phase to selectively remove Zn species followed by the reconstruction towards Pt3Zn phase. Building on these insights, we have devised a solution to circumvent the deactivation by passivating the MSI through surface modification of γ-Al2O3 support. By exchanging protons of hydroxyl groups with potassium ions (K) on the γ-Al2O3 support, such a strategy significantly minimizes the dezincification of PtZn IMA via diminished metal-support bonding, which dramatically reduces the deactivation rate from 0.2044 to 0.0587 h-1.

Microwave-Assisted Synthesis of β-N-Aryl Glycoamphiphiles with Diverse Supramolecular Assemblies and Lectin Accessibility.

Glycoamphiphiles have attracted considerable interest in a broad range of application fields owing to their solution and bulk-state self-assembly abilities. Despite their importance, the straightforward synthesis of glycoamphiphiles consisting of a hydrophilic carbohydrate linked to a hydrophobic aglycone remains one of the major challenges in glycosciences. Here, a rapid, simple, and efficient synthetic access to chemically stable glycoamphiphiles at physiological pH, namely, N-(β-d-glycosyl)-2-alkylbenzamide, is reported. It leverages the nonreductive amination of unprotected carbohydrates with ortho-substituted aniline derivatives which could be readily obtained by reacting commercially available primary alkylamines with isatoic anhydride. This strategy avoids protection and deprotection of sugar hydroxyl groups and the use of reductive agents, which makes it advantageous in terms of atom and step economy. Moreover, in order to circumvent the cons of classical N-aryl glycosylation, we investigate the use of microwave as a heat source that provides fast, clean, and high-yield β-N-arylation of unprotected carbohydrates. Their self-assembly into water led to multiple morphologies of dynamic supramolecular glycoamphiphiles that were characterized to assess their ability to bind to lectins from pathogenic bacteria. Biophysical interactions probed by isothermal titration microcalorimetry revealed micromolar affinities for most of the synthesized glycoamphiphiles.

The quassinoids bruceines A-M: pharmacology, mechanism of action, synthetic advance, and pharmacokinetics-a review.

Bruceines A-L are among the quassinoid representatives found in the medicinal plant Brucea javanica (L.). An overview of their pharmacological activities is still unknown. The given research deals with highlights in their pharmacological result, molecular mechanism of action, synthetic progress, and pharmacokinetics. From previous evidence, bruceine derivatives are potential agents for anticancer treatments, as well as they are appropriate to treat inflammation, diabetes, and parasitic infections, and protect the neurons, kidneys, and lungs. Cytokine inhibitions, oxidative stress responses, and various signaling pathways, such as MAPK (mitogen-activated protein kinase) and NF-κB (nuclear factor-kappa B), have been proposed as the underlying mechanisms of action. Synthetic approaches to synthesize new derivatives with enhancement activities are based on free hydroxyl group modifications. Bruceines seem to be promptly absorbed by both oral and intravenous administrations, but their bioavailability is not high (less than 6%). Pre-clinical and clinical studies to prove their anticancer potential and other activities are urgent. Structural modifications, nano-combinations, and synergistic effects are necessary.

Desulfurization of Thiols for Nucleophilic Substitution.

Although the desulfurization of thiols is a topic of great importance and has received significant attention, most efforts have focused on the hydrodesulfurization of thiols. In this work, we describe the desulfurization of thiols for nucleophilic substitution. This process occurs rapidly, promoted by the Ph3P/ICH2CH2I system, and can be extended to a wide range of nucleophiles. Notably, free amines can be employed as nucleophiles to synthesize various secondary and tertiary amines. This method tolerates a wide array of functional groups, including hydroxyl groups in amination reactions. Benzyl thiols are particularly reactive and can be completely converted at room temperature within 15 min. Although alkyl thiols show lower reactivity, they can also be converted smoothly at a reaction temperature of 70 °C overnight.

Enhanced Photocatalytic Ozonation Using ModifiedTiO2 withDesignedNucleophilic and Electrophilic Sites.

Photocatalytic ozonation is considered to be a promising approach for the treatment of refractory organic pollutants, but the design of efficient catalyst remains a challenge. Surface modification provides a potential strategy to improve the activity of photocatalytic ozonation. In this work, density functional theory (DFT) calculations were first performed to check the interaction between O3 and TiO2-OH (surface hydroxylated TiO2) or TiO2-F (surface fluorinated TiO2), and the results suggest that TiO2-OH displays better O3 adsorption and activation than does TiO2-F, which is confirmed by experimental results. The surface hydroxyl groups greatly promote the O3 activation, which is beneficial for the generation of reactive oxygen species (ROS). Importantly, TiO2-OH displays better performance towards pollutants (such as berberine hydrochloride) removal than does TiO2-F and most reported ozonation photocatalysts. The total organic carbon (TOC) removal efficiency reaches 84.4% within two hours. This work highlights the effect of surface hydroxylation on photocatalytic ozonation and provides ideas for the design of efficient photocatalytic ozonation catalysts.

Chemoenzymatic Synthesis of Fluorinated Mycocyclosin Enabled by the Engineered Cytochrome P450-Catalyzed Biaryl Coupling Reaction.

Installing fluorine atoms onto natural products holds great promise for the generation of fluorinated molecules with improved or novel pharmacological properties. The enzymatic oxidative carbon-carbon coupling reaction represents a straightforward strategy for synthesizing biaryl architectures, but the exploration of this method for producing fluorine-substituted derivatives of natural products remains elusive. Here, in this study, we report the protein engineering of cytochrome P450 from Mycobacterium tuberculosis (MtCYP121) for the construction of a series of new-to-nature fluorine-substituted Mycocyclosin derivatives. This protocol takes advantage of a "hybrid" chemoenzymatic procedure consisting of tyrosine phenol lyase-catalyzed fluorotyrosine preparation from commercially available fluorophenols, intermolecular chemical condensation to give cyclodityrosines, and an engineered MtCYP121-catalyzed intramolecular biphenol coupling reaction to complete the strained macrocyclic structure. Computational mechanistic studies reveal that MtCYP121 employs Cpd I to abstract a hydrogen atom from the proximal phenolic hydroxyl group of the substrate to trigger the reaction. Then, conformational change makes the two phenolic hydroxyl groups close enough to undergo intramolecular hydrogen atom transfer with the assistance of a pocket water molecule. The final diradical coupling process completes the intramolecular C-C bond formation. The efficiency of the biaryl coupling reaction was found to be influenced by various fluorine substitutions, primarily due to the presence of distinct binding conformations.

Comparative performance analysis of mussel-inspired polydopamine, polynorepinephrine, and poly-α-methyl norepinephrine in electrochemical biosensors.

Polydopamine (PDA) has garnered significant interest for applications in biosensors, drug delivery, and tissue engineering. However, similar polycatecholamines like polynorepinephrine (PNE) with additional hydroxyl groups and poly-α-methylnorepinephrine (PAMN) with additional hydroxyl and methyl groups remain unexplored in the biosensing domain. This research introduces three innovative biosensing platforms composed of ternary nanocomposite based on reduced graphene oxide (RGO), gold nanoparticles(Au NPs), and three sister polycatecholamine compounds (PDA, PNE, and PAMN). The study compares and evaluates the performance of the three biosensing systems for the ultrasensitive detection of Mycobacterium tuberculosis (MTB). The formation of the nanocomposites was meticulously examined through UV-Visible, Raman, XRD, and FT-IR studies with FE-SEM and HR-TEM analysis. Cyclic voltammetry and differential pulse voltammetry measurements were also performed to determine the electrochemical characteristics of the modified electrodes. Electrochemical biosensing experiments reveal that the RGO-PDA-Au, RGO-PNE-Au, and RGO-PAMN-Au-based biosensors detected target DNA up to a broad detection range of 0.1 × 10-8 to 0.1 × 10-18M, with a low detection limit (LOD) of 0.1 × 10-18, 0.1 × 10-16, and 0.1 × 10-17M, respectively. The bioelectrodes were proved to be highly selective with excellent sensitivities of 3.62 × 10-4mAM-1 (PDA), 7.08 × 10-4mAM-1 (PNE), and 6.03 × 10-4mAM-1 (PAMN). This study pioneers the exploration of two novel mussel-inspired polycatecholamines in biosensors, opening avenues for functional nanocoatings that could drive further advancements in this field.

Revealing elusive conformations of sucrose from hydrogen bond J-coupling in H2O: A combined NMR and quantum mechanics study.

Hydrogen bonding is a crucial feature of biomolecules, but its characterization in glycans dissolved in aqueous solutions is challenging due to rapid hydrogen exchange between hydroxyl groups and H2O. In principle, the scalar (J) coupling constant can reveal the relative orientation of the atoms in the molecule. In contrast to J-coupling through H-bonds reported in proteins and nucleic acids, research on J-coupling through H-bonds in glycans dissolved in water is lacking. Here, we use sucrose as a model system for H-bonding studies; its structure, which consists of glucose (Glc) and fructose (Frc), is well-studied, and it is readily available. We apply the in-phase, antiphase-HSQC-TOCSY and quantify previously unreported through H-bond J-values for Frc-OH1-Glc-OH2 in H2O. While earlier reports of Brown and Levy indicate this H-bond as having only a single direction, our reported findings indicate the potential presence of two involving these same atoms, namely, G2OH➔F1O and F1OH➔G2O (where F and G stand for Frc and Glc, respectively). The calculated density functional theory J-values for the G2OH➔F1O agree with the experimental values. Additionally, we detected four other possible H-bonds in sucrose, which require different phi, psi (ϕ, ψ) torsion angles. The ϕ, ψ values are consistent with previous predictions of du Penhoat et al. and Venable et al. Our results will provide new insights into the molecular structure of sucrose and its interactions with proteins.

Tuning the electronic properties of reduced bilayer graphene oxide: controllable flat bands and improved conductivity

Going beyond conventional doping techniques, this work explores the interesting phenomenon of flat bands in single and double layer graphene induced by functionalization with epoxy and hydroxyl groups. We show that these flat bands, located near the Fermi level, provide a new level of control over electronic properties, influencing conductivity and potentially allowing bandgap manipulation. In particular, in bilayer structures we discover a remarkable asymmetry in flat band formation, where less distorted layers exhibit flatter bands and dominate the electronic landscape. Furthermore, the presence of hydrogen bonding in bilayer systems leads to a lower flat band energy, which has promising implications for stability. This work opens new avenues for designing next-generation electronic devices with engineered functionalities by harnessing the power of flat band engineering in functionalized graphene.

Nuclear quantum effects in gas-phase ethylene glycol.

Path integral molecular simulations are used to explore the nuclear quantum effects (NQEs) on the structure, dihedral landscape and infrared spectrum of ethylene glycol. The simulations are carried out on a new reaction surface Hamiltonian-based model potential energy surface, with special focus on the role of the OCCO and HOCC dihedrals. In contrast with classical simulations, we analyse how the intramolecular interactions between the OH groups change due to zero-point effects as well as temperature. These are found to be weak. The NQEs on the free energy profile along the OCCO dihedral are analysed, where notable effects are seen at low temperatures and found to be correlated with the radii of gyration of the atoms. Finally, the power spectrum of the molecule from path integral simulations is compared with the experimental infrared spectrum, yielding a good agreement of band positions.

Alkanols Regulate the Fluidity of Phospholipid Bilayer in Accordance to Their Concentration and Polarity.

In spite of the widespread use of alkanols as penetration enhancers, their effect on vesicular formulations remains largely unexplored. These can affect the stability and integrity of the phospholipid bilayers. In this study, we have investigated the interaction of linear (ethanol, butanol, hexanol, octanol) and branched alkanols (t-amylol and t-butanol) with three phospholipids (soya lecithin, SL; soy L-α-phosphatidylcholine, SPC; and 1,2-dipalmitoyl-sn-glycero-3-phosphocholine, DPPC). Thermodynamic and structural aspects of these interactions were studied as a function of the alkanol concentration and chain length. Our interpretations are based on isothermal titration calorimetry (ITC) and dynamic light scattering (DLS) experiments. We observed one-site interactions wherein hydroxyl and acyl groups interacted with the polar and nonpolar regions of the phospholipid, respectively. The stability and structural integrity of bilayers appeared to be dependent upon (a) the hydrocarbon chain length and concentration of alcohols, and (b) the degree of unsaturation in the phospholipid molecule. We found that these interactions triggered a reduction in the enthalpy which was compensated by increased entropy, keeping free energy negative. Drop in enthalpy indicates reversible disordering of the bilayer which enables the diffusion of alcohol without triggering destabilization. Ethanol engaged predominantly with the interface, and it resulted in higher enthalpic changes. Interactions became increasingly unfavorable with longer alcohols - a cutoff point was recorded with hexanol. The overall sequence of membrane disordering capability was recorded as follows: ethanol < butanol < octanol < hexanol. Octanol's larger size restricted its penetration in the bilayer, and hence it caused less enthalpic changes relative to hexanol. This could also be verified from the trends in the area ratio of these vesicles obtained from the DLS data. Branched alkanols displayed a lower binding affinity with the phospholipids relative to their linear counterparts. These data are useful while contemplating the inclusion of short-chain alcohols as penetration enhancers in phospholipid vesicles.

Characterization of Exopolysaccharides Having Potential Antiviral Properties from Priestia Aryabattai Strain MK1 and Bacillus sp. Strain MK2.

Viral diseases are a serious threat to humans while themost antiviral drugs have low efficiency and side effects on human health. Therefore, using microbial biopolymers as the drugs alternate to treat viral infections seems cost-effective and human friendly option. In the present study, thirty-four exopolysaccharides (EPSs) producing bacteria were isolated, and EPSs production capacity of five salt-tolerant isolates was determined under 0, 100 and 150 mM NaCl. Among these, two isolates exhibiting high anti-coliphage activity were identified through 16S rRNA gene analysis. Moreover, the EPSs were characterized by Fourier-transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) analysis, and their composition was determined. Five salt-tolerant bacteria (MK1, MK2, MK10, MK22 and MK29) exhibited higher production of EPSs at 100 mM NaCl compared to that under non-saline control. At 100 mM NaCl, the yield of EPSs ranged between 105 and 330mg 100 mL-1 broth. The EPSs produced by the isolates MK1 and MK2 exhibited higher anti-coliphage activity (plaque forming unit decreased from 43 × 106 mL-1 to 3 × 106 and 4 × 106 mL-1, respectively), and were comprised of glucose, fructose, galactose, sucrose, lactose and xylose sugars. FTIR spectroscopy depicted that EPSs are mainly composed of hydroxyl, aliphatic, carboxyl, sulfate and phosphate functional groups, which could have bound coliphage and thus conferred higher anti-coliphage activities to the EPSs. Phylogenetic analysis revealed that MK1 and MK2 isolates formed clades within genus Priestia and Bacillus sequences, respectively. High EPSs production capacity of bacterial isolates under saline condition and high anti-coliphage activity of the EPSs implies that bacterial biopolymers could be useful in antiviral drugs therapy.

A thermodynamic model of the surface hydroxylation of γ-Al2O3.

Rational design of γ-alumina-based catalysts relies on an extensive understanding of the distribution of hydroxyl groups on the surface of γ-alumina and their physicochemical properties, which remain unclear and challenging to determine experimentally due to the structural complexity. In this work, by means of DFT and thermodynamic calculations, various hydroxylation modes of γ-alumina (110) and (100) surfaces at different OH coverages were evaluated, based on which a thermodynamic model to reflect the relationship between temperature and the surface structure was established and the stable hydroxylation modes under experimental conditions were predicted. This enables us to identify the experimentally measured IR spectra. The effect of hydroxyl coverages on the surface Lewis acidity was then analyzed, showing that the presence of hydroxyl groups could promote the Lewis acidity of neighboring Al sites. This work provides fundamental insights into the molecular level understanding of the surface properties of γ-alumina and benefits the rational design of alumina-based catalysts.

One step production from the monomer of poly(L‐lactide)/flax biocomposites by thermoplastic resin transfer molding: Mechanical properties and aging

AbstractDevelopment of biocomposites is becoming a necessity due to environmental concerns. Polylactide is a matrix of choice, regarding its bio‐sourced and compostable nature along with its mechanical properties. In this study, poly(L‐lactide)/flax biocomposites were produced using thermoplastic resin transfer molding (TP‐RTM) in one step process from the monomer, affording sustainable and fully compostable composite materials. The polymerization of L‐lactide (L‐LA) monomer was promoted by tin octoate, affording poly(L‐lactide) (PLLA) matrices displaying monomer conversions superior to 96% and mass‐average molar masses above 140,000 g/mol. Flax fibers were used as received without any functionalization which is usually conducted to prevent the hydroxyl groups to conduct side reactions. Mechanical testing revealed bending modulus of 9.3 GPa and bending strength of 177 MPa comparable to existing literature values for PLLA/flax composites produced by other techniques. Digital microscopy analysis provided insights into impregnation quality and void characterization within the composites. In addition, the durability of these biocomposites was also evaluated via accelerated aging tests.Highlights PLLA/flax biocomposites were produced by TP‐RTM for the first time. In situ polymerization of the PLLA matrix associated with non‐functionalized flax fabrics was conducted. Bending properties were found in line with those of PLLA/flax composites produced by compression molding. Aging tests under UV at 50°C of PLLA/flax biocomposites were conducted.

Two-Dimensional Cu-Based MOF for Selective Staining of the Cellular Nucleus through Fluorescence Imaging and Selective Sorption of Dye Molecules in Aqueous Medium.

A two-dimensional copper-based metal-organic framework, [Cu(C23H14O6)(C10H8N2)2]·H2O·DMSO, 1, was synthesized using pamoic acid (C23H16O6) and 4,4'-bipyridine (C10H8N2) as an organic ligand and Cu(II) as a metal ion. Single-crystal structure X-ray diffraction studies of the as-synthesized compound showed a two- dimensional structure with free hydroxyl groups. Upon excitation at 370 nm, the aqueous dispersion of [Cu(C23H14O6)(C10H8N2)2]·H2O·DMSO, 1, showed emission centered at 525 nm resulting from the intraligand energy transfer. Fluorescence microscopic experiments using a human epithelioid cervix carcinoma HeLa cell line were carried out, clearly showing that our compound selectively stained the cellular nucleus. To utilize the porous nature of [Cu(C23H14O6)(C10H8N2)2]·H2O·DMSO, 1, its dye sorption behavior in aqueous solution was determined, and a high affinity for methylene blue (MB) dye was confirmed. Our synthesized compound sorbed 88% MB dye with an initial concentration of 32 mg L-1, and its sorption capacity for MB was found to be 29.79 mg g-1. The possible mechanism of the dye sorption behavior was discussed in terms of the size and charge of dye molecules with respect to molecular-level interactions between the framework and the dye molecules.

The Synergetic Reduction of the Condensation Degree of Dissolved Lignin (DL) during the Refining Process of Wheat Straw Biomass Based on the MA/O3 System

Lignin, a natural pol2ymer with a complex structure that is difficult to separate, is prone to C-C bond condensation during the separation process. To reduce the condensation of lignin, here, a novel method is proposed for separating the components by using a combination of maleic acid (MA)/ozone (O3) to co-treat wheat straw. The removal of lignin, glucan, and xylan was 38.07 ± 0.2%, 31.44 ± 0.1%, and 71.98 ± 0.1%, respectively, under the conditions of ball-milling of wheat straw for 6 h, reaction temperature of 60 °C, and O3 holding time of 9 min. Lignin-rich solutions were collected to extract the dissolved lignin (DL) after washing the treated samples. The DL obtained under MA/O3 conditions had a carboxyl group (-COOH) content of 2.96 mmol/g. The carboxyl group of MA underwent esterification with the hydroxyl group (-OH) at the γ position of lignin and O3 reacted on the positions of the lignin side chain or the phenolic ring, resulting in a break in the side chain and the opening of the phenolic ring to introduce the carboxyl group. The 2D-HSQC-NMR results revealed that the phenolic ring-opening reaction of lignin in the presence of O3 was essentially free of β-β and β-5 condensation bonds.

Supercritical hydrothermal synthesis of ultra-fine Cu powders

ABSTRACT Ultra-fine Cu powders were synthesized using supercritical water as a reaction medium and formic acid as a reducing agent. The effects of reducing agent, reaction temperature, and complexing agent on the phase constituents, particle size distributions and morphology of the synthesized ultra-fine Cu powders were investigated. A complex mixture of Cu2O and Cu powders formed by pure supercritical water while high purity homogeneous ultra-fine Cu powders can be synthesized by supercritical water with formic acid as a reducing agent. Moreover, fine tuning of particle size and morphology can be realized by the addition of Ethylenediamine tetraacetic acid (EDTA). The modification mechanism of EDTA on the surfaces of ultra-fine Cu powders was investigated by X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. EDTA adsorbed on the surfaces of nanoparticles by the dehydration reaction of carboxyl groups in the molecule of EDTA and hydroxyl groups on surfaces of copper nanoparticles (CuOH).

Unexpected Self-Assembly of Nanographene Oxide Membranes upon Electron Beam Irradiation for Ultrafast Ion Sieving.

Nanographene oxide (nGO) flakes-graphene oxide with a lateral size of ≈100nm or less-hold great promise for superior flux and energy-efficient nanofiltration membranes for desalination and precise ionic sieving owing to their unique high-density water channels with less tortuousness. However, their potential usage is currently limited by several challenges, including the tricky self-assembly of nano-sized flakes on substrates with micron-sized pores, severe swelling in aqueous solutions, and mechanical instability. Herein, the successful fabrication of a robust membrane stacked with nGO flakes on a substrate with a pore size of 0.22µm by vacuum filtration is reported. This membrane achieved an unprecedented water permeance above 819.1 LMH bar-1, with a high rejection rate of 99.7% for multivalent metal ions. The nGO flakes prepared using an electron beam irradiation method, have uniquely pure hydroxyl groups and abundant aromatic regions. The calculations revealed the strong hydrogen bonds between two nGO flakes, which arise from hydroxyl groups, coupled with hydrophobic aromatic regions, greatly enhance the stability of stacked flakes in aqueous solutions and increase their effective lateral size. The research presents a simple yet effective approach toward the fabrication of advanced 2D nanographene membranes with superior performance for ion sieving applications.

Coaxial-Tube Quantitative Nuclear Magnetic Resonance for Various Solutions Using SI-Traceable Concentration References.

Quantitative nuclear magnetic resonance (qNMR) is an accepted method for determining analyte concentrations using quantitative substances in one spectrum. Conventional qNMR is performed using a mixture of analytes and reference substances. In coaxial-tube NMR, two tubes are used as different solutions, similar to normal NMR spectra. Currently, coaxial tubes with various diameters are available; however, coaxial-tube qNMR is limited, and a general analytical protocol is yet to be proposed. In this study, we established an effective volume ratio (EVR) measurement method using the weight density and qNMR methods. Various analyte concentrations were determined using coaxial-tube qNMR and an SI-traceable reagent. The EVR required for the qNMR concentration calculation was determined using a coefficient of variation (CV) of <1% for an inner tube of ϕ 3 mm or less. The peak integral of each substance was correlated with the effective volume, depending on the abundance of the tube and matched 1H in the solution. The T1 relaxation times differed depending on the substructure, and the T1 values of the formate and OH groups varied for each tube set. Thus, each partial structural characteristic of the peak must be understood before qNMR is performed. The concentrations of various substances, including hygroscopic substances, were determined using coaxial-tube qNMR. Coaxial tubes eliminate the need to mix the analyte with the reference substance; thus, we can quantify the analyte without causing pH and structural changes caused by other mixtures and reuse the analyte for other test systems.

Screening Potential Nitrification Inhibitors through a Structure–Activity Relationship Study—The Case of Cinnamic Acid Derivatives

Using a nitrification inhibitor to decrease nitrification rates in soil represents a promising strategy to improve nitrogen fertilizer use efficiency. Nonetheless, rapid screening of nitrification inhibitors remains challenging. In this study, we propose a strategy to screen potential nitrification inhibitors through a structure–activity relationship (SAR) study based on a rapid determination of nitrification inhibition. To demonstrate this, the nitrification inhibition potentials of cinnamic acid derivatives against Nitrosomonas europaea growth were evaluated in a liquid culture. The SAR study showed that hydroxyl and fluoride groups were the favorable substituents on the benzene ring, and the ester group and double bond in the side chain were essential for maintaining high inhibition efficacy. Three compounds with notable inhibitory efficacy (EC50 = 8–25 μM) were further assessed in agricultural soil, and they displayed a noteworthy reduction in nitrification rate and bacterial amoA gene numbers. Based on the results, we identified methyl cinnamate, methyl 4-hydroxycinnamate, and methyl 4-fluorocinnamate as promising candidates for nitrification inhibition.