Functional Nanoparticles Research Articles

Laser-induced emission from iron oxide nanoparticles in spray-flame synthesis: in situ high-speed microscopy

Spray-flame synthesis uses low-cost precursors dissolved in organic solvents to produce functional metaloxide nanoparticles. In the spray flame, the precursor-laden droplets show frequent and intense thermally-induced disruption, so-called puffing and micro-explosion. This process is often correlated with high uniformity of particle sizes. Whether puffing and micro-explosion are also directly associated with the formation or release of iron oxide nanoparticles is not clear. Also, the spatiotemporal evolution of nanoparticles in the turbulent flow field of the flame is largely unknown from experiments. We performed simultaneous high-speed microscopic imaging of droplet shadowgraphs at 360 kHz as well as elastic light scattering (ELS) and laser-induced emission (LIE) of nanoparticles at 40 kHz. Comparing ELS and LIE images allows distinguishing signals from droplets, flame, and nanoparticles, as only the nanoparticles will appear in images from both methods. ELS and LIE show nanoparticles as thin narrow filaments, presumably following the local flow. Nanoparticle filaments are found at a height of 50 mm and more above the burner in the spray flame. The filaments show increasing LIE signal and higher confinement with increasing height above the burner. The appearance of LIE and thus nanoparticles does not directly correlate with the presence of droplets or their disruption.

High performance bimetallic ZIF-CoZn@PVDF-HFP composite nanofiber membrane for membrane distillation based on coaxial electrospinning technology

Membrane Distillation (MD) technology stands out for its cost-effectiveness and sustainability in diverse applications, such as high-salinity wastewater treatment and seawater desalination. However, conventional MD membranes frequently encounter challenges associated with inadequate permeate flux and insufficient anti-wetting performance. In the present study, we fabricated a series of ZIF-CoZn@PVDF-HFP composite nanofiber membranes with a core–shell structure via coaxial electrospinning. Here, PVDF-HFP functions as the core, while a blend of bimetallic Zeolitic imidazolate framework ZIF-CoZn nanoparticles and PVDF-HFP constitutes the shell. Through the utilization of the coaxial technology, functional nanoparticles achieve uniform and stably dispersed on the nanofiber surface, leading to the creation of a secondary rough structure in addition to the inherent roughness of single-nozzle electrospinning. This results in a surface with a 3D-hierarchical structure. The significantly amplifies the evaporation area on the surface of the composite nanofiber membrane, thereby bolstering the permeate flux in the MD process. Additionally, the incorporation of bimetallic ZIF-CoZn nanoparticles, recognized for their superior hydrophobicity and low thermal conductivity, improves the anti-wetting and heat-insulating properties of the composite nanofiber membrane, further advancing permeate flux performance. Using a 35 g L−1 NaCl as the feed solution, the optimal 1 % ZIF-CoZn@PVDF-HFP composite nanofiber membrane demonstrated a permeate flux of 21.8 L m−2 h−1, coupled with a salt rejection rate exceeding 99.9 %. Even during long-term MD testing, it maintained excellent insulation and anti-wetting capabilities. Our research offers a convenient and effective approach for fabricating anti-wetting composite nanofiber membranes.

Functional Polyphenol-Based Nanoparticles Boosted the Neuroprotective Effect of Riluzole for Acute Spinal Cord Injury.

Riluzole is commonly used as a neuroprotective agent for treating traumatic spinal cord injury (SCI), which works by blocking the influx of sodium and calcium ions and reducing glutamate activity. However, its clinical application is limited because of its poor solubility, short half-life, potential organ toxicity, and insufficient bioabilities toward upregulated inflammation and oxidative stress levels. To address this issue, epigallocatechin gallate (EGCG), a natural polyphenol, was employed to fabricate nanoparticles (NPs) with riluzole to enhance the neuroprotective effects. The resulting NPs demonstrated good biocompatibility, excellent antioxidative properties, and promising regulation effects from the M1 to M2 macrophages. Furthermore, an in vivo SCI model was successfully established, and NPs could be obviously aggregated at the SCI site. More interestingly, excellent neuroprotective properties of NPs through regulating the levels of oxidative stress, inflammation, and ion channels could be fully demonstrated in vivo by RNA sequencing and sophisticated biochemistry evaluations. Together, the work provided new opportunities toward the design and fabrication of robust and multifunctional NPs for oxidative stress and inflammation-related diseases via biological integration of natural polyphenols and small-molecule drugs.

Study on synergistic mechanism of molybdenum disulfide/sodium carboxymethyl cellulose composite nanofiber mats for photothermal/photodynamic antibacterial treatment

Innovative antibacterial therapies using nanomaterials, such as photothermal (PTT) and photodynamic (PDT) treatments, have been developed for treating wound infections. However, creating secure wound dressings with these therapies faces challenges. The primary focus of this study is to prepare an antibacterial nanofiber dressing that effectively incorporates stable loads of functional nanoparticles and demonstrates an efficient synergistic effect between PTT and PDT. Herein, a composite nanofiber mat was fabricated, integrating spherical molybdenum disulfide (MoS2) nanoparticles. MoS2 was deposited onto polylactic acid (PLA) nanofiber mats using vacuum filtration, which was further stabilized by sodium carboxymethyl cellulose (CMC) adhesion and glutaraldehyde (GA) cross-linking. The composite nanofibers demonstrated synergistic antibacterial effects under NIR light irradiation, and the underlying mechanism was explored. They induce bacterial membrane permeability, protein leakage, and intracellular reactive oxygen species (ROS) elevation, ultimately leading to >95 % antibacterial activity against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), which is higher than that of single thermotherapy (almost no antibacterial activity) or ROS therapy (about 80 %). In addition, the composite nanofiber mats exhibited promotion effects on infected wound healing in vivo. This study demonstrates the great prospects of composite nanofiber dressings in clinical treatment of bacterial-infected wounds.

A Systematic Approach toward Enabling Maximal Targeting Efficiency of Cell Surface Proteins with Actively Targeted SERS Nanoparticles.

With their intricate design, nanoparticles (NPs) have become indispensable tools in the quest for precise cellular targeting. Among various NPs, gold NPs stand out with unique features such as chemical stability, biocompatibility, adjustable shape, and size-dependent optical properties, making them particularly promising for molecular detection by leveraging the surface-enhanced Raman scattering (SERS) effect. Their multiplexing abilities for the simultaneous identification of multiple biomarkers are important in the rapidly evolving landscape of diverse cellular phenotypes and biomolecular profiling. However, the challenge is ensuring that SERS NPs can effectively target specific cells and biomarkers among intricate cell types and biomolecules with high specificity. In this study, we improve the functionalization of SERS NPs, optimizing their targeting efficiency in cellular applications for ca. 160 nm NP-based probes. Spherical SERS NPs, conjugated with antibodies targeting epidermal growth factor receptor and human epidermal growth factor receptor 2, were incubated with cells overexpressing these proteins, and their specific binding potential was quantified at each stage by using flow cytometry to achieve optimal targeting efficiency. We determined that maintaining an average of 3.5 × 105 thiols per NP, 300 antibodies per NP, 18,000 NPs per cell, conducting a 15 min staining incubation at 4 °C in a shaker, and using SM(PEG)12 as a cross-linker for the NP conjugation were crucial to achieve the highest targeting efficiency. Fluorescence and Raman imaging were used with these parameters to observe the maximum ability of these NPs to efficiently target suspended cells. These highly sensitive contrast agents demonstrate their pivotal role in effective active targeting, making them invaluable for multiplexing applications across diverse biological environments.

Integrated preparation of functional lignin nanoparticles and levulinic acid directly from the pre-hydrolysis liquor of poplar wood

The pre-hydrolysis liquor (PHL) produced during pulp dissolution and biomass refining is mainly composed of hemicellulose and lignin, and it is a potential source for production of value-added materials and platform chemicals; however, their utilization has been a serious challenge. In this study, we proposed a green and simple strategy to simultaneously prepare size-controlled functional lignin nanoparticles (LNPs) and levulinic acid (LA) from PHL as the raw material. The as-prepared LNPs exhibited remarkable stability thanks to the presence of saccharides with abundant oxygen-containing groups and surface charges, which prevented aggregation and maintained long-term storage stability. Trace amounts of the LNPs (≤ 0.2 wt%) could stabilize various Pickering emulsions, even with oil-to-water ratios as high as 5:5 (v/v). Subsequently, the remaining PHL was directly used to produce LA without adding a catalyst; under optimal conditions (160 °C and 1 h), the yield of LA was 56.3 % based on the dry saccharide content in the raw PHL. More importantly, p-toluenesulfonic acid (p-TsOH), the only reactive reagent used during the entire preparation process, including the two preparation steps of the LNPs and LA, was reusable, and the recovery rate was >70 % after five cycles. Overall, this green and simple strategy effectively and comprehensively utilized the PHL and showed potential for producing biobased nanomaterials and platform chemicals.

Facile synthesis of Fe2O3, Fe2O3@CuO and WO3 nanoparticles: characterization, structure determination and evaluation of their biological activity

Due to their high specific surface area and its characteristic’s functionalized nanomaterials have great potential in medical applications specialty, as an anticancer. Herein, functional nanoparticles (NPs) based on iron oxide Fe2O3, iron oxide modified with copper oxide Fe2O3@CuO, and tungsten oxide WO3 were facile synthesized for biomedical applications. The obtained nanomaterials have nanocrystal sizes of 35.5 nm for Fe2O3, 7 nm for Fe2O3@CuO, and 25.5 nm for WO3. In addition to octahedral and square nanoplates for Fe2O3, and WO3; respectively. Results revealed that Fe2O3, Fe2O3@CuO, and WO3 NPs showed remarked anticancer effects versus a safe effect on normal cells through cytotoxicity test using MTT-assay. Notably, synthesized NPs e.g. our result demonstrated that Fe2O3@CuO exhibited the lowest IC50 value on the MCF-7 cancer cell line at about 8.876 µg/ml, compared to Fe2O3 was 12.87 µg/ml and WO3 was 9.211 µg/ml which indicate that the modification NPs Fe2O3@CuO gave the highest antiproliferative effect against breast cancer. However, these NPs showed a safe mode toward the Vero normal cell line, where IC50 were monitored as 40.24 µg/ml for Fe2O3, 21.13 µg/ml for Fe2O3@CuO, and 25.41 µg/ml for WO3 NPs. For further evidence. The antiviral activity using virucidal and viral adsorption mechanisms gave practiced effect by viral adsorption mechanism and prevented the virus from replicating inside the cells. Fe2O3@CuO and WO3 NPs showed a complete reduction in the viral load synergistic effect of combinations between the tested two materials copper oxide instead of iron oxide alone. Interestingly, the antimicrobial efficiency of Fe2O3@CuO NPs, Fe2O3NPs, and WO3NPs was evaluated using E. coli, S. aureus, and C. albicans pathogens. The widest microbial inhibition zone (ca. 38.45 mm) was observed with 250 mg/ml of WO3 NPs against E. coli, whereas using 40 mg/ml of Fe2O3@CuO NPS could form microbial inhibition zone ca. 32.86 mm against S. aureus. Nevertheless, C. albicans was relatively resistant to all examined NPs. The superior biomedical activities of these nanostructures might be due to their unique features and accepted evaluations.

Differential Silica Nanoparticles Functionalized with Branched Poly(1-Vinyl-1,2,4-Triazole): Antibacterial, Antifungal, and Cytotoxic Qualities

This research aims to improve antimicrobial materials based on functional silica nanoparticles. Three different methods were used in the study to create silica nanoparticles with other properties. The nanoparticles’ morphological structures are porous, hollow, and filled with spherical forms. The surface of these nanoparticles was grafted with poly(1-vinyl-1,2,4-triazole) (PVTri). The morphological properties of nanocomposites were used for analysis. In contrast, thermal gravimetric analysis was used to characterize the thermal properties of nanocomposites (thermogravimetric analysis). The silica nanoparticles were evaluated for their in vitro antimicrobial activity against Escherichia coli, Staphylococcus aureus, and Saccharomyces cerevisiae using minimum inhibitory concentration measurement. Silica nanoparticles have different antifungal and antibacterial properties related to their structure. The cytotoxic effects of the silica nanoparticles on HaCaT cells were performed with an MTS assay. In this study, we observed that high doses of HSS and e-SiO2 decreased cell growth, while HSS and e-SiO2 composite with PVTri increased cell proliferation.

Structural Control Enables Catalytic and Electrocatalytic Activity of Porous Tetrametallic Nanorods.

Integrating more than one type of metal into a nanoparticle that has a well-defined morphology and composition expands the functionalities of nanocatalysts. For a metal core/porous multimetallic shell nanoparticle, the availability of catalytically active surface sites and molecular mass transport can be enhanced, and the multielemental synergy can facilitate intraparticle charge transport. In this work, a reliable and robust synthesis of such a functional tetrametallic nanoparticle type is presented, where a micro- and mesoporous PdPtIr shell is grown on Au nanorods. The effect of critical synthesis parameters, namely temperature and the addition of HCl are investigated on the hydrodynamic size of the micellar pore template as well as on the stability of the metal chloride complexes and various elemental analysis techniques prove composition of the porous multimetallic shell. Due to the synergistic properties, the tetrametallic nanorods possess extensive negative surface charge making them a promising catalyst in reduction reactions. Dye degradation as well as the conversion of p-nitrophenol to p-aminophenol is catalyzed by the supportless nanorods without light illumination. By depositing the particles onto conductive substrates, the nanostructured electrodes show promising electrocatalytic activity in ethanol oxidation reaction. The nanocatalyst presents excellent morphological stability during all the catalytic test reactions.

Electrospinning of biopolymer nanofibers encapsulated with functional nanoparticles toward core‐shell fluorescence encoding

AbstractPhotochromism has been an efficient approach to improve authenticity of commercial products. In order to prepare an authentication nanofibrous film with mechanical reliability, it has been crucial to improve the engineering production route of the authentication materials. Herein, we electrospun photoluminescent nanofibrous film with a fiber diameter of 50–200 nm from the environmentally‐friendly polylactic acid embedded with nanoparticles of rare‐earth activated strontium aluminate (NRESA; 10–15 nm). The created nanocomposite film was colorless in daylight, and became an intense green in ultraviolet light. The strontium aluminate photochromic agent must be applied in the nanoparticle form to ensure film transparency by enhancing its dispersion without aggregation in the electrospun polylactic acid nanofiber bulk. An emission peak was observed at 518 nm after excitation of the pigment‐polylactic acid nanofibers at 365 nm. Raising NRESA ratio increased the hydrophobic properties of the pigment‐polylactic acid nanofibers without changing their visual or mechanical properties. The transparent films showed high photochromic reversibility without exhaustion under numerous exposure cycles of ultraviolet light and darkness. The nanofibrous mats were elastic and flexible. The current technique is an effective strategy for making a variety of anti‐counterfeiting substances.

Construction of a Functional Nucleic Acid-Based Artificial Vesicle-Encapsulated Composite Nanoparticle and Its Application in Retinoblastoma-Targeted Theranostics.

Retinoblastoma (RB) is an aggressive tumor of the infant retina. However, the ineffective targeting of its theranostic agents results in poor imaging and therapeutic efficacy, which makes it difficult to identify and treat RB at an early stage. In order to improve the imaging and therapeutic efficacy, we constructed an RB-targeted artificial vesicle composite nanoparticle. In this study, the MnO2 nanosponge (hMNs) was used as the core to absorb two fluorophore-modified DNAzymes to form the Dual/hMNs nanoparticle; after loaded with the artificial vesicle derived from human red blood cells, the RB-targeted DNA aptamers were modified on the surface, thus forming the Apt-EG@Dual/hMNs complex nanoparticle. The DNA aptamer endows this nanoparticle to target the nucleolin-overexpressed RB cell membrane specifically and enters cells via endocytosis. The nanoparticle could release fluorophore-modified DNAzymes and supplies Mn2+ as a DNAzyme cofactor and a magnetic resonance imaging (MRI) agent. Subsequently, the DNAzymes can target two different mRNAs, thereby realizing fluorescence/MR bimodal imaging and dual-gene therapy. This study is expected to provide a reliable and valuable basis for ocular tumor theranostics.

Miniaturized Biosensors Based on Lanthanide-Doped Upconversion Polymeric Nanofibers.

Electrospun nanofibers possess a large surface area and a three-dimensional porous network that makes them a perfect material for embedding functional nanoparticles for diverse applications. Herein, we report the trends in embedding upconversion nanoparticles (UCNPs) in polymeric nanofibers for making an advanced miniaturized (bio)analytical device. UCNPs have the benefits of several optical properties, like near-infrared excitation, anti-Stokes emission over a wide range from UV to NIR, narrow emission bands, an extended lifespan, and photostability. The luminescence of UCNPs can be regulated using different lanthanide elements and can be used for sensing and tracking physical processes in biological systems. We foresee that a UCNP-based nanofiber sensing platform will open opportunities in developing cost-effective, miniaturized, portable and user-friendly point-of-care sensing device for monitoring (bio)analytical processes. Major challenges in developing microfluidic (bio)analytical systems based on UCNPs@nanofibers have been reviewed and presented.

Nanoscopic oxygen control of functional oxide nanoparticles by electro-chemical route at ambient temperature

La0.67Ca0.33MnOδ nanoparticles of approximate size ∼ 4 nm have been prepared by the chemical solution deposition method to investigate effect of oxygen stoichiometry in the nanoparticles without changing their sizes. Electrochemical oxidation method has been used to change the oxygen stoichiometry δ\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\delta$$\\end{document} at room temperature, which unlike conventional methods to change oxygen stoichiometry by heating in controlled ambience, does not lead to any significant change in size. This has allowed us to investigate the effects of stoichiometry variations in the nanoparticles with no change in size. The unit cell volume, lattice constants and orthorhombic strains of the as prepared sample (with δ\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\delta$$\\end{document} = 2.74) are changed by incorporation of oxygen by electrochemical oxidation which in turns affects the magnetic properties. In addition, oxidation leads to change in oxygen stoichiometry of the magnetically “dead” surface layer on the nanoparticles which also affects their magnetization and coercive field.

Naphthalimide-based Functional Glycopolymeric Nanoparticles as Fluorescent Probes for Selective Imaging of Tumor Cells.

A series of functional glycopolymer nanoparticles with 1,8-naphthalimide motif was designed, synthesized and applied for tumor cell imaging. With the pH-sensitive and aggregation-induced emission (AIE) effect of the 1,8-naphthalimide fluorescent probe, the presence of glucose-based glycopolymers enhanced its water-solubility and biocompatibility. Owing to the dual tumor-targeting effects of the dense glucose part and the boronic ester modification, the obtained glycopolymers showed high affinity to tumor cells, with a much faster staining rate than normal cells, indicating a great potential for diagnosis and treatments of cancers.

Encapsulation of Inorganic Nanoparticles by Anionic Emulsion Polymerization of Diethyl Methylene Malonate for Developing Hybrid Microparticles with Tailorable Composition

Colloidal particle self-assembly into higher-ordered structures has been of great interest due to the promise of creating metamaterials with novel macroscopic properties. The physicochemical properties of these metamaterials can be tailored to achieve composites with tunable functionalities, either by controlling the assembly morphology and/or chemistry of the colloidal building blocks. This work describes a strategy of developing microparticles with a hybrid configuration that have an inorganic and an organic part. The inorganic part comprises functional nanoparticles, which are embedded within an organic polymer particle composed of diethyl methylene malonate polymer [p(DEMM)] prepared using anionic emulsion polymerization. DEMM polymerization is initiated entirely by the presence of hydroxyl anions and the resulting particle diameter can be tuned between 300 nm and 1 micrometer by reaction pH. Inorganic nanoparticles with varying chemistry (TiO2, CdTe, ZnO) can be loaded into the p(DEMM) particle with a controlled weight fraction, as confirmed by thermogravimetric analysis. The colloidal stability of the composite microparticles is seen to be dependent on the ligand coating attached to the inorganic constituent. These results provide a synthetic groundwork for creating hybrid, stimuli-responsive microparticles.

Micromachined capacitance-sensitive device with immobilized functional ZnO nanoparticles detecting glucose and uric acid

Micromachined capacitance-sensitive device with immobilized functional ZnO nanoparticles detecting glucose and uric acid

Fabrication of Yolk-Shell Structure with Multifarious Nanoparticles via Double-Layered Encapsulation Strategy.

The post-encapsulation method (such as single-layered encapsulation) is a promising strategy to synthesize yolk-shell structures that protect functional nanoparticles by the molecular sieving effect. However, this method exhibited limited loading capacity and nonuniform encapsulation during the co-encapsulation of various nanoparticles owing to the insufficient surface area for nanoparticle attachment. To address these limitations, we proposed a double-layered encapsulation method comprising an increased number of silica template layers and separate attachment of multifarious nanoparticles to different layers. Compared with conventional methods, this strategy can precisely adjust the ratio of encapsulated nanoparticles and increase the loading amount, which improves the functionality of yolk-shell structures, such as the photothermal properties of gold nanoparticle-encapsulated yolk-shell structures (∼69%). We describe, for the first time, the precise control of the ratio of encapsulated nanoparticles and the loading of numerous nanoparticles. Consequently, this strategy has significant potential for various applications of yolk-shell structures.

Advances in functional lipid nanoparticles: from drug delivery platforms to clinical applications.

Since Doxil's first clinical approval in 1995, lipid nanoparticles have garnered great interest and shown exceptional therapeutic efficacy. It is clear from the licensure of two RNA treatments and the mRNA-COVID-19 vaccination that lipid nanoparticles have immense potential for delivering nucleic acids. The review begins with a list of lipid nanoparticle types, such as liposomes and solid lipid nanoparticles. Then it moves on to the earliest lipid nanoparticle forms, outlining how lipid is used in a variety of industries and how it is used as a versatile nanocarrier platform. Lipid nanoparticles must then be functionally modified. Various approaches have been proposed for the synthesis of lipid nanoparticles, such as High-Pressure Homogenization (HPH), microemulsion methods, solvent-based emulsification techniques, solvent injection, phase reversal, and membrane contractors. High-pressure homogenization is the most commonly used method. All of the methods listed above follow four basic steps, as depicted in the flowchart below. Out of these four steps, the process of dispersing lipids in an aqueous medium to produce liposomes is the most unpredictable step. A short outline of the characterization of lipid nanoparticles follows discussions of applications for the trapping and transporting of various small molecules. It highlights the use of rapamycin-coated lipid nanoparticles in glioblastoma and how lipid nanoparticles function as a conjugator in the delivery of anticancer-targeting nucleic acids. High biocompatibility, ease of production, scalability, non-toxicity, and tailored distribution are just a meager of the enticing allowances of using lipid nanoparticles as drug delivery vehicles. Due to the present constraints in drug delivery, more research is required to utterly realize the potential of lipid nanoparticles for possible clinical and therapeutic purposes.

Proton-Assisted Assembly of Colloidal Nanoparticles into Wafer-Scale Monolayers in Seconds.

Underwater adhesion processes in nature promise controllable assembly of functional nanoparticles for industrial mass production; However, their artificial strategies have faced challenges to uniformly transfer nanoparticles into a monolayer, particularly those below 100nm in size, over large areas. Here a scalable "one-shot" self-limiting nanoparticle transfer technique is presented, enabling the efficient transport of nanoparticles from water in microscopic volumes to an entire 2-inch wafer in a remarkably short time of 10 seconds to reach near-maximal surface coverage (≈40%) in a 2D mono-layered fashion. Employing proton engineering in electrostatic assembly accelerates the diffusion of nanoparticles (over 50 µm2/s), resulting in a hundredfold faster coating speed than the previously reported results in the literature. This charge-sensitive process further enables "pick-and-place" nanoparticle patterning at the wafer scale, with large flexibility in surface materials, including flexible metal oxides and 3D-printed polymers. As a result, the fabrication of wafer-scale disordered plasmonic metasurfaces in seconds is successfully demonstrated. These metasurfaces exhibit consistent resonating colors across diverse material and geometrical platforms, showcasing their potential for applications in full-color painting and optical encryption devices.

Enhancing Efficiency in Inverted Quantum Dot Light-Emitting Diodes through Arginine-Modified ZnO Nanoparticle Electron Injection Layer

Many quantum dot light-emitting diodes (QLEDs) utilize ZnO nanoparticles (NPs) as an electron injection layer (EIL). However, the use of the ZnO NP EIL material often results in a charge imbalance within the quantum dot (QD) emitting layer (EML) and exciton quenching at the interface of the QD EML and ZnO NP EIL. To overcome these challenges, we introduced an arginine (Arg) interlayer (IL) onto the ZnO NP EIL. The Arg IL elevated the work function of ZnO NPs, thereby suppressing electron injection into the QD, leading to an improved charge balance within the QDs. Additionally, the inherent insulating nature of the Arg IL prevented direct contact between QDs and ZnO NPs, reducing exciton quenching and consequently improving device efficiency. An inverted QLED (IQLED) utilizing a 20 nm-thick Arg IL on the ZnO NP EIL exhibited a 2.22-fold increase in current efficiency and a 2.28-fold increase in external quantum efficiency (EQE) compared to an IQLED without an IL. Likewise, the IQLED with a 20 nm-thick Arg IL on the ZnO NP EIL demonstrated a 1.34-fold improvement in current efficiency and a 1.36-fold increase in EQE compared to the IQLED with a 5 nm-thick polyethylenimine IL on ZnO NPs.