GHz Bursts Research Articles

Efficient Ablation, further GHz Burst Polishing, and Surface Texturing by Ultrafast Laser

Efficient Ablation, further GHz Burst Polishing, and Surface Texturing by Ultrafast Laser

Damping of Strong GHz Waves near Magnetars and the Origin of Fast Radio Bursts

We investigate how a fast radio burst (FRB) emitted near a magnetar would propagate through its surrounding dipole magnetosphere at radii r = 107–109 cm. First, we show that a GHz burst emitted in the O-mode with luminosity L ≫ 1040 erg s−1 is immediately damped for all propagation directions except a narrow cone along the magnetic axis. Then, we examine bursts in the X-mode. GHz waves propagating near the magnetic equator behave as magnetohydrodynamic (MHD) waves if they have L ≫ 1040 erg s−1. The waves develop plasma shocks in each oscillation and dissipate at r∼3×108L42−1/4 cm. Waves with lower L or propagation directions closer to the magnetic axis do not obey MHD. Instead, they interact with individual particles and require a kinetic description. The kinetic interaction quickly accelerates particles to Lorentz factors 104–105 at the expense of the wave energy, which again results in strong damping of the wave. In either propagation regime, MHD or kinetic, the dipole magnetosphere surrounding the FRB source acts as a pillow absorbing the radio burst and reradiating the absorbed energy in X-rays. These results constrain the origin of observed FRBs. We argue that the observed FRBs avoid damping because they are emitted by relativistic outflows from magnetospheric explosions, so that the GHz waves do not need to propagate through the outer equilibrium magnetosphere surrounding the magnetar.

Electron Cyclotron Maser Emission and the Brightest Solar Radio Bursts

This paper investigates the incidence of coherent emission in solar radio bursts, using a revised catalog of 3800 solar radio bursts observed by the Nobeyama Radio Polarimeters from 1988 to 2023. We focus on the 1.0 and 2.0 GHz data, where radio fluxes of order 1010 Jy have been observed. Previous work has suggested that these bursts are due to electron cyclotron maser (ECM) emission. In at least one well-studied case, the bright emission at 1 GHz consists of narrowband spikes of millisecond duration. Coherent emission at 1 GHz can be distinguished from traditional incoherent gyrosynchrotron flare emission based on the radio spectrum: Gyrosynchrotron emission at 1 GHz usually has a spectrum rising with frequency, so bursts in which 1 GHz is stronger than higher-frequency measurements are unlikely to be incoherent gyrosynchrotron. Based on this criterion, it is found that for bursts exceeding 100 sfu, three-quarters of all bursts at 1 GHz and half of all 2 GHz bursts have a dominant coherent emission component, assumed to be ECM. The majority of the very bright bursts at 1 GHz are highly circularly polarized, consistent with a coherent emission mechanism, but not always 100% polarized. The frequency range from 1 to 2 GHz is heavily utilized for terrestrial applications, and these results are relevant for understanding the extreme flux levels that may impact such applications. Further, they provide a reference for comparison with the study of ECM emission from other stars and potentially exoplanets.

88‐1: Distinguished Paper: Direct Laser Patterning of Glass Mask for Micro Display Using GHz Bursts

Development of high‐precision RGB patterning process is needed to implement high‐resolution micro display (OLEDoS) for next‐generation VR/AR products. In general, specially designed and manufactured masks are required to realize above 3,000ppi high‐resolution display in structured OLED material deposition. In this study, we implemented direct laser patterning IR‐fs optical system operating in MHz and GHz burst modes and evaluated its capability for precise micro‐drilling of alumino‐borosilicate glass materials. The fine hole‐shaped pattern is produced at a minimum of 5µm pitch level for about 0.6 inch area without sacrificing the glass strength. It is expected to contribute to the high precise manufacture of ultra fine mask (UFM) using thin glass platform corresponding to micro displays in the future.

Efficient Ablation, further GHz Burst Polishing, and Surface Texturing by Ultrafast Laser

A large variety of ultrafast laser‐matter interaction regimes and different processed surface finishing qualities of stainless steel can be achieved by varying the laser processing parameters. The optimization of the laser fluence to the most efficient ablation also leads to the lowest surface roughness of the ablated material. High laser fluence together with a high pulse repetition rate leads to heat accumulation, which results in the formation of microstructures with various morphology and scales. The use of GHz bursts allows a rough stainless‐steel surface to be smoothed and even polished. In this work, the fast and high‐quality milling of 2.5D cavities is demonstrated. Laser beam spot optimization is used to increase the throughput of the high‐power femtosecond laser (67.8 W), resulting in an ablation rate of 13 mm3 min−1. The complex cavities are produced by laser milling and cutting in layers. The formation of surface structures on stainless steel because of laser irradiation has been demonstrated. The possibilities of further GHz burst polishing are examined on previously laser‐milled stainless steel using with lowest possible surface roughness. The ability to polish the surface with microstructures below the original roughness is demonstrated by bursts of ultrashort pulses with a repetition rate in the GHz range. It has been demonstrated that mold milling in stainless steel designed for LED diffusers can be fabricated using a modern femtosecond laser source together with beam size optimization technique for efficient ablation with low surface roughness, layer‐by‐layer milling techniques, and GHz burst polishing techniques.

Direct laser patterning of glass mask for micro display using GHz bursts

AbstractDevelopment of high‐precision RGB patterning process is needed to implement high‐resolution micro display (OLEDoS) for next‐generation VR/AR products. In general, specially designed and manufactured masks are required to realize above 3000‐ppi high‐resolution display in structured OLED material deposition. In this study, we developed direct laser patterning IR‐fs optical system operating in MHz and GHz burst modes and evaluated its capability for precise micro‐drilling of aluminoborosilicate glass materials. The fine hole‐shaped pattern is produced at a minimum of 5 μm pitch level for about 0.6 in. area without sacrificing the glass strength. It is expected to contribute to the high precise manufacture of ultra fine mask (UFM) using thin glass platform corresponding to micro displays in the future.

Comparison of ablation rate on stainless steel using pulsed lasers in different burst modes

In this study, the ablation efficiency of single ultra-short laser pulses having different burst modes was evaluated on three types of stainless steel (AISI 420, AISI 304, and AISI 316Ti). The experiments are performed using an infrared ultra-short pulsed laser (1032 nm, 250 fs). The investigation focused on analyzing the morphology of the ablated craters to elucidate the influence of burst mode on surface quality. Additionally, the ablated volume is quantified to assess the achievable removal rate. The results indicate that the burst mode significantly affects both surface morphology of the ablated areas and the ablation volume. Moreover, the temporal pulse-to-pulse distance tp at GHz burst with tp = 450 ps and MHz burst with tp = 17 ns revealed a notable influence. By using MHz burst mode, the ablation volume for a single pulse was almost doubled compared to a pulse without burst, using the same pulse energy (from ∼ 100 µm3 to ∼ 200 µm3 depending on the steel alloy). Interestingly, by using GHz burst and bi burst the effective ablation volume drops significantly.

Characterization of batteries materials ablation by femtosecond pulses

The implementation of femtosecond laser processing in batteries fabrication is of high interest for automotive industry. The laser ablation mechanisms of composite materials used for batteries is a key knowledge for the laser processing optimization. In this work, we provide new results on fs ablation efficiencies for materials used in lithium-ion batteries. A very high value is obtained for specific ablation rates of graphite, up to 12 mm3/min/W, while the value is next to 0.2 mm3/min/W for the metallic substrate. The results show less benefit for MHz and GHz bursts of pulses in the case of graphite. Nevertheless because of the huge ablation efficiency difference between the active material and the metallic substrate, electrode cutting time is dominated by the metallic substrate cutting for which a significant benefit of GHz bursts is evidenced.

A fully integrated nanosecond burst RF generator for quantum technologies

AbstractQuantum technologies is an emerging field of physics and engineering based on exploiting properties of quantum mechanics such as entanglement, superposition, or tunneling, and which is expected to impact many applications, such as communications, simulation, computation, or sensing and metrology. The operation of quantum technologies is based on the manipulation of the quantum states of certain devices, either to induce transitions between states or to detect the transitions. Irrespective of the practical realization of these quantum devices, their manipulation requires interacting with their quantum resonant states, for which very narrow radio‐frequency (RF) bursts in the range of the GHz are required. Arbitrary waveform generators are used to generate these signals for test purposes, but this is not suitable for practical quantum technology applications, which will need to produce the required bursts by specific circuit building blocks with low power and small dimensions. Here, an integrated RF burst generator capable of producing GHz bursts shorter than 1 ns is presented. The proposed architecture is tested using a 5 GHz quadrature LC‐tank voltage‐controlled oscillator (LC‐VCO), showing that the four equally spaced phases can be switched every 500 ps, which allows the generation of more complex RF bursts for optimized quantum state manipulation.

High performance micromachining of sapphire by laser induced plasma assisted ablation (LIPAA) using GHz burst mode femtosecond pulses

High performance micromachining of sapphire by laser induced plasma assisted ablation (LIPAA) using GHz burst mode femtosecond pulses

Spectrum shuttle for producing spatially shapable GHz burst pulses

Spectrum shuttle for producing spatially shapable GHz burst pulses

1200-W all polarization-maintaining fiber GHz-femtosecond-pulse laser with good beam quality

In this work, we demonstrate a 1200-W average power all polarization-maintaining (PM) fiber ultrafast laser system operating at 1.0 µm. In accordance with the numerical modeling, the PM fiber laser system is designed and it delivers linearly-polarized femtosecond pulses at a 1.39-GHz fundamental repetition rate, with a maximum output power of 1214 W — to the best of our knowledge, the highest average power from all PM fiber ultrafast laser at 1.0 µm to date. The pulse width can be compressed to ∼800 fs with a beam quality of M2 < 1.1. This kilowatt-class all PM fiber laser system is expected to open new potential for high energy pulse generation through temporal coherent combination and laser ablation using GHz burst fs laser.

Formation of two-dimensional laser-induced periodic surface structures on titanium by GHz burst mode femtosecond laser pulses

GHz burst mode femtosecond (fs) laser pulses, which consist of a series of pulse trains with ultra-fast intervals of several hundred picoseconds, have offered distinct features for material processing compared to conventional irradiation of laser pulses (single-pulse mode). We apply GHz burst mode processing to fabricate laser-induced periodic surface structures (LIPSS) on the material surfaces. In our previous work for silicon (Si), we have found that GHz burst mode can create unique two-dimensional (2D) LIPSS composed of both parallel and perpendicular to the laser polarization direction. We proposed that the formation of 2D-LIPSS is attributed to the synergetic contributions of electromagnetic and hydrodynamic mechanisms. To further investigate more detailed formation mechanisms and explore practical applications, we employ titanium (Ti), whose properties are significantly different from Si. We demonstrate that GHz burst mode fs laser pulses (central wavelength: 1,030 nm, intra-pulse width: 230 fs, intra-pulse repetition rate (an intra-pulse interval): 4.88 GHz (205 ps) and burst pulse repetition rate: 10 kHz) can also fabricate 2D-LIPSS on Ti surfaces. We attribute the dominant formation mechanism of 2D-LIPSS to the generation of hot spots with highly enhanced electric fields due to transient change of material properties during GHz burst pulse irradiation. Based on this speculation, properly tailoring the shapes of the burst pulse with an optimum intra-pulse number enables the creation of well-defined 2D-LIPSS. Furthermore, essentially homogeneous 2D-LIPSS can be formed in a large area by laser scanning of a focused fs laser beam with a stage scanning speed of 5 mm/s.

Laser processing of silicon with GHz burst pumped third harmonics for precise microfabrication.

Femtosecond laser processing has proved to be a valuable tool for various microfabrication applications. In order to further increase the quality and efficiency of femtosecond laser processing, processing with GHz burst mode lasers has gained attention in recent years, where packets of high-repetition rate pulses are used instead of single pulses at the fundamental repetition rate. However, the use of burst-pulses has mainly been limited to the fundamental wavelength of powerful regenerative amplifier systems, often near 1 micrometer wavelength. In this study, we explore the characteristics and potential benefits of further wavelength conversion of burst-pulses emitted at the near-infrared to the ultraviolet region via direct third-harmonic generation. We construct an in-line process evaluation setup with a chromatic confocal sensor, and evaluate the ablation characteristics of the burst-pumped and non-burst processing of silicon. We observe that burst-mode processing has significantly reduced surface roughness and debris, resulting in high-quality laser processing. To demonstrate the utility of such burst-pumped UV processing, we show the successful milling of a spherical structure enabled by in-line surface profile feedback, while similar processing with non-burst conditions did not work. We believe such results show the strong potential of burst laser sources for use in accurate microfabrication of structures with micrometer-scale resolution.

Numerical Simulation of Silicon Laser Ablation with GHz Bursts of Femtosecond Pulses

Numerical Simulation of Silicon Laser Ablation with GHz Bursts of Femtosecond Pulses

Investigation of Ablation Efficiency of Stainless Steel Using Pulsed Lasers in Burst Mode

Due to its high corrosion resistance and mechanical properties, stainless steel is commonly used in various industrial applications. Although different types of stainless steel are similar in their chemical composition, they can differ significantly in their thermal diffusivity. This property is relevant in the ability of a material to conduct heat and thus, in laser processing. In this frame, this study compares the ablation efficiency and characteristics of polished stainless steel samples of the alloys AISI 304, AISI 420, and AISI 316Ti. They are irradiated with single ultrashort pulses having pulse durations between 250 fs and 10 ps as well as using GHz burst modii. The goal is to investigate the differences in both the ablation threshold and the ablation rate to improve the ablation efficiency. The results show that shorter pulse durations lead to a more efficient ablation process. On the other hand, GHz bursts are found to be, in general, less efficient. In addition, there is a significant difference in the surface morphology depending on the process parameters. The differences in the thermal diffusivity do not significantly influence the ablation threshold fluence but surface morphology and the ablation rate.

Study of GHz-Burst Femtosecond Laser Micro-Punching of 4H-SiC Wafers

The micromaching of silicon carbide using femtosecond laser pulses is becoming an important field of research. High-repetition-rate sub-pulse trains, so-called pulse bursts, are a particularly promising route towards completely new process regimes. We report on the results of micro-punching n-type 4H-silicon carbide wafers using GHz pulse burst in order to systematically investigate the influence of the temporal energy distribution on laser processing. Pulse-burst experiments are performed at a laser wavelength of λ= 1030 nm using a single GHz burst containing a varying number of pulses and then compared with standard single femtosecond pulse exposures. The pulse energy is swept across the ablation threshold. For each set of parameters, the micromachining efficiency is evaluated in terms of ablation efficiency and burr characteristics. Scanning electron micrographs provide qualitative information about the machining quality. The characteristics of the laser modification are discussed in relation to an increase in the number of pulses in a burst envelope and to an increase in pulse energy. We observe that, compared to a single pulse, a GHz burst comprised of 10 lower-energy pulses leads to an increase in the ablation rate by a factor of ≤ 10.

GHz bursts in MHz burst (BiBurst) enabling high-speed femtosecond laser ablation of silicon due to prevention of air ionization

For the practical use of femtosecond laser ablation, inputs of higher laser intensity are preferred to attain high-throughput material removal. However, the use of higher laser intensities for increasing ablation rates can have detrimental effects on ablation quality due to excess heat generation and air ionization. This paper employs ablation using BiBurst femtosecond laser pulses, which consist of multiple bursts (2 and 5 bursts) at a repetition rate of 64 MHz, each containing multiple intra-pulses (2–20 pulses) at an ultrafast repetition rate of 4.88 GHz, to overcome these conflicting conditions. Ablation of silicon substrates using the BiBurst mode with 5 burst pulses and 20 intra-pulses successfully prevents air breakdown at packet energies higher than the pulse energy inducing the air ionization by the conventional femtosecond laser pulse irradiation (single-pulse mode). As a result, ablation speed can be enhanced by a factor of 23 without deteriorating the ablation quality compared to that by the single-pulse mode ablation under the conditions where the air ionization is avoided.

Two-dimensional laser-induced periodic surface structures formed on crystalline silicon by GHz burst mode femtosecond laser pulses

Femtosecond laser pulses with GHz burst mode that consist of a series of trains of ultrashort laser pulses with a pulse interval of several hundred picoseconds offer distinct features in material processing that cannot be obtained by the conventional irradiation scheme of femtosecond laser pulses (single-pulse mode). However, most studies using the GHz burst mode femtosecond laser pulses focus on ablation of materials to achieve high-efficiency and high-quality material removal. In this study, we explore the ability of the GHz burst mode femtosecond laser processing to form laser-induced periodic surface structures (LIPSS) on silicon. It is well known that the direction of LIPSS formed by the single-pulse mode with linearly polarized laser pulses is typically perpendicular to the laser polarization direction. In contrast, we find that the GHz burst mode femtosecond laser (wavelength: 1030 nm, intra-pulse duration: 220 fs, intra-pulse interval time (intra-pulse repetition rate): 205 ps (4.88 GHz), burst pulse repetition rate: 200 kHz) creates unique two-dimensional (2D) LIPSS. We regard the formation mechanism of 2D LIPSS as the synergetic contribution of the electromagnetic mechanism and the hydrodynamic mechanism. Specifically, generation of hot spots with highly enhanced electric fields by the localized surface plasmon resonance of subsequent pulses in the bursts within the nanogrooves of one-dimensional LIPSS formed by the preceding pulses creates 2D LIPSS. Additionally, hydrodynamic instability including convection flow determines the final structure of 2D LIPSS.

Ultrafast laser ablation of copper with GHz bursts: A numerical study on the effects of repetition rate, pulse number and burst fluence on ablation efficiency and heat-affected zone

Ultrafast laser burst ablation (ULBA) with high repetition rates up to GHz has emerged as a promising method for improving ablation efficiency and reducing heat-affected zone (HAZ). However, the effects of different laser parameters are not well understood. This article presents a numerical study by an improved two-temperature model on the influences of repetition rate, pulse number and burst fluence on ablation efficiency and HAZ in ULBA of copper. Due to thermal accumulation, increasing the repetition rate enhances the maximum ablation efficiency, by over 150% at 3456 MHz. Interestingly, large pulse numbers also assist this effect by extending the period of thermal accumulation. However, if the burst fluence is too low, increased pulse numbers will reduce the ablation efficiency due to insufficient pulse fluences. Burst duration and fluence are determined to have the greatest impact on HAZ thickness. To minimize HAZ, the burst duration needs to be short, by raising repetition rates or reducing pulse numbers, to decrease the thermal diffusion time. The dependences of ablation optimum and threshold fluences on pulse numbers and repetition rates are analyzed and summarized in simple formulae. This study unveils the impacts of laser parameters in ULBA and provides guidelines for ablation efficiency and HAZ optimization.