Thin Gold Films Research Articles

Thermo-plasmon-assisted all-optical switches based on coupled micro-cavities

Given the major applications of optical switches in the next generation electronics, plasmon assisted all-optical switch is proposed based on plasmonic micro ring arrays covered with the graphene layer. For this purpose, we use a laser writing system to fabricate micro hole arrays and cover them by plasmonic gold thin film via sputtering machine, with chemical vapor deposition method being used to produce graphene layer. After theoretically and experimentally evaluating the plasmonic substrate, we use ellipsometric method to characterize the optical modes of the samples. Furthermore, the all-optical and gated switches response is recorded for the fabricated sample. Our results show phase delay plasmon induced switching as well as thermo-plasmonic affected benefit for the proposed switching structure in the order of 0.29 s (duty cycle). The suggested switch with its low power consumption, small size, and easier and low-cost fabrication process can open new insight into plasmon-assisted all-optical switches.

The Simulation of Proton Beam Passage through Thin Gold Films

The Simulation of Proton Beam Passage through Thin Gold Films

Nonlinear optical properties of gold with intense femtosecond laser excitations above the damage threshold

The nonlinear optical properties of gold thin films have been studied under the irradiation of destructive laser pluses. The transmissivity and the reflectivity of a 100-nm-thick gold film are measured with femtosecond laser irradiations up to 106 J/m2 fluence, which is much higher than the damage threshold of gold. The nonlinearity is calculated with Fresnel loss equations. The real part of the complex refractive index is calculated to have a peak at ∼10 kJ/m2, which is close to the damage threshold. The complex third-order nonlinear susceptibility χ3 is estimated to be (4.95 − 2.02i) × 10−21 m2/V2, which agrees with the trend in previous reports that it decreases as the pulse duration decreases. This nonlinearity is further studied with a plasmon-photon exchange (PPE) model, where laser induced plasmons and absorbed photons are strongly correlated. The result of the simulation with the PPE model is in good agreement with the experimental transmissivity above the damage threshold. The model predicted an interaction time between photons and plasmons to be about 500 fs. This model is found to be essential in understanding such nonlinear optical processes under both extremely high and conventionally low laser irradiations.

Flexible Wearable Ti3C2Tx Composite Carbon Fabric Textile with Infrared Stealth and Electromagnetic Interference Shielding Effect

AbstractTi3C2Tx materials have been developed to have application space in many fields, but there are not many works that can be compatible with infrared (IR) stealth and electromagnetic interference (EMI) shielding at the same time. To realize the multiband high EMI shielding of Ti3C2Tx materials, and to achieve stealth effect in the IR band, in this work, a composite textile is prepared by combining the Ti3C2Tx material with a carbon cloth and sputtering a very thin gold film on the surface. This composite textile can realize high EMI shielding compatible with IR stealth, in which the EMI shielding efficiency for microwave Xa‐band (8GHza‐12.4GHz) is up to 71.8 dB, for microwave Kaa‐band (26.5GHza‐40GHz) is up to 75.02 dB, and for terahertza‐band is about 30 dB. IR emissivity is as low as 0.1, and the lowest emissivity under a certain temperature reaches 0.07, which can withstand a high temperature of 500 °C. In addition, this composite textile has flexible and bendable wear. The thickness of the whole textile is about 400 µm, of which the Ti3C2Tx material thickness is only about 10 µm, the thinnest reaches 2 µm. Such a textile can be used in both people's livelihood and military applications, which has far‐reaching significance.

One-dimensional porous silicon photonic crystals for chemosensors: Geometrical factors influencing the sensitivity

One-dimensional photonic crystals with microcavity were prepared to be used as optical chemosensors. The experimental reflectance of the as-etched devices immersed in solvent solutions appear greater than the theoretical one. The fitting procedure of the experimental data using the transfer matrix method together with the Looyenga effective medium approach reveals that the deviation of the experimental data occurs because of the expansion-contraction effect of the high and low porosity layers, respectively, caused by the presence of the solvent into the porous matrix and is proportional to the solvent effective refractive index. Due to this phenomenon, the sensitivity of the as-etched photonic crystals increases about two times but is not stable because of the aging effect. To avoid this effect, the photonic crystal structures were passivated by thermally silicon oxide growing, gold thin film and titanium oxide deposition. After thermal treatment in an air environment, the optical response achieves its stabilization even after long storage times, thus showing the importance of the passivation procedure. Among them, the passivation by TiO2 shows better performance and lower loss in sensitivity in comparison to the as-etched devices.

Optical Constants and Optical Anisotropy of Ultrathin Gold Films

Continuous and homogeneous thin gold films are fabricated on Si–SiO2 substrates using an additional seed layer based on Cu oxide or oxidized Cu. The optical properties of these gold films with thicknesses from 3 to 50 nm are studied with the help of variable angle spectroscopic ellipsometry. The optical constants and the dielectric functions of thin Au films in the wavelength range of 240–1700 nm are extracted by fitting measured ellipsometric data using the Fresnel isotropic and anisotropic models. By applying the Drude approximation to the infrared range, values of the plasma frequency ωp and relaxation time τ are obtained as a function of film thickness. It is found that plasma frequency ωp of the gold films is mostly constant in the thickness range of 3–50 nm with an average being close to the bulk value ωp ≈ 8.45 eV. The relaxation time decreases dramatically from the bulk values of τ ≈ 14 fs to τ ≈ 2 fs for gold films of 3 nm in an agreement with the confinement effect. It is established that the thinnest gold films (≈3 nm) are described better by an anisotropic layer and the underlying reasons for such optical anisotropy are discussed.

Light blocking and phase modulation based on thermo-plasmonic hotspots in WS2 monolayer

Here we demonstrate light blocking and phase modulation in nano-plasmonic donate shape rings based on the thermo-plasmonic effect in these structures. For this purpose, we use a laser writing system to fabricate nanohole arrays and cover them with plasmonic gold thin film via a sputtering machine. The chemical vapor deposition method is also used to produce a WS2 layer, which is suitable for light blocking and phase modulation due to the nonlinearity of this two-dimensional material. After theoretically and experimentally evaluating the plasmonic donate-shaped substrate, we use the ellipsometric method to characterize the optical modes of the samples and record the switching manner and light-blocking phenomena under the probe laser excitation set to 980 nm. Our results show phase modulation based on the thermo-plasmonic effect of nano gap in donated double rings and light blocking by thermal expansion of the WS2 layer, which can open new insight into plasmon and two-dimensional material-based devices.

Emergence of liquid following laser melting of gold thin films.

X-ray structural science is undergoing a revolution driven by the emergence of X-ray Free-electron Laser (XFEL) facilities. The structures of crystalline solids can now be studied on the picosecond time scale relevant to phonons, atomic vibrations which travel at acoustic velocities. In the work presented here, X-ray diffuse scattering is employed to characterize the time dependence of the liquid phase emerging from femtosecond laser-induced melting of polycrystalline gold thin films using an XFEL. In a previous analysis of Bragg peak profiles, we showed the supersonic disappearance of the solid phase and presented a model of pumped hot electrons carrying energy from the gold surface to scatter at internal grain boundaries. This generates melt fronts propagating relatively slowly into the crystal grains. By conversion of diffuse scattering to a partial X-ray pair distribution function, we demonstrate that it has the characteristic shape obtained by Fourier transformation of the measured F(Q). The diffuse signal fraction increases with a characteristic rise-time of 13 ps, roughly independent of the incident pump fluence and consequent final liquid fraction. This suggests the role of further melt-front nucleation processes beyond grain boundaries.

Detection of environmental nanoplastics via surface-enhanced Raman spectroscopy using high-density, ring-shaped nanogap arrays.

Micro- and nano-plastics (MNPs) are global contaminants of growing concern to the ecosystem and human health. In-the-field detection and identification of environmental micro- and nano-plastics (e-MNPs) is critical for monitoring the spread and effects of e-MNPs but is challenging due to the dearth of suitable analytical techniques, especially in the sub-micron size range. Here we show that thin gold films patterned with a dense, hexagonal array of ring-shaped nanogaps (RSNs) can be used as active substrates for the sensitive detection of micro- and nano-plastics by surface-enhanced Raman spectroscopy (SERS), requiring only small sample volumes and no significant sample preparation. By drop-casting 0.2-μL aqueous test samples onto the SERS substrates, 50-nm polystyrene (PS) nanoparticles could be determined via Raman spectroscopy at concentrations down to 1μg/mL. The substrates were successfully applied to the detection and identification of ∼100-nm polypropylene e-MNPs in filtered drinking water and ∼100-nm polyethylene terephthalate (PET) e-MNPs in filtered wash-water from a freshly cleaned PET-based infant feeding bottle.

Long-Focusing Device for Broadband THz Applications Based on a Tunable Reflective Biprism.

THz radiation has assumed great importance thanks to the efforts in the development of technological tools used in this versatile band of the electromagnetic spectrum. Here, we propose a reflective biprism device with wavelength-independent long-focusing performances in the THz band by exploiting the high thermo-mechanical deformation of the elastomer polydimethylsiloxane (PDMS). This deformation allows for achieving significant optical path modulations in the THz band and effective focusing. The surface of a PDMS layer is covered with a gold thin film acting as a heater thanks to its absorption of wavelengths below ~500 nm. An invariance property of the Fresnel integral has been exploited to experimentally verify the THz performances of the device with an ordinary visible laser source, finding excellent agreement with the theoretical predictions at 1 and 3 THz. The same property also allowed us to experimentally verify that the reflective biprism focus has a longitudinal extension much greater than that exhibited by a benchmark convex cylindrical mirror with the same optical power. The device is thermo-mechanically stable up to a heating power of 270 mW, although it might be potentially exploited at higher powers with minor degradation of the optical performances.

Characterization of balsam sulfide via pyrolysis-gas chromatography-mass spectrometry/sulfur chemiluminescence detection and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry.

Balsam sulfide, produced by the reaction of turpentine/rosin and sulfur, has been used as one of the raw materials of liquid gold to decorate ceramics and tableware with thin gold film for more than 100years. The characterization of balsam sulfide is still insufficient because of its compositional complexity. In this study, balsam sulfide was characterized using pyrolysis-gas chromatography (Py-GC)-mass spectrometry (MS) and Py-GC with sulfur chemiluminescence detection (SCD) as well as matrix-assisted laser desorption/ionization time-of-flight MS (MALDI-TOFMS). Py-GC-MS/SCD analyses of balsam sulfide and its model samples revealed that the low molecular weight reaction products were mainly composed of compounds of one α-pinene unit reacted with 1-3 sulfur atoms. In the analysis of the high molecular weight components by MALDI-TOFMS, the products of two or three α-pinene units crosslinked by sulfur atoms were observed. It was found that dehydrogenation reaction proceeded gradually with the increase in the reaction time.

Creep-dominated fatigue of freestanding gold thin films studied by bulge testing

Although metallic thin films are widely used in microelectronics, their high-cycle fatigue properties are not well-understood. Cyclic testing was conducted on 150-nm thick freestanding gold thin films using nominal stress amplitudes between 50 and 150 MPa at 23–100 °C. As expected, lifetime decreases with increasing stress amplitude and temperature. The strain at failure hardly exceeds 1.5%, which is in agreement with previous studies on metallic thin films. The hysteresis stress-strain curves suggest that strain accumulates mostly due to cyclic creep. Based on this observation, we calculated the stress exponent n and activation energy Q – which are typical creep parameters – from the apparent steady-state strain rate observed during cyclic testing. Comparison to preexisting creep bulge tests show that the higher the temperature, the more pronounced the influence of creep on the fatigue behavior. Especially at 100 °C, creep mechanisms clearly dominate. At lower temperatures (23 °C) the data indicate that creep still plays a role, but intrinsic cycling effects become more pronounced. That leads us to postulate that the fatigue lifetime of gold thin films is closely connected to their creep properties.

Quantitative measurement of CA 15-3 cancer biomarker using an electrochemical aptasensor based on the electrodeposition of Au thin film on cauliflower-like rGO-MoS2 nanocomposite.

The present research was conducted to design and construct an electrochemical aptasensor for evaluating carbohydrate antigen 15-3 (CA15-3) as a biomarker for breast cancer. The aptasensor has been fabricated by a gold thin film (AuTF) electrodeposited on a cauliflower-like reduced graphene oxide-molybdenum sulfide nanocomposite (rGO-MoS2). The modified electrode's surface was used to immobilize the thiolated aptamer, which was subsequently treated with CA 15-3 antigen. The aptasensor fabrication process was assessed using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). This research also applied EIS to the quantitative measurement of CA 15-3 antigen by the proposed aptasensor. The interfacial charge transfer resistance (Rct) alteration before and after incubation of CA 15-3 by theimmobilized aptamer was considered a signal for the quantitative measurement of CA 15-3. A linear concentration ranging from 5.0 to 200.0 U mL-1 with a detection limit of 3.0 × 10-1 U mL-1 was obtained for CA 15-3 using the EIS method. This designed aptasensor indicates satisfactory repeatability and stability, good selectivity, and high sensitivity. Moreover, clinical samples were assayed by the prepared aptasensor and compared with the ELISA method, yielding acceptable results. Therecovery and relative standard deviation (RSD) of CA 15-3 in human serum samples were in the range 95.0 to 107.0% and 3.5 to 7.5%, respectively.

(Invited) Probing and Utilizing Hot Carriers for Plasmonic Photoelectrochemical Processes

The detection of hot electrons and understanding the correlation between hot electron generation and surface phenomena are challenging questions in the surface science and catalysis community. Hot electron flow generated on a gold thin film by photon absorption (or internal photoemission) appears to be correlated with localized surface plasmon resonance. It has been found that the hot electron flux generated under photon absorption and exothermic chemical reaction is the major mediator of energy conversion process [1-3]. In this talk, I introduce the research direction to attempt to detect the surface plasmon driven hot carrier at the nanometer scale by using scanning probe microscopy. To detect and utilize the hot electron flows at the macroscale level, the metal-semiconductor nanodiodes were constructed. At the nanometer scale, we utilized photoconductive atomic force microscopy to observe photoinduced hot electrons on a triangular Au nanoprism on n-type TiO2 under incident light. This is the direct proof of the intrinsic relation between hot electrons and localized surface plasmon resonance. We observed surface plasmon induced hot hole by using the system of Au nanoprism on p-type GaN [4]. I will discuss the impact of hot carriers in the photocatalytic activity under photoelectrochemical water splitting by using Au-based plasmonic nanostructures [5].

Dual-Dewetting Process for Self-Assembled Nanoparticle Clusters in Wafer Scale.

Plasmonic molecules, which are geometrically well-defined plasmonic metal nanoparticle clusters, have attracted significant attention due to their enhancement of light-matter interactions owing to a stronger electric field enhancement than that by single particles. High-resolution lithography techniques provide precise positioning of plasmonic nanoparticles, but their fabrication costs are excessively high. In this study, we propose a lithography-free, self-assembly fabrication method, termed the dual-dewetting process, which allows the control of the size and density of gold nanoparticles. This process involves depositing a gold thin film on a substrate and inducing dewetting through thermal annealing, followed by a second deposition and annealing. The method achieves a uniform distribution of particle size and density, along with increased particle density, across a 6-inch wafer. The superiority of the method is confirmed by a 30-fold increase in the signal intensity of surface-enhanced Raman scattering following the additional dewetting with an 8 nm film, compared to single dewetting alone. Our findings indicate that the dual-dewetting method provides a simple and efficient approach to enable a variety of plasmonic applications through efficient plasmonic molecule large-area fabrication.

A Polished-D-Shape SPR-Based Photonic Crystal Fiber Sensor with High Sensitivity for Measuring Refractive Index

In the correspondence, a novel polished-D-shape photonic crystal fiber sensor structure on the basis of surface plasmon resonance is proposed for measuring analyte refractive index. With the help of the finite element method, sensing performances of the structure have been analyzed through numerical simulations along with a step-by-step optimization . In this design, different capillaries are gathered and processed to form a D-shape silica structure and nano-scale gold material is coated on the flattened surface. With utilization of a thin gold film and solid silica background, the resonance effect is excited and the loss curve has red shift along with an increase in refractive index, which is applied for sensing. From the simulation and calculation results, the final sensor structure achieves the optimal performance where values of maximum and average sensitivity reach 32,000 and 12,167 nm/RIU along with a sensing coverage of refractive index from 1.26 to 1.32. Also, the proposed design obtains a range of resonant wavelength from 1810 to 2540 nm. We believe the proposed sensor can be a potential candidate for organic and biological detection and related applications.

Programmable nanophotonic planar resonator filter-absorber based on phase-change InSbTe

Reconfigurable plasmonic-photonic electromagnetic devices have been incessantly investigated for their great ability to optically modulate through external stimuli to meet today's emerging needs, with chalcogenide phase-change materials being promising candidates due to their remarkably unique electrical and optics, enabling new perspectives in recent photonic applications. In this work, we propose a reconfigurable resonator using planar layers of stacked ultrathin films based on Metal-dielectric-PCM, which we designed and analyzed numerically by the Finite Element Method (FEM). The structure is based on thin films of Gold (Au), aluminum oxide (Al2O3), and PCM (In3SbTe2) used as substrate. The modulation between the PCM phases (amorphous and crystalline) allows the alternation from the filter to the absorber structure in the infrared (IR) spectrum (1000–2500 nm), with an efficiency greater than 70% in both cases. The influence of the thickness of the material is also analyzed to verify tolerances for manufacturing errors and dynamically control the efficiency of transmittance and absorptance peaks. The physical mechanisms of field coupling and transmitted/absorbed power density are investigated. We also analyzed the effects on polarization angles for Transversal Electric (TE) and Transversal Magnetic (TM) polarized waves for both cases.

Metasurface for broadband coherent Raman signal enhancement beyond the single-molecule detection threshold

Broadband enhancement of Raman signals is vital for molecular spectroscopy and sensing applications. However, typically, there is a compromise between the resonance width and the local field enhancement factors. Here, we merge the broadband open plasmonic cavity concepts with the geometry exploiting narrow gaps and a reflecting layer. This results in a metasurface design that maintains substantial electric field confinement in the gap volume accompanied by a broad spectral response. The confined field is enhanced through constructive interference between the plasmonically enhanced illuminating beam and the field reflected at the bottom layer. The resulting field can interact with analyte molecules and support Raman scattering. With an optimized metasurface geometry involving a pair of gold nanodisks and a thin gold film, we demonstrate numerically that our metasurface can simultaneously enhance Raman signals from various molecular species, potentially resulting in unprecedented signal intensities enhanced by up to 20 orders of magnitude, facilitating molecular detection and identification. Our design offers a practical and promising solution for improving the sensitivity of Raman techniques and has significant implications for the field of nonlinear optical spectroscopy. Moreover, our metasurface is compatible with current fabrication technologies, making it suitable for various applications in sensing and imaging.

Design of a Biaxially Stretchable Microstrip Antenna Enabled by Buckled Au Thin Film on an Elastomeric Substrate

Wearable wireless biomedical electronics enable monitoring and wireless transmission of patient physiological and pathological signals to provide remote guidance for appropriate diagnosis and treatment. As a core component, the antenna must be flexible and stretchable to adapt to the complex mechanical deformations (e.g., stretching, bending, and twisting) induced by human motions. This work proposes a biaxially stretchable microstrip antenna based on buckled gold thin films bonded on an elastomeric substrate. A simplified analytic model validated by simulations and experiments is established to investigate the biaxial buckling behaviors of the thin films within 10% tensile strains. The properties, including resonance frequency, bandwidth, and radiation pattern of the fabricated biaxially stretchable microstrip antenna under various stretched states, are studied by combining experiments and finite element analysis. The effects of biaxial tensile deformations on the resonance frequency, bandwidth, and radiation properties are discussed. Results show that the designed microstrip antenna has a relatively stable performance under both natural and deformed states within 10% of uniaxial and biaxial tensile strains, which enables the designed antenna to have broad application prospects in wearable wireless medical devices for stable transmission of signals between body-worn sensors and terminals, especially for situations accompanied with complex deformations.

Thermal Instability of Gold Thin Films

The disintegration of a continuous metallic thin film leads to the formation of isolated islands, which can be used for the preparation of plasmonic structures. The transformation mechanism is driven by a thermally accelerated diffusion that leads to the minimalization of surface free energy in the system. In this paper, we report the results of our study on the disintegration of gold thin film and the formation of nanoislands on silicon substrates, both pure and with native silicon dioxide film. To study the processes leading to the formation of gold nanostructures and to investigate the effect of the oxide layer on silicon diffusion, metallic film with a thickness of 3 nm was deposited by molecular beam epitaxy (MBE) technique on both pure and oxidized silicon substrates. Transformation of the thin film was observed by low-energy electron microscopy (LEEM) and a scanning electron microscope (SEM), while the nanostructures formed were observed by atomic force microscope (AFM) method. Structural investigations were performed by low-energy electron diffraction (LEED) and X-ray photoelectron spectroscopy (XPS) methods. Our experiments confirmed a strong correlation between the formation of nanoislands and the presence of native oxide on silicon substrates.