Glass Fiber Research Articles

Effects of Dolomite Geopolymer Filler on Mechanical Properties of Glass Fibre Reinforced Epoxy Composite

Effects of Dolomite Geopolymer Filler on Mechanical Properties of Glass Fibre Reinforced Epoxy Composite

A review on serviceability of foam concrete

In the face of the present global warming crisis, building energy conservation and emissions reduction have gained increasing attention. In the sustainable development of buildings, foam concrete has become increasingly popular in the construction industry due to its excellent thermal insulation, sound insulation and fire resistance. Foam concrete employed in buildingand construction (used as either a structural or non-structural member) must meet certain serviceability criteria. This paper reviews the serviceability of ordinary Portland cement (OPC) foam concrete, geopolymer foam concrete (GFC), sulphoaluminate cement (SAC) foam concrete, magnesium phosphate cement (MPC) foam concrete and limestone calcined clay cement (LC3) foam concrete, to include drying shrinkage, creep, thermal conductivity, water absorption and acoustic properties. Subsequently, it is proposed to change the initial curing conditions to reduce drying shrinkage, add glass fiber and basalt fiber to improve creep performance, increase heat flow direction resistance and extend the thermal conduction path to reduce thermal conductivity, control slump flow to regulate water absorption, and combine sound absorbing foam concrete with sound reflecting materials to achieve a comfortable and low noise living environment. Finally, ideas and suggestions for future work are proposed.

Mechanical properties and damping ratio of gradient polymer concrete for damping beam structure

AbstractDue to its higher overall performance than ordinary concrete, polymer concrete (PC) beam has been widely used in the field of structural engineering. However, it is widely recognized that PC cannot simultaneously achieve the highest mechanical strength and optimal damping performance to reduce vibration during its long‐term service lifetime. To address this contradiction, the effect of various diluents contents on the overall performance of PC was investigated first in this investigation. Experimental findings revealed that the bending strength of PC exhibits an initial increase followed by a decrease with an increment of diluents, while its damping ratio displays an inverse trend. To obtain excellent overall performance (higher flexural strength and damping ratio) of PC, gradient PC has been manufactured by horizontal partition casting process (HPCP) and stereoscopic layered casting process (SLCP). Experimental results demonstrated that the gradient PC manufactured by HPCP exhibited better overall performance compared to SLCP. Furthermore, the graphite and carbon fiber were incorporated into the above gradient PC, and experimental results revealed that the incorporated graphite and carbon fiber can further increase the overall performance of the above gradient PC. Similarly, the incorporation of glass fiber cloth and carbon fiber cloth, along with surface treatment, significantly enhanced the overall performance of PC. The significance of this study lies in enhancing the comprehensive performance of PC beam structures, thus broadening its utilization scope within structural engineering.

Interlaminar fracture properties of UV and plasma‐treated glass fiber epoxy composites

AbstractDespite the low density and high specific strength properties, the fiber‐reinforced composites are characterized by a relatively low interlaminar fracture toughness and their ultimate properties are strongly affected by the fiber matrix adhesion. This study aims to investigate the influence of fiber surface treatments, such as UV and atmospheric plasma, and of the interfacial shear strength, on the flexural properties and Mode I interlaminar fracture toughness of glass fiber epoxy composites. The vacuum‐assisted resin infusion technique is used for the composite fabrication. Scanning Electron Microscopy analysis is used to observe and to explain the changes in the morphology of the fibers after surface treatment. Remarkably, the results showed an overall reduction in the mechanical properties. The interfacial shear strength values of the UV and plasma‐treated samples were reduced by 34.9% and 49.5% respectively. The flexural strength was reduced by 7.9% and 5.9% respectively. The Mode I fracture toughness values for the UV and plasma‐treated samples were also reduced by 49.8% and 62.2% respectively.Highlights UV and plasma treatments were performed on glass fibers to improve performance. Push‐out tests were carried out to evaluate fiber/matrix adhesion. An aerospace grade epoxy resin curing in thermal press‐clave was used. Mechanical tests related Interfacial Shear Strength to composites performance.

Investigation of the effect of symmetrical hybrid stacking on drilling machinability of unidirectional CFRP, GFRP and hybrid composites: Drilling tests and damage analysis

Fiber-reinforced plastics are undoubtedly superior to metals in many sectors due to their advantageous properties. Especially carbon fiber reinforced plastics (CFRP) and glass fiber reinforced plastics (GFRP) are widely used in industry. Although CFRP offers higher strength, its use is limited due to its high cost. However, with hybridisation, it is possible to produce composites that will provide sufficient strength at lower cost. The mechanical behaviour of hybrid composites may be different compared to glass or carbon composites, as well as the damage behaviour during machining. In this study, the influence of hybrid stacking in drilling hybrid composites was investigated. The results showed the hybrid stacking, especially the position of the carbon plate, has a significant impact on the force generation and damage formation in the drilling. Although stacking the carbon layer at bottom caused an increase in thrust forces, it reduced the damage formation at the hole exit.

Glass fiber reinforced PA6 composites with high strength and high flowability by hyperbranched polyesters

Glass fiber reinforced <scp>PA6</scp> composites with high strength and high flowability by hyperbranched polyesters

Mechanical properties investigation of hybrid TI3C2TX MXene and carbon nanotube reinforced glass fiber epoxy composites

Mechanical properties investigation of hybrid TI3C2TX MXene and carbon nanotube reinforced glass fiber epoxy composites

Mode II fracture behavior of glass fiber composite-steel bonded interface–experiments and CZM

The dominant failure mode was characterized as debonding in the novel non-welded wrapped composite joint made with GFRP composites wrapped around steel sections. Glass fiber composite-steel three-point end notched flexure (3ENF) and four-point end notched flexure (4ENF) specimens were utilized to experimentally investigate mode II fracture behavior of this composite-steel bonded interface. Two new methods were proposed with the help of digital image correlation (DIC) technique to quantify fracture data during the tests: 1) the “shear strain scaling method” to quantify the crack length a; 2) the asymptotic analysis method based on the longitudinal displacement distribution along the height of the specimen at the pre-crack tip to quantify the crack tip opening displacement (CTOD). To numerically simulate the mode II fracture behavior, a four-linear traction-separation law was proposed in the cohesive zone modeling (CZM) where the softening behavior with a plateau was defined by the authors between traditionally considered initiation and fiber bridging behavior. The experimental and numerical approaches were validated mutually through good matches between the test and FEA results. 3ENF test provided good insight into softening behavior while 4ENF contributed to quantification of fiber bridging. These findings contribute to a more comprehensive characterization and understanding of the ductile fracture behavior of bi-material bonded joints, especially in mode II failure scenarios.

Repairability of rubber-backed vitrimer composites under variations of impact damage

This study evaluates the effectiveness of rapid heat pressing repair on composites made of vitrimer matrix, a reshapable and recyclable polymer, subjected to varying degrees of impact damage. Two types of composites were fabricated for impact testing: randomly oriented glass fiber reinforced vitrimers (GFRV) and woven carbon fiber reinforced vitrimers (CFRV). Izod pendulum impact tests were conducted on samples along both the thickness and width. Impacts with varying energy levels were applied to induce different degrees of damage, allowing for the assessment of impact strength degradation and repair effectiveness. Additionally, a rubber adhesive layer was applied to the back of composites to quantitatively measure the increase in energy absorption and its effect on repair performance. The findings demonstrate the potential of rapid heat pressing repair in restoring the mechanical integrity of vitrimer composites and highlight the influence of a rubber adhesive layer in enhancing energy absorption and repair efficacy.

Investigation of the Mechanical Properties of Hybrid E-Glass and Mohair Fiber Reinforced Epoxy Composites

Natural fiber composites have significant potential to replace traditional materials used in industries due to their excellent tensile strength, stiffness, low specific weight, and superior thermal and insulating properties. Mohair fiber, also known as the Noble fiber and the Diamond fiber, is obtained from the Angora goat, an animal of Tibetan origin. Renowned for its brilliant luster and resilience, Mohair is a symbol of luxury and exclusivity. The primary objective of this study is to manufacture and test a new natural fiber composite that could potentially outperform existing materials in real-world applications. Specifically, the study aims to investigate the mechanical properties of this composite. Mohair has previously been identified as a fiber many times stronger than a strand of steel of similar dimensions. Incorporating these highly desirable properties of Mohair into an epoxy matrix is one of the novel aspects of this research. The testing procedure begins with the preparation of ASTM molds, concurrent treatment of the fibers, and the preparation of the binding material. Specimens are created both with and without the addition of electrical glass (E- glass) fibers. The next phase is curing, during which the epoxy is allowed to solidify, forming strong bonds. Once developed and cured, the composites are removed from their molds and undergo post-processing and finishing techniques. This study aims to understand the tensile and flexural characteristics of natural fiber composites reinforced with epoxy. Three fiber orientations—uniaxial, biaxial, and criss-cross—are employed to assess the changes in the mechanical properties of the composites. The results indicate that adding E-glass fibers in alternating layers of the composite significantly enhances both tensile and flexural strength. Statistically, the addition of the biaxial arrangement of fibers with E-glass fibers results in an 18.47% improvement in ultimate tensile strength, while the maximum flexural strength increases by 49.90%. Furthermore, the topography of the cracked surface is examined using field emission scanning electron microscopy, and the breaking of the fibers in all three directions is studied.

Optimization of Reverse Transcription Loop-Mediated Isothermal Amplification for In Situ Detection of SARS-CoV-2 in a Micro-Air-Filtration Device Format.

The Coronavirus disease 2019 (COVID-19) pandemic has supercharged innovation in the field of molecular diagnostics and led to the exploration of systems that permit the autonomous identification of airborne infectious agents. Airborne virus detection is an emerging approach for determining exposure risk, although current methods limit intervention timeliness. Here, we explore reverse transcription loop-mediated isothermal amplification (RT-LAMP) assays for one-pot detection of Severe acute respiratory syndrome Coronavirus 2 (SARS-CoV-2) (SCV2) run on membrane filters suitable for micro-air-filtration of airborne viruses. We use a design of experiments statistical framework to establish the optimal additive composition for running RT-LAMP on membrane filters. Using SCV2 liquid spike-in experiments and fluorescence detection, we show that single-pot RT-LAMP on glass fiber filters reliably detected 0.10 50% tissue culture infectious dose (TCID50) SCV2 per reaction (3600 E-gene copies) and is an order of magnitude more sensitive than conventional RT-LAMP.

Evaluating energy efficiency and environmental sustainability in fiberglass prefabricated modular structures

Fiberglass (FG) modular buildings are gaining increasing attention in the construction industry due to their adaptability, and potential for cost and time savings. This study compares the FG modular, house-like cubicles to concrete counter parts with respect to the environmental impacts and cost. The scope of the study encompasses the production and operational phase, especially air conditioning (AC) systems in hyper-arid climates. The effectiveness of insulation, quantified through R-value calculations, is evaluated across varying insulation thicknesses using Life Cycle Assessment (LCA). The results indicate that AC energy requirements significantly contribute to the climate change impact (CCH), accounting for 77 % and 90.5 %, in concrete and FG modules respectively. FG modules exhibit significantly higher environmental impacts compared to concrete modules in agricultural land occupation (+142.7 %), terrestrial ecotoxicity (+80.6 %), and urban land occupation (+66 %). Employing Net Present Value (NPV), the annual cost for FG and concrete modules was USD 963.9 and USD 550.8 per year, respectively. Sensitivity analysis indicates that increasing insulation (+5.00 cm) in FG modules reduces that annual cost due to cooling by 16.55 %, reduces CCH by 59.47 % but increases metal depletion by 130 %. This signifies the importance of incorporating the use phase when evaluating innovative building materials and methods.

Rehabilitation and reinforcement of cracked pavements using crack sealers and composite patches

Cracking is a significant concern for pavements and should be appropriately treated during road, highway, and runway rehabilitation. This study investigates the behavior of asphaltic materials under tensile and shear loading modes in intact, fractured, and repaired conditions. With this aim, several methods and materials are utilized for repairs, such as poring adhesive into the crack (using bitumen, neat epoxy resin, and polymer concrete adhesives) and patching the crack with textile (by glass fiber and epoxy resin or bitumen). These tests were conducted at +10 °C, with a three-point bending loading configuration, the same as the actual loading configuration of pavements. Criteria such as failure load, failure work, and post-failure work, as well as failure patterns, were assessed to assess the effectiveness of repairs. Numerical analysis was also performed, and a constitutive model was presented. The ultimate tensile capacity of the cracked specimen is measured at 63 % lower than the intact condition (778 N). The ultimate tensile load of the bitumen-repaired specimen is higher than that of the cracked specimen, but it is still 11 % lower than that of the intact condition. The ultimate tensile capacity of epoxy resin repaired and polymer concrete repaired specimens are 88 % and 79 % higher than the intact specimen (about 1400 N). The ultimate tensile load of the fabric patch reinforced specimen that used bitumen as the adhesive is 38 % higher than the intact specimen (1075 N), while for the case of using the epoxy resin adhesive, this value is 258 % (2788 N). Observations of tensile failure patterns show that, because bitumen is viscoelastic, failure in bitumen-repaired specimens happens in bitumen necking mode and starts at the repaired crack tip. In other cases, the failure occurred far from the pre-crack plane.

Effect of atomic oxygen and vacuum thermal aging on graphene and glass fibre reinforced cyanate ester-based shape memory polymer composite for deployable thin wall structures

Deployable components and structures are a crucial part of space exploration. Due to fewer parts, low weight and cost, shape memory polymers (SMPs) and their composites (SMPCs) are considered ideal candidates for this. However, lower thermal stability and poor durability in the space environment have limited their applicability. This research work details the development of Graphene Nanoplatelets (GNP) filled Glass Fibre (GF) reinforced cyanate ester-based SMPC with 0/90° and ±45° sandwich fibre lay-up configuration capable of multidirectional shape programming. The SMP matrix was synthesised by mixing Cyanate Ester and Polyethylene Glycol (PEG) with added GNP. SMPC was fabricated by pouring the SMP mixture into a pre-prepared glass mould with the added GF layers. The synthesised SMPC showed shape programming and recovery at 169.01 ± 0.62 °C and stable thermomechanical properties at the temperature of 130 °C. Durability tests at extreme environmental conditions including Atomic Oxygen exposure, thermal vacuum aging, and elevated-temperature behaviour tests were conducted as these tests evaluate the durability and applicability of the SMPC for use in Earth's orbits and lunar environments. The performances of the samples before and after durability tests were measured through mechanical tests, shape memory effect tests and a series of characterisation methods such as microscopic image analysis, FTIR and dynamic mechanical analysis. According to the results, AO exposure affected the SMPCs by eroding their surface. There were no changes in the chemical structure of the SMPC yet the thermomechanical, mechanical and shape memory properties were decreased without compromising their safe operational levels such as storage onset temperatures (128.79 ± 3.08 °C), maximum tensile stress (114.99 ± 21.52 MPa), shape fixity (100 %) and recovery ratios (100 %). The erosion resistance of the GNP-filled SMPCs was improved with ∼54.35 % less erosion than the SMPC without GNP. The vacuum thermal aging slightly slowed shape recovery from 31.17 % to 8.32 % at 160 °C due to PEG crosslink degradation, however, 100 % shape recovery was achieved at the end. Further durability tests under cryogenic temperatures and effects after vacuum thermal cycles are warranted to observe the synergistic effect on the SMPC for future developments. Exploring the scalability and additive manufacturability of the developed SMPC can be advantageous in the future while mitigating challenges such as complex shape programming, long-term materials degradation, resource efficiency and compliance with safety standards.

The Influence of Hemp Fibers (Cannabis sativa L.) on the Mechanical Properties of Fiber-Gypsum Boards Reinforcing the Gypsum Matrix.

The modern construction industry is looking for new ecological materials (available, cheap, recyclable) that can successfully replace materials that are not environmentally friendly. Fibers of natural origin are materials that can improve the properties of gypsum composites. This is an important issue because synthetic fibers (hardly biodegradable-glass or polypropylene fibers) are commonly used to reinforce gypsum boards. Increasing the state of knowledge regarding the possibility of replacing synthetic fibers with natural fibers is another step towards creating more environmentally friendly building materials and determining their characteristics. This paper investigates the possibility of manufacturing fiber-gypsum composites based on natural gypsum (building gypsum) and hemp (Cannabis sativa L.) fibers grown in Poland. The effect of introducing hemp fibers of different lengths and with varying proportions of mass (mass of gypsum to mass of fibers) into the gypsum matrix was investigated. The experimental data obtained indicate that adding hemp fibers to the gypsum matrix increases the static bending strength of the composites manufactured. The highest mechanical strength, at 4.19 N/mm2, was observed in fiber-gypsum composites with 4% hemp fiber content at 50 mm in length. A similar trend of increased strength was observed in longitudinal tension. Again, the composite variant with 4% fiber content within the gypsum matrix had the highest mechanical strength. Manufacturing fibers-gypsum composites with more than 4% hemp fiber content negatively affected the composites' strength. Mixing long (50 mm) hemp fibers with the gypsum matrix is technologically problematic, but tests have shown a positive effect on the mechanical properties of the refined composites. The article indicates the length and quantity limitations of hemp fibers on the basis of which fiber-gypsum composites were produced.

Influence of accelerated aging on mechanical properties and aging behavior of glass fiber reinforced pipe

In this work, the accelerated aging test of GFRP in two thermal environments was conducted. The accelerated aging test was conducted at a constant temperature of 95°C for periods of 3000h to analyze and study the aging behaviors and mechanism under two environments. Resin defects caused by aging were found in the SEM images, and degradation of the fiber/resin interface was observed. Both the hoop tensile test and uniaxial compression test showed brittle fracture characteristics, and the strength of hydrothermal aging specimens decreased more significantly. Due to matrix degradation, uniaxial compression fracture after hydrothermal aging was observed that the resin exhibited poor adhesion. The decrease in the hardness of the outer resin layer was attributed to the development of the degree of molecular chain breakage. ATR-FTIR results showed that the accelerated aging process is accompanied by changes in the concentration of functional groups. The change in C-H intensity was attributed to the post-curing phenomenon. Accelerated aging resulted in the formation of carboxylic acids or esters and the introduction of hydroxyl groups. Thermogravimetric tests showed that accelerated aging did not change the thermal decomposition temperature of epoxy resins, but caused a decrease in resin content.

Damage monitoring of glass/epoxy-curved laminates with different stacking sequences using acoustic emission

Delamination is a major concern in the curvature area of a composite laminate due to the flexural stresses occurring between the laminates. This research focuses on the respective merits of different stacking sequences obtained by layering the glass fiber reinforcement at various orientations in an epoxy resin to manufacture a curved laminate. In particular, laminates with stacking sequences, such as Unidirectional [0°]24, Cross-ply [0°/90°]6S, Angle ply [±45°]6S, and Quasi-isotropic laminates [0°/±45°/90°]3S, were tested by performing four-point bending tests. Acoustic emission (AE) monitoring and experimental analysis characterized damage modes, including delamination. AE parameters, such as amplitude, energy, duration, cumulative count, and peak frequency, were utilized to characterize the damage mechanisms of the various stacking sequences. Experimental AE data confirmed that fiber orientation influences delamination resistance and failure mechanisms. Furthermore, compared to other layup sequences, the peak load of cross-ply (Layup B) was found to be greater by 48.7%, 32.87%, and 50.14%. Cross-ply curved laminates also have higher interlaminar tensile strength and curved beam strength than other sequences. They also failed less often due to delamination than other sequences. Finally, scanning electron microscope characterization verified and validated all damage processes found in the AE data collection. As a result, these findings play a significant role in predicting the lifetime, delamination failure, and strength of curved composite laminates.

Construction of Vine-Inspired Antimicrobial Filter with Multiscale 3D Nanonetwork for High-Efficiency Air Filtration.

Enhancing the antimicrobial activity of high-efficiency particulate air (HEPA) filters while maintaining filtration efficiency and pressure drop is currently an urgent issue for preventing the spread of pathogenic microorganisms. Herein, inspired by vines which can enwind fences to fix as well as decorate them, a flexible antimicrobial chitin nanofiber (ChNF@CuOx) was fabricated and loaded onto the rigid glass fiber (GF) skeleton of a HEPA filter. Through the physical interaction, ChNF@CuOx was spontaneously enwound on GF, and ChNF@CuOx itself interweaved to form a new nanonetwork between the GF skeleton. The obtained antimicrobial air filter (ChNF@CuOx/GF) with a unique nanonetwork increased the filtration efficiency of the HEPA filter. Meanwhile, it possessed excellent inactivation ability against Staphylococcus aureus, Escherichia coli, and Candida albicans due to the urchin-like in situ grown CuOx on the ChNF. In particular, the oxygen vacancies generated unexpectedly in CuOx enabled it to produce reactive oxygen species. After eight cycles of antimicrobial assays, the antimicrobial rates of bacteria were higher than 99.5%, and those of fungi were greater than 98.3%. The successful synthesis of antimicrobial fibers and the construction of multidimensional nanoscale structures through a simple postprocessing method provide a new design mentality for antimicrobial functionalization for HEPA filters.

Synergistic effects of sisal/glass fiber hybridization and eggshell powder filler on the performance of eco‐friendly polymer composites

AbstractIn recent years, there has been a significant emphasis on the development of composite materials that are both high‐performing and environmentally friendly. Hybrid polymer composites that are reinforced by both sisal and glass fibers are introduced in this study. Investigation was conducted to evaluate the combined influence of hybrid reinforcements and Egg Shell Powder (ESP) on the mechanical properties of the composites. The hand layup technique was employed to create hybrid laminates by incorporating variable amounts of ESP (0–15 wt%) and employing various stacking sequences. Various mechanical testing was administered to the composites that had been prepared. The results indicated that the glass/sisal hybrid laminates exhibited superior mechanical properties in comparison to the non‐hybrid sisal laminates, which was attributed to the synergistic benefits of incorporating both sisal and glass fibers. The incorporation of Egg Shell Powder significantly improved the material's mechanical properties. The glass/sisal hybrid laminates with 15% ESP laminate demonstrated the maximum tensile strength (195.23 MPa), flexural strength (150.02 MPa), and ILSS (7.55 MPa). Scanning electron microscopy enabled a comprehensive analysis of the hybrid composites' interfacial adhesion and microstructure. This investigation verified that the ESP was effectively dispersed and had a substantial effect on the interface between the matrix and the fibers. The hybrid composites that are generated are environmentally friendly and exhibit extraordinary potential for a variety of applications, offering a sustainable and high‐performing alternative to conventional synthetic composites. These discoveries promote the utilization of bio‐based resources in the composites industry and advance the development of sustainable materials.Highlights The glass/sisal hybrid laminates with 15% ESP laminate showed highest tensile strength of 195.23 MPa Hybrid composites exhibited superior mechanical properties. ESP addition significantly improved interfacial adhesion and strength Water absorption decreased with increasing ESP content up to 15% Development of Eco‐friendly composites suitable for automotive and aerospace applications

Impact of graphite on tribo‐mechanical, structural, and thermal behaviors of polyoxymethylene copolymer/glass fiber hybrid composites via Taguchi optimization

AbstractUnique hybrid thermoplastic composites based on polyoxymethylene copolymer (POM C), 10 wt.% glass fiber (GF) and graphite (Grt) filler at 1, 3, and 5 wt.% were developed using injection molding technique. According to the Taguchi L16 orthogonal array, present experiments were carried out with the aim of determining the coefficient of friction (COF) and specific wear rate (SWR) under a range of loads (namely, 5, 10, 20, and 30 N), sliding speeds (namely, 200, 400, 600, and 800 rpm), and run times (namely, 15, 30, 45, and 60 min) with varying wt.% of Grt (namely, 1, 3, and 5 wt.%) throughout the experiment. Analysis of variance (ANOVA) was used to evaluate the most significant factors that affect the output functions (viz., COF and SWR). The findings demonstrated that POM C/10GF composites' tribo‐mechanical, structural, and thermal properties were considerably improved upon by including Grt. Various microscopical methods were also employed to study the wear mechanisms of the composites and the surface morphology of the worn samples. The POM C/10GF with a 3 wt.% of Grt exhibited superior tribological properties owing to its enhanced interfacial bonding characteristics, resulting to increased wear resistance.Highlights Injection molded POM C/10GF hybrid composites with 1, 3, and 5 wt.% graphite (Grt) Structural, thermal, chemical, tribo‐mechanical and microstructural studies Design of experiment with variable loads, times, speeds, and Grt compositions COF and specific wear resistance as response Optimization of hybrid composite composition using Taguchi L16 orthogonal array