Grain Size Distribution Research Articles

Study of the rheological properties and nautical depth assessment of fine sediments in Iranian ports

Sediments containing more than 10% clay particles by mass can exhibit cohesive properties. Cohesive sediments are commonly found in coastal areas worldwide, including the southern shore of the Caspian Sea and the northern/northwestern beaches of the Persian Gulf. These cohesive sediments can form a layer of soft to extremely soft mud, known as fluid mud, covering the seabed. The study examined the properties of natural mud samples collected from different depths and locations within three Iranian ports: Anzali Port (Caspian Sea), and Khorramshahr and Bushehr Ports (Persian Gulf). The laboratory analyses included determining the sediment grain-size distribution, density, carbonate content, organic matter content, and rheological properties at different water content ratios. Disregarding the impact of variations in organic matter and carbonate contents in the samples, water content ratio was the main factor affecting the rheological properties of sediments.

Thermodynamics of Giant Molecular Clouds: The Effects of Dust Grain Size

The dust grain size distribution (GSD) likely varies significantly across star-forming environments in the Universe, but its impact on star formation remains unclear. This ambiguity arises because the GSD interacts nonlinearly with processes like heating, cooling, radiation, and chemistry, which have competing effects and varying environmental dependencies. Processes such as grain coagulation, expected to be efficient in dense star-forming regions, reduce the abundance of small grains and increase that of larger grains. Motivated by this, we investigate the effects of similar GSD variations on the thermochemistry and evolution of giant molecular clouds (GMCs) using magnetohydrodynamic simulations spanning a range of cloud masses and grain sizes, which explicitly incorporate the dynamics of dust grains within the full-physics framework of the STARFORGE project. We find that grain size variations significantly alter GMC thermochemistry: the leading-order effect is that larger grains, under fixed dust mass, GSD dynamic range, and dust-to-gas ratio, result in lower dust opacities. This reduced opacity permits interstellar radiation field and internal radiation photons to penetrate more deeply. This leads to rapid gas heating and inhibited star formation. Star formation efficiency is highly sensitive to grain size, with an order-of-magnitude reduction when grain size dynamic range increases from 10−3–0.1 μm to 0.1–10 μm. Additionally, warmer gas suppresses low-mass star formation, and decreased opacities result in a greater proportion of gas in diffuse ionized structures.

Effects of Zn2+/Si4+ co-doping on the cation distribution, crystal structure, and microwave dielectric characteristics of spinel-structured MgAl2O4 ceramics

Investigating the relationship between the structure and dielectric properties of cation-mixed spinel ceramics is crucial for overcoming the limitations of conventional microwave materials. In this study, MgAl2-x(Zn0.5Si0.5)xO4 (x = 0, 0.02, 0.04, 0.06, and 0.08) ceramics were prepared by a solid-state reaction method. The co-substitution for Al with Zn2+/Si4+ induces Al3+ cations for preferential occupation of the 8a site in the oxygen tetrahedra, forming a solid-solution ceramic at x ≤ 0.06. Enhanced ionic diffusion and compressive stress contribute to a dense microstructure (ρ > 95%) with uniform grain-size distribution after heating at 1650 °C for 4 h. Raman and 27Al NMR spectra reveal a relationship between cation distribution and covalency, consistent with the results of Rietveld refinement. The increases in cation disorder and degree of inversion are accompanied by an enhanced covalency of the Al–O bonds, which reduces intrinsic dielectric loss. In addition, the combination of Shannon ion polarizability and bond valence theory suggests that the increases in permittivity (εr) and the temperature coefficient of resonant frequency (τf) are related to the high polarizability of the dopant ions and the abnormal polarizability derived from the decreasing bond valence of the Al2–O site. The sample at x = 0.06 exhibits a low εr of 8.31, high Q × f of 194,159 GHz (at ∼11.35 GHz), and τf of -30.8 ppm/°C, indicating superior microwave application prospects as compared with traditional Mg-Al spinel ceramics.

A finite mixture distribution to model genetic architecture of image‐based oat grain morphology

AbstractThe multi‐floral oat (Avena sativa L.) inflorescence influences grain size and shape distributions, affecting the physical attributes of grain quality such as plumpness, size, and uniformity. While the grain size and shape distribution has been characterized as multi‐modal, very little is known about the genetic determinants of those distributions and their properties. The goal of this study was to model grain size and shape distribution using a finite mixture distribution approach and propose new distributional traits (i.e., emerging distributional traits) to characterize genotypes. We evaluated 47 oat genotypes in four highly replicated field experiments. Grains of three panicles per plot were individually threshed and scanned. Grain area, length, width, and roundness were obtained from each grain‐based image, while emerging distributional traits were evaluated using a finite mixture distribution approach. Finally, grain size distributions from hand‐threshed panicles (representing the full biological distribution) were compared with the grain size distributions of grains harvested with a combine harvester representing commercial harvest where small grains may be blown out. The heritability of all grain traits was high (0.89–0.94), and trait distributions differed among genotypes. Grain area and length show bi‐ and trimodal distributions, while grain width and roundness are uni‐ and bimodal. Although the full biological distribution of grains differed from the combine‐harvested grains, their genetic correlations were high, suggesting the combine‐harvested distributions can be used as a proxy for full biological distributions. This study proposes a straightforward methodological approach to model grain attributes that can aid in quality evaluations for genetic studies, breeding decisions, and industry characterization.

Microstructure evolution, elemental diffusion behavior, and bonding strength of TA1/AZ31B laminated composite fabricated by hot pressing

Ti/Mg composites can combine the benefits of Ti and Mg in terms of mechanical properties, cost, and other factors, making them highly valuable for various applications. In this study, Ti/Mg laminate composites were prepared by vacuum hot pressing at temperatures of 350 °C, 400 °C, and 450 °C for 6 h, 8 h, and 10 h, respectively. The study aimed to examine the effect of the diffusion behavior of elements and microstructure on the bonding strength of Ti/Mg laminate composites. The shear strength test results indicated that the laminated composites displayed a strong bonding strength at 400 °C, while a significant decrease in bonding strength was noted at 350 °C and 450 °C. Results of TEM analysis show that when the temperature is 350 °C, the intermetallic compound is not observed at the interface; when the temperature increased to 400 °C, a transition region along the interface is observed, and there is a Ti3Al compound in the region, the compound is uniformly distributed along the interface; when the preparation temperature is 450 °C, intermetallic compounds were observed at the interface, and the compounds were TiAl, TiAl was not uniformly distributed along the interface. EBSD analysis showed that in the Mg matrix of the composites, the distribution of coarse crystals and fine crystals was obvious due to the dynamic recrystallization, and such a distribution of grain size was also conducive to the further enhancement of the bonding strength of the composites. It can be concluded that the formation of intermetallic compounds with a continuous distribution of the transition region caused by elemental diffusion and the enhancement of the mechanical properties at the matrix are both effective in improving the bond strength of composites.

Effects of Length-to-Width Ratio on Magnetic and Microstructural Properties of Die-Upset Nd–Fe–B Magnets

In this study, the effects of the length-to-width ratio on the magnetic and microstructural properties of die-upset Nd–Fe–B magnets were examined. A die-upset magnet with a uniform shape and no significant cracking was successfully developed. During the die-upset process, the applied pressure was not uniform across the magnet and varied depending on its shape and position. In the case of the magnet with a 4:1 ratio, which had the largest length-to-width ratio, there was a higher concentration of stress at the edges compared to the center, resulting in easier grain deformation and growth at the edges, which led to the lowest remanence and (BH)max. As the length-to-width ratio approached 1:1, the grain size increased slightly, reducing the coercivity; however, the magnets maintained a uniform grain-size distribution. The change from a rectangular to a square pressing surface resulted in a more uniform stress distribution, particularly at the center and corners, which improved the consistency of the magnetic properties across different regions of the magnet. Consequently, an 11.9% enhancement in (BH)max, reaching 285.6 kJ/m3, was achieved in the 1:1 ratio die-upset magnet, which is attributed to the uniform grain size and improved grain alignment.

Back propagation neural network model for controlling artificial rocks petrophysical properties during manufacturing process

Artificial rocks are increasingly used in experiments, and it is important to make artificial rocks’ petrophysical properties similar to real rocks to obtain more valuable results. The effect of widely used five factors, grain size (GS), grain size distribution (GSD), mass fraction of cementing agent (MC), pressing pressure (PP), and pressing time (PT), on artificial rock petrophysical properties are analyzed. Three factors, GS, MC, and PP, which are suitable for establishing a quantitative model are opted. The relationships of 80 rock plugs’ petrophysical properties and manufacturing factors are studied, which indicates MC and PP are negatively correlated with porosity and permeability, and GS has a significant effect on permeability but little effect on porosity. Furthermore, a novel back propagation (BP) neural network model is proposed, which can be used to determine factor values during artificial rock manufacturing process. A series of artificial core plugs are manufactured relying on manufacturing factor values calculated by the BP neural network model, and their petrophysical properties are tested and compared with design petrophysical properties value to verify the model. Verification results show that comprehensive average error of porosity and permeability of artificial rock, including calculating error and manufacturing error, is 2.38 and 18.68%, respectively.

Holocene paleoenvironment of the Nihewan Basin, China, inferred from high-resolution luminescence dating and a multiproxy analysis of gully sediments

As a pivotal region for studying early human occupation in East Asia, the Nihewan Basin has witnessed numerous studies on Paleolithic sites and associated paleoenvironmental records. However, little attention has been given to the Holocene period, despite the basin being a crossroads for the exchange of NE China Neolithic cultures. In the central part of the Nihewan Basin, we found a gully sediment section with a thickness of ∼9 m, which exhibits clear parallel bedding throughout. The section is composed of ten sediment layers (Layers 10–1 from bottom to top), from which three distinct dark-colored soil layers (Layers 8, 4 and 2) and two erosion surfaces (between Layers 10 and 9, and Layers 2 and 1) were identified. Forty-four sediment samples from the section were optically dated, and the obtained ages were refined using Bayesian statistical modeling. The age-depth relationship and sedimentary characteristics suggest that the sedimentation process of Layers 9–2 was continuous. To reconstruct the paleoenvironment, the grain-size distribution, magnetic susceptibility, and pollen content of the sediments were analyzed. The three soil layers exhibit high magnetic susceptibility values. Based on these climatic proxies, five climate stages were recognized. From ∼12.7 to ∼6.8 ka, the climate in the basin region was cold and dry. The period between ∼6.8 and ∼5.4 ka was marked by optimal climate conditions that led to soil formation. Subsequently, the climate was colder and drier during the period of ∼5.4 – ∼4.0 ka, and transitioned to warm and wet conditions again from ∼4.0 to ∼2.7 ka. Another stage of soil formation occurred between ∼2.7 and ∼1.7 ka, during which the climate was predominantly warm and humid, albeit punctuated by a brief interval of colder and drier conditions. These climate variations coincided with cultural evolution stages within the basin, highlighting a close relationship between environmental change and human adaptation.

Charging effects on Rosetta dust measurements

ABSTRACT Dust particles released from comet 67P/Churyumov-Gerasimenko collect electrostatic charges. Their motion is influenced by the electric fields induced by the flow of the solar wind and by the charging of the Rosetta spacecraft itself. Dust grains with sufficiently low tensile strength might even be destroyed en route from the nucleus to Rosetta. A simple model of the plasma environment is discussed here to enable simultaneously following the charging and the dynamics of dust particles as a function of the heliocentric distance of the comet, the distance between Rosetta and the nucleus, the asymmetry in gas production between the northern and southern hemispheres of the nucleus, the amplitude and timing of ultraviolet flares, and the possible outbursts intermittently increasing the production rate of the comet. The electrostatic disruption, and the combination of attractive and repulsive forces between the dust grains and Rosetta might significantly alter the conclusions about the size and spatial distributions of dust grains released from 67P/Churyumov-Gerasimenko. These calculations are presented to help assess the effects of dust and spacecraft charging in the analysis and interpretation of dust measurements by Rosetta.

Quantitative mechanism of abnormal hardening behavior of Ti6Al4V alloy strengthened by ultrasonic surface rolling

In general, the outermost region of a metallic material has the highest hardness after surface mechanical strengthening. However, an abnormal surface hardening behavior was observed in Ti6Al4V alloy after the ultrasonic surface rolling process (USRP) in this work. The region with the highest surface hardening was not at the top surface but at the subsurface. By analyzing the distribution of grain size, dislocation density, texture, and kernel average misorientation (KAM) at different depths from the surface, and combining these findings with finite element analysis (FEA), the microstructural evolution underlying this abnormal surface hardening was elucidated. The microstructural characterization and FEA results indicate that the subsurface region underwent the most significant deformation. Subsequently, through the application of theoretical analysis, the potential mechanism of abnormal hardening of USRP treatment is described quantitatively for the first time. The results demonstrated that the hardening effect resulting from grain refinement was less pronounced, whereas the hardening effect resulting from dislocation pile-up was more prevalent. At the subsurface region of the USRP sample, a large number of interfaces resulted in the highest accumulation of dislocations in this area. Consequently, the subsurface region exhibited the highest microhardness, leading to the abnormal surface hardening phenomenon.

Correlation between shot peening coverage and surface microstructural evolution in AISI 9310 steel: An EBSD and surface morphology analysis

In this study, martensitic high-strength steel serves as the subject of investigation, with both conventional and severe shot peening experiments being conducted. The coverage levels for conventional shot peening (CSP) are set at 100 % and 200 %, while severe shot peening (SSP) sees levels of 800 % and 1200 %. For the first time, the use of kernel average misorientation (KAM) enables the calculation of geometrically necessary dislocation (GND) density after peening, facilitating the study of GND density distribution across different coverage and offering a method for the visual assessment of peening degree. Results reveal that, under CSP, the gradient distribution of grain size is relatively uniform, whereas SSP leads to a pronounced gradient in grain size distribution. Taking into account the heterogeneous distribution of the initial material microstructure, a gradient in grain size from the surface to the interior of the material will appear after the coverage reaches a certain value, which is 400 % for AISI 9310 steel. Compared with CSP, SSP will further reduce the surface roughness Sa and improve the surface quality. The research presented further understands the relationship between shot peening process parameters and martensitic steel microstructure, providing an important reference for revealing the strengthening mechanism and selecting reasonable process parameters.

Synthesis of bioinspired gradient MoS2/TiO2 coatings for enhancing tribological performance of titanium alloys

To enhance the tribological performance of titanium alloys under high frictional load, a MoS2/TiO2 composite coating with grain size gradient (GSG) distribution was presented. Inspired by the design principles of dental structures, the coating was fabricated through precise control of step-up voltage during plasma electrolytic oxidation (PEO). The variation in the frequency distribution of MoS2 grain sizes along the coating growth direction, ranging from approximately 43.23 ∼ 48.46 nm and 5.32 ∼ 8.16 nm, is attributed to increased energy supply and a higher degree of subcooling as the PEO voltage was elevated. The GSG coating significantly reduces the average coefficient of friction and abrasion loss by 65.44 % and 30.62 % with loads increasing to 10 N, compared with the MoS2/TiO2 coating. This improvement is attributed to the cooperative deformation of grains with varying sizes within the GSG structure under high frictional loads, which promotes strain delocalization and facilitates the formation of strain transition zones. These mechanisms effectively mitigate strain localization and ultimately achieve superior anti-friction performance. This study is essential for enhancing the broad application of titanium alloys in high-frictional environments.

River Sedimentation Due to Tin Mining Activities in Bangka Island

Sedimentation in rivers is a major issue of environmental damage in the Kepulauan Bangka Belitung Province. In the last two decades, since tin mining was carried out by the community, massive sedimentation has occurred in the river. The purpose of the study is to investigate the characteristics of sediment materials and the effects of illegal tin mining on river sedimentation on Bangka Island. Sediment characteristics can be seen from the distribution of grain size and specific gravity of the bed sediment material and the concentration of suspended sediments seen from their position along the river. Sediment grain size is classified according to the American Geophysical Union. A total of 45 sediment samples spread across 12 rivers in the district capital area on Bangka Island were collected at the end of the rainy season in 2023, and 4 more samples were added in the dry season of 2023 in the Muntok River. The MPM formula was applied to estimate bedload transport and statistical methods were used to estimate suspended sediment rates. Additionally, the sedimentation rates are estimated based on dependable continuous flow with a probability exceeding 50% (Q50%). The study’s findings indicate that Illegal tin mining in Bangka Island has a major impact on river sedimentation. The particle size distribution of bed material sediments does not align with what is typically found in nature, which often exhibits coarser particles upstream and finer downstream. Similarly, in areas downstream of tin mining operations, the concentration of suspended particles increases significantly, up to 12 times higher than natural conditions.

Complex Permittivity of Adobe Verses Frequency and Water Content

The complex permittivity of adobe is measured using a coaxial probe system verses frequency (500 MHz to 7 GHz) and water content (0% to 6%). Measurements are performed using adobe samples collected from abode bricks. The geotechnical properties of the compressed earth bricks are characterized by (1) percentage of gravel, sands, and fines; (2) Atterberg limits; and (3) grain-size distribution. The variation in adobe complex permittivity verses frequency is measured at discrete levels of water content using small adobe samples exposed to controlled levels of constant humidity in an environmental chamber. The typical water content profile verses depth for an adobe brick is also determined.

Anisotropic corrosion behavior of laser-based direct energy deposited H13 steel in molten ADC12 aluminum alloy

The immersion corrosion experiment of laser-based direct energy deposited H13 steel in ADC12 aluminum alloy melt was conducted to evaluate the demands for corrosion resistance after mold repair. The effect of the anisotropic microstructure of the deposited H13 steel on corrosion behavior was elucidated by characterizing the microstructure before and after corrosion. The results show that the microstructural heterogeneity affects the initiation, development and stabilization process of corrosion. Corrosion tends to initiate near the heat-affected zone due to the heterogeneous distribution of grain size, carbides, and dislocation density. Planes with weak microstructural heterogeneity are less likely to develop cracks in the intermetallic compounds (IMCs) layer during the corrosion development stage, thus exhibiting a slower corrosion rate. The IMCs layer of plane with weak microstructural heterogeneity stabilizes more quickly during the corrosion stabilization stage. The plane perpendicular to the build direction exhibits the highest corrosion resistance due to fewer corrosion initiation locations and the weakest microstructural heterogeneity. Furthermore, the composite structure of carbide core + Si phase shell, generated during corrosion, contributes to improving localized corrosion resistance. This study provides insights into understanding the influence of the heterogeneous microstructure from additive manufacturing on the reaction-diffusion process and offers guidance on direction selection when preparing components for applications in contact with aluminum melts using additive manufacturing techniques.

Effect of fast frequency double pulse current on microstructural characteristics and mechanical properties of wire arc additively manufactured Ti-6Al-4V alloy

This study introduces an innovative technique known as fast-frequency double pulse wire arc metal additive manufacturing (FFDP-WAAM). This method employs periodic fluctuations in arc plasma and force to enhance the stirring effect within the molten pool, resulting in the fragmentation of β grains and the formation of finer prior-β grains. The microstructure primarily comprises α', attributed to the high cooling rates and minimal heat accumulation. Compared to the conventional gas tungsten arc welding-based WAAM (CGT-WAAM) process, FFDP-WAAM significantly reduces α-variant selection, thereby achieving a more uniform α phase orientation distribution. Additionally, ultrasonic vibration in the FFDP-WAAM process facilitates recrystallization and mitigates residual strain. The tensile strength and elongation of the FFDP-WAAM specimens reached 939.2 MPa and 9.0 %, respectively, whereas the CGT-WAAM specimens showed a lower tensile strength of 830 MPa and elongation of 9.2 %. The enhanced strength, fatigue life and microhardness of Ti-6Al-4V produced by FFDP-WAAM is ascribed to the refined grain-size distribution. Furthermore, the low Schmid factor (SF) distribution and the stable triangular structure of Category I α-clusters are anticipated to contribute to the increased strength of the FFDP-WAAM-fabricated wall.

Factors influencing foraminiferal assemblages in coastal sediments of the Cross River Estuary, Southeast Nigeria, Gulf of Guinea

Estuaries are crucial coastal ecosystems facing increased pressures from human activities. The Cross River Estuary in Nigeria is a vital tropical mesotidal estuary influenced by diverse anthropogenic and natural processes. This study investigated the distribution of foraminiferal assemblages in the estuary's sediments, alongside environmental parameters such as heavy metals, pH, depth, temperature, salinity, mean grain size, and dissolved oxygen. Field sampling involved collecting 55 bottom water and sediment samples, with laboratory analyses focusing on grain-size distribution, foraminiferal identification, and heavy metal concentrations. Results indicated that heavy metal concentrations, except for iron, were within permissible limits. A total of 287 benthic foraminiferal tests representing four species were identified. These were primarily agglutinated species, with Arenoparrella mexicana and Miliammina fusca being the most abundant. Foraminiferal distribution was influenced by sediment type, salinity, and pH, rather than heavy metal concentration. Principal Component Analysis (PCA) revealed weak relationships between foraminiferal species and environmental variables, indicating limited influence of mean grain size and heavy metals on foraminiferal distribution. The study highlights the adaptability of certain foraminiferal species to a wide range of environmental conditions and underscores the need for continuous monitoring of the estuarine ecosystem to assess the impacts of ongoing anthropogenic activities. The findings provide a baseline for future environmental assessments and the use of foraminifera as bioindicators in tropical estuarine environments.

Grain-size distribution characteristics of sediments in coastal shallow waters from Van Don to Tien Yen - Ha Coi, Northwest Gulf of Tonkin, Vietnam, according to End-member modelling analysis

The study involved the collection of eighteen surface sediment samples from the coastal shallow water area from Van Don to Tien Yen - Ha Coi in the Northwestern section of the Gulf of Tonkin to analyze their particle size composition. Utilizing the EMMAgeo end-member analysis model, four characteristic particle sizes (4EM) of 0.34, 7.7, 130, and 230 µm, corresponding to clay, fine silt, and fine sand of varying sizes were identified. In conjunction with the sedimentary environment, the spatial distribution analysis of these end members allowed a detailed determination of the formation conditions and distribution of the sediment components. Clay deposits (EM1) are primarily intercalated between the islands. At the same time, fine silt (EM2) is concentrated in the northern part of the study area, transported by flows, and deposited in a low-energy environment. Fine sand sediments (EM3 and EM4) are distributed along the coast of the Van Don peninsula in the Southern part of the study area and likely formed in association with tidal-wave processes under higher energy conditions compared to the North.

Infrared emissivity of icy surfaces

Context. Most analyses of the infrared emission of Saturn’s rings and icy satellites have considered pure water ice as the constituent of regolith and particle surfaces. Visual and near-infrared observations have shown, however, that darkening and reddening contaminants are present at a fraction level of a few percent. In the spectral domain 10–2000 cm−1, water ice becomes transparent in a few windows, which in particular causes the roll-off of emissivity of icy surfaces that is observed below 50 cm−1. Their emissivity there may be affected by these contaminants. Aims. We present a quantitative global sensitivity analysis of a hybrid Mie-Hapke model to evaluate the influence of regolith properties and contaminant fraction on the infrared emissivity of icy rings or moons over this spectral range. Methods. A hybrid Mie–Hapke model of the hemispherical emissivity ε*h(Wn) was made, including various diffraction correction and mixing types with tholins or amorphous carbon grains, or grain size distributions and some anisotropy in emission. A Sobol global sensitivity analysis provided quantitative levels of importance for these factors versus wave number wn. Results. Given the a priori uncertainties, the most important factor acting on ε*h(Wn) remains the size distribution of regolith grains and the average anisotropy factor ξ. For wn> 50 cm−1, ξ, the power-law index p and the minimum amin of the size distribution are most influential. In windows of water-ice transparency (10–50, 300–600, and 900–1300 cm−1), the emissivity is also sensitive, but to a lesser extent, to the maximum grain size amax and the fraction f of contaminants, if mixed at the molecular level. Conclusions. This model provides a self-consistent tool for interpreting multi-modal observations of the thermal emission from icy surfaces. It also offers interesting insights into recent mid-infrared observations of Saturn’s rings and Jupiter’s moon Ganymede by the JWST-MIRI instrument.

Finite Element Simulation of Multi-Pass Rolling of a Pure Aluminum Target under Different Rolling Routes and Methods

By coordinating the rolling direction and mode, a multi-rolling plastic deformation process for an aluminum (Al) sputter target is proposed to achieve multiple excellent properties, including a uniform and fine grain structure and low defect risk, which are significant in producing high-quality sputtered films. In this work, therefore, DEFORM 3D 10.2 software is adopted to establish three strategies, clock-synchronous rolling, cross-synchronous rolling, and clock–snake rolling. The effect of different rolling routes and modes on the metal flow velocity (MFV), effective strain distribution (ESD), grain size distribution (GSD), damage, and rolling force (RF) are comparatively investigated. The simulation results show that clock–snake rolling can increase the MFV and effective strain by producing a deeper deformation than the others. It provides sufficient energy for dynamic recrystallization to promote grain refinement. In combination with the microstructure homogeneity promoted by the clock rolling route, the GSD from 6.5 to 44.3 μm accounts for about 80.5% of all the grains because of the fact that a randomly oriented grain region is full of high-angle grain boundaries. Compared with the synchronous rolling mode, the decrement in RF maximum reaches up to 51% during the asynchronous rolling process because component energy is consumed to form cross-sheering stress. It remarkably reduces the risk of defects, with a damage value of less than 73%, and simultaneously improves energy efficiency owing to smaller and uniform grains caused by less RF. The results obtained in this work are of great significance as they can guide practical production in the metal target industry.