Grain Size Of Perovskite Films Research Articles

Phase transition induced recrystallization and low surface potential barrier leading to 10.91%-efficient CsPbBr3 perovskite solar cells

High efficiency and long-term stability are vital for further development of perovskite solar cells (PSCs). PSCs based on cesium lead halide perovskites exhibit better stability but lower power conversion efficiencies (PCEs), compared with organic-inorganic hybrid perovskites. Lower PCE is likely associated with trap defects, overgrowth of partial crystals and irreversible phase transition in the films. Here we introduce a strategy to fabricate high-efficiency CsPbBr3-based PSCs by controlling the ratio of CsBr and PbBr2 to form the perovskite derivative phases (CsPb2Br5/Cs4PbBr6) via a vapor growth method. Following post-annealing, the perovskite derivative phases as nucleation sites transform to the pure CsPbBr3 phase accompanied by crystal rearrangements and retard rapid recrystallization of perovskite grains. This growth procedure induced by phase transition not only makes the grain size of perovskite films more uniform, but also lowers the surface potential barrier that existsbetween the crystals and grain boundaries. Owing to the improved film quality, a PCE of 10.91% was achieved for n-i-p structured PSCs with silver electrodes, and a PCE of 9.86% for hole-transport-layer-free devices with carbon electrodes. Moreover, the carbon electrode-based devices exhibited excellent long-term stability and retained 80% of the initial efficiency in ambient air for more than 2000 h without any encapsulation.

Exposed the mechanism of lead chloride dopant for high efficiency planar-structure perovskite solar cells

Although the PbCl2 has been exploited to improve the performance of perovskite solar cells, the mechanism of enhancement by the introducing PbCl2 is not fully understudied. In present work, we used the PbCl2 as a dopant to improve the perovskite film quality, we found the crystalline and grain size of perovskite film both increased with 10% molar ratio of PbCl2. The in situ time-resolved grazing incidence wide-angle X-ray scattering measurements revealed that more pre-nucleated suspended in the solution when employed the PbCl2 dopant, leading to high crystalline for perovskite film. An incorporation of the space charge limit current, photoluminescence, time-resolved photoluminescence measurements, we uncover the function of PbCl2 in reduced trap density, decreased charge recombination and enhanced carrier lifetime. As a result, the efficiency of planar-structure perovskite solar cells based on PbCl2 enhanced to as high as 19.79% with reduced hysteresis, increased by ∼23% compared to the device without PbCl2 (16.05%). We believe that this work would provide a fundamental prospective for mixed perovskite and promote its application in perovskite photovoltaics.

Passivation of interstitial and vacancy mediated trap-states for efficient and stable triple-cation perovskite solar cells

The current work reports the concurrent passivation of interstitial and oxygen vacancy mediated defect states in low temperature processed ZnO electron transport layer (ETL) via Ultraviolet-Ozone (UVO) treatment for fabricating highly efficient (maximum efficiency: 16.70%), triple cation based MA0.57FA0.38Rb0.05PbI3 (MA: methyl ammonium, FA: formamidinium, Rb: rubidium) perovskite solar cell (PSC). Under UV exposure, ozone decomposes to free atomic oxygen and intercalates into the interstitial and oxygen vacancy induced defect sites in the ZnO lattice matrix, which contributes to suppressed trap-assisted recombination phenomena in perovskite device. UVO treatment also reduces the content of functional hydroxyl group on ZnO surface, that increases the inter-particle connectivity and grain size of perovskite film on UVO treated ZnO ETL. Owing to this, the perovskite film atop UVO treated ZnO film exhibits reduced micro-strain and dislocation density values, which contribute to the enhanced photovoltaic performance of PSC with modified ZnO ETL. The modified PSCs exhibit higher recombination resistance (RRec) ∼40% compared to pristine ZnO ETL based control devices. Adding to the merit, the UVO treated ZnO PSC also demonstrates superior device stability, retaining about 88% of its initial PCE in the course of a month-long, systematic degradation study.

Phase Engineering of Perovskite Materials for High-Efficiency Solar Cells: Rapid Conversion of CH3NH3PbI3 to Phase-Pure CH3NH3PbCl3 via Hydrochloric Acid Vapor Annealing Post-Treatment.

Organometal halide CH3NH3PbI3 (MAPbI3) has been commonly used as the light absorber layer of perovskite solar cells (PSCs), and, especially, another halide element chlorine (Cl) has been often incorporated to assist the crystallization of perovskite film. However, in most cases, a predominant MAPbI3 phase with trace of Cl- is obtained ultimately and the role of Cl involvement remains unclear. Herein, we develop a low-cost and facile method, named hydrochloric acid vapor annealing (HAVA) post-treatment, and realize a rapid conversion of MAPbI3 to phase-pure MAPbCl3, demonstrating a new concept of phase engineering of perovskite materials toward efficiency enhancement of PSCs for the first time. The average grain size of perovskite film after HAVA post-treatment increases remarkably through an Ostwald ripening process, leading to a denser and smoother perovskite film with reduced trap states and enhanced crystallinity. More importantly, the generation of MAPbCl3 secondary phase via phase engineering is beneficial for improving the carrier mobility with a more balanced carrier transport rate and enlarging the band gap of perovskite film along with optimized energy level alignment. As a result, under the optimized HAVA post-treatment time (2 min), we achieved a significant enhancement of the power conversion efficiency (PCE) of the MAPbI3-based planar heterojunction-PSC device from 14.02 to 17.40% (the highest PCE reaches 18.45%) with greatly suppressed hysteresis of the current-voltage response.

Stitching triple cation perovskite by a mixed anti-solvent process for high performance perovskite solar cells

With the rapid development of organic-inorganic lead halide perovskite photovoltaics, increasingly more attentions are paid to explore the growth mechanism and precisely control the quality of perovskite films. In this study, we propose a “stitching effect” to fabricate high quality perovskite films by using chlorobenzene (CB) as an anti-solvent and isopropyl alcohol (IPA) as an additive into this anti-solvent. Because of the existence of IPA, CB can be efficiently released from the gaps of perovskite precursors and the perovskite film formation can be slightly modified in a controlled manner. More homogeneous surface morphology and larger grain size of perovskite films were achieved via this process. The reduced grain boundaries ensure low surface defect density and good carrier transport in the perovskite layer. Meanwhile, we also performed the Fourier transform infrared (FTIR) spectroscopy to investigate the film growth mechanism of unannealed and annealed perovskite films. Solar cells fabricated by using the “stitching effect” exhibited a best efficiency of 19.2%. Our results show that solvent and solvent additives dramatically influenced the formation and crystallization processes for perovskite materials due to their different coordination and extraction capabilities. This method presents a new path towards controlling the growth and morphology of perovskite films.