Great Potential For Widespread Application Research Articles

An adaptive online monitoring system using NFSOGI-PLL for three-phase voltage unbalance in grids

The extensive utilization of unbalanced and nonlinear loads has significantly impacted power quality in modern grids. Among various metrics, the three-phase voltage unbalance factor (TPVUF) stands out as a crucial indicator. To mitigate the challenges posed by harmonics and DC components that interfere with accurate TPVUF measurements, this paper introduces the Notch Filter-based Second-Order Generalized Integrator Phase-Locked Loop (NFSOGI-PLL) for the first time and designs an adaptive online monitoring system for TPVUF based on NFSOGI-PLL. To validate its performance, the hardware design and rapid software development of the NFSOGI-PLL-based TPVUF online monitoring system are thoroughly implemented, and the system is tested under various conditions. The results indicate that the proposed system not only provides real-time performance and high accuracy, complying with the rigorous standards set by GB/T 15543-2008 and IEC 61000-4-27, but also demonstrates remarkable stability under diverse influences. These findings underscore the exceptional filtering and tracking abilities of the NFSOGI-PLL in power systems, as well as the accuracy and anti-interference capabilities of the NFSOGI-based TPVUF online monitoring system, which holds great potential for widespread application in power system control and research.

High stability enhanced ultrasonic microfluidic structure with flexible tip coupled bubbles

Ultrasonic microfluidic technology is a technique that couples high-frequency ultrasonic excitation to microfluidic chips. To improve the issues of poor disturbance effects with flexible tip structures and the susceptibility of bubbles to thermal deformation, we propose an enhanced ultrasonic microchannel structure that couples flexible tips with bubbles aiming to improve the disturbance effects and the stability duration. Firstly, we used finite element analysis to simulate the flow field distribution characteristics of the flexible tip, the bubble, and the coupling structure and obtained the steady-state distribution characteristics of the velocity field. Next, we fabricated ultrasonic microfluidic chips based on these three structures, employing 2.8 μm polystyrene microspheres as tracers to analyze the disturbance characteristics of the flow field. Additionally, we analyzed the bubble size and growth rate within the adhering bubbles and coupling structures. Finally, we verified the applicability of the coupling structure for biological samples using human red blood cells (RBCs). Experimental results indicated that, compared to the flexible tip and adhering bubble structures, the flow field disturbance range of the coupling structure increased by 439.53% and 133.48%, respectively; the bubble growth rate reduced from 14.4% to 3.3%. The enhanced ultrasonic microfluidic structure proposed in this study shows great potential for widespread applications in micro-scale flow field disturbance and particle manipulation.

Design and testing of a low-cost mobile platform for contactless building surveying

After the completion of building construction, evaluating the accuracy of the distance between the lower edge of electrical switches and the one-meter line of the building is a crucial metric for assessing construction quality. Currently, the traditional measurement method basically uses manual measurement and is inefficient. To overcome this problem, we present a low-cost, non-contact mobile platform for building measurement, based on a 2D laser rangefinder and RGB camera. The system mainly consists of six key components: a mobile chassis, dual-axis gimbal, laser rangefinder, RGB camera, industrial control computer, and an automatic one-meter line calibration device, which can achieve high-precision distance measurement. Firstly, a sensorless control method for brushless DC motors (BLDCM) based on the Extended Kalman Filter (EKF) algorithm is proposed, which effectively improves the accuracy and robustness of rotor position estimation. Secondly, an automatic calibration device is developed to ensure the laser line consistently remains at a height of one meter from the ground. Finally, by combining image processing technology and 2D laser range data, the distance between the lower edge of the electrical switch and the building’s one-meter line is precisely measured using a triangulation algorithm. Experimental results show that the system’s measurements, compared to manual measurements, have a relative error percentage of 0.57%, while the automatic calibration device has a maximum error of only 0.2 centimeter. Therefore, the system shows great potential for widespread application in the field of building measurement.

Lentinan-based pH-responsive nanoparticles achieve the combination therapy of tumors

Cancer poses a significant threat to human health, and there is an urgent need for more effective treatments. Combining chemotherapy and immunotherapy is an effective strategy to enhance curative outcomes and holds great potential for widespread application. The natural phytochemical genistein (GEN) exhibits cytotoxicity against tumors and is a potential chemotherapeutic agent. Lentinan (LTN) is a natural polysaccharide with immune-enhancing properties that has been utilized in tumor treatment. This study constructed a pH-responsive nanoparticle GEN@LTN-BDBA with chemotherapy and immunotherapy functions using GEN and LTN. After characterizing the nanoparticles, the molecular mechanism of GEN@LTN-BDBA formation was explored using in silico simulation. GEN@LTN-BDBA can significantly inhibit the proliferation of A549 and HepG2 cells in vitro. The in vivo experiment results demonstrated that treatment with GEN@LTN-BDBA can significantly reduce tumor cell mass and prevent metastasis. In this nanoparticle, GEN induced oxidative stress and apoptosis of tumor cells. Meanwhile, the released LTN initiated an anti-tumor immune response by promoting dendritic cell (DC) maturation and upregulating the expression of costimulatory molecules and major histocompatibility complex. The construction method of GEN@LTN-BDBA can be extended to the preparation of other polysaccharides and hydrophobic chemotherapy molecules, offering a novel strategy to enhance the efficacy of monotherapy.

Chitosan-coated iron(III) oxide nanoparticles and tungsten disulfide quantum dots-immobilized Fiber-based WaveFlex Biosensor for Staphylococcus Aureus bacterial detection in real food samples

The research proposes and investigates an extraordinarily sensitive, label-free WaveFlex biosensor utilizing optical fiber technology for the detection of Staphylococcus aureus (S. aureus), a common foodborne bacterium. The WaveFlex biosensor (plasmon Wave based Flexible optical fiber Biosensor) is based on a novel flexible tapered single-mode fiber structure, utilizing gold nanoparticles (AuNPs) to trigger the phenomenon of localized surface plasmon resonance (LSPR). Additionally, the sensitivity is further enhanced using chitosan-coated iron(III) oxide nanoparticles (Fe3O4–CS NPs) and tungsten disulfide quantum dots (WS2-QDs). The optical fiber surface is functionalized with antibodies to achieve specific detection of S. aureus. For S. aureus concentrations at 1 × 108 CFU/mL (colony-forming units per milliliter), the sensor's maximum sensitivity of 2.74 nm/lg (CFU/mL), and a detection limit (LOD) of 6.67 CFU/mL. This ultra-sensitive biosensor holds great potential for widespread applications in various fields, including disease detection, medical diagnostics, and food safety inspection.

An efficient and generalisable approach for mapping paddy rice fields based on their unique spectra during the transplanting period leveraging the CIE colour space

As one of the most important staple foods globally, rice sustains nearly half of the world's population. Accurate and timely paddy rice mapping is, thus, essential for rice-related policy-making to ensure food security in the context of anthropogenic, environmental and climate changes. However, paddy rice mapping remains a challenging task since it usually has similar spectral characteristics to other land covers. In this research, for the first time, an entirely new approach, called RiceTColour, was proposed for mapping rice fields within the Commission Internationale de l'Eclairage (CIE) colour space based on their unique spectra during the rice transplanting period as observed in remotely sensed imagery. We demonstrate that transplanted rice fields, representing a mixture of soil, water and rice seedlings, consistently exhibit relatively low spectral values in both SWIR and NIR bands across various geographical locations, leading to their unique dark green colours in the false-colour image composed of SWIR, NIR and Red bands. Based upon this, we transformed these three spectral bands into the CIE colour space where paddy rice was found to be readily and completely separated from the other land covers. Straightforward, but specific classification criteria were established within the CIE colour space to differentiate paddy rice from the other land covers. The proposed RiceTColour, thus, represents a new approach for paddy rice identification, that is mapping paddy rice using the CIE colour space based upon the previous underexplored remotely sensed spectra of paddy fields during the transplanting season. The effectiveness of the proposed method was investigated over five rice-planting regions distributed across different geographical regions, characterised by different climates, rice cropping intensities, irrigation schemes and cultural practices. Specifically, the mapping criteria established in a training site (S1) were directly generalised to the other four sites (S2 to S5) for paddy rice mapping. Experimental results demonstrated that the RiceTColour method consistently achieved the most accurate and balanced classifications across all five sites compared with four benchmark comparators: a SAR-based method, an index-based method and two supervised classifier-based methods. In particular, the RiceTColour method performed relatively stable, producing an overall accuracy exceeding 95% in the training site (S1) as well as the four generalised sites (S2 to S5), which is an encouraging result. Such efficient yet stable rice mapping results across various rice-planting regions suggest a very strong generalisation capability of the proposed RiceTColour method. In consideration of the relatively large planting area of paddy rice fields globally, the proposed parameter-free, efficient, and generalisable RiceTColour method, thus, holds great potential for widespread application in various rice-planting areas worldwide.

Determination of ligand selectivity to G-tetrad through an AMCA fluorescence quenching approach

The selective binding of ligand molecules towards the 5′ and 3′ ends of G-quadruplex (G4) may differentially affect the physiological function of G4s. However, there is still a lack of sensitive and low-cost approaches to accurately measure the binding preference of ligands on G4s, although multiple ways have been developed to evaluate the interaction between ligands and G4s. Here, we propose a new protocol named G4-AFQ to test the selectivity of ligands towards the two terminal G-tetrads of G4s. In this protocol, the fluorophore AMCA is respectively modified at the 5′ or 3′ end of G4, and which end of AMCA fluorescence is quenched means that the ligand binds to the G-tetrad at that end. Through G4-AFQ, the affinity constant of ligands towards the binding site can also be obtained. Compared with the commonly used nuclear magnetic resonance (NMR) method, G4-AFQ is more convenient, sensitive, cost-effective, and suitable for the measurement of the vast majority of G4 ligands, with a great potential for widespread application.

Terahertz super-resolution imaging with large depth of field enabled by the terajet of bilayer dielectric spheres

Terahertz imaging has found extensive applications in non-destructive testing, security inspection, and other various fields. Intensive research on terahertz imaging systems has been executed to pursue high performance on imaging resolution and depth of field (DOF). However, the terahertz imaging systems with both high imaging resolution and large DOF have rarely been reported. In this paper, a mesoscopic-sized dielectric bilayer sphere-assisted super-resolution imaging method was proposed to simultaneously achieve enormously improved imaging resolution and extended DOF. Simulation analyses revealed that the ultrathin and long terajets were generated by the well-designed bilayer sphere. The THz super-resolution image for the samples can be captured by the point-by-point terajet scanning. The experimental results demonstrated that the best resolution reached up to 0.4λ, the DOF with super-resolution was up to 2λ, and the DOF with sub-wavelength resolution was up to 4λ. This method holds great potential for widespread application in terahertz imaging and detection, especially for curved or complex sample structures.

Improved remote sensing reference evapotranspiration estimation using simple satellite data and machine learning

Reference evapotranspiration (ET0) estimation is crucial for efficient irrigation planning, optimized water management and ecosystem modeling, yet it presents significant challenges, particularly when meteorological data availability is limited. This study utilized remote sensing data of land surface temperature (LST), day of year, and latitude, and employed a machine learning approach (i.e., random forest) to develop an improved remote sensing ET0 model. The model performed excellently in 567 meteorological stations in China with an R2 of 0.97, RMSE of 0.40, MBE of 0.00, and MAPE of 0.11 compared to the FAO-PM ET0; it also performed well globally, yielding an average R2 of 0.97 and RMSE of 0.43 across 120 sites in mid-latitude (20°-50°) regions. This model demonstrates simplicity, accuracy, robust and generalization, holding great potential for widespread application, especially in the large-scale, high-resolution estimation of ET0. This study will contribute to advancements in water resources management, agricultural planning, and climate change studies

Streamlined whole-genome genotyping through NGS-enhanced thermal asymmetric interlaced (TAIL)-PCR

Whole-genome genotyping (WGG) stands as a pivotal element in genomic-assisted plant breeding. Nevertheless, sequencing-based approaches for WGG continue to be costly, primarily owing to the high expenses associated with library preparation and the laborious protocol. During prior development of foreground and background integrated genotyping by sequencing (FBI-seq), we discovered that any sequence-specific primer (SP) inherently possesses the capability to amplify a massive array of stable and reproducible non-specific PCR products across the genome. Here, we further improved FBI-seq by replacing the adapter ligated by Tn5 transposase with an arbitrary degenerate (AD) primer. The protocol for the enhanced FBI-seq unexpectedly mirrors a simplified thermal asymmetric interlaced (TAIL)-PCR, a technique that is widely used for isolation of flanking sequences. However, the improved TAIL-PCR maximizes the primer-template mismatched annealing capabilities of both SP and AD primers. In addition, leveraging of next-generation sequencing enhances the ability of this technique to assay tens of thousands of genome-wide loci for any species. This cost-effective, user-friendly, and powerful WGG tool, which we have named TAIL-PCR by sequencing (TAIL-peq), holds great potential for widespread application in breeding programs, thereby facilitating genome-assisted crop improvement.

Different wettability surfaces composited by polydopamine-based SiO2/TiO2 coatings for efficient water collection and anti-corrosion application

Designing hybrid surfaces with superhydrophilic and superhydrophobic properties represents a promising approach for fog collection. Inspired by the adhesive properties of mussel proteins, a polydopamine (PDA) film was firmly attached to a brass surface through a combination of chemical etching and spontaneous dopamine polymerization. By harnessing the exceptional characteristics of PDA as a "double-sided adhesive," a hybrid surface with mixed wettability was created using a facile and cost-effective method involving SiO2 and TiO2 nanoparticles (NPs). The TiO2 NPs served as the hydrophilic sites for water capture, while the SiO2 NPs acted as the hydrophobic region to induce water droplet rolling. The resulting hybrid surface exhibited a significant improvement in water collection rate, measuring approximately 1.182 g/cm2/h, which was 1.84 times higher than that of the bare brass surface. This demonstrated a remarkable enhancement in fog collection capacity. Moreover, the hybrid surface demonstrated commendable corrosion resistance and remarkable durability, indicating its great potential for widespread application in practical scenarios.

Label-free and selective heparin detection by surface functionalized fiber Fabry-Perot interferometer biosensor

Heparin (Hep) is the most commonly used anticoagulant drug in clinical settings, and precise dosage control is crucial. To enable rapid and accurate quantification of Hep concentration in clinical practice, a label-free and selective fiber-optic Fabry-Perot interferometric (FPI) biosensor detection method based on graphene oxide (GO) was proposed. This method utilizes protamine (PRTM) sulfate as the modified layer and achieves Hep detection through layer-by-layer (LBL) assembly. In this study, we developed a label-free and selective fiber optic FPI biosensor for the detection of Hep using GO. The GO on the surface layer of the fiber optic FPI biosensor was treated with specific functionalization, it enables specific interaction with Hep. The binding of Hep to the functionalized surface induces a change in the luminal light signal, which can be monitored within the cavity for rapid and accurate detection of Hep. The results demonstrate that this biosensor exhibits good sensitivity, with a value of 10.82 nm/mM in the low-concentration control group, and an average limit of detection (LOD) calculated as 31μg/mL in the low-concentration group. This study presents a label-free, selective and efficient method for biomedical science testing that holds great potential for widespread application in clinical medicine.

A polynomial model with line-of-sight constraints for Lagrangian particle tracking under interface refraction

This paper introduces an improvement of the ‘shake-the-box (STB)’ (Schanz, Gesemann, and Schröder, Exp. Fluids 57.5, 2016) technique using the polynomial calibration model and the line-of-sight constraints (LOSC) to overcome the refractive interface issues in Lagrangian particle tracking (LPT) measurement. The method (named LOSC-LPT) draws inspiration from the two-plane polynomial camera calibration in tomographic particle image velocimetry (Worth, Nickels, Thesis, 2010) and the STB-based open-source Lagrangian particle tracking (OpenLPT) framework (Tan, Salibindla, Masuk, and Ni, Exp. Fluids 61.2, 2019). The LOSC-LPT introduces polynomial mapping functions into STB calibration in conditions involving gas–solid–liquid interfaces at container walls exhibiting large refractive index variations, which facilitates the realization of particle stereo matching, three-dimensional (3D) triangulation, iterative particle reconstruction, and further refinement of 3D particle position by shaking the LOS. Performance evaluation based on synthetic noise-free images with a particle image density of 0.05 particle per pixel in the presence of refractive interfaces demonstrates that LOSC-LPT can detect a higher number of particles and exhibits lower position uncertainty in the reconstructed particles, resulting in higher accuracy and robustness than that achieved with OpenLPT. In the application to an elliptical jet flow in an octagonal tank with refractive interfaces, the use of polynomial mapping results in smaller errors (mean calibration error <0.1 px) and thus more long trajectories identified by LOSC-LPT (13 000) compared with OpenLPT (4500) which uses the pinhole Tsai model (mean calibration error >1.0 px). Moreover, 3D flow-field reconstructions demonstrate that the LOSC-LPT framework can recover a more accurate 3D Eulerian flow field and capture more complete coherent structures in the flow, and thus holds great potential for widespread application in 3D experimental fluid measurements.

Large-FOV 3D localization microscopy by spatially variant point spread function generation.

Accurate characterization of the microscopic point spread function (PSF) is crucial for achieving high-performance localization microscopy (LM). Traditionally, LM assumes a spatially invariant PSF to simplify the modeling of the imaging system. However, for large fields of view (FOV) imaging, it becomes important to account for the spatially variant nature of the PSF. Here, we propose an accurate and fast principal components analysis-based field-dependent 3D PSF generator (PPG3D) and localizer for LM. Through simulations and experimental three-dimensional (3D) single-molecule localization microscopy (SMLM), we demonstrate the effectiveness of PPG3D, enabling super-resolution imaging of mitochondria and microtubules with high fidelity over a large FOV. A comparison of PPG3D with a shift-variant PSF generator for 3D LM reveals a threefold improvement in accuracy. Moreover, PPG3D is approximately 100 times faster than existing PSF generators, when used in image plane-based interpolation mode. Given its user-friendliness, we believe that PPG3D holds great potential for widespread application in SMLM and other imaging modalities.

Highly stable and antifungal properties on the oilseed rape of Cu3(MoO4)2(OH)2 nanoflakes prepared by simple aqueous precipitation

In the last few decades, nanoparticles have been a prominent topic in various fields, particularly in agriculture, due to their unique physicochemical properties. Herein, molybdenum copper lindgrenite Cu3(MoO4)2(OH)2 (CM) nanoflakes (NFs) are synthesized by a one-step reaction involving α-MoO3 and CuCO3⋅Cu(OH)2⋅xH2O solution at low temperature for large scale industrial production and developed as an effective antifungal agent for the oilseed rape. This synthetic method demonstrates great potential for industrial applications. Infrared spectroscopy and X-ray diffraction (XRD) results reveal that CM samples exhibit a pure monoclinic structure. TG and DSC results show the thermal stable properties. It can undergo a phase transition form copper molybdate (Cu3Mo2O9) at about 300 °C. Then Cu3Mo2O9 nanoparticles decompose into at CuO and MoO3 at 791 °C. The morphology of CM powder is mainly composed of uniformly distributed parallelogram-shaped nanoflakes with an average thickness of about 30 nm. Moreover, the binding energy of CM NFs is measured to be 2.8 eV. To assess the antifungal properties of these materials, both laboratory and outdoor experiments are conducted. In the pour plate test, the minimum inhibitory concentration (MIC) of CM NFs against Sclerotinia sclerotiorum (S. sclerotiorum) is determined to be 100 ppm, and the zone of inhibiting S. sclerotiorum is 14 mm. When the concentration is above 100 nm, the change rate of the hyphae circle slows down a little and begins to decrease until to 200 ppm. According to the aforementioned findings, the antifungal effects of a nano CM NFs solution are assessed at different concentrations (0 ppm (clear water), 40 ppm, and 80 ppm) on the growth of oilseed rape in an outdoor setting. The results indicate that the application of CM NFs led to significant inhibition of S. sclerotiorum. Specifically, when the nano CM solution was sprayed once at the initial flowering stage at a concentration of 80 ppm, S. sclerotiorum growth was inhibited by approximately 34%. Similarly, when the solution was sprayed once at the initial flowering stage and once at the rape pod stage, using a concentration of 40 ppm, a similar level of inhibition was achieved. These outcomes show that CM NFs possess the ability to bind with more metal ions due to their larger specific surface area. Additionally, their semiconductor physical properties enable the generation of reactive oxygen species (ROS). Therefore, CM NFs hold great potential for widespread application in antifungal products.

Quantification of three-dimensional added turbulence intensity for the horizontal-axis wind turbine considering the wake anisotropy

The accurate evaluation of wake turbulence intensity (TI) is of great significance for the layout optimization of wind farms and research on control strategies. However, the existing engineering wake models still have many shortcomings in evaluating the TI in the wake of horizontal-axis wind turbines (HAWTs), especially in the near wake region. In response to this, this article proposed an analytical model based on the double-Gaussian ellipse function that can describe the three-dimensional added TI distribution in the entire wake region. Firstly, the anisotropy of wake expansion is taken into account in both the horizontal and vertical directions, assuming that the added TI distribution downstream of the HAWT is a double-Gaussian elliptical shape. Secondly, taking into account the self-similarity characteristics of flow TI, the maximum added TI and its position in the entire wake region are evaluated. In addition, considering the influence of the ground effect, the vertical turbulence distribution was corrected. Finally, the proposed added turbulence model was validated and relative error analysis was conducted using large eddy simulation (LES) data, wind field measurement data, and wind tunnel experimental data. The results show that the model had good prediction accuracy in the entire wake region, and its prediction performance was significantly improved compared to traditional models, especially in the near wake region, with the lowest even relative error of 3.66%. This model has significant advantages such as low computational cost, wide applicability, and high accuracy. It can reduce energy losses in wind farms, improve wind energy utilization efficiency, and has great potential for widespread application in large-scale wind farms.

Solvent-free polyurethane coatings based on an in-situ curing strategy at room temperature with self-cleaning, anti-corrosion and anti-graffiti properties

Anti-smudge coatings have attracted extensive attention in recent years owing to their hydrophobic, self-cleaning, anti-graffiti properties and so on. However, most of the anti-smudge coatings are solvent-based and cured at high temperature or using special curing equipment, which negatively impacts the environment and limits their large-scale application in daily life. Herein, we report a solvent-free anti-smudge coating with potential for large-scale and green manufacturing. In detail, polydimethylsiloxane (PDMS) was used as the hydrophobic component, (3-aminopropyl)triethoxysilane (APTES) and 3-glycidoxypropyltrimethoxysilane (GPTMS) were used as the cross-linking agent, and a solvent-free polyurethane (SFPU) anti-smudge coating was in-situ constructed at room temperature for 24 h without any curing equipment. Due to the enrichment of PDMS chains on the surface and the dense cross-linked network of the coating, the as-prepared coating not only exhibited a high contact angle for water (99.3 ± 1.5°) and diiodomethane (69.5 ± 0.9°), but also excellent anti-smudge to contaminants, with both water and oily liquids were easy to slide off the surface of the coating without leaving any traces. Even after writing with an oil-based marker, the ink on the coated surface could be easily wiped off. Further study reveals that the coating surface maintained its original liquid repellency and stain resistance even after 10 d immersion in a 10 wt% NaCl solution, showing durable anti-corrosion properties. In addition, pigments did not affect the anti-graffiti performance of the coating, providing a multi-color scheme for practical application. This convenient, low-energy, environmentally friendly anti-smudge coating has great potential for widespread application in industry and daily life.

Electrostatic microfiltration (EM) enriches and recovers viable microorganisms at low-abundance in large-volume samples and enhances downstream detection.

Rapid and sensitive detection of pathogens in various samples is crucial for disease diagnosis, environmental surveillance, as well as food and water safety monitoring. However, the low abundance of pathogens (<10 CFU) in large volume (1 mL-1 L) samples containing vast backgrounds critically limits the sensitivity of even the most advanced techniques, such as digital PCR. Therefore, there is a critical need for sample preparation that can enrich low-abundance pathogens from complex and large-volume samples. This study develops an efficient electrostatic microfiltration (EM)-based sample preparation technique capable of processing ultra-large-volume (≥500 mL) samples at high throughput (≥10 mL min-1). This approach achieves a significant enrichment (>8000×) of extremely-low-abundance pathogens (down to level of 0.02 CFU mL-1, i.e., 10 CFU in 500 mL). Furthermore, EM-enabled sample preparation facilitates digital amplification techniques sensitively detecting broad pathogens, including bacteria, fungi, and viruses from various samples, in a rapid (≤3 h) sample-to-result workflow. Notably, the operational ease, portability, and compatibility/integrability with various downstream detection platforms highlight its great potential for widespread applications across diverse settings.

Kapok derived microtubular FeCo/CMT with high specific surface area for broadband microwave absorption

Since biomass-derived carbon materials possess the advantages of peculiar morphology and low density. They have received significant attention on microwave absorption materials. We synthesize a one-dimensional hollow FeCo/carbon microtubule (FeCo/CMT) derived from homogeneous kapok fiber using a feasible solvothermal method and calcination process. The graphitization degree and magnetic properties of FeCo/CMT could be controlled by manipulating the calcination temperature. The FeCo/CMT composite with the calcination temperature of 600 °C demonstrated exceptional microwave absorption performance, characterized by strong absorption (−50.6 dB), broadband absorption (12.4–18.0 GHz), thin thickness (2.5 mm), and low loading (10 wt%). The hollow structure, interfacial polarization, and the synergistic effect between FeCo and CMT collectively account for the microwave absorption mechanisms. Considering its outstanding comprehensive characteristics and performance, the biomass-derived hollow FeCo/CMT shows great potential for widespread application as a high-performance microwave absorption material.

Novel fabric-based 3D photothermal evaporator with advanced light-harvesting and thermal management design

Interfacial photothermal evaporation offers a promising and cost-effective method of obtaining freshwater. Traditional photothermal evaporators, when exposed to sunlight, typically have a heating region on their surface with temperature higher than room temperature. This can lead to thermal radiation loss and reduce evaporation efficiency. Therefore, this study presents an innovative design and fabrication of a fabric-based conical roll (FCR) evaporator, which enables low-temperature evaporation without a distinct heating region and facilitates the reversal of the thermal radiation path. In particular, the FCR-7.5-45 evaporator demonstrated remarkable performance even under 2.0 sun illumination, showcasing its advanced light-harvesting capability and excellent thermal management ability attributable to the conical spiral groove structure. The unique cold evaporation surface of the 3D evaporators, combined with this design, resulted in a high evaporation efficiency of 151.53 % and a rapid evaporation rate of 3.47 kg·m−2·h−1 under 1.0 sun illumination. Furthermore, the freshwater produced by the FCR evaporator met the drinking water standards set by international regulatory bodies. This indicates that the photothermal evaporator developed in this project holds great potential for widespread application in desalination and sewage treatment.