Glass Fiber Resin Research Articles

Comparison of Experimental and Numerical Investigation of Mono-Composite and Metal Leaf Spring

The automotive industry is increasingly focused on reducing vehicle weight, leading to the widespread adoption of composite materials with high strength-to-weight ratios in both aviation and automotive sectors. These materials are gradually replacing traditional options like steel. Leaf springs, one of the oldest and most common suspension components, continue to be widely used in vehicles. This study aims to replace conventional multi-leaf steel springs with mono-composite leaf springs while preserving the same load-carrying capacity and stiffness. Composite materials, such as glass fiber and epoxy resin, provide advantages including higher elastic strain energy storage, superior strength-to-weight ratios, and enhanced corrosion resistance compared to steel. Consequently, the weight of leaf springs can be reduced without sacrificing performance. The steel and mono-composite leaf springs were modeled using Catia software, and their performance was evaluated using ANSYS 15.0 software.

Rehabilitation and reinforcement of cracked pavements using crack sealers and composite patches

Cracking is a significant concern for pavements and should be appropriately treated during road, highway, and runway rehabilitation. This study investigates the behavior of asphaltic materials under tensile and shear loading modes in intact, fractured, and repaired conditions. With this aim, several methods and materials are utilized for repairs, such as poring adhesive into the crack (using bitumen, neat epoxy resin, and polymer concrete adhesives) and patching the crack with textile (by glass fiber and epoxy resin or bitumen). These tests were conducted at +10 °C, with a three-point bending loading configuration, the same as the actual loading configuration of pavements. Criteria such as failure load, failure work, and post-failure work, as well as failure patterns, were assessed to assess the effectiveness of repairs. Numerical analysis was also performed, and a constitutive model was presented. The ultimate tensile capacity of the cracked specimen is measured at 63 % lower than the intact condition (778 N). The ultimate tensile load of the bitumen-repaired specimen is higher than that of the cracked specimen, but it is still 11 % lower than that of the intact condition. The ultimate tensile capacity of epoxy resin repaired and polymer concrete repaired specimens are 88 % and 79 % higher than the intact specimen (about 1400 N). The ultimate tensile load of the fabric patch reinforced specimen that used bitumen as the adhesive is 38 % higher than the intact specimen (1075 N), while for the case of using the epoxy resin adhesive, this value is 258 % (2788 N). Observations of tensile failure patterns show that, because bitumen is viscoelastic, failure in bitumen-repaired specimens happens in bitumen necking mode and starts at the repaired crack tip. In other cases, the failure occurred far from the pre-crack plane.

Enhancing wear resistance, mechanical properties of composite materials through sisal and glass fiber reinforcement with epoxy resin and graphite filler

This study investigates the mechanical and wears properties of sisal and glass fiber-reinforced epoxy composites with graphite as filler material. We assessed the mechanical properties of the hand-layup-fabricated composite materials, including hardness, tensile strength, flexural strength, and impact strength, by ASTM standards. We also performed wear evaluations using a pin-on-disc apparatus. The results showed that the weight fractions of sisal fiber, glass fiber, graphite, and epoxy resin significantly affected the mechanical properties of the composites. In contrast to composites reinforced with individual fibers, hybrid composites exhibited enhanced mechanical properties. The optimized compositions showed improvements in tensile, flexural, impact, and hardness properties. The wear analysis revealed that a variety of factors, including the weight percentage of reinforcement, sliding velocity, load, and sliding distance, had an impact on the composites' wear resistance. The SEM images provided significant insights into the composite material's micro structural characteristics and failure mechanisms. In general, this research showcases the potential of graphite filler-reinforced sisal and glass fiber epoxy composites for use in applications that demand exceptional abrasion resistance and mechanical strength. Further refinement of the composition and processing methodologies could lead to the development of composites tailored to specific application demands.

Effect of Surface Treatment and BN Content on the Mechanical Properties of Aluminum Laminates Reinforced with Glass Fiber and Epoxy Resin

Effect of Surface Treatment and BN Content on the Mechanical Properties of Aluminum Laminates Reinforced with Glass Fiber and Epoxy Resin

Elastic Property Evaluation of Fiberglass and Epoxy Resin Composite Material Using Digital Image Correlation.

This study focused on evaluating the sensitivity and limitations of the simplified equipment used in the Digital Image Correlation (DIC) technique, comparing them with the analog extensometer, based on the mechanical property data of a composite made of fiberglass and epoxy resin. The objectives included establishing a methodology based on the literature, fabricating samples through manual lamination, conducting mechanical tests according to the ASTM D3039 and D3518 standards, comparing DIC with the analog extensometer of the testing machine, and contrasting the experimental results with classical laminate theory. Three composite plates with specific stacking sequences ([0]3, [90]4, and [±45]3) were fabricated, and samples were extracted for testing to determine tensile strength, modulus of elasticity, and other properties. DIC was used to capture deformation fields during testing. Comparisons between data obtained from the analog extensometer and DIC revealed differences of 11.1% for the longitudinal modulus of elasticity E1 and 5.6% for E2. Under low deformation conditions, DIC showed lower efficiency due to equipment limitations. Finally, a theoretical analysis based on classical laminate theory, conducted using a Python script, estimated the longitudinal modulus of elasticity Ex and the shear strength of the [±45]3 laminate, highlighting a relative difference of 31.2% between the theoretical value of 7136 MPa and the experimental value of 5208 MPa for Ex.

Contemporary Concepts of Adhesive Cementation of Glass-Fiber Posts: A Narrative Review.

(1) Background: Cementation of glass fiber posts to root canals has been associated with various failures, especially debonding. This narrative review aims to present the contemporary concepts concerning the adhesive cementation of glass fiber post and to discuss the optimal management of these factors. (2) Methods: Electronic search was performed in MEDLINE/Pub Med and Google Scholar using selected keywords examining the parameters post length, surface treatment of glass fiber posts, post space preparation and dentin pretreatment, resin cement selection, adhesive systems and hybrid layer formation, and clinical techniques. (3) Results: The search led to the selection of 44 articles. Epoxy resin-based endodontic sealers are recommended and the use of temporary cement in the root canal should be avoided. The minimum length of a glass fiber post adhesively cemented to a root canal is 5 mm. Irrigating the root canals with chlorhexidine, MTAD, or EDTA (alone or in combination with NaOCl) after post space preparation seems to enhance the bond strength. Silane application on the surface of the post seems to be beneficial. Concerning resin cements and adhesive systems, the results were rather inconclusive. Finally, resin cement should be applied inside the root canal with an elongation tip and photoactivation should be delayed. (4) Conclusions: Contemporary concepts of adhesive cementation of glass fiber posts can indeed improve the bond between glass fiber posts, resin cement, and root canal dentin, however, evidence coming from long-term randomized prospective clinical trials is needed in order to obtain safer conclusions.

Electro-Mechanical Coupling Analysis of L-Shaped Three-Dimensional Braided Piezoelectric Composites Vibration Energy Harvester.

In this article, an L-shaped three-dimensional (3D) braided piezoelectric composite energy harvester (BPCEH) is established, which consists of an elastic layer composed of a 3D braided composite, flanked by upper and lower layers of piezoelectric material and two tuning mass blocks. Glass fiber and epoxy resin are used to produce a 3D braided composite. This L-shaped 3D BPCEH is mechanically designable and can be adapted to different work requirements by varying the braided angle of the 3D braided composite layer. The material parameters of 3D braided composites are predicted for different braided angles by means of a representative volume element (RVE). Electro-mechanical coupled vibration equations for the L-shaped 3D BPCEH are established. The impact of braided angles on voltage and power output is discussed in this article. Simulations using finite element method are conducted to analyze the voltage and power output responses at various braided angles. In addition, the effects of the mass of mass block B and the length of the beam on the output performance of the L-shaped 3D BPCEH are analyzed.

A pool construction using ramie fabric composite in eco-resin matrix: a cost of goods sold analysis (COGS)

One of the oldest and most traditional products made with resin and fiberglass is swimming pools; however, this product consumes large quantities of fiberglass mat and resin, both raw materials are based on non-renewable products and contribute significantly to carbon footprint and environmental damage. The increasing environmental concern has raised awareness in the industry and academia for the search of environmentally friendly materials. Natural fibers are attracting interest in engineering sectors due to specific advantages such as low density and cost, as well as renewability, biodegradability, recycling, and CO2 emission neutrality. In particular, the fiber extracted from the stem of the ramie plant is currently recognized as one of the strongest lignocellulosic fibers. In addition to natural fibers, eco-resins such as water-based acrylics have gained great attention from the industry due to their carbon footprint and environmentally friendly characteristics. The aim of this work is to calculate the cost of goods sold (COGS) for a pool constructed with composite ramie fabric in a water-based eco-resin matrix, for this purpose, a 1:30 scale prototype will be made, from which all manufacturing costs will be collected, then we will perform a mathematical extrapolation for comparison of values with products currently available in the market.

Experimental Investigation and Analysis of Mechanical Properties of Chopped Strand Mat-E Glass Fiber Polyster Resin & Silica Powder Composites

Composite materials play a vital role in many industrial applications. Researchers are working on fabrication of new composite materials worldwide to enhance the applicability of these materials. In view of this the mechanical performance of the composite material is essential. The objective of the present work is to analyze the effect of Silica powders content on the mechanical behavior of woolen E-glass 350gm-Glass fiber reinforced. Five different types of composites are fabricated using 0%,2%,4%,6%,8%wt of Silica powders with woolen-E glass fiber and polyester resin. The polyester resin, catalyst and accelerator are mixed in 50:1:1weight ratio in polyester matrix Silica. The aim of the project is to investigate the effect of Silica powders with woolen e-glass 350gm for making the composite material stronger and tougher. The investigation is carried out by mixing different weight percentages of the Silica powders with the polyester resin and preparing individual samples. After woolen- eglass preparation, the materials were properly mixed using the hand-lay techniques and different specimens were prepared with different compositions of the Silica powders. After all the samples were prepared, mechanical tests were carried out on the samples to ascertain the changesobserved due to the composition of Silica powders. The obtained results of various samples specimens were compared and graphically charted to characterize the new composites material. Keywords: Chopped Strand Mat (CSM) 450 G M-Glass Fiber; Silica Powder; Polyester Resin;Hand-Lay;Catalyst;Accelerator.

Microwave Anaerobic Thermal Removal of Bromine from Copper-Containing Glass Fiber Resin

Microwave Anaerobic Thermal Removal of Bromine from Copper-Containing Glass Fiber Resin

Experimental Investigation and Analysis of Mechanical Properties of Chopped Strand Mat-E Glass Fiber Polyster Resin & Graphite Powder Composites

Composite materials play a vital role in many industrial applications. Researchers are working on fabrication of new composite materials worldwide to enhance the applicability of these materials. In view of this the mechanical performance of the composite material is essential. The objective of the present work is to analyze the effect of graphite powders content on the mechanical behavior of woolen E-glass 350gm-Glass fiber reinforced. Five different types of composites are fabricated using 0%,2%,4%,6%,8%wt of graphite powders with woolen-E glass fiber and polyester resin. The polyester resin, catalyst and accelerator are mixed in 50:1:1weight ratio in polyester matrix graphite. The aim of the project is to investigate the effect of graphite powders with woolen e-glass 350gm for making the composite material stronger and tougher. The investigation is carried out by mixing different weight percentages of the graphite powders with the polyester resin and preparing individual samples. After woolen- eglass preparation, the materials were properly mixed using the hand-lay techniques and different specimens were prepared with different compositions of the graphite powders. After all the samples were prepared, mechanical tests were carried out on the samples to ascertain the changesobserved due to the composition of graphite powders. The obtained results of various samples specimens were compared and graphically charted to characterize the new composites material. Keywords: MattE-Glass 350gm; Polyester resin; Graphite powders; Hand- Lay technique ; Catalyst & Accelerator.

MANUFAKTUR UAV FIXED WING MENGGUNAKAN MATERIAL STYROFOAM DENGAN METODE LAY-UP (PELAPISAN) FIBERGLASS DAN RESIN

This research discusses the development of a manufacturing process for a fixed wing-based UAV (Unmanned Aerial Vehicle) using Styrofoam material as the structural core. The manufacturing method applied is lay-up of fiberglass and resin to improve the strength and aerodynamic performance of the UAV. This research aims to evaluate the potential of styrofoam material enhanced by such lay-up technique. The research method involves the steps of applying fiberglass and resin lay-up on Styrofoam structure. The results of the Fixed Wing UAV Manufacturing research using Styrofoam material with fiberglass resin lay-up method, the aircraft structure becomes lighter and stronger with the overall resulting load reaching 2750 Gram or 2.75 kg. The results showed that the application of the lay-up method significantly improved the structural strength of the UAV, while the use of fiberglass and resin materials made a positive contribution to its aerodynamic performance. The invention has the potential to improve the efficiency and durability of UAVs in monitoring and surveillance applications. By presenting alternative materials and manufacturing methods, this research can contribute to the development of more reliable and effective UAV.

Comparative analysis of stress distribution in residual roots with different canal morphologies: evaluating CAD/CAM glass fiber and other post-core materials

BackgroundThe selection of post-core material holds significant importance in endodontically treated teeth, influencing stress distribution in the dental structure after restoration. The use of computer-aided design/computer-aided manufacturing (CAD/CAM) glass fiber post-core possesses a better adaptation for different root canal morphologies, but whether this results in a more favorable stress distribution has not been clearly established.Materials and methodsThis study employed finite element analysis to establish three models of post-core crown restoration with normal, oversized, and dumbbell-shaped root canals. The three models were restored using three different materials: CAD/CAM glass fiber post-core (CGF), prefabricated glass fiber post and resin core (PGF), and cobalt-chromium integrated metal post-core (Co-Cr), followed by zirconia crown restoration. A static load was applied and the maximum equivalent von Mises stress, maximum principal stress, stress distribution plots, and the peak of maximum displacement were calculated for dentin, post-core, crown, and the cement acting as the interface between the post-core and the dentin.ResultsIn dentin of three different root canal morphology, it was observed that PGF exhibited the lowest von Mises stresses, while Co-Cr exhibited the highest ones under a static load. CGF showed similar stress distribution to that of Co-Cr, but the stresses were more homogeneous and concentrated apically. In oversized and dumbbell-shaped root canal remnants, the equivalent von Mises stress in the cement layer using CGF was significantly lower than that of PGF.ConclusionsIn oversized root canals and dumbbell-shaped root canals, CGF has shown good performance for restoration of endodontically treated teeth.Clinical relevanceThis study provides a theoretical basis for clinicians to select post-core materials for residual roots with different root canal morphologies and should help to reduce the occurrence of complications such as root fracture and post-core debonding.

Daya Tahan Coldmix Asphalt Sebagai Bahan Darurat Penanganan Jalan dengan Bahan Resin Fiberglass Sebagai Pengganti Aspal

Asphalt is a material that is widely used in road construction. The use of asphalt materials is getting higher, but the asphalt materials used are increasingly expensive and limited, research was conducted with Coldmix Ashpalt with the addition of fiberglass resin with the aim of determining the effect of adding fiberglass resin to AC-WC asphalt materials. The method used for research is carried out in the laboratory with the marshall test method then obtained the calculation results, namely the marshall quotient. The characteristics of AC-WC pavement mixtures include density, cavities in aggregate minerals (VMA), asphalt filled cavities (VFA), voids in the mixture (VIM), stability, marshall melt (flow), and Marshall Quotient (MQ). The results of the study of 4 variations of the deep fiberglass resin mixture used with variation values of 0%, 2%, 3%, 4%. for the variation value that has the highest stability is found in the 3% variation with a stability value of 1577.33 kg, with a VMA value of 15.50%, VFA value of 87.18%, VIM value of 3.28%, flow value of 3.13 mm, and MQ value of 510.72 kg / mm. The variation content of 3% is declared the most effective for mixing AC-WC asphalt because the values of the marshall properties meet the 2018 Highways engineering specifications, so that the most optimal variation of fiberglass resin added material is used as a mixture of AC-WC asphalt with a penetration of 60/70.

Tree-based machine learning approach to modelling tensile strength retention of Fibre Reinforced Polymer composites exposed to elevated temperatures

Fibre Reinforced Polymer (FRP) composites are susceptible to degradation at elevated temperatures. Accurate modelling of the tensile performance of FRP composites under high-temperature exposure is crucial for their structural integrity. In this study, tree-based models, namely, decision tree, M5P, and random forest methods, are utilised to model the impact of elevated temperatures on the tensile strength of composite materials. A database of 787 experimental results is established and processed to train and test the regression tree models. The exposure temperature, resin glass transition temperature, sample thickness/diameter, exposure duration, ambient cooling, fibre-to-resin ratio, fibre orientation, resin type, fibre type, and manufacturing process were considered as the main parameters affecting the tensile strength retention (TSR) of FRP composites after exposure to elevated temperatures. To improve the prediction performance of machine learning, Bayesian optimisation and 10-fold cross validation (CV) technique were used to train regression tree methods. The results demonstrated the accuracy of the developed models in predicting the TSR of the composites under elevated temperatures. Feature contribution analysis showed that the exposure temperature exerts the most significant impact on the TSR, with the glass transition temperature coming next in importance. These were followed by sample thickness, exposure duration, ambient cooling, fibre-to-resin ratio, and fibre orientation, respectively. Resin type, fibre type, and the manufacturing process had the least contributions to the observed variations in TSR. Examining the tensile strength retention of FRP composites at high temperatures enables the development of precise predictive models and design guidelines for their optimal use across industries.

Analysis of the mechanical properties of the single layered braid reinforced thermoplastic pipe (BRTP) for oil & gas industries

Reinforced thermoplastic pipes (RTPs) are instantly being broadly scrutinized as a feasible surrogate for metallic pipes due to their superior corrosion resistance, low weight, and low maintenance worth, they have three primary layers inner, outer, and reinforcement. Process parameters for manufacturing reinforced layers are critically essential to enhancing the mechanical performance of RTPs. However, limited comparative research on the impact of braiding parameters on RTP’s mechanical characteristics appears to be publicly available. Therefore, this study examines how these variables affect the mechanical characteristics of braid RTP. This new class of braid RTP is constructed of an HDPE liner pipe, over-wrapped with a single braid layer of resin glass fiber. L9 Taguchi orthogonal array design for experiments was used to create specimens. Furthermore, specimens were subjected to tensile and compression to assess their mechanical properties. Epoxy and ±75 were the most promising parameters in achieving the highest number of tensile and compression properties among choices of thermoplastic polymer matrices and braid angles, respectively. ANOVA suggested that both parameters are significant and significantly impact the mechanical properties of the prototype braid RTP. Also, A1B3 is considered the best combination for producing braid RTP with higher mechanical performance; no notable interaction among factors was found.

Effect of red mud on mechanical and thermal properties of agave sisalana/glass fiber–reinforced hybrid composites

Abstract The mechanical, thermal, and morphological analysis of red mud filled sisal/glass fiber–reinforced polyester composites have been investigated. In this study, four composite specimens were prepared through hand layup technique by changing the weight percentage of sisal fiber and red mud. Weight percentage of glass fiber and polyester resin are kept constant. The fabricated composite specimens were subjected to mechanical properties such as hardness, impact and tensile behavior, thermal, and morphological analysis. From the results, it is observed that, maximum tensile strength of 45.6 MPa was obtained for C1 specimen. Maximum hardness and impact strength of 85.67 and 391.5 J m−1 was achieved for C2 specimen. In TGA study, C1 and C2 specimen exhibited 85 % of weight loss with the temperature ranges from 300 °C to 400 °C. From SEM analysis, good bonding between fiber and matrix, voids, fiber breakages, fiber pullout, delamination, rich matrix area, poor adhesion between fiber and matrix, poor arrangement of fibers, interlinked fibers, and crack propagation were observed. Based on the results, C2 specimen which contains 30 wt% of sisal fiber and 5 wt% of red mud is performed well than other composites and it is suitable for various applications such as marine, automobile, and aeronautical.

Restoration of a Vital Tooth With Extensive Crown Destruction Using Glass Fiber and Polyethylene Fiber-reinforced Composite Resin: A Clinical Case.

Conservative restorative dentistry has been evolving in the last 25 years, focusing mainly on the development of direct restorative materials. Resin-based composites remain an excellent conservative alternative for restoration of teeth with extensive caries lesions. Over time, several strategies have been proposed to improve the mechanical properties of these composites so that they can adequately withstand masticatory forces. Glass fiber-reinforced resin-based composites and their use in situations where there is great loss of tooth structure have gained popularity due to their favorable mechanical properties. Combined techniques with polyethylene fibers can further enhance their clinical performance. This study presents a brief review of their most important qualities and potential use in direct restorative procedures. In addition, a clinical case is described where a vital tooth with extensive coronal destruction was restored using polyethylene fibers embedded in glass fiber-reinforced flowable resin under resin-based composite. The reinforcement of both the remaining tooth structure and the restoration with fibers is a valid treatment option since the network structure formed by the fiber reinforcement can increase the longevity of the direct composite restorations. There are few reports in the literature describing the use of a combined technique using polyethylene fibers embedded in glass fiber-reinforced flowable resin under resin-based composite. Thus, clinical follow-up of this case is required.

Comparative evaluation of fracture resistance of endodontically treated teeth restored with and without horizontal posts, using packable and bulkfill flowable composite: An in vitro study

Introduction: Root canal therapy is often required due to the pulpal and periradicular infection after coronal hard tissue loss. A high risk of biomechanical failure is associated with loss of structural integrity with endodontically treated teeth. Prognosis is affected by various parameters, such as extent of tooth structure loss, ferrule height, post and cores, and materials used for restoration. Aim: The aim of this study was to comparatively evaluate the fracture resistance of endodontically treated teeth with mesio-occluso-distal (MOD) cavities restored with horizontal glass fiber resin posts and composite. Materials and Methods: Ninety intact extracted maxillary molars were collected, subjected to endodontic treatment, and were divided into 6 groups (n = 15): Group 1 (control group, untreated teeth), Group 2 (cavity without restoration), Group 3a (cavity restored with Neo Spectra ST), Group 3b (cavity restored with Neo Spectra ST after placement of horizontal glass fiber resin posts), Group 4a (cavity restored with SDR Plus), and Group 4b (cavity restored with SDR Plus after placement of horizontal fiber resin posts). Then samples were subjected to a universal testing machine for evaluation. Data were statistically analyzed. Results: The mean (standard deviation) fracture load among groups was 354.46 N (±31.15N) to 1241.73 N (±29.97N). Significant statistical difference at P < 0.05 was present between the groups, Group 1>Group 4b>Group 3b>Group 4a>Group 3a>Group 2. Conclusion: Under the limitations of this in vitro study, it can be concluded that samples of MOD cavities in endodontically treated teeth, when incorporated with horizontal glass fiber resin posts, resulted in higher fracture resistance.

Poster 237: Menisco-Tibial Ligament Complex Anatomy and Biomechanics – Implications for Meniscus Repairs, Ramp Lesions and Transplants

Poster 237: Menisco-Tibial Ligament Complex Anatomy and Biomechanics – Implications for Meniscus Repairs, Ramp Lesions and Transplants