Geometric Measurements Research Articles

First model of industrial noise propagation in the vicinity of the Yasuní National Park

Abstract This work addresses aspects of industrial noise produced by the facilities of oil extraction near Yasuní National Park, located in the Ecuadorian Amazon region. The acoustic sources within this kind of facilities could influence in the wildlife behavior, which could impact negatively on the species. The acoustic wave radial propagation model in an open field is proposed through a geometric divergence attenuation, atmospheric absorption effect, dispersion effects due to obstacles, and soil effects. The initial model without obstacles makes predictions based on an algorithm considering that the data are associated to a GPS position, the first propagation model without obstacles determines the level of sound pressure for each quasi-horizontal measurement (x, y). Then, dispersion factors are incorporated through the NORD2000 model to consider the local flora that introduces reflection and dispersion phenomena which are in the environment considering geometric measurements estimated in situ. The pressure level of the model without obstacles decreases as the frequency increases, but with less intensity compared to the pressure level of the model with obstacles. As the frequency increases, there are important fluctuations since the attenuating factors influence more than the correction factors.

Integration of Sm2Co17 Micromagnets in a Ferromagnetic Multipolar Microrotor to Enhance MEMS and Micromotor Performance.

MEMS and micromotors may benefit from the increasing complexity of rotors by integrating a larger number of magnetic dipoles. In this article, a new microassembly and bonding process to integrate multiple Sm2Co17 micromagnets in a ferromagnetic core is presented. We experimentally demonstrate the feasibility of a multipolar micrometric magnetic rotor with 11 magnetic dipoles made of N35 Sm2Co17 micromagnets (length below 250 μm and thickness of 65 μm), integrated on a ferromagnetic core. We explain the micromanufacturing methods and the multistep microassembly process. The core is manufactured on ferromagnetic alloy Fe49Co49V2 and has an external diameter of 800 μm and a thickness of 200 μm. Magnetic and geometric measurements show good geometric fitting and planarity. The manufactured microrotor also shows good agreement among the magnetic measurements and the magnetic simulations which means that there is no magnetic degradation of the permanent magnet during the manufacturing and assembly process. This technique enables new design possibilities to significantly increase the performance of micromotors or MEMS.

Experimental study on compressive capacity of stainless steel S35657 columns with welded box section and I-section under axial compression

Compared with conventional stainless steel, a new type of stainless steel, S35657, has broad application prospects owing to its advantages of high strength and low production costs. In this study, the compressive capacity of stainless steel S35657 columns was investigated. A total of 13 specimens were designed and tested, including 4 box section specimens and 9 I-section specimens (4 buckling around the major axis and 5 buckling around the minor axis). Complementary chemical composition analyses, material tensile tests, residual stress measurements, and initial geometric imperfection measurements were also conducted. The mechanical properties of the material, as well as its residual stress distribution model, failure mode, load-displacement curve, and compressive capacity, were reported and analyzed. For box section columns, when the slenderness ratio increased from 29 to 55.2, the compressive capacity of the column decreased by 27.6 %. The accuracy and safety of design methods specified in European standard EN 1993–1–4, American specification ASCE-8–02, and Chinese specification CECS 410 were assessed based on the test results. The result shows that EN 1993–1–4 is overly conservative in its compressive capacity calculations, whereas ASCE-8–02 overestimates the compressive capacity with a higher level of scatter exhibited. The methods of CECS 410 for predicting the compressive capacity of welded stainless steel S35657 columns are more accurate compared with the methods of EN 1993–1–4 and ASCE-8–02.

Pin-ended stainless steel equal-leg angle section members under compression and major-axis bending: Experimentation, FE modelling and design

The behaviour and design of cylindrically-pinned stainless steel equal-leg angle section members under compression and compression combined with strong-axis bending are investigated herein. An experimental investigation, including material testing, initial geometric imperfection measurements and physical tests on hot-rolled stainless steel equal-leg angle section members is first presented. Numerical models are developed by means of shell finite element modelling formulated within ABAQUS and validated against experimental data. A numerical parametric study is then presented considering both hot-rolled and cold-formed stainless steel equal-leg angle section columns alongside beam–columns with a wide range of cross-section and member geometries. Finally, new design proposals for cylindrically-pinned stainless steel equal-leg angle section members under compression and compression plus major-axis bending are developed and verified against the results of physical experiments and numerical simulations. The proposed design rules are shown to offer substantially more accurate and consistent resistance predictions compared to existing codified design rules. The reliability of the new design provisions, with a recommended partial safety factor γM1=1.1, is verified following the EN 1990 procedure.

Effect of hot water maceration, rehydration, and soft tissue presence on 3D geometry of bone.

In forensic medicine, maceration is often essential for examining bone surfaces, serving purposes such as identifying cut marks, making geometric measurements, and determining the victim's age. While hot water maceration removes soft tissue effectively, it is known to cause bone surface shrinkage. This raises the question of whether this effect is permanent or if it can be partially reversed through rehydration, considering the presence of soft tissue. Computed tomography (CT) scans were conducted on the radii of 20 paired human anatomic forearm specimens. Subsequently, the radii were extracted, macerated in 60 °C water, CT-scanned in an air environment, rehydrated, re-implanted into the forearms, and CT-scanned again. Maceration resulted in a mean shrinkage of 0.12mm on the outer bone surface. This shrinkage was nearly fully recoverable for the diaphysis after rehydration and accounting for soft tissue surrounding the bone. In contrast, the epiphysis showed permanent shrinkage, likely due to the loss of small bone fragments. Analysis of the inner bone surface indicated a smaller effect, but with significant standard deviations, especially for the epiphysis, possibly related to the less well-defined nature of the inner bone surface. The epiphyseal surface of hot water-macerated bone will, on average, be approximately 0.15mm deflated and cannot retain the original surface. On the other hand, the diaphyseal surface is less affected and can be nearly completely restored after rehydration and accounting for soft tissue surrounding the bone.

Open-source data alternatives for regenerating urban road fine-grained features

The extraction of urban road features provides indispensable support to numerous high-accurate applications such as autonomous driving and urban high-definition mapping. However, approaches mainly focus on road connectivity, while often overlooking finer details of urban road constituent structures. Data that captures road details, such as LiDAR, may not be always readily available. This article proposes an operational framework for mapping fine-grained urban road features by integrating open-source data (OSD). The geometric measurement method is successively presented using projective geometry and prior knowledge for urban road sections. And a feature generation strategy is introduced to achieve and express the fine-grained road features. Compared with the corresponding large-scale topographic map (LTM) and available optical remote sensing image (AORSI), the proposed method regenerated fine-grained features of urban roads with m-level. It provides a cost-effective innovative and alternative method to acquiring fine-grained road datasets in other data-scarce regions.

ZOLLINGER LAMELLA VAULT OF EXISTING TIMBER HANGARS IN ŠIBENIK (CASE STUDY) – INITIAL CONDITION ASSESSMENT AND PRELIMINARY ANALYSIS OF GLOBAL STRUCTURAL FEATURES

<p class="KEYWORDS" style="text-align: justify;">A preliminary condition assessment using non-destructive testing methods for determining material quality, has been carried out on three adjacent wooden hangars near Šibenik with the aim of exploring the possibilities of their repurposing. Through visual inspection and detailed geometric measurements, it has been verified that their unique structure embodies the original Zollinger lamella vault system in which the joint typology is decisive for both, the overarching structural analysis and the execution of the structure. In this paper, the results of conducted investigation, including the developed detailed geometric model are presented, and guidelines for future comprehensive research focusing on the influence of joint stiffness on global structural features are discussed, as well.</p>

Experimental study of wire arc additively manufactured steel sections stiffened by sinusoidal waves

Numerical models and initial tests conducted on specimens produced using selective laser melting have indicated that structural sections may be stiffened by imposing sinusoidal waveforms on their geometries which delay buckling and improve the overall buckling resistance. Wire arc additive manufacturing (WAAM) stands out as the most promising additive manufacturing technique for fabricating sections of the scale required in the construction industry, however, there is currently a lack of understanding of how the undulating surface finish inherent to WAAM will affect the stiffening effect of the sinusoidal waveforms. Therefore, this paper details an experimental study involving ten WAAM equal angle sections stiffened with two different sinusoidal wave patterns identified as the optimal patterns in previous numerical analysis. The production, geometric measurement and testing of the sections are described and the material properties of the WAAM material are determined. All equal angle section specimens tested fall within Eurocode 3 Class 4 and the stiffening wave patterns are shown to benefit the slenderer sections more. Comparative analysis between the material consumption and relative strength is provided, highlighting the potential for sinusoidal WAAM sections to improve the material efficiency and facilitate economic design practices within the steel construction industry.

Development and validation of an ex vivo porcine model of functional tricuspid regurgitation

Background and Aim: Ex vivo models of functional tricuspid regurgitation (FTR) are needed for pre-clinical testing of novel surgical and interventional repair strategies, but current options are costly or have not been formally validated. The objective of this research was to create and validate an ex vivo model to test novel repair methods for FTR. Methods: In explanted porcine hearts, the right atrium was excised to visualize the tricuspid valve. The pulmonary artery and aorta were clamped and cannulated, the coronary arteries ligated, and the right and left ventricles statically pressurized with air to 30 mmHg and 120 mmHg, respectively. FTR was induced by increasing right ventricular pressure to 80 mmHg for 3 h, which resulted in progressive tricuspid annular enlargement, right ventricular dilation, papillary muscle displacement, and central tricuspid malcoaptation. A structured light scanner was used to image the 3D topography of the tricuspid valve in both the native and FTR state, and images were exported into scan-to-computer-aided design software, which allowed for high-resolution 3D computational reconstruction. Relevant geometric measurements were sampled including annular circumference and area, major and minor axis diameter, and tenting height, angle, and area. Geometric measurements from the ex vivo model were compared to clinical transthoracic echocardiographic (TTE) measurements using two-sample t-tests. Results: A total of 12 porcine hearts were included in the study. Annular measurements of the native valve were comparable to published TTE data, except for the minor axis diameter, which was shorter in the ex vivo model (2.5 vs. 3.1 cm, P = 0.007). Induction of FTR in the ex vivo model resulted in annular enlargement (FTR vs. native: circumference 13.7 vs.11.8 cm, P = 0.012; area 14 vs. 11 cm2, P = 0.011). Ex vivo leaflet measurements in both the native and FTR model differed from published TTE data, but demonstrated comparable directional changes between the native and regurgitant states, including increased tenting height, area, and volume. Conclusion: The ex vivo pneumatically-pressurized porcine model closely recapitulates the geometry of both the native and regurgitant tricuspid valve complex in humans and holds promise for testing novel FTR repair strategies. Relevance for Patients: Currently available interventions for the tricuspid valve have a risk of permanent conduction abnormalities and are insufficient in addressing tricuspid disease for a subset of patients. This ex vivo model provides a platform for testing of novel interventions that address the deficiencies of current tricuspid therapies.

Analysis of Long-Distance Geometric Error Measurement and Uncertainty Based on PSD Laser Collimation Principle

Due to the limitations of traditional geometric error measurement, the measurement accuracy of long-stroke geometric errors is generally not high and the operation is complicated. In response to the above situation, in this study, a geometric error measurement system is built with a laser beam as the reference line and 2D position sensitive detector as the photoelectric conversion device. The single measurement range is 40 m, and the measurement range is further expanded through the principle of segmented splicing. Using an ultra-long guide rail as the measurement object for straightness measurement, the experimental results are similar to those of a laser interferometer. The uncertainty analysis model was obtained through the analysis of quantity characteristics, and based on this, the variance synthesis theorem and probability distribution propagation principle were studied to form two uncertainty synthesis methods. The measurement evaluation results showed that the two methods were basically consistent. The work provided a reference method for the uncertainty evaluation of position-sensitive detector measurement systems in the future.

82‐1: Distinguished Paper: Geometric Distortion on Video See‐Through Head‐Mounted Displays

We evaluate the geometric distortion on video see‐through (VST) head‐mounted displays (HMDs) with single‐camera and dualcamera design. We present the experimental setup and metrology for geometric calibration and VST geometric distortion measurement. Physical geometric distortion is compared to the distortion of digital content on a VST HMD. We investigate the impacts of camera misalignment and depth distance on VST geometric distortion with angular‐based distortion correction.

The Role of Lipid Intrinsic Curvature in the Droplet Interface Bilayer.

Model bilayers are constructed from lipids having different intrinsic curvatures using the droplet interface bilayer (DIB) method, and their static physicochemical properties are determined. Geometrical and tensiometric measurements are used to derive the free energy of formation (ΔF) of a two-droplet DIB relative to a pair of isolated aqueous droplets, each decorated with a phospholipid monolayer. The lipid molecules employed have different headgroup sizes but identical hydrophobic tail structure, and each is characterized by an intrinsic curvature value (c0) that increases in absolute value with decreasing size of headgroup. Mixtures of lipids at different ratios were also investigated. The role of curvature stress on the values of ΔF of the respective lipid bilayers in these model membranes is discussed and is illuminated by the observation of a decrement in ΔF that scales as a near linear function of c02. Overall, the results reveal an association that should prove useful in studies of ion channels and other membrane proteins embedded in model droplet bilayer systems that will impact the understanding of protein function in cellular membranes composed of lipids of high and low curvature.

Experimental and numerical investigations of S890 and S960 ultra-high strength steel circular hollow section columns

The experimental and numerical investigations of the buckling behaviour and load-carrying capacities of S890 and S960 ultra-high strength steel (UHSS) circular hollow section (CHS) columns were conducted and reported in this paper. The experimental program encompassed tensile coupon tests, initial global and local geometric imperfection measurements and pin-ended column tests. Parallelly, the numerical modelling program was carried out, where the developed finite element (FE) models were validated with reference to the experimental observations and then employed in parametric studies to result in additional numerical data, considering various cross-sectional dimensions and member lengths. Based on the obtained FE and test data, the applicability of the relevant codified design buckling curves in the current European, Australian and American specifications to S890 and S960 UHSS CHS columns was evaluated, since the aforementioned standards only cover the design rules with steel material yield strength no greater than 700 MPa. The assessment results showed that the European code and Australian standard can generally accurately predict the resistances of S890 and S960 UHSS CHS columns, but result in some unsafe data points, while the American specification yielded accurate and consistent resistance predictions. Finally, a revised Eurocode design buckling curve was proposed, accompanied by the reliability assessment through statistical analyses, with the improved design accuracy and consistency revealed.

Evaluating geometric measurement accuracy based on 3D model reconstruction of nursery tomato plants by Agisoft photoscan software

Measuring the vegetation structure of a plant with the help of 3D images is a non-destructive method that can be used to monitor the plant’s status during the growing season. Structure from motion (SfM) is a popular optical distance measurement method that uses 2D images to create 3D models. Identifying factors that influence the precision of SfM is important due to its increasing use in phenotyping. The primary objectives of this study were, i) to scrutinize the impact of imaging parameters—including, color checkerboard location, overlap size of images, and background filtering—on the quality indices of 3D models, and ii) to attain precise measurements of leaf area, stem diameter, and height through the combination of images captured from different camera shooting angles. The three nursery tomato plants were photographed at every five-degree rotation of the turntable, five different locations of color checkerboards, and five camera shooting angles. Results indicated the color checkerboard’s presence and position affect the quality indices of the 3D models. Visually and by the lowest mean keypoint size value, the least noisy 3D model was obtained when the wall of the plant pot was covered with a checkerboard. When the base-to-distance (b/y) ratio as the image overlap index increased from 0.1 to 0.2, the generation time of the 3D models decreased by more than two times. Optimal Mean Absolute Percentage Error (MAPE) values of 1.08 %, 1.01 %, and 1.38 % were achieved for the estimation of leaf area, stem diameter, and height, respectively. This was recorded by using images taken at 0°, 30°, and 105° vertical azimuth angles. Constructing a 3D model by integrating images captured from other angles or more azimuth angles represents numerous visual challenges and leads to problems of point mismatch, which affects the accuracy of measurements.

Geometric distortion on video see‐through head‐mounted displays

AbstractVideo see‐through (VST) head‐mounted displays (HMDs) reconstruct the physical world using outward‐facing cameras and depth sensors. One of the major challenges for VST HMDs is the geometric distortion of the physical pass‐through content. In this study, we present the experimental setup and metrology for VST geometric distortion measurement on single‐camera and dual‐camera VST HMDs. The VST geometric distortion is compared to the digital distortion by the HMD. Finally, we investigate the impacts of camera misalignment and depth distance on VST geometric distortion without and with angular‐based distortion correction. The results demonstrate that camera misalignment with respect to the eye position is the primary root cause for the distortion. Dual‐camera setup is necessary to minimize the VST geometric distortion by placing the cameras close to the eye positions. Although distortion correction can partially mitigate VST geometric distortion in a 2D plane, it remains a challenge for VST distortion correction at multiple depth distance in the 3D space. The method and findings presented of this study may provide guidelines for evaluation of spatial accuracy on VST HMDs and hardware design.

Research on Geometric Measurement Technology of the Inner Cavity of Cylindrical Parts

Research on Geometric Measurement Technology of the Inner Cavity of Cylindrical Parts

Tip of the Red Giant Branch Distances with JWST: An Absolute Calibration in NGC 4258 and First Applications to Type Ia Supernova Hosts

The tip of the red giant branch (TRGB) allows for the measurement of precise and accurate distances to nearby galaxies based on the brightest ascent of low-mass red giant branch stars before they undergo the helium flash. With the advent of JWST, there is great promise to utilize the technique to measure galaxy distances out to at least 50 Mpc, significantly further than the Hubble Space Telescope's (HST's) reach of 20 Mpc. However, with any standard candle, it is first necessary to provide an absolute reference. Here, we use Cycle 1 data to provide an absolute calibration in the F090W filter. F090W is most similar to the F814W filter commonly used for TRGB measurements with HST, which had been adopted by the community due to its minimal dependence on the underlying metallicities and ages of stars. The imaging we use was taken in the outskirts of NGC 4258, which has a direct geometrical distance measurement from the Keplerian motion of its water megamaser. Utilizing several measurement techniques, we find MTRGBF090W = −4.362 ± 0.033 (stat) ± 0.045 (sys) mag (Vega) for the metal-poor TRGB. We also perform measurements of the TRGB in two Type Ia supernova hosts, NGC 1559 and NGC 5584. We find good agreement between our TRGB distances and previous determinations of distances to these galaxies from Cepheids (Δ = 0.01 ± 0.06 mag), with these differences being too small to explain the Hubble tension (∼0.17 mag). In addition, we showcase the serendipitous discovery of a faint dwarf galaxy near NGC 5584.

Estimating the Uncertainty of Measurements for Various Methods and 3D Printed Parts

This paper presents the results of a study on the dimensional accuracy analysis of models produced by 3D printing technology—Fused Filament Fabrication (FFF). Geometric measurements were conducted using a dial caliper, a 3D scanner and a coordinate measuring machine. In addition, a statistical analysis of the test results was carried out, considering the division into different numbers of test samples (3, 5, 10, 20, 30). The analysis of the test results made it possible to assess the influence of the measuring tools used and the number of samples tested on the final measurement result, as well as to determine the consequences associated with it.

Geometric Error Measurement of Rotary Axes on Five-Axis Machine Tools: A Review

Geometric Error Measurement of Rotary Axes on Five-Axis Machine Tools: A Review

Experimental and numerical investigations of S960 hot-rolled ultra-high strength steel seamless circular hollow section beam–columns

The rapid development of manufacturing techniques and material science enables advanced hot-rolled ultra-high strength steel (UHSS) with material grades up to S960 to be available recently. The structural performance of S960 hot-rolled UHSS seamless circular hollow section (CHS) beam–columns manufactured through the advanced fabrication approach was experimentally and numerically investigated and reported in this paper. In physical testing, totally ten beam–column specimens were tested, with the complementary material testing and initial global geometric imperfection measurements through the innovative digital image correlation (DIC) method performed. FE modeling was then carried out; FE models of S960 hot-rolled UHSS seamless CHS beam–columns were established and then validated the test observations in terms of the failure loads and the load–mid-height lateral displacement curves. Parametric studies were thereafter performed, with cross-section dimensions, member lengths and loading combinations varying within a certain range, resulting in the additional 300 data to be acquired. Finally, the applicability of existing design methods, as prescribed in the European code, the Australian standard and the American specification, to S960 hot-rolled UHSS seamless CHS beam–columns was evaluated. It can be concluded from the evaluation results that all the three design codes provide accurate and consistent failure load predictions for S960 hot-rolled UHSS seamless CHS beam–columns.