Surface Of Fused-silica Capillary Research Articles

Chemical vapour deposition in narrow capillaries: Electro-osmotic flow control in capillary electrophoresis

BackgroundIn capillary electrophoresis (CE), the inner surface of fused-silica capillaries is commonly covalently modified with liquid silanes to control electroosmotic flow (EOF). This liquid phase deposition (LPD) approach is challenging for long and narrow-diameter capillaries (≥1 m, ≤25 μm ID) inhibiting commercial production. Here, we use chemical vapour deposition (CVD) to covalently modify capillaries with different silanes. Using a home-built CVD device, capillaries were modified with neutral (3-glycidyloxypropyl) trimethoxysilane (GPTMS), the weak base (3-aminopropyl) trimethoxysilane (APTMS), the weak acid 3-mercaptopropyltrimethoxysilane (MPTMS) and the neutral hydrophobic trichloro(1H,1H,2H,2H-perfluorooctyl) silane (PFOCTS). Gas-phase modification of GPTMS with acid and ammonia allowed further modification of the surface prior to molecular layer deposition (MLD) of poly(p-phenylene terephthalamide) (PPTA) using the self-limiting sequential reaction between terephthalaldehyde (TA) and p-phenylenediamine (PD) vapours. ResultsCapillaries coated with GPTMS by CVD showed a greater reduction in EOF at all pH values than the conventional LPD. APTMS showed a reduction of the EOF at pH 9, with EOF reversal observed below pH 6. MPTMS provided a slightly lower EOF than an unmodified capillary at high pH, and a slightly higher EOF at lower pH. PFOCTS provided the most consistent EOF as a function of pH. The deposition of successive layers of PPTA resulted in increased surface coverage of the polymer and a greater reduction in EOF at pH higher than 5. The stability of a 10 μm ID GPTMS coated capillary was tested at pH 8.8 in a 200 mM CHES/Tris BGE for the separation of inorganic anions. Over 1.5 months of continuous operation (≈4130 runs), the reproducibility of the apparent mobilities for chloride, nitrite, nitrate and sulfate were 2.43%, 2.56%, 2.63% and 3.05%, respectively. The intra-day and inter-day column-to-column reproducibility and batch-to-batch reproducibility for all the coated capillaries ranged between 0.34% and 3.95%. SignificanceThe study demonstrates the superior performance of CVD coating for suppressing the EOF compared to LPD allowing the easy modification of long lengths of narrow capillary. The variation in silane, and the ability of MLD to modify and control the surface chemistry, provides a simple and facile method for surface modification. The stability of these coatings will allow long-term capillary electrophoresis monitoring of water chemistry, such as for monitoring fertiliser run-off in natural waters.

Platinum nanoparticles confined in imidazolium-based ionic polymer for assembling a microfluidic reactor with enhanced catalytic activity

A synthetic strategy is developed to grow Pt nanoparticles supported by imidazolium-based ionic polymers (Pt/ImIP-2BrB) on the inner surface of fused-silica capillary. The imidazolium-based ionic polymers ImIP-2BrB are prepared from condensation of tetrakis[4-(1-imidazolyl)phenyl]methane and 1,4-bis-bromomethyl-benzene and are employed to support Pt nanoparticles. The capillary coated with Pt/ImIP-2BrB is further assembled to achieve a catalytic microfluidic reactor. The catalytic activity is probed in either the reduction of nitrobenzene derivatives or the hydrosilylation of phenylacetylene with triethylsilane by flowing through the microfluidic reactor. The catalytic microfluidic reactor demonstrates significantly enhanced activity about 2–8 times in comparison with the corresponding reactions under batch conditions. The reactor greatly reduces the amount of Pt upon achieving similar yields. It also shows good recyclability without significant decrease of the activity.

Superhydrophobic capillary coatings: Elaboration, characterization and application to electrophoretic separations

Separation efficiency is ideally controlled by molecular diffusion in capillary electrophoresis (CE). However, other adverse phenomena, such as solute adsorption on capillary surface, tend to increase the peak dispersion. An interesting alternative to limit the solute adsorption is to avoid as much as possible the contact of the solute with the capillary surface by elaborating superhydrophobic (SH) coatings on fused silica capillary surfaces. This work describes an optimized protocol to get non-wettable SH coating using hydrophobically modified silica nanoparticle suspensions (Glaco™), based on simple capillary flushes and thermal stabilization. In this protocol, the control of the air flushing after the introduction of the Glaco™ suspension in the capillary was found crucial to get optimized coating coverage and reproducibility. The SH coating was characterized by ellipsometry, atomic force microscopy, scanning electron microscopy, contact angle (about 159°) and the observation of the meniscus of water in the coated capillary. The hydrodynamic behavior of the SH coated capillary was investigated by plotting the Poiseuille law. Finally, electrophoretic separations of a peptide mixture in acidic conditions demonstrated the interest of this approach with an increase by a factor 2 of the separation efficiency compared to fused silica capillary.

Self-assembled and covalent capillary coating of diazoresin and D-Glucurone for protein analysis in capillary electrophoresis

ABSTRACTA simple, environmental and economical capillary electrophoresis method has been developed for the analysis of four model proteins by employing a photoactive and non-toxic diazoresin (DR), D-Glucurone modification of the inner surface of fused-silica capillary. DR/D-Glucurone coated capillary not only effectively eliminated the wall adsorption of proteins, but also showed good stability and repeatability. Instead of using the moisture sensitive and toxic silane coupling agent, the application of photosensitive DR may provide a flexible and environmentally friendly strategy to prepare novel covalently coated capillaries. Thus, DR/D-Glucurone coated capillary has great potential in capillary electrochromatography and may provide a new method for biological compounds separation.

Immobilized capillary tyrosinase microreactor for inhibitor screening in natural extracts by capillary electrophoresis

A method for creating an immobilized capillary tyrosinase (TRS) reactor based on a layer-by-layer (LBL) assembly for inhibitor screening is described. Tyrosinase was immobilized on the surface of fused-silica capillary via ionic binding technique with cationic polyelectrolyte hexadimethrine bromide (HDB). Then, HDB solution with the same plug length as the TRS was injected again into the capillary to cover the immobilized enzyme by forming HDB–TRS–HDB sandwich-like structure. Then, the substrate of l-tyrosine was introduced into the capillary and on-line enzyme inhibition study was performed by capillary electrophoresis (CE). The enzyme activity was determined by the quantification of peak area of the product of l-DOPA. Enzyme inhibition can be read out directly from the reduced peak area of the product in comparison with a reference electropherogram obtained in the absence of any inhibitor. The immobilized enzyme could withstand 25 consecutive assays by only losing 12% activity. A known TRS inhibitor, kojic acid was employed as a model compound for the validation of the inhibitor screening method. Finally, screening 19 natural extracts of traditional Chinese drugs was demonstrated. The results indicated that inhibition activity could be straightforwardly identified with the system.

Surface initiated polymerization of a cationic monomer on inner surfaces of silica capillaries: Analyte separation by capillary electrophoresis versus polyelectrolyte behavior

[2-(Methacryloyl)oxyethyl]trimethylammonium chloride was successfully polymerized by surface-initiated atom transfer radical polymerization method on the inner surface of fused-silica capillaries resulting in a covalently bound poly([2-(methacryloyl)oxyethyl]trimethylammonium chloride) coating. The coated capillaries provided in capillary electrophoresis an excellent run-to-run repeatability, capillary-to-capillary and day-to-day reproducibility. The capillaries worked reliably over 1 month with EOF repeatability below 0.5%. The positively charged coated capillaries were successfully applied to the capillary electrophoretic separation of three standard proteins and five β-blockers with the separation efficiencies ranging from 132,000 to 303,000 plates/m, and from 82,000 to 189,000 plates/m, respectively. In addition, challenging high- and low-density lipoprotein particles could be separated. The hydrodynamic sizes of free polymer chains in buffers used in the capillary electrophoretic experiments were measured for the characterization of the coatings.

On-line immobilized acetylcholinesterase microreactor for screening of inhibitors from natural extracts by capillary electrophoresis

In this study we developed a simple capillary electrophoresis (CE) method with an on-line acetylcholinesterase (AChE) microreactor at the inlet of capillary for inhibitor screening. The fused-silica capillary surface was modified with a polycationic polyethylenimine coating. Solutions of the enzyme and chitosan were then injected to immobilize the enzyme in approximately 2.9 cm of the capillary inlet (total length of capillary 60.2 cm) by electrostatic interaction and the film overlay technique. Separation of enzyme reaction product (thiocholine, ThCh) and unreacted substrate (acetylthiocholine, AThCh) was achieved within 3.0 min. The conditions affecting the efficiency of reaction of the enzyme were optimized by measuring the peak area of ThCh. Under the optimum conditions, using Huperzine-A as model inhibitor, K (i) and IC (50) were 0.551 μmol L(-1) and 1.52 μmol L(-1), respectively, for immobilized AChE. Finally, screening of a small compound library containing two known AChE inhibitors and 30 natural extracts was conducted, and species with inhibition activity were directly identified. Compared with previous publications on screening for AChE inhibitors in natural products based on CE methods, the method developed in this work has the advantages of lower cost per analysis, less leakage, and better bioaffinity for the immobilized enzyme because of the unique properties of sodium alginate and chitosan.

An enzyme immobilized microassay in capillary electrophoresis for characterization and inhibition studies of alkaline phosphatases

A simple and fast dynamically coated capillary electrophoretic method was developed for the characterization and inhibition studies of alkaline phosphatases (EC 3.1.3.1). An inside capillary enzymatic reaction was performed, and hydrolysis of the substrate 4-nitrophenylphosphate to 4-nitrophenol was measured. Fused-silica capillary surface was dynamically modified with polycationic polybrene coating. By reversal of the electroosmotic flow (EOF), analysis time was reduced up to 3 min as the anionic analytes were migrated in the same direction as the EOF. Furthermore, the sensitivity of the method was increased using electroinjection through high-field amplified injection. The baseline separation of 4-nitrophenylphosphate and 4-nitrophenol was achieved by employing 50 mM sodium phosphate as the running buffer (pH 8.5), 0.0025% polybrene, and a constant voltage of −15 kV, and the products were detected at 322 nm. Under the optimized conditions, a good separation with high efficiency was achieved. The new method was applied to study enzyme kinetics and inhibitor screening. K m and K i values obtained with the new CE method were compared well with the standard spectrophotometric method. Dynamic coating of fused-silica capillary gave fast and reproducible separation of substrate and product. The method can be easily optimized for inhibition studies of other isozymes.

Polymeric ionic liquid as a dynamic coating additive for separation of basic proteins by capillary electrophoresis

A simple and economical capillary electrophoresis method has been developed for the analysis of four model basic proteins by employing a polymeric ionic liquid (PIL), poly(1-vinyl-3-butylimidazolium) bromide, as the dynamic coating additive. When a small amount of PIL was present in the background electrolyte, a cationic coating on the inner surface of fused-silica capillary was established. These PIL modified capillaries not only generated a stable reversed electroosmotic flow, but also effectively eliminated the wall adsorption of proteins. Several important parameters such as the PIL concentration in the background electrolyte, pH values and concentrations of the background electrolyte were optimized to improve the separation of basic proteins. Consequently, under the optimum conditions, a satisfied separation of basic proteins with peak efficiencies ranging from 247,000 to 540,000 (plates m −1) had been accomplished within 11 min. The run-to-run RSDs ( n = 3) of the migration times for the four basic proteins were all less than 0.37%.

Immobilized capillary adenosine deaminase microreactor for inhibitor screening in natural extracts by capillary electrophoresis

A novel strategy for the preparation of in-column adenosine deaminase (ADA) microreactor and rapid screening of enzyme inhibitors in natural extracts was demonstrated. In this approach, ADA was encapsulated in anionic polyelectrolyte alginate that was immobilized on the surface of fused-silica capillary via ionic binding technique with cationic polyelectrolyte polyethylenimine (PEI). On-line enzyme inhibition study was performed by capillary electrophoresis (CE). The substrate and product were baselined separated within 75 s. The enzyme activity was determined by the quantification of peak area of the product. Enzyme inhibition can be read out directly from the reduced peak area of the product in comparison with a reference electropherogram obtained in the absence of any inhibitor. The inhibition percentage was used to evaluate relative activity of ADA microreactor. A known ADA inhibitor, erythro-9-(2-hydroxy-3-nonyl) adenine (EHNA) was employed as a model compound for the validation of the inhibitor screening method, and the screening of ADA inhibitor in 19 traditional Chinese herbal medicines was performed.

PREVENTION OF PROTEIN ADSORPTION ON BARE FUSED-SILICA CAPILLARY BY PEG IN CAPILLARY ZONE ELECTROPHORESIS

The protein separation was studied in capillary zone electrophoresis for preventing protein adsorption on the capillary wall. ß-lactoglobulin (pI: 4.83-5.4, Mr: 18.4 kDa), cytochrome c (pI: 9.59, Mr: 11.7 kDa) and ß-casein (pI: 4.6, Mr: 24 kDa) were used as protein models. Strong adsorption of the proteins occurred onto the capillary at a pH around their pIs. In order to prevent protein adsorption, PEG (Poly(ethylene glycol)) was investigated as an effective substance to stabilize the proteins native state and coat the bare fused-silica capillary surface. The presence of 32 mg/mL PEG in buffer solution in a pH range of 6.0 to 4.0 was successful to suppress protein adsorption during the separation. It can also be confirmed with the reproducibility of apparent EOF mobility with percentile RSD (Relative Standard Deviation) less than 2% in long-term measurement. Keywords: PEG, protein adsorption, CZE

Protein attachment onto silica surfaces – a survey of molecular fundamentals, resulting effects and novel preventive strategies in CE

This review addresses the fundamentals governing the adsorption of individual protein molecules onto the surface of fused-silica capillaries, the protein aggregation to adsorbate clusters and their final accretion to monolayers with subsequent stratification to protein multilayers. The attention in CE protein separation has primarily been focused on (i) tuning the BGE including the buffer type, ionic strength, pH and additives, (ii) tailored post-rinse procedures to detach adhered protein residues and (iii) the optimization of capillary wall shielding in order to reduce protein attachment. Improvements in protein separation as well as related adverse effects are mainly discussed on the basis of parameters known to become deteriorated in case of protein adhesion, e.g. repeatability of the EOF and of migration times, peak width, theoretical plate numbers, resolution and asymmetry factor. However, knowledge of the molecular principles controlling protein adsorption onto silica surfaces is indispensable for separation optimization. Furthermore, it facilitates troubleshooting and the interpretation of undesired concomitant phenomena. This review comprehensively discusses protein adsorption models derived from surface chemistry primarily in terms of their relevance for CE, clearly showing that the adsorption process in its complexity is only partially revealed by models, which address single or binary protein solutions. In a further section theoretical concepts and surface models are related to surface phenomena encountered in CE. The final part of the review surveys recent concepts for prevention of protein adhesion, thereby addressing capillary treatment, favorable buffer types, dynamic and adhesive semi-permanent coating strategies covering the literature from 2000-2008.

Silanizing agent for semipermanent wall coating in micellar electrokinetic capillary chromatography

In this paper, the long-chained, silanizing agent chloro(dodecyl)dimethylsilane (CDDS) was investigated as a semipermanent coating in micellar electrokinetic capillary chromatography (MEKC). CDDS coating had great stability due to the formation of covalent bonding with the silanol groups on the surface of fused-silica capillary and remained stable for over 100 min after removal of the rinse step of CDDS solution. Anionic surfactant sodium dodecyl sulfate (SDS) could aggregate at this CDDS coating by the hydrophobic group and formed a SDS layer which could increase the electroosmotic flow (EOF). The separation was performed with the running buffer composed of 60 mM sodium tetraborate, 12 mM SDS at pH 9.9, with the applied voltage of 20 kV and capillary temperature 25 °C. The effect of the coating agent was investigated by the analysis of amino acids. Compared with previous no-coating method, the EOF increases from 4.34 × 10 −4 cm 2 V −1 s −1 to 7.02 × 10 −4 cm 2 V −1 s −1. Migration time reproducibility was less than 0.97% R.S.D. from run to run and less than 1.56% R.S.D. from day to day.

Novel adsorptive polyamine coating for enhanced capillary electrophoresis of basic proteins and peptides

In capillary electrophoresis (CE), the anionic and hydrophobic nature of the fused-silica capillary surface has long been known to present a problem in protein and peptide analysis. The use of capillary surface coating is one of the approaches to avoid the analyte-wall interactions. In this study, a new polymer, poly-LA 313, has been synthesized, physico-chemical characterized, and applied as polyamine coating for CE separations. The coating process is highly reproducible and provides fast separations of peptides and proteins in a few minutes and with high efficiency. The physically adsorbed polymer gives rise to a durable coating in the range of pH 2-10, in the presence of organic modifiers (acetonitrile and methanol) and with complex biological samples. The efficiency of the new cationic polymer was also tested performing protein and peptide separations with capillary electrophoresis-electrospray ionization-mass spectrometry (CE-ESI-MS).

Cationic amylopectin derivatives as additives for analysis of proteins in capillary electrophoresis

Positively charged amylopectin, which is a major constituent of cationic starch, was used to modify the inner surface of fused-silica capillaries by addition to the running solution, which was subsequently employed in CE. Capillaries filled with cationic amylopectin derivatives were shown to generate a stable reversed EOF in the investigated range of pH 4-8. Among the additives studied, quaternary ammonium amylopectin derivatives with high amino and low hydroxypropyl groups showed fast electroosmotic mobility and very effectively suppressed the adsorption of proteins. The run-to-run and batch-to-batch repeatability of the procedures were satisfactory with RSDs of 0.5% and 2.4%, respectively. A basic protein, alpha-chymotrypsinogen, migrated within 6 min and the theoretical plate number of it reached 560 000 plates/m.

Utilizing the pH hysteresis effect for versatile and simple electrophoretic analysis of proteins in bare fused-silica capillaries

The analysis of peptides and proteins by CE is often desirable due to low sample consumption and possibilities for nondenaturing yet highly effective separations. However, adsorption to the inner surfaces of fused-silica capillaries often is detrimental to such analyses. This phenomenon is especially pronounced in the analysis of basic proteins and proteins containing exposed positively charged patches. To avoid wall interactions numerous buffer additives and static and dynamic wall coating principles have been devised. We previously showed (J. Chromatogr. A 2004, 1059, 215-222) that CE of the basic protein beta2-glycoprotein was rendered possible by an acidic pretreatment step, and we attributed this observation to the so-called pH hysteresis effect that influences the time for pH equilibration of the capillary wall and thus the effective wall charge and the electroosmotic mobility. We here investigate the effects of different pretreatment techniques on EOF values and on the rate of the deprotonation of silanol groups when performing the electrophoresis at neutral pH. We show the utility of this simple approach for the CE analysis of a number of basic proteins in plain silica capillaries at physiological pH.

Cationic starch derivatives as dynamic coating additives for protein analysis in capillary electrophoresis

Positively charged starch derivatives were used to modify the inner surface of fused-silica capillaries by addition to running buffer, which were subsequently employed in capillary electrophoresis (CE). Capillaries coated with the cationic starch derivatives were shown to generate a stable, reversed electroosmotic flow (EOF) in the investigated pH range of 3–9. The presented coating procedure was fast, based on a simple rinsing protocol where the polymer created a physically adsorbed, cationic polymer layer. Among the additives studied, a quaternary ammonium starch derivative showed a fast EOF mobility and effectively suppressed the adsorption of proteins. The intra- and inter-day reproducibility of the coating referring to the EOF mobility were satisfactory with relative standard deviation (RSD) of 0.27 and 1.67%, respectively. The coating enabled separation of some protein mixtures including basic proteins within l3 min with efficiencies up to 280,000 plates/m. In addition, this cationic starch derivative possessed a good solubility (about 100 mg/mL), and it does not significantly contribute to the background adsorption in the UV region of 190–400 nm.

Approaches for the coating of capillary columns with highly phenylated stationary phases for high-temperature GC.

Two highly phenylated tetramethyl-p-silphenylene-diphenylsiloxane copolymers were coated on fused silica capillary columns and used as stationary phases in GC. The copolymers offered new insights into the coating process and column preparation due to their physicochemical properties. The fused silica capillary surface had to be pretreated in various ways to achieve a homogeneous film and a well deactivated surface: etching with ammonium bifluoride; leaching with sodium hydroxide and hydrochloric acid; silylation with tetraphenyldimethyldisilazane and triphenylsilylamine. Droplet formation was observed on tetraphenyldimethyldisilazane silylated surfaces leading to capillary columns with low separation efficiency. The topology of inhomogeneous films was investigated by light microscopy, scanning electron microscopy, and Auger electron spectroscopy. It became apparent that the stationary phase did not form droplets but islands, which are connected by a wetting layer according to the Stranski-Krastanov growth mode. Both copolymers are potential stationary phases for high-temperature GC with promising properties. They offer a higher overall polarity than 75% phenyl, 25% methyl-polysiloxanes in combination with increased thermal stability and reduced bleed levels.

Novel polyamine coating providing non-covalent deactivation and reversed electroosmotic flow of fused-silica capillaries for capillary electrophoresis

A new polycationic coating for use in capillary electrophoresis has been developed that enables chemical modification of fused-silica capillary surfaces for analysis of compounds like basic proteins. The cationic polyamine, containing short aliphatic blocks of combined 2 and 3-carbon length, was physically adsorbed onto the negatively charged fused-silica surface through ionic interaction by flushing the capillary with a polyamine solution, followed by a self-stabilization step. The polyamine coated capillaries generated an anodal electroosmotic flow that was independent of pH in the investigated range of pH 4–8. The capillary performance was demonstrated by fast separations of basic proteins with peak efficiencies in the range of 265 000–584 000 plates.

Separation of structurally related peptides by open-tubular capillary electrochromatography using (metallo)porphyrins as the adsorbed stationary phase

Several (metallo)porphyrins, particularly the porphyrin derivative tetraphenylporphyrin, and complexes of porphyrin derivatives with metal ions (Zn 2+, Cu 2+, Ni 2+, Co 2+, Co 3+) have been employed as the stationary phase physically adsorbed onto the inner fused-silica capillary surface for open-tubular capillary electrochromatography, and applied for the separation of structurally related peptides. Four octapeptides, derivatives of the B23–B30 fragment of the B-chain of human insulin with minor changes in their sequences (presence of lysine or ornithine in position B-29, presence or absence of phenylacetyl protecting group on the amino group of lysine/ornithine or N-terminal amino group of glycine), were studied as model analytes. Separations were performed both in alkaline (pH 9.0) and in acidic (pH 2.25) background electrolytes, and the changes in the migration/retention behaviour of the model set of peptides were investigated with respect to the porphyrin periphery/central metal atom and the charge of the octapeptides modified. The key moment of successful separation of these peptides seems to be the accessibility of functional groups of the peptides to the interaction with the modifiers tested herein.