Interferometric Gravitational Wave Research Articles

Stochastic gravitational wave background from newly born massive magnetars: The role of a dense matter equation of state

Newly born massive magnetars are generally considered to be produced by binary neutron star (NS) mergers, which could give rise to short gamma-ray bursts (SGRBs). The strong magnetic fields and fast rotation of these magnetars make them promising sources for gravitational wave (GW) detection using ground based GW interferometers. Based on the observed masses of Galactic NS-NS binaries, by assuming different equations of state (EOSs) of dense matter, we investigate the stochastic gravitational wave background (SGWB) produced by an ensemble of newly born massive magnetars. The massive magnetar formation rate is estimated through: (i) the SGRB formation rate (hereafter entitled as MFR1); (ii) the NS-NS merger rate (hereafter entitled as MFR2). We find that for massive magnetars with masses $M_{\rm mg}=2.4743 M_\odot$, if EOS CDDM2 is assumed, the resultant SGWBs may be detected by the future Einstein Telescope (ET) even for MFR1 with minimal local formation rate, and for MFR2 with a local merger rate $\dot{\rho}_{\rm c}^{\rm o}(0)\lesssim 10$ ${\rm Mpc}^{-3}{\rm Myr}^{-1}$. However, if EOS BSk21 is assumed, the SGWB may be detectable by the ET for MFR1 with the maximal local formation rate. Moreover, the background spectra show cutoffs at about 350 Hz in the case of EOS BSk21, and at 124 Hz for CDDM2, respectively. We suggest that if the cutoff at $\sim100$ Hz in the background spectrum from massive magnetars could be detected, then the quark star EOS CDDM2 seems to be favorable. Moreover, the EOSs, which present relatively small TOV maximum masses, would be excluded.

Limiting the effects of earthquakes on gravitational-wave interferometers

Ground-based gravitational wave interferometers such as the Laser Interferometer Gravitational-wave Observatory (LIGO) are susceptible to ground shaking from high-magnitude teleseismic events, which can interrupt their operation in science mode and significantly reduce their duty cycle. It can take several hours for a detector to stabilize enough to return to its nominal state for scientific observations. The down time can be reduced if advance warning of impending shaking is received and the impact is suppressed in the isolation system with the goal of maintaining stable operation even at the expense of increased instrumental noise. Here, we describe an early warning system for modern gravitational-wave observatories. The system relies on near real-time earthquake alerts provided by the U.S. Geological Survey (USGS) and the National Oceanic and Atmospheric Administration (NOAA). Preliminary low latency hypocenter and magnitude information is generally available in 5 to 20 min of a significant earthquake depending on its magnitude and location. The alerts are used to estimate arrival times and ground velocities at the gravitational-wave detectors. In general, 90% of the predictions for ground-motion amplitude are within a factor of 5 of measured values. The error in both arrival time and ground-motion prediction introduced by using preliminary, rather than final, hypocenter and magnitude information is minimal. By using a machine learning algorithm, we develop a prediction model that calculates the probability that a given earthquake will prevent a detector from taking data. Our initial results indicate that by using detector control configuration changes, we could prevent interruption of operation from 40 to 100 earthquake events in a 6-month time-period.

Experimental demonstration of coupled optical springs

Optical rigidity will play an important role in improving the sensitivity of future generations of gravitational wave (GW) interferometers, which employ high laser power in order to reach and exceed the standard quantum limit. Several experiments have demonstrated the combined effect of two optical springs on a single system for very low-weight mirror masses or membranes. In this paper we investigate the complex interactions between multiple optical springs and the surrounding apparatus in a system of comparable dynamics to a large-scale GW detector. Using three 100 g mirrors to form a coupled cavity system capable of sustaining two or more optical springs, we demonstrate a number of different regimes of opto-mechanical rigidity and measurement techniques. Our measurements reveal couplings between each optical spring and the control loops that can affect both the achievable increase in sensitivity and the stability of the system. Hence this work establishes a better understanding of the realisation of these techniques and paves the way to their application in future GW observatories, such as upgrades to Advanced LIGO.

Graviton mass bounds from an analysis of bright star trajectories at the Galactic Center

In February 2016 the LIGO & VIRGO collaboration reported the discovery of gravitational waves in merging black holes, therefore, the team confirmed GR predictions about an existence of black holes and gravitational waves in the strong gravitational field limit. Moreover, in their papers the joint LIGO & VIRGO team presented an upper limit on graviton mass such as mg eV (Abbott et al. 2016). So, the authors concluded that their observational data do not show any violation of classical general relativity. We show that an analysis of bright star trajectories could constrain graviton mass with a comparable accuracy with accuracies reached with gravitational wave interferometers and the estimate is consistent with the one obtained by the LIGO & VIRGO collaboration. This analysis gives an opportunity to treat observations of bright stars near the Galactic Center as a useful tool to obtain constraints on the fundamental gravity law such as modifications of the Newton gravity law in a weak field approximation. In that way, based on a potential reconstruction at the Galactic Center we obtain bounds on a graviton mass.

Folding gravitational-wave interferometers

The sensitivity of kilometer-scale terrestrial gravitational wave interferometers is limited by mirror coating thermal noise. Alternative interferometer topologies can mitigate the impact of thermal noise on interferometer noise curves. In this work, we explore the impact of introducing a single folding mirror into the arm cavities of dual-recycled Fabry–Perot interferometers. While simple folding alone does not reduce the mirror coating thermal noise, it makes the folding mirror the critical mirror, opening up a variety of design and upgrade options. Improvements to the folding mirror thermal noise through crystalline coatings or cryogenic cooling can increase interferometer range by as much as a factor of two over the Advanced LIGO reference design.

Approximate universal relations among tidal parameters for neutron star binaries

One of largest uncertainties in nuclear physics is the relation between the pressure and density of supranuclear matter: the equation of state. Some of this uncertainty may be removed through future gravitational wave observations of neutron star binaries by extracting the tidal deformabilities (or Love numbers) of neutron stars, a novel way to probe nuclear physics in the high-density regime. Previous studies have shown that only a certain combination of the individual (quadrupolar) deformabilities of each body (the so-called chirp tidal deformability) can be measured with second-generation, gravitational wave interferometers, such as Adv. LIGO, due to correlations between the individual deformabilities. To overcome this, we search for approximately universal (i.e. approximately equation-of-state independent) relations between two combinations of the individual tidal deformabilities, such that once one of them has been measured, the other can be automatically obtained and the individual ones decoupled through these relations. We find an approximately universal relation between the symmetric and the anti-symmetric combination of the individual tidal deformabilities that is equation-of-state-insensitive to for binaries with masses less than . We show that these relations can be used to eliminate a combination of the tidal parameters from the list of model parameters, thus breaking degeneracies and improving the accuracy in parameter estimation. A simple (Fisher) study shows that the universal binary Love relations can improve the accuracy in the extraction of the symmetric combination of tidal parameters by as much as an order of magnitude, making the overall accuracy in the extraction of this parameter slightly better than that of the chirp tidal deformability. These new universal relations and the improved measurement accuracy on tidal parameters not only are important to astrophysics and nuclear physics, but also impact our ability to probe extreme gravity with gravitational waves and cosmology.

Subtraction of correlated noise in global networks of gravitational-wave interferometers

The recent discovery of merging black holes suggests that a stochastic gravitational-wave background is within reach of the advanced detector network operating at design sensitivity. However, correlated magnetic noise from Schumann resonances threatens to contaminate observation of a stochastic background. In this paper, we report on the first effort to eliminate intercontinental correlated noise from Schumann resonances using Wiener filtering. Using magnetometers as proxies for gravitational-wave detectors, we demonstrate as much as a factor of two reduction in the coherence between magnetometers on different continents. While much work remains to be done, our results constitute a proof-of-principle and motivate follow-up studies with a dedicated array of magnetometers.

Probing the electroweak phase transition with Higgs factories and gravitational waves

After the discovery of the Higgs boson, understanding the nature of electroweak symmetry breaking and the associated electroweak phase transition has become the most pressing question in particle physics. Answering this question is a priority for experimental studies. Data from the LHC and future lepton collider-based Higgs factories may uncover new physics coupled to the Higgs boson, which can induce the electroweak phase transition to become first order. Such a phase transition generates a stochastic background of gravitational waves, which could potentially be detected by a space-based gravitational wave interferometer. In this paper, we survey a few classes of models in which the electroweak phase transition is strongly first order. We identify the observables that would provide evidence of these models at the LHC and next-generation lepton colliders, and we assess whether the corresponding gravitational wave signal could be detected by eLISA. We find that most of the models with first order electroweak phase transition can be covered by the precise measurements of Higgs couplings at the proposed Higgs factories. We also map out the model space that can be probed with gravitational wave detection by eLISA.

The effect of time on optical coating mechanical loss and implications for LIGO-India

We report on the persistence of mechanical loss with time of ion beam sputtered dielectric coatings made from alternating layers of Ta2O5 and SiO2 deposited onto fused silica substrates. From this, we predict the coating thermal noise in gravitational wave interferometers, after the coated optics have been stored for years. We measured the modal mechanical quality factor, Q, of two coated fused silica samples in 2015. These samples also had their modal Q's measured in 2002. We conclude that storing the coated silica disks for 13 years does not change their mechanical loss and thus the storage of Advanced LIGO gravitational wave detector optics until their future installation in India will not degrade their achievable thermal noise.

Experimental study of diode pumped rubidium amplifier for single higher-order Laguerre-Gaussian modes.

In this paper, we have set up a diode laser pumped rubidium amplifier for higher-order Laguerre-Gauss (LG) modes. We experimentally realized amplification of higher-order LG modes including helical and sinusoidal LG03, LG13, LG23, and LG33 modes with their high purity held. This novel scheme of generating high-purity higher-order LG beams at high laser power is preferred to the second-generation gravitational wave interferometers. To the best of our knowledge, it is the first time this scheme is formulated.

Primordial gravitational waves for universality classes of pseudoscalar inflation

Current bounds from the polarization of the CMB predict the scale-invariant gravitational wave (GW) background of inflation to be out of reach for upcoming GW interferometers. This prospect dramatically changes if the inflaton is a pseudoscalar, in which case its generic coupling to any abelian gauge field provides a new source of GWs, directly related to the dynamics of inflation. This opens up new ways of probing the scalar potential responsible for cosmic inflation. Dividing inflation models into universality classes, we analyze the possible observational signatures. One of the most promising scenarios is Starobinsky inflation, which may lead to observational signatures both in direct GW detection as well as in upcoming CMB detectors. In this case, the complementarity between the CMB and direct GW detection, as well as the possibility of a multi-frequency analysis with upcoming ground and space based GW interferometers, may provide a first clue to the microphysics of inflation.

Chiral primordial gravitational waves from dilaton induced delayed chromonatural inflation

We study inflation driven by a dilaton and an axion, both of which are coupled to a SU(2) gauge field. We find that the inflation driven by the dilaton occurs in the early stage of inflation during which the gauge field grows due to the gauge-kinetic function. When the energy density of magnetic fields catches up with that of electric fields, chromonatural inflation takes over in the late stage of inflation, which we call delayed chromonatural inflation. Thus, the delayed chromonatural inflation driven by the axion and the gauge field is induced by the dilaton. The interesting outcome of the model is the generation of chiral primordial gravitational waves on small scales. Since the gauge field is inert in the early stage of inflation, it is viable in contrast to the conventional chromonatural inflation. We find the parameter region where chiral gravitational waves are generated in a frequency range higher than nHz, which are potentially detectable in future gravitational wave interferometers and pulsar-timing arrays such as DECi-hertz Interferometer Gravitational wave Observatory (DECIGO), evolved Laser Interferometer Space Antenna (eLISA), and Square Kilometer Array (SKA).

Constraining the range of Yukawa gravity interaction from S2star orbits II: bounds on graviton mass

Recently LIGO collaboration discovered gravitational waves [1] predicted 100 years ago by A. Einstein. Moreover, in the key paper reporting about the discovery, the joint LIGO & VIRGO team presented an upper limit on graviton mass such as mg < 1.2 × 10−22 eV [2] (see also more details in another LIGO paper [3] dedicated to a data analysis to obtain such a small constraint on a graviton mass). Since the graviton mass limit is so small the authors concluded that their observational data do not show violations of classical general relativity. We consider another opportunity to evaluate a graviton mass from phenomenological consequences of massive gravity and show that an analysis of bright star trajectories could bound graviton mass with a comparable accuracy with accuracies reached with gravitational wave interferometers and expected with forthcoming pulsar timing observations for gravitational wave detection. It gives an opportunity to treat observations of bright stars near the Galactic Center as a wonderful tool not only for an evaluation specific parameters of the black hole but also to obtain constraints on the fundamental gravity law such as a modifications of Newton gravity law in a weak field approximation. In particular, we obtain bounds on a graviton mass based on a potential reconstruction at the Galactic Center.

Tackling excess noise from bilinear and nonlinear couplings in gravitational-wave interferometers

We describe a tool we improved to detect excess noise in the gravitational wave (GW) channel arising from its bilinear or nonlinear coupling with fluctuations of various components of a GW interferometer and its environment. We also describe a higher-order statistics tool we developed to characterize these couplings, e.g., by unraveling the frequencies of the fluctuations contributing to such noise, and demonstrate its utility by applying it to understand nonlinear couplings in Advanced LIGO engineering data. Once such noise is detected, it is highly desirable to remove it or correct for it. Such action in the past has been shown to improve the sensitivity of the instrument in searches of astrophysical signals. If this is not possible, then steps must be taken to mitigate its influence, e.g., by characterizing its effect on astrophysical searches. We illustrate this through a study of the effect of transient sine-Gaussian noise artifacts on a compact binary coalescence template bank.

Studies on the high-energy follow-up of gravitational wave transient events

Second-generation gravitational wave interferometers, such as Advanced LIGO and Advanced Virgo, will soon reach sensitivities sufficient to first detect gravitational waves and open a new era in the multi-messenger investigations of the cosmos. The most violent and energetic astrophysical phenomena, including the mergers of compact objects or the core collapse of massive stars, are promising sources of gravitational waves, and are thought to be connected with transient phenomena such as Gamma Ray Bursts and supernovae. Combined observations of gravitational and electromagnetic signals from these events will thus provide a unique opportunity to unveil their progenitors and study the physics of compact objects. In particular, gamma-ray ground-based and space observatories such as Fermi or the Air Cherenkov Telescopes will be crucial to observe the high-energy electromagnetic counterparts of transient gravitational wave signals and provide a robust identification based on a precise sky localization. We will report on our studies of possible joint observation strategies carried on by gravitational interferometers and gamma-ray telescopes, with particular attention to the high-energy follow-up of Gamma Ray Bursts.

Methodology of the joint search for Gravitational Wave and Low Energy Neutrino signals from Core-Collapse Supernovae

Core-Collapse Supernovae (CCSNe) have a neutrino (v) signature confirmed by SN 1987A and are potential sources of Gravitational Waves (GWs). vs and GWs coming from these sources will reach the observer almost simultaneously and without significant interaction with interstellar matter. The expected GW signals are in the range of the upcoming advanced detectors for galactic neighborhood events. However, there are still significant uncertainties on the theoretical model of the emission. A joint search of coincident vs and GWs from these sources would bring valuable information from the inner core of the collapsing star and would enhance the detection of the so-called Silent Supernovae. Recently, a project for a joint search involving GW interferometers and v detectors has started. In this paper we discuss about the principal GW theoretical models of emission, and we present a methodological study of the joint search project between GW and v.

Coping with pressure

Radiation pressure noise from squeezed light constrains the precision of sensing devices such as improved gravitational wave interferometers.

Demonstration of an optical spring in the 100 g mirror regime

Optical rigidity will play an important role in future generations of gravitational wave (GW) interferometers which employ high laser power in order to reach and exceed the standard quantum limit. Several experiments have demonstrated the optical spring effect for very low weight mirror masses. In this paper we extend this to a mass and frequency regime more directly applicable to GW detectors. Using a end mirror mass we demonstrate an optical spring resonant at and a stiffness of 9.4 ×105 N m−1. The to mass regime may also be useful for the application as a readout mirror for optical bar or optical lever configurations.

Observationally constraining gravitational wave emission from short gamma-ray burst remnants

Observations of short gamma-ray bursts indicate ongoing energy injection following the prompt emission, with the most likely candidate being the birth of a rapidly rotating, highly magnetized neutron star. We utilize X-ray observations of the burst remnant to constrain properties of the nascent neutron star, including its magnetic field-induced ellipticity and the saturation amplitude of various oscillation modes. Moreover, we derive strict upper limits on the gravitational wave emission from these objects by looking only at the X-ray light curve, showing the burst remnants are unlikely to be detected in the near future using ground-based gravitational wave interferometers, such as Advanced LIGO.

Squeezing quadrature rotation in the acoustic band via optomechanics

We examine the use of optomechanically generated squeezing to obtain a sensitivity enhancement for interferometers in the gravitational-wave band. The intrinsic dispersion characteristics of optomechanical squeezing around the mechanical frequency are able to produce squeezing at different quadratures over the spectrum, a feature required by gravitational-wave interferometers to beat the standard quantum limit over an extended frequency range. Under realistic assumptions we show that the amount of available squeezing and the intrinsic quadrature rotation may provide, compared to similar amounts of fixed-quadrature squeezing, a detection advantage. A significant challenge for this scheme, however, is the amount of excess noise that is generated in the unsqueezed quadrature at frequencies near the mechanical resonance.