Frequency Selective Surface Research Articles

Optically Transparent Frequency Selective Surfaces with Wideband Capability for IoT Applications: A Polarization-Independent Double-Layer Design.

This study proposes wide-band frequency selective surfaces (FSS) with polarization-independent characteristics that are tailored for IoT applications. The design consists of two different layers with band-stop characteristics that target key frequency bands in sub-6 GHz: 3.7 GHz (n77) and 4.5 GHz (n79), offering a 1.39 GHz bandwidth spanning from 3.61 GHz to 5.0 GHz. This study also presents a double-layer structure with a WB property with a fractional bandwidth of 32%. Simulations have been conducted to observe variations in insertion loss across incident and polarization angles ranging from 0 to 60 degrees for both TE and TM modes in the suggested FSS structures. These simulations demonstrate the design's polarization independence. Transparent polyvinyl chloride with a dielectric constant of 2.77 and a thickness of 1.48 mm has been utilized as the substrate material. The optical transmittance is calculated to be 96.7% for Layer 1, 95.7% for Layer 2, and 92.4% for the double-layer structure, and these calculated optical transmittance values were found to be higher compared to the studies in the literature. The proposed design is well-suited for sub-6 GHz IoT applications due to their high transparency, cost-effectiveness, robust high-performance capabilities in suppression, and polarization-independent features. The results of 3D full-wave simulations were compared with measurement and the equivalent circuit model outcomes, and a good agreement between the results was observed.

A low profile high gain concave conformal ring cylindrical dielectric resonator antenna loaded with split ring resonator for ISM and C band applications

SummaryA low profile, concave conformal ring cylindrical dielectric resonator antenna (CDRA) employing frequency selective surface (FSS) using split ring resonator (SRR) for wideband and high gain applications is presented. The ring CDRA loaded with the monopole is designed to excite the TM01δ mode to increase the antenna's bandwidth. The effect of a curved ground plane (GP) on the radiation performance of CDRA is studied. A 5 × 5 array of the SRR is placed above the conformal GP at a far‐field distance optimized to (2n ± 1) λ/4 from the radiating element to enhance the gain of the proposed structure. The planar CDRA with FSS is compared with the conformal CDRA with FSS and a 4.3 GHz improvement in bandwidth is observed due to the multiple reflection and surface reflection leading to a 3.2 dBi improvement in gain. An impedance bandwidth of 51.8% (5 to 8.5 GHz) with a maximum gain of 8.7 dBi at 7.3 GHz resonant frequency and 99% radiation efficiency at 5.9 GHz is offered by the proposed antenna with FSS. Additionally, the proposed CDRA has a low profile of 0.12 λ0 where λ0 is the lower cut‐off frequency's wavelength. A good agreement is observed between the simulated and measured results.

Metasurface loaded dual band antenna for high gain on- and off- body communication

Metasurfaces are specially made materials designed to have unique properties not found in nature. They are categorized into different types, such as artificial magnetic conductor (AMC), partial reflecting surfaces (PRS), and frequency selective surfaces (FSS). Among these, FSS is commonly used in today’s technology to improve antenna performance, especially in boosting signal strength by blocking unwanted radiation. Recent research is focused on creating FSS-based antennas for Ultra-wideband (UWB) or single band applications, with a significant emphasis on enhancing signal strength. Unlike traditional methods, this study concentrates on designing antennas that are both simple in shape and offers broader frequency coverage, specifically for 2.45 GHz and 5.8 GHz applications. To enhance antenna performance, a dual-band FSS is employed, optimizing the system for improved operation at both resonating frequencies. This results in a high-gain antenna system, which is further investigated for body area network (BAN) systems, considering the crucial performance metric of specific absorption rate (SAR). The findings are compared with recently reported FSS-based antennas to underscore their scientific contribution and potential for high gain, low SAR applications within the 2.45 GHz and 5.8 GHz frequency bands.

Second order frequency selective surface design multi-functional at two bands

This paper proposes an active frequency selective surface which furnishes three bands of higher order filtering characteristics. It controls multi-functional features, at two bands (centered at 2 GHz and 4 GHz), namely electromagnetic response and polarization of plane wave. Nine discrete filtering outputs are independently controlled through switching in bias supply to four PIN diodes embedded in two layers of AFSS unit cell. Two multifunctional bands hold stability upto 45° angles under all polarizations of wave. Passive band at around 5.9 GHz contributed by all the independent binary combinations exhibits stability upto 45° angles of TE wave only. The equivalent circuit method is used to explain and verify the designed structure. Finally, the AFSS structure is fabricated and reliability of the simulation results is verified through experiments.

Tunable liquid crystal double-layer frequency selective surface with wide transmission band and small insertion loss

ABSTRACT In this paper, a tunable Frequency Selective Surface (FSS) based on liquid crystal (LC) with a wide transmission band, large tuning range, high tuning rate, and miniaturization is designed. First, a single-layer FSS is developed with two frequency selective layers and one LC tunable layer. The simulation and experiment results show that the single-layer FSS has a transmission bandwidth greater than 4.25 GHz, and the LC change can make the center frequency of the transmitted band shift to the lower frequency by 576 MHz, with a tuning rate of 4.2%. Subsequently, a double-layer FSS is designed by adding a coupling layer to the single-layer FSS, achieving a flat-top passband and enhancing the tuning rate. Simulation and experimental validation show that altering the LC state enables continuous tuning of the center frequency of the double-layer FSS from 14.95 GHz to 13.86 GHz, with a tuning rate of 7.2%. This structure exhibits a flat-top passband wider than 5.7 GHz, a relative bandwidth of 41%, and a rectangular coefficient below 1.877. Moreover, the double-layer FSS demonstrates favorable polarization stabilization and wide incidence angle stabilisation properties in various states.

Band-Stop Frequency-Selective Surface (FSS) with Elliptic Response Designed by the Extracted Pole Technique.

This paper describes and validates an advanced synthesis design process of Frequency-Selective Surfaces (FSSs) with elliptic band-stop responses. A systematic procedure based on the Generalized Chebyshev Function and the extracted pole technique enables control of the position of the transmission zeros and the attenuation level to obtain an equiripple rejection response. A systematic process is followed to obtain the lumped LC values of the resonator circuits extracted as poles and the impedance inverters. Then, equivalent dipoles and transmission lines are obtained to carry out the electromagnetic design at normal incidence for a linearly polarized field. The impact of the higher-order modes of the periodic structure on the electrical response of the FSS, which can be relevant due to the stringent selected specifications, has been also analyzed. A fourth-order band-stop filter with a 3 GHz bandwidth centered at 30 GHz and its attenuation at 50 dB has been designed considering three different implementations: two filters using a vacuum as a transmission line with different connection lengths and a third one using a dielectric substrate to enable its manufacturing. In order to verify the design procedure using experimental results, the third filter with printed dipoles in the dielectric substrate has been manufactured and measured, thus validating the developed process.

A high Q factor sensor to measure the complex permittivity and effective permittivity based on a band stop frequency-selective surface

In this paper, a metamaterial sensor is proposed based on a band stop frequency-selective surface (FSS) with high Q factor of 421.9 at 8.032 GHz. The sensor consists of a square loop FSS and a F4B dielectric substrate. This is the first sensor based on a band stop FSS sensing the effective permittivity of 3D printed hollow structures. The equivalent circuit method is used to analyze the characteristics of the sensor, and the results agree well. Two materials under test and four different hole radii of 3D printed hollow structures are used to verify the sensing function. At the same time, the effective permittivity of the 3D printed hollow structure is analyzed, and the correctness of the effectiveness is verified by simulation inversion and Maxwell-Garnett formula. The sensor has the advantages of high Q factor, wide incidence angle and polarization angle insensitivity, which can provide some guidance in metamaterials sensing.

Reducing out-of-band radar cross-section of metasurface-based radome composites via beam-scattering mechanism

In this work, a metasurface-based radome composite (MRC) with customized electromagnetic (EM) functions is proposed. By employing a beam-scattering mechanism, high transmission at 2–4 GHz and significant radar cross-section (RCS) reduction at 8–18 GHz are achieved. The MRC prototype features a sandwiched construction and is fabricated using quartz fiber-reinforced composite (QFRC) skins, polymethacrylimide (PMI) foam cores, and silver-based frequency selective surface (FSS) screens. The calculation, simulation, and measured results demonstrated that the transmission of the planar specimen is larger than −1 dB at 2–4 GHz and the RCS reduction is less than −10 dB at 8–18 GHz. The measured results also verified that in the HH and VV polarizations, the mono-static RCS of a square pyramid (SP) specimen at specific directions from 8 GHz to 12 GHz is significantly reduced. It is believed that our finding has great application potential in stealth radome technology.

Preparation and electromagnetic absorption properties of silver-decorated polystyrene with frequency-selective surfaces

Preparation and electromagnetic absorption properties of silver-decorated polystyrene with frequency-selective surfaces

A Novel Compact GNSS Antenna with Plasma Frequency Selective Surface

In this study, a plasma frequency selective surface (PFSS) was designed with an array of ordinary fluorescent lamps backed by a conducting plate. The proposed PFSS structure was used as a reflector with the spiral two arms Archimedean type Global Navigation Satellite System (GNSS) antenna to reduce the overall size of the antenna system. Characteristics and the performance of the proposed system were presented by using the results of simulations and experiments in the GNSS band. The optimum distance between antenna and PFSS was found to be around 35 mm to achieve a maximum gain in the simulation which is a lower profile than antenna with conventional conductive plate (66 mm at the GNSS center frequency). Experimental results show that the antenna system has mean values of around 6.7 dBiC gain, 1.27 dB axial ratio and less than -10 dB return loss in the range of 1.14 and 1.61 GHz. All these results show that the proposed novel antenna system is suitable for the reception of the GNSS signals with the advantage of its low profile design.

Ultra-wideband absorber based on multilayer lossy frequency selective surface

In this letter, a multilayer dielectric with a lossy frequency-selective surface (FSS) absorber is proposed, which is composed of three layers of resistive film-dielectric composite layer and a metal grounded plane. Particularly, each resistive film-dielectric composite layer consists of a polyethylene terephthalate (PET), polymethacrylimide foam (PMI), and resistive film layer. An equivalent circuit model is established to further understand the performance of the absorber based on the impedance matching approach and the transmission line theory. Experimental results reveal that the metamaterial absorber (MMA) covers -10 dB bandwidth of 1.96-21.8 GHz for normal incidence. Meanwhile, the absorption rate can retain more than 80% for both TE and TM polarizations within 55° incidence angles. Furthermore, the fractional bandwidth of the MMA is 167% and its thickness is only 0.108 ?L. The MMA has the characteristics of ultra-wideband, high absorption rate, and polarization stability, making it suitable for communication systems.

Design of single layer bowtie wide band-stop frequency selective surface with angular stability for C-band applications

This paper presents the design and analysis of a single-layer wide band-stop frequency selective surface (FSS) tailored for C-band applications. The proposed FSS design employs a modified bow-tie unit cell structure that enhances band stop characteristics, resulting in improved performance compared to traditional FSS geometry. The design process involves numerical simulations and optimization techniques to achieve the desired frequency response. A modified bowtie element with FR4 substrate comprises the proposed FSS which exhibits a resonant frequency of 6.0 GHz with a wide bandwidth of 4.84–6.96 GHz (35.93 %) and act as a band stop filter. The FSS is analyzed in terms of its transmission coefficients, providing insight into its filtering properties. In addition, parametric studies of the unit cells are done. Furthermore, the angular stability of the proposed FSS is simulated with incident waves at various angles between 0° to 60° for both TE and TM modes. The proposed FSS presents C-band applications of WLAN, ISM/WiMAX, satellite communications, radar systems, shielding and communication devices, also enhancing filtering capabilities and system performance. The simulation results are well correlated with measurement results.

Combined scheme for mitigating coupling interference in dual‐band shared‐aperture base station antenna

AbstractA dual‐band shared‐aperture antenna array is presented, involving a combined scheme to suppress mutual coupling interference. The proposed array is comprised of a low‐band (LB) antenna, a frequency selective surface (FSS), sixteen high‐band (HB) antennas, and a reflector. The LB antenna utilises electromagnetic transparent (ET) characteristics to minimise scattering interference, while the FSS isolates resonance interference and port signal interference. The combined scheme integrates the benefits of both the ET antenna and FSS to suppress mutual coupling interference effectively. A prototype of the proposed antenna was fabricated and measured, operating at 1.7–2.7 GHz and 3.3–3.9 GHz. The simulated and measured results demonstrate stable patterns for both the LB antenna and the HB antennas. The cross‐band isolation is higher than 28 dB in the low‐band. With these advantages, the antenna array is suitable for base station applications.

Frequency selective surface with quad-band absorption/transmission and angular stability for TE and TM polarizations

The proposed FSS structure employs two square annular rings for absorption functionalities and two square aperture slots for transmission properties. Through comprehensive simulations and analysis, the FSS structure demonstrates remarkable performance in selectively absorbing and transmitting electromagnetic waves across four distinct frequency bands. Moreover, the design exhibits excellent TE and TM polarizations angular stability, consistently maintaining constant absorption and transmission characteristics across varying incidence angles. A comprehensive analysis of the equivalent circuit model of the FSS structure has also been performed to understand the quad-band transmission and absorption properties. The measurement results underscore the effectiveness of the design of a 250*250 mm array, with absorption peaks notably occurring at 4.2 GHz and 7.23 GHz, boasting peak absorption rates of 92% and 85%, respectively. Moreover, the insertion loss within the pass band at 8.8 GHz and 12.2 GHz stands impressively low at 0.2 dB and 0.32 dB, respectively. Notably, the proposed quad-band FSS showcases polarization-insensitive behavior across a range from 0° to 60° and successfully undergoes conformal testing with a curvature radius up to 50 mm. The results of experimental testing on a quad-band FSS prototype demonstrate superior agreement with those obtained through simulations and analytically derived equivalent circuit model (ECM) results, validating its practical applicability in real-world scenarios.

Metasurface loaded dual port circularly polarized dielectric resonator antenna with reduced RADAR cross section and mutual coupling features

The design of dual port radiator with a polarization diversity technique and reduced radar cross section (RCS) is described in this study. Cross slot is used to stimulate cylindrical ceramic for generating circular polarization features. Mirror orientation of aperture between port-1 and port-2 improves the isolation level by 25 dB. To suppress the antenna’s monostatic RCS, split ring resonator (SRR) based frequency selective surface is positioned between and around the dual ports. Experimental outcomes confirm the designed radiator operates from 4.11–5.24 GHz along with 3-dB axial ratio in between 4.15–4.92 GHz. The value of monostatic RCS is reduced by 15 dBsm in between the operating band. Broadsided radiation characteristics and good value of diversity parameter makes the designed radiator applicable for C-band Radar applications.

A Fifth-Order X-Band Frequency-Selective Surface With High Selectivity and Angular Stability Based on 3-D Coupling Slot

A Fifth-Order X-Band Frequency-Selective Surface With High Selectivity and Angular Stability Based on 3-D Coupling Slot

Ultra Miniaturization and Transparency Frequency Selective Surface for Dual Band ISM Shielding

This article presents an ultraminiaturized frequency selective surface (FSS) for shielding 2.4 GHz and 5.8 GHz (ISM) signals. The unit cell size is 0.056λ × 0.056λ (λ is the free space wavelength at the first resonant frequency). It has smaller cell size and good transparency compared to previous ISM band studies, and transparency at 54%. The proposed FSS design consists of a wall structure and a compound square loop with 2.4 GHz and 5.8 GHz resonance frequencies for ISM band coverage. This FSS structure was fabricated on float glass with a dielectric constant of 8 by a photolithographic process. The fabricated FSS structure has excellent angular stability and polarization stability, which is further verified by experimentation. An easy optimization method is proposed to tune the independent resonant frequencies by optimizing the geometries individually. This FSS is interpreted by filtering through surface induced currents and equivalent circuit models. A prototype of the proposed FSS is fabricated and measured. The simulation results are in good agreement with the measured results. The proposed FSS has polarization insensitivity and 80∘ angle stability and is suitable for solving the EMI problem in ISM band.

Wide‐angle band‐pass FSS with high‐frequency selectivity based on SIW cavity technology

AbstractThis work proposes and investigates a wide‐angle band‐pass frequency selective surface (FSS) with two sharp sidebands. The presented FSS element is made up of three metallic layers and two substrate layers in between, which are surrounded by a substrate‐integrated waveguide (SIW) cavity. The top metallic layer is identical to the bottom layer, composed of a square patch etched with a hexagonal groove, while the middle layer is a similar patch but with rectangular notch edges. This structure achieves a second‐order band‐pass response with highly frequency selectivity on either side of the passband. At the same time, this FSS demonstrates excellent stability for both transverse electric and transverse magnetic polarizations with incident angles between 0° and 60°. The electric current and field distributions are demonstrated for deep analysis. Furthermore, an equivalent circuit model is developed to further understand the operating mechanisms. To verify the validity of the design, we construct a prototype of the SIW‐based FSS (SIW‐FSS) and measured it. There is a fair degree of agreement between the measured and simulated results. Finally, we loaded it onto the horn antenna and tested its application in filtering antennas.

A Low-profile Dual-band Frequency Selective Surface with High Selectivity at its Higher Passband

In order to meet the requirements for multiband communication, a dual-band passband frequency selective surface (FSS) with low-profile and high selectivity at its higher passband is proposed in this paper. The proposed FSS is a three-layer structure. An arc-cross patch (ACP) and four quarter-circular patches (QCP) are introduced on the outer layers to produce two transmission nulls of the higher passband, which result in high selectivity of higher passband. The inductively complementary structure on the middle layer is introduced to manipulate the coupling between layers which contribute to the low-profile and angular stability. The segmental study method is used to establish the equivalent circuit model (ECM) and analyze its mechanism. The proposed dual-band FSS, whose high selectivity was verified by experiment, is low-profile and shows good polarization insensitivity and angular stability. A feasible FSS design solution is provided for dual-band communication.

Stacked dual‐band antenna with flexible combination structure based on frequency selective surface

Stacked dual‐band antenna with flexible combination structure based on frequency selective surface