Grid-connected Current Research Articles

Waveform Optimization Control of an Active Neutral Point Clamped Three-Level Power Converter System

Currently, the escalating integration of renewable energy sources is causing a steady weakening of grid strength. When grid strength is weak, interactions between inverters or those between inverters and grid line impedance can provoke widespread oscillations in the power system. Additionally, the diverse DC voltage application characteristics of power converter systems (PCS) may lead to over-modulation, generating narrow pulse issues that further impact control of the midpoint potential balance. Existing dead-time elimination methods are highly susceptible to current polarity judgments, rendering them ineffective in practical use. PCS, due to inherent dead-time effects, midpoint potential imbalances in three-level topologies, and narrow pulses, can elevate low-order harmonic content in the output voltage, ultimately distorting grid-connected currents. This is particularly susceptible to causing resonance in weak grids. To enhance the output voltage waveform of PCS, this article introduces a comprehensive compensation control strategy that combines dead-time elimination, midpoint potential balance, and narrow pulse suppression, all based on an active neutral point clamped (ANPC) three-level topology. This strategy gives precedence to dead-time elimination and calculates the upper and lower limits of the zero-sequence available for midpoint potential balance while fully compensating for narrow pulses. By prioritizing dead-time elimination, followed by narrow pulse suppression and finally midpoint potential balance, this method decouples the coupling between these three factors. The effectiveness of the proposed method is validated through semi-physical simulations.

LADRC-based grid-connected control strategy for single-phase LCL-type inverters.

To ensure that grid-connected currents are of high quality, it is crucial to optimize the dynamic performance of grid-connected inverters and their control. This study suggests using a combination of reduced-order linear active disturbance rejection control (LADRC) and a Proportional-Integral (PI) controller. By applying this control strategy to a single-phase photovoltaic grid-connected system, the system's ability to suppress grid harmonics is significantly improved. The validity and effectiveness of this control approach have been confirmed through simulations and experiments. The results show that the LADRC-based control system is robust and capable of rejecting disturbances, resulting in a significant reduction in the Total Harmonic Distortion (THD) of grid-connected currents. Comparative analysis with traditional control methods demonstrates the superior performance of the proposed approach.

The Quasi-Resonant Structure and Control Strategy of a Photovoltaic Flyback Grid-Connected Microinverter

This study proposes a topology structure for a flyback grid-connected inverter with a compensation capacitor. The addition of the compensation capacitor structure increases the harmonic oscillation period and reduces the switching frequency. Additionally, a control strategy for the microinverter is proposed. By using an accurate peak current reference curve, the system ensures precise turn-off signals, thus reducing the harmonic content of the grid-connected current. Simultaneously, the multi-valley turn-on strategy is employed to address the issue of high switching frequency, minimising the impact of energy. The proposed topology structure and control methods are modelled, simulated, and tested to validate the feasibility of the microinverter topology structure and the effectiveness of the control strategy, achieving a maximum efficiency of 95.2% and controlling the total harmonic distortion (THD) below 2.39%. Compared to other microinverter products, it is more efficient and stable.

Current-Prediction-Controlled Quasi-Z-Source Cascaded Multilevel Photovoltaic Inverter

To address problems that traditional two-stage inverters suffer such as high cost, low efficiency, and complex control, this study adopts a quasi-Z-source cascaded multilevel inverter. Firstly, the quasi-Z-source inverter utilizes a unique impedance network to achieve single-stage boost and inversion without requiring a dead zone setting. Additionally, its cascaded multilevel structure enables independent control of each power unit structure without capacitor voltage sharing problems. Secondly, this study proposes a current-predictive control strategy to reduce current harmonics on the grid side. Moreover, the feedback model of current and system state is established, and the fast control of grid-connected current is realized with the deadbeat control weighted by the predicted current deviation. And a grid-side inductance parameter identification is added to improve control accuracy. Also, an improved multi-carrier phase-shifted sinusoidal PWM method is adopted to address the issue of switching frequency doubling, which is caused by the shoot-through zero vector in quasi-Z-source inverters. Finally, the problems of switching frequency doubling and high harmonics on the grid side are solved by the improved deadbeat control strategy with an improved MPSPWM method. And a seven-level simulation model is built in MATLAB (2022b) to verify the correctness and superiority of the above theory.

Static model of DFIG wind farms considering control strategies

The static equivalent models of DFIG grid-connected currents vary under different control strategies. Traditional static equivalent algorithms fail to consider these differences, posing risks in static security analysis. In this study, based on the internal structure of DFIG, grid-connected current models for DFIG under different control strategies are established. The appropriate model is selected during the current calculation process based on the coupling relationship between active power (P) and reactive power (Q) of DFIG. Subsequently, generator nodes to be retained are selected according to the reactive power sensitivity of external network generators based on the internal network, and the node admittance matrix is modified to perform static equivalence. Results show that the proposed model in this study has higher accuracy compared to the traditional Ward equivalent model.

Model Predictive Control for Cascaded H-Bridge PV Inverter with Capacitor Voltage Balance

We designed an improved direct-current capacitor voltage balancing control model predictive control (MPC)for single-phase cascaded H-bridge multilevel photovoltaic (PV) inverters. Compared with conventional voltage balancing control methods, the method proposed could make the PV strings of each submodule operate at their maximum power point by independent capacitor voltage control. Besides, the predicted and reference value of the grid-connected current was obtained according to the maximum power output of the maximum power point tracking. A cost function was constructed to achieve the high-precision grid-connected control of the CHB inverter. Finally, the effectiveness of the proposed control method was verified through a semi-physical simulation platform with three submodules.

Impedance remodeling control strategy of grid-connected inverter with inertia-damping phase-locked loop under extremely weak grid

The operation of the grid-connected inverter (GCI) in weak grid conditions presents a risk of instability due to the presence of high grid impedance and the negative impedance effect of the phase-locked loop (PLL). In response to this issue, this paper introduces an impedance remodeling control strategy for the GCI utilizing the inertia-damping phase-locked loop (ID-PLL). Firstly, the proposed ID-PLL exhibits certain inertia and damping properties in comparison to the traditional PLL (T-PLL), resulting in an enhanced phase margin of the GCI system's equivalent output impedance. Consequently, the adaptation range of the grid impedance increases from 12mH (SCR = 3.00) to 24mH (SCR = 1.37). Next, from the perspective of impedance analysis, this study remodels the PLL impedance and inverter control loop impedance, further improving the amplitude and phase margin of the system's output impedance. As a result, the adaptation range of the grid impedance extends to 33mH (SCR = 1.00), and the transition of grid-connected currents becomes smooth and free of overshoot. Finally, the effectiveness of the proposed control strategy is validated through theoretical analysis and experimental verification.

Simulation system of intelligent photovoltaic grid-connected inverter considering fuzzy PI control

The grid connected inverter is the core component of the photovoltaic grid connected power generation system, which mainly converts the direct current of the photovoltaic matrix into alternating current that meets the grid connected requirements, playing a key role in the efficient and stable operation of the photovoltaic grid connected power generation system.This paper uses fuzzy PI control model which to improve the performance of intelligent photovoltaic grid-connected inverter to simulate the intelligent photovoltaic inverter system, using mathematical analysis and reasoning methods for model analysis,adopts two-stage three-phase LCL grid-connected inverter, establishes mathematical models in two-phase synchronous rotating and two-phase static coordinate systems, and adopts an active damping strategy based on grid-connected current. Based on existing research and empirical analysis,aiming at the disadvantage of poor dynamic response of repetitive control, an improved repetitive control strategy is adopted, and the controller is analyzed from two aspects of stability and dynamic performance, and the simulation model of photovoltaic grid-connected power generation system is built. Use experimental analysis method to verify the effectiveness of the model in this article,The experimental results show that the simulation system of intelligent photovoltaic grid-connected inverter considering fuzzy PI control proposed in this paper has certain effects.

A Hybrid Active Damping Strategy for Improving the Adaptability of LCL Converter in Weak Grid

In a weak grid, the line impedance variation will cause the resonant frequency of the LCL filter to shift towards lower frequencies, thus reducing the quality of the grid-connected current and affecting the power grid stability. To solve this problem, a hybrid active damping strategy with feedforward compensation is proposed for the neutral point clamped (NPC) LCL grid-connected inverter system. In order to reshape the output conductance of the grid-connected system, suppress the resonance spikes of the LCL filter and improve the adaptability of the grid-connected system to the weak grid. A first-order low-pass filter is designed in the grid-connected current loop, and an active damping control of grid-connected current based on a first-order high-pass filter is also proposed. Compared with the conventional capacitive current active damping, no additional sensors are required, and the use of a differential is avoided, which reduces the high-frequency noise. The use of passive resistors is reduced, which reduces the power loss of the grid-connected system. In addition, a point of common coupling (PCC) voltage feedforward strategy based on a low-pass filter is designed to suppress the background higher harmonics at PCC and improve the quality of grid-connected current. In this work, the robustness of the system is analyzed when the parameters of the LCL filter change. Finally, the virtual space vector modulation strategy is used to balance the neutral voltage of the DC bus. Simulation and experimental results show that the control strategy can effectively improve the adaptability of the system to the weak power grid, improve the quality of grid-connected current, and demonstrate strong stability. The THD can be decreased by 0.2% at least, and the improvements are more significant with larger line impedance; the THD is only 2.33% even at 10 mH line impedance.

A Fault-Tolerant Control Strategy for Three-Level Grid-Connected NPC Inverters after Single-Arm Failure with Optimized SVPWM

Three-level NPC inverters have been widely used in grid-connected systems due to their superior performance compared with two-level inverters, but more switches lead to high fault probability. Meanwhile, the neutral point potential (NPP) fluctuation of the DC link is an inherent problem of three-level NPC inverters. To keep the three-level NPC inverter running stably after single-arm failure, a fault-tolerant control strategy based on an optimised space vector pulse width modulation (SVPWM) is proposed in this paper. Firstly, the common-mode voltage (CMV) of the postfault three-level NPC inverter is analysed and then the preliminary synthesis principles of the reference voltage vector are determined. Then, in order to ensure the NPP balance and the quality of the grid-connected currents, the reference voltage vector synthesis rules are optimised, a low-pass filter (LPF) and a hysteresis comparator are designed, respectively, to ensure the quality of grid-connected currents and effectively decrease the DC link NPP deviation. Finally, the simulation results show that the proposed fault-tolerant control strategy can realize the stable and reliable operation of the grid-connected three-level NPC inverter after single-arm failure, and the CMV can be reduced significantly, the quality of grid-connected currents is also improved. The proposed fault-tolerant strategy also shows good performance when the grid-connected currents change.

Research on the Control Method of the PV Grid-Connected Inverter under an Asymmetrical Power Grid Fault

The negative-sequence current component and harmonic components generated when an asymmetrical fault occurs in the power grid seriously affect the normal operation of the photovoltaic (PV) grid-connected inverter. In order to suppress the negative-sequence current component and the harmonic component of the grid-connected current, and to meet the normal grid-connected operation requirements of the PV grid-connected inverter when asymmetrical faults occur in the grid, this paper proposes the proportional integral double-resonant (PI-DR) current controller, which consists of the PI controller and double-resonant controllers. The PI-DR current controller can directly control the negative-sequence current component and the grid-connected current harmonic component in the output current in the forward synchronous rotating coordinate system, without decomposing the positive and negative sequence currents. The PI-DR current controller ensures that the PV grid-connected inverter can realize normal grid-connected operation and improves the quality of the power when an asymmetrical fault occurs in the power grid. MATLAB/Simulink experiments show that the PI-DR current controller can improve the dynamic characteristics of the PV grid-connected inverter and improve the operating capability of the system when an asymmetrical fault occurs in the power grid.

Smart Nonlinear Energy Feedback Power Electronic Load to Simulate Power Quality Problems

This paper proposes a design approach for an energy feedback power electronic load (PEL) based on back-to-back voltage source PWM converters. It can simulate not only constant linear loads but also a class of nonlinear loads to simulate power quality problems. The rectifier side and the inverter side are decoupled in control by using a DC capacitor. The rectifier side is responsible for tracking designed current commands to achieve the designed load characteristics, and based on the characteristics of the current commands, a multi-resonant controller plus state feedback controller was designed by using the internal model principle. The inverter side employs an LCL filter with active damping to control the phase of the grid-connected current, enabling energy to feed back to the grid. A simulation model of this PEL is established in Simulink software, and the simulation results verify the effectiveness of the proposed control strategy.

Dynamic Performance Improvement of Continuous Control Set Model Predictive Control for High-Frequency Link Matrix Converter

In this paper, a comprehensive control strategy of a high frequency link matrix converter (HFLMC) based on the interaction technology between electric vehicle and power grid is proposed to improve the dynamic performance of the system. The continuous control set model predictive control (CCS-MPC) is applied to the current loop to solve the problems of difficult selection of PI control parameters and slow dynamic response speed. In order to ensure that the grid-connected current can achieve better command tracking, a deviation suppression term is introduced into the cost function of CCS-MPC, and the online auto tuning method of weight factors of fast-tracking term and deviation suppression term is designed. On this basis, the PWM signals are generated by the coordinated modulation strategy of the HFLMC to obtain a constant switching frequency, which makes the harmonic of the grid connected current easier to be filtered out. Experimental results show the correctness and feasibility of the proposed control strategy.

Research on improved Harmonic current detection method based on SOGI-PLL instantaneous reactive Power

In view of the traditional instantaneous reactive power detection has low anti-harmonic interference ability, poor real-time performance, and insufficient accuracy when the power grid frequency fluctuates, this paper improved the detection link. The working principle of single-phase harmonic detection is analyzed, and the improved second-order generalized integrator is added to make the phase-locked loop detect the voltage phase accurately and efficiently. Based on the comparison and compensation simulation results of the active compensation device, the quality of grid-connected current of the inverter is improved effectively, and the precision of phase locking is increased.

An Adaptive Virtual Impedance Method for Grid-Connected Current Quality Improvement of a Single-Phase Virtual Synchronous Generator under Distorted Grid Voltage.

The proportion of distributed generation systems in power grids is increasing, leading to the gradual emergence of weak grid characteristics. Moreover, using voltage-sourced grid-connected inverters can enhance the stability of a weak grid. However, due to the presence of background harmonics in weak grids, the grid voltage can cause significant distortions in the grid-connected current, which adversely affects the quality of the grid-connected current. This paper begins by briefly introducing the principle of the virtual synchronous generator (VSG). Then, the output current of the voltage source inverter is analyzed to elucidate the mechanism of harmonic current generation. Considering the distortion in the grid-connected current of the voltage source grid-connected inverter caused by background harmonics in the grid voltage, a harmonic current suppression strategy based on an adaptive virtual harmonic resistor is proposed. The proposed strategy employs a signal separation module based on multiple second-order generalized integrators connected through a cross-feedback network. This module effectively separates the fundamental and harmonic currents from the grid-connected current, extracts the amplitudes of the fundamental and harmonic currents through coordinate transformation, and adaptively adjusts the virtual harmonic resistance magnitude through the negative feedback control of the harmonic content (the ratio of the harmonic current amplitude to the fundamental current amplitude). These measures are used to enhance the quality of the grid-connected current. Additionally, the stability of the system is analyzed using the root locus of the open-loop transfer function. Finally, the effectiveness of the proposed method is validated through a combination of MATLAB/Simulink simulations and experimental results.

A Matching Scheduling Control Strategy Based on Modulation Wave Reconstruction for the Single-Phase Photovoltaic Cascaded Multilevel Inverter

The single-phase cascaded multilevel inverter (CMI) becomes an attractive solution for grid-connected photovoltaic (PV) power generation owing to its several advantages, such as the scalable modularity, the ability to reach the component level maximum power point tracking (MPPT), and the multilevel output voltage. However, the PV power of each H-bridge (HB) is uneven due to unequal illumination and partial shading of the PV panels, which may lead to overmodulation and further deteriorate the power quality of the grid-connected current. Existing methods to address this issue have not considered the effects on various operating conditions, and their application scope is limited. Therefore, this paper proposes a matching scheduling control strategy based on modulation wave reconstruction (MSMR). The relatively optimal modulation waveform of each HB is reconstructed scheduledly to match its PV power by detecting the operating conditions. Meanwhile, the PV power of each HB is adjusted to improve the ability to cope with the power unevenness. Finally, the proposed strategy is validated on a down-scaled experimental test bench.

Harmonic Suppression Strategy of LCL Grid-Connected PV Inverter Based on Adaptive QPR_PC Control

To reduce the influence of voltage harmonics on the grid current, a control strategy based on adaptive quasi-proportional phase compensated resonance (QPR_PC) is proposed. Firstly, the LCL grid-connected photovoltaic inverter system model is established, and the stability performance of the three-level inverter system under double closed-loop control is analyzed using the output impedance model of the inverter. Then, a QPR regulator for the zero steady-state error tracking of AC signals is studied. To solve the problem that the system has poor robustness against frequency changes when the traditional QPR regulator is used in the static coordinate system, this paper improves the traditional QPR regulator to optimize the response characteristics of the closed-loop system. Based on the QPR regulator, a phase margin compensation structure is introduced to form QPR_PC control. Then adaptive frequency design is added to ensure good control even when the power grid frequency drifts, which is the control strategy proposed in this paper. Verification shows that the proposed method improves the phase margin of output impedance at a specific frequency, restrains the interference of the 3rd, 5th, and 7th harmonics of grid voltage, and improves the dynamic performance of the system and the quality of grid-connected current. Finally, the simulation results show that the total harmonic distortion rate of grid-connected current is reduced by 1.03% after adopting this strategy, which verifies the effectiveness and correctness of the proposed method.

Research on Fuzzy Active Disturbance Rejection Control of LCL Grid-Connected Inverter Based on Passivity-Based Control in Weak Grid

In response to the problems of impedance variation and rich background harmonics in the weak grid environment of traditional LCL grid-connected inverters, which cause distortion of the grid-connected current and reduce the stability of the entire grid-connected system, this paper proposes a passive fuzzy-active disturbance rejection control strategy. Firstly, passivity-based control (PBC) is introduced into the grid-connected inverter system to ensure the global stability of the entire system. Secondly, in order to solve the problem of difficult selection of inverter-side current, active disturbance rejection control (ADRC) is used to directly track the grid-connected current, avoiding the tracking error of AC signal and suppressing the interference of background harmonics of grid voltage. The combination of fuzzy control and ADRC simplifies the system parameter tuning process, and the FUZZY-ADRC grid-connected current outer loop and PBC inductance current inner loop are combined to form a multi-loop control system. Finally, simulation comparison verifies that the proposed control strategy can effectively suppress the harmonics of grid-connected current, improve the quality of grid-connected current, and enhance the stability of the entire grid-connected system in a weak grid environment.

Parameter Design of Half-Bridge Converter Series Y-Connection Microgrid Grid-Connected Filter Based on Improved PSO-LSSVM

The half-bridge converter series Y-connection microgrid (HCSY-MG) is a new type of series microgrid. In order to reduce the harmonic content in HCSY-MG grid-connected current and at the same time simplify the parameter design process of the LCL filter, this study proposed an LCL filter parameter design method based on an improved particle swarm optimization-least squares support vector machine (PSO-LSSVM) by analyzing the harmonic characteristics of the HCSY-MG grid-connected current. In addition, to enhance the convergence speed of PSO-LSSVM, the inertia factor during its parameters’ update is made to adjust adaptively according to the direction of two consecutive parameter changes to constitute an improved PSO-LSSVM. Through simulation and comparative analysis, it is demonstrated that the improved PSO-LSSVM can enhance the convergence speed; the proposed filter parameter design method can effectively reduce the harmonic content in the HCSY-MG grid-connected current and is simpler and more comprehensive than the existing design method.

Grid Impedance Detection Based On Complex Coefficient Filter and Full-order Capacitor Current Observer for Three-phase Grid-connected Inverters

This article proposes a new grid impedance detection method incorporating the complex coefficient filter (CCF) with full-order capacitor current observer for a T-type three-level grid-connected inverter controlled by the inverter output current feedback. Compared with conventional CCF impedance detection algorithms, the proposed method reduces the number of current sensors and detects the grid impedance accurately. First, based on the sampled inverter output current and grid-connected voltage signals, the grid-connected current is estimated. Then, the CCF method is used to extract harmonics from the grid-connected current and voltage signals to calculate the grid impedance. Finally, the correctness of the full-order capacitor current observer is verified by simulation and the feasibility and effectiveness of the proposed algorithm are verified experimentally based on a laboratory prototype.