Fracture Load Research Articles

Behavior of ultra-high-performance concrete deep beams reinforced by basalt fibers

Abstract Deep beams are crucial for construction projects due to their load-carrying capacity, shear resistance, and architectural adaptability. Ultra-high strength concrete and ultra-high-performance concrete (UHPC) are used in their production. Basalt fiber is used as an alternative due to its corrosion resistance, tensile strength, and thermal stability. This study investigates the behavior of UHPC deep beams reinforced with basalt fibers. Three sets of 11 specimens were constructed without transverse reinforcement and reinforced with either fibers or steel fibers. The study also analyzes the impact of parameters like shear strength capacity, crack development, and load-deflection behavior on UHPC deep beams. The study discovered that the inclusion of basalt fibers in UHPC deep beam can effectively postpone the onset of diagonal cracks. Incorporating basalt fiber at concentrations of 0.5, 0.75, and 1.0% led to respective increases of 48.17, 70.07, and 86.66% in the diagonal fracture force, as compared to the inclusion of steel fibers which resulted in increases of 18.24, 56.93, and 98.54% in diagonal fracture loads. The ideal ratio for enhancing the maximum shear capacity was found to be 0.75% of basalt. This specific percent resulted in the highest measured force out of the three percentages that were examined. The addition of basalt fibers at concentrations of 0.5, 0.75, and 1.0% resulted in respective improvements of 11.62, 30.08, and 28.69% in the ultimate shear capacities. During that period, steel fibers significantly enhanced the ultimate shear capacity, resulting in an increase of 19.83, 34.49, and 55.24% compared to specimens without fiber reinforcement. Regarding the second parameter of this investigation, a drop in the shear span ratio is linked to an augmentation in shear capacity and a reduction in mid-span deflection to varying extents for both the utilization of basalt and steel fibers.

In Vitro Analysis of Bonding and Wear Properties of 3D Printed Denture Tooth Materials.

While additive manufacturing (3D printing) has recently enhanced removable prosthodontics, the properties of new 3D printed materials are not well understood. This study aims to elucidate the physical properties of these materials, focusing on bonding to a 3D printed denture base material and wear resistance. For denture tooth-denture base bonding analyses, the same denture tooth material (Premium Teeth, Formlabs) was used with three denture base-bonding group assignments (n=6 each group) bonded using three protocols: Group A1 was bonded with Lucitone Digital Print-3D Denture Base using the Lucitone Fuse System (Dentsply), Group A2 with Formlabs Denture Base using the Formlabs Denture Base Bonding System, and Group A3 with Formlabs Denture Base using the Ivoclar Ivotion Bonding System (Ivoclar). Specimens were made according to the ISO-TS-19736-2027 standard. A 3D printed tooth mimicking a central incisor was bonded to the denture base and subjected to a palatal load at the incisal region at 90° from the long axis of the tooth until failure. The fracture surface was examined at 10× magnification. ANOVA with α=0.05 was used to determine statistically significant differences. For wear analysis, the same denture base material and bonding system (Lucitone Digital Print-3D Denture Base/Lucitone Fuse System, Dentsply) was used with four denture tooth material group assignments (n=8 each group): Group B1 used Formlabs Premium Teeth, Group B2 used SprintRay High Impact Denture Teeth, Group B3 used Lucitone Digital IPN Premium Tooth, and Group B4 used Ivotion Polymethyl Methacrylate (PMMA) Milled Teeth (Ivoclar). A premolar denture tooth bonded with the denture base was subjected to a chewing simulation cyclic loading of 1,200,000 cycles. Sample failures, vertical wear, and volume loss were documented. ANOVA with α=0.05 was used to determine statistically significant differences. The fracture load to failure values for A1, A2, and A3 were 175±106 N, 167±46.3 N, and 183±48.9 N, respectively (p=0.95). Most failure characteristics were mixed, except one of A2 was cohesive and half of A3 was cohesive. For cyclic loading, B4 was the only group where all specimens failed within 1,200,000 cycles, while B1, B2, and B3 had four, three, and five sample failures, respectively. Vertical wear was 0.93±0.34 mm, 1.22±0.37 mm, 1.05±0.27 mm, and 0.37±0.02 mm for B1, B2, B3, and B4, respectively (p<0.01). Abrasion volumes were 9.5±3.7 mm³, 12.2±4.7 mm³, 10.6±3.5 mm³, and 2.2±1.3 mm³ for B1, B2, B3, and B4, respectively. Vertical height loss per chewing cycle (μm/cycle) was 0.0022±0.0019, 0.0030±0.0029, 0.0012±0.00005, and 0.0080±0.0050 for B1, B2, B3, and B4, respectively (p<0.01). Abrasion volume per chewing cycle (μm³/cycle) was 17650.8±9682.9, 27263.4±24746.8, 11836.5±4200.8, and 70436.8±73602.5 for B1, B2, B3, and B4, respectively (p=0.02). The bonding strength and wear resistance of 3D printed denture materials vary by manufacturer. Formlabs Denture Base with Ivoclar Ivotion showed the highest fracture load, indicating superior bonding strength. In wear analysis, Ivoclar Ivotion PMMA Milled Teeth exhibited the least vertical wear and abrasion volume but had the highest failure rate under cyclic loading. While printed denture materials excel in bonding strength, their wear resistance may not be as good as milled denture teeth, highlighting the need to balance these properties in clinical applications.

A simple, fast, and robust criterion for predicting fracture load and crack growth path in notched elastoplastic plates under mixed-mode loading

This study assesses the combined in-plane tensile/shear failure of aluminum plates containing notches. With this aim, a numerical method, i.e., the so-called equivalent material concept (EMC) in association with the extended finite element method (XFEM), is introduced to simulate the fracture phenomenon. The predicted failure load, initiation angle, and growth path are compared to experimental results reported for aluminum alloys in the literature to evaluate the functionality of the proposed method. Also, the accuracy of the EMC-XFEM model was compared to the conventional Ductile Damage method. The EMC-XFEM combined model is found to be fast and robust with appropriate accuracy in fracture predictions of ductile samples in comparison with the elastoplastic damage model and experimental data.

Experimental Study on Fracture Toughness of Shale Based on Three-Point Bending Semi-Circular Disk Samples

A large number of construction practice projects have found that there are many joints and microcracks in rock, concrete, and other structures, which cause the complexity of rock mechanical properties and are the main cause of geological or engineering disasters such as earthquakes, landslides, and rock bursts. To establish a rock fracture toughness evaluation method and understand the distribution range of fracture toughness of Longmaxi Formation shale, this study prepared three-point bending semi-circular disk shale samples of Longmaxi Formation with different crack inclination angles. The dimensionless fracture parameters of the samples, including the dimensionless stress intensity factors of type I, type II, and T-stress, were calibrated using the finite element method. Then, the peak load of the samples was tested using quasi-static loading, and the load–displacement curve characteristics of Longmaxi Formation shale and the variation in fracture toughness with crack inclination angle were analyzed. The study concluded that the specimens exhibited significant brittle failure characteristics and that the stress intensity factor is not the sole parameter controlling crack propagation in rock materials. With an increase in crack inclination angle, the prefabricated crack propagation gradually transitions from being dominated by type I fracture to type II fracture, and the T-stress changes from negative to positive, gradually increasing its influence on the fracture. An excessively large relative crack length increases the error in fracture toughness test results. Therefore, this paper suggests that the relative crack length a/R should be between 0.2 and 0.6. The fracture load distribution range of shale samples with different crack angles is 3.27 kN to 10.92 kN. As the crack inclination angle increases, the maximum load that the semi-circular disk shale samples can bear gradually increases. The pure type I fracture toughness of Longmaxi Formation shale is 1.13–1.38 MPa·m1/2, the pure type II fracture toughness is 0.55–0.62 MPa·m1/2, and the T-stress variation range of shale samples with different inclination angles is −0.49–9.48 MPa.

Joining of Al-Alloy Tubes by Carbon Steel Tubes using MPW Technique

Background/ Objectives: Joining aluminum alloys with low carbon steel (DC01) through fusion welding is a challenging task due to the occurrence of solidification defects like porosity, alloy segregation, and hot cracking. However, these issues can be addressed by employing solid-state welding techniques like explosive welding and MPW (magnetic pulse welding). MPW is a cost-effective and high-speed solid state welding method that involves creating joints in an overlap configuration. Methods: The MPW technique was employed to join dissimilar aluminum alloy AL 7075T6 hollow tube and DC01 steel rod in this study. A central composite design model was created to analyze the relationship between key MPW process parameters, including stand-off distance (SoD), overlap length, and discharge energy, and the bonding strength of the joints. Experimental setups were established and correlate with tensile-shear fracture load and interface hardness of the joints with the MPW process parameters. Findings: It is understood that the maximum TSFL of 2.404 kN was obtained under the welding condition of 23kJ discharge energy, 2.25 mm Stand-off distance, 8.5 mm overlap length, which is the optimum MP welding state for AA 7075 T6 with DC01 and confirmed by RSM. In addition, the cultivated connection can be aptly leveraged to anticipate the TSFL of MPW joints with a 95% confidence level. Novelty: The parametric mathematic samples were developed for forecasting TSFL of joints. The MPW parameters were optimized to enhance TSFL of joints. Aluminium alloys with low carbon steel joints were developed using MPW for cars and ships applications without fusion welding defects. Keywords: Magnetic Pulse Welding, Dissimilar Joint, (RSM) Response Surface Methodology, Tensile Shear-Fracture Load

Fracture Resistance of Posterior Milled Nanoceramic Crowns after Thermomechanical Aging.

Fracture resistance is an important parameter used to predict the performance of indirect dental restorations. The purpose of this in vitro study was to assess the fracture load of posterior milled nanoceramic crowns, in comparison with the lithium disilicate crowns, after fatigue loading, for two different restoration occlusal thicknesses. Forty test metal dies were fabricated by duplicating a master metal model consisting of an anatomic abutment preparation of the maxillary first premolar for a single crown. The dies were divided into two groups of 20 each for the fabrication of nanoceramic (Lava Ultimate) and lithium disilicate (IPS e.max CAD) single crowns. Each material group was further divided into two sub-groups of 10 dies each, based on crown occlusal thickness, of 0.5-mm and 0.75-mm (n = 10). Dental Type V stone dies poured from polyvinyl siloxane impressions of the test metal dies were laboratory scanned in order to design and mill 40 ceramic crowns. The crowns were cemented on to the test metal dies with a self-adhesive resin luting cement. All crowns were thermocycled (2500 cycles) and mechanically loaded (250,000 cycles) in a chewing simulator followed by static loading until failure, and the values noted. The data were statistically analyzed by 2-way ANOVA and Tukey HSD post-hoc multiple comparison tests (α = 0.05). The mean fracture loads ranged from 1022 to 1322 N for nanoceramic crowns and from 1145 to 1441 N for the lithium disilicate crowns. Two-way ANOVA revealed insignificant differences between the nanoceramic and lithium disilicate crowns (p > 0.05) in terms of fracture load. Significant differences were noted in the fracture resistance of crowns based on occlusal thickness (303 N; p = 0.013) regardless of the material used. Multiple comparisons by Tukey HSD post-hoc test showed insignificant differences between the four material-occlusal thickness groups (p > 0.05). The nanoceramic crowns were found to be comparable with lithium disilicate crowns in terms of fracture load. The mean fracture loads of all of the tested crowns were within the normal physiological masticatory load limits. Based on the fracture-resistance results, nanoceramic crowns seem to be suitable for clinical use for the tested occlusal thicknesses.

Effect of the CAD/CAM Milling Protocol on the Fracture Behavior of Zirconia Monolithic Crowns.

Although advancements in CAD/CAM technology allow for more personalized treatments, it is not clear how modifications in the CAD/CAM milling process could affect the restoration surface conditions and their mechanical behavior. The objective of this study was to evaluate the effect of different CAD/CAM milling protocols on the topography and fracture behavior of zirconia monolithic crowns (3Y-PSZ) subjected to a chewing simulation. Monolithic 3Y-PSZ premolar crowns were milled using three protocols (n = 13) (slow (S), normal (N), and fast (F)). Crowns were cemented on a dentin analog abutment and subjected to mechanical aging (200 N, 2 Hz, 1,500,000 cycles, 37 °C water). Surviving crowns were subjected to compressive load test and analyzed using fractography. Fracture load data were analyzed with two-parameter Weibull analysis. The surface topography of the crowns was examined with a stereomicroscope and a 3D non-contact profiler. All crowns survived the chewing simulation. Crowns milled using the F protocol had the greatest characteristic fracture load, while crowns produced with the S protocol showed high Weibull modulus. Groups N and S had a more uniform surface and detailed occlusal anatomy than group F. The CAD/CAM milling protocol affected the topography and mechanical behavior of 3Y-PSZ monolithic crowns.

Feasibility biomechanical study of injectable Biphasic Calcium Phosphate bone cement augmentation of the proximal femoral nail antirotation (PFNA) for the treatment of two intertrochanteric fractures using cadaveric femur

This study evaluated the feasibility of the femoral bone after fixation using biphasic calcium phosphate cement-augmentation of the proximal femoral nail antirotation (PFNA) compared with PFNA without cement. This study presented to compare the stiffness, fatigue testing, and compressive strength between stable (AO31-A2.1) and unstable (AO31-A3.3) intertrochanteric fractures treated by cement augmented PFNA of the cadaveric femoral. Biphasic calcium phosphate cement was injected to align and compatible with PFNA and the reconstructive procedure was monitored the cement placement using x-ray imaging during operation. The testing demonstrated that the cement could be injected through a small needle (13 G, 16 cm length, 1.8 mm inner diameter) within a suitable operating time. The feasibility study of the biomechanical testing was divided into three tests: stiffness test, fatigue cyclic load, and compression test. The results showed that the cement-augmented specimens exhibited higher stiffness than the control specimens without cement. The cement-augmented specimens also showed lower strain energy during the fatigue test, resulting in higher compressive strength (4730.7 N) compared to the control specimens (3857.4 N). There is a correlation between BMD and fracture load and the increase in compression load of the cement-augmented femoral compared to the controls as well as an increase in strain energy of fatigue cyclic testing was found. Biphasic calcium phosphate cement-augmented of the PFNA biomechanically enhanced the cut-out resistance in intertrochanteric fracture. This procedure is especially efficient for unstable intertrochanteric fracture suggesting the potential benefits of using biphasic calcium phosphate cement in medical applications.

High muscular fitness level may positively affect bone strength and body composition in children with overweight and obesity

SummaryMuscular fitness plays a major role in bone health and body composition in overweight and obese children. It is key that the development of this muscle fitness is affected by absolute isometric strength and dynamic strength.PurposeTo compare bone health and body composition between overweight/obese children considering muscular fitness (MF) levels, and to investigate whether weight-bearing dynamic or absolute isometric strength, both involved in the development of this muscular fitness, are more related with bone health.MethodsMF of 59 overweight or obese children (10.1 ± 0.9 years, 27 females) was measured by a countermovement jump (CMJ), handgrip, and maximal isometric strength of knee extension. Participants were divided into four groups depending on their MF level performing a cluster analysis: 16 children with high MF (HMF) in all tests, 18 with high performance in isometric strength (HIS), 15 with high performance in CMJ (HCMJ) and 10 low isometric and low dynamic force values (LMF). Body composition values were measured by dual energy X-ray absorptiometry, and bone strength values were assessed by peripheral quantitative computed tomography. Motor skills were evaluated using TGMD-3. Multivariate analysis of covariance test was applied to analyse bone strength differences between children in the different MF groups, using maturity offset, height and weight as covariates, and correlations were investigated.ResultsHMF excelled in bone health. HIS had higher cortical bone area, periosteal circumference, bone mass, polar strength strain index and fracture load than LMF, while HCMJ only showed better results in trabecular bone area than LMF. HMF had significantly better values of fracture load and periosteal and endosteal circumferences than HCMJ, but not than HIS.ConclusionsHigh MF level shows positive effects on bone health in overweight/obese children. Those with highest isometric strength had better bone health compared to those with higher dynamic strength.Trial registrationThe research project was registered in a public database Clinicaltrials.gov in June 2020 with the identification number NCT04418713.

Application of non-destructive testing methods for assessing fracture resistance in dental ceramics: the sound harvesting test

IntroductionEvaluating the fracture resistance of dental ceramics such as monolithic zirconia crowns is crucial for assessing their durability. Conventional destructive laboratory tests often fail to accurately evaluate the timing and failing crack formation of these brittle materials. Non-destructive testing methods, such as acoustic emission testing (AET), offers an alternative by providing valuable data on material properties without causing damage to the samples.The in vitro study aimed to evaluate the sensitivity of a sound harvesting modified acoustic emission testing by comparing the fracture resistance of posterior monolithic zirconia crowns (MZCs) measured via the modified set up with that of a conventional fracture toughness test.Material and methodsA modified acoustic emission set up, the sound harvesting test (SHT), featuring a condenser microphone, an amplifier, a custom audio chipset and a cut-off switch integrated into a universal testing machine, was compared to a conventional fracture toughness test to measure fracture loads on 50 posterior monolithic zirconia crowns divided in two groups.ResultsThe sound harvesting test recorded a mean fracture load of 1,108.99 N, significantly less than the 1,292.52 N measured with the conventional test, indicating a more sensitive detection of fractures. Statistically significant differences (p &amp;lt; 0.05) were observed between the two groups.ConclusionDespite its limitations, the study suggests considering sound harvesting testing as an potential alternative for fracture load testing of dental brittle materials due to its ability to identify failures at lower loads enhancing therefore a more accurate evaluation of the behavior of dental materials. However, further testing on a broader range of dental materials is warranted to improve result accuracy and applicability.

Mechanical performance of patient-specific prefabricated temporary shell versus laboratory-fabricated CAD/CAM provisional implant-supported single-tooth restorations: Alaboratory study.

To evaluate the mechanical performance of patient-specific prefabricated temporary shell versus laboratory-fabricated CAD/CAM provisional restorations on titanium temporary abutments, with and without thermo-mechanical ageing. Implants with a conical connection were divided into four groups (n = 24) and restored with temporary shell or laboratory-fabricated central or lateral incisor PMMA restorations that were relined or bonded on titanium temporary abutments. The diameter of the central and lateral incisor groups' implants was regular (ϕ 4.3 mm) or narrow (ϕ 3.5 mm), respectively. Half of each group's specimens were subjected to ageing, simultaneous thermocycling (5-55°C) and chewing simulation (120,000 cycles, 50 N, 1.7 Hz) resulting in eight groups in total (n = 12). The aged specimens were evaluated with optical microscopy, and survival and complication rates were determined according to modified USPHS criteria. The non-aged specimens and those that had survived ageing were loaded until failure, whereupon bending moments were calculated. Survival rates after ageing were 100% for all groups. Apart from wear facets (ϕ 2-3 mm) on the palatal restoration surface, no complications were observed. The mean fracture load and bending moments ranged between 597.6-847.1 N and 433.3-550.6 Ncm, respectively, with no significant differences between the eight groups (p = .25; p = .20). As patient-specific temporary shell central and lateral incisor provisional implant-supported restorations are mechanically stable enough to withstand clinical bite forces, even after thermo-mechanical ageing, they may serve as an alternative to laboratory-fabricated provisional restorations.

The effect of ferrule and core material on fracture resistance of endodontically treated anterior teeth restored with ceramic crowns after artificial aging

ObjectivesTo assess the influence of ferrule and core type on the fracture strength of endodontically treated anterior teeth (ETAT) and identify the failure mode type and distribution across different core types and ferrule conditions. MethodsSixty extracted human central incisors were endodontically treated, decoronated and divided into two main groups (F=with ferrule, NF=no ferrule). Each main group was further subdivided into three subgroups according to the core material used: direct composite cores (DC), Ribbond fibre-reinforced composite cores (RIB-DC), and glass fibre post (GFP) with direct composite cores (GFP-DC). All specimens received E.max crowns and underwent thermal cycling and cyclic loading. Subsequently, the fracture resistance was tested with static loads applied to the crown restoration. Two-Way ANOVA and Chi square tests identified significant differences among the groups (p < 0.05). ResultsThe means and standard deviations (SD) of fracture loads in Newtons (N) for specimens in the F subgroups were RIB-DC: 465.0 (104.20), GFP-DC: 367.6 (79.59), DC: 275.8 (68.48), and in NF subgroups were RIB-DC: 110.8 (24.33), GFP-DC: 95.6 (25.47), DC: 67.4 (7.46). Specimens with ferrule yielded significantly higher fracture loads than those without ferrule (p = 0.0054). In the F groups, fracture loads of specimens with RIB-DC cores were significantly higher than those with GFP-DC (p = 0.0019) and those with DC (p = 0.0001). Moreover, fracture loads for the GFP-DC were significantly higher than those for the DC (p = 0.0026). The GFP-DC specimens showed the highest incidence of catastrophic failures (p = 0.0420). ConclusionsUsing fibre-reinforced composite (FRC) cores significantly increased fracture resistance in ETAT with ferrule. The failure modes repairable and possibly repairable were dominant in most specimens. Clinical significanceWhen restoring ETAT with insufficient coronal tooth structure, preserving 2 mm of tooth structure ferrule and preparing cores with FRC can increase fracture resistance and reduce the incidence of non-repairable catastrophic fractures of teeth.

Influence of Different Build Directions on the Fracture Load and Surface Roughness of Additively Manufactured Three-unit Provisional Restoration and Comparison with Conventional Methods of Provisional Fabrication

Influence of Different Build Directions on the Fracture Load and Surface Roughness of Additively Manufactured Three-unit Provisional Restoration and Comparison with Conventional Methods of Provisional Fabrication

Modeling and evaluation of the fracture resistance of alkali-resistant glass fibre reinforced concrete under different loading rates

Alkali-resistant glass fibre reinforced concrete (AR-GFRC) has garnered significant interest due to its economic and environmental friendliness. Given the critical importance of evaluating the crack resistance of AR-GFRC under dynamic loading conditions and the size effect inherent in determined fracture parameters using traditional methods, this study aims to propose an analytical approach based on the boundary effect model. The goal is to predict the realistic dynamic tensile strength (ft) and fracture toughness (KIC) while elucidating the rate sensitivity of fracture resistance. Three-point bending tests were conducted on AR-GFRC with three different fibre volumes to investigate dynamic fracture behaviors under varying loading rates. By introducing discrete parameter and the microstructure characteristic parameter that account for material discontinuity and heterogeneity, the realistic dynamic ft and KIC of AR-GFRC can be directly obtained as closed-form solutions upon determining the maximum fracture load from the tests. The results revealed a substantial increase in ft and KIC with an improvement in the loading rate. However, due to relatively weakened fibre activities, the enhancement of dynamic fracture resistance decreases with the increase in fibre content and loading rate.

Comparative Evaluation of Fracture Resistance of Composite Core Buildup Materials: An In Vitro Study.

Aim This study aimed to compare the fracture resistance of different materials used in composite core buildups, including conventional filler composite, nanofiller composite, and short fiber-reinforced composite (SFRC). Methods This in vitro study was conducted on 30 freshly extracted premolars. The teeth were treated using a uniform endodontic procedure, and Fiber Posts (REFORPOST, Angelus) were placed. The teeth were then divided into three groups and restored using different materials. Group 1 was restored using SFRC(everX Posterior, GC, Europe), Group 2 using microfiller composite (Te-Econom Flow, Ivoclar Vivadent), and Group 3 using nanofiller composite (Tetric N-Flow, Ivoclar Vivadent). The restoration materials were then light-cured for 40 seconds. The teeth were placed in a Universal Testing Machine (Instron) and a load was applied with a stainless-steel ball (4 mm diameter) until the tooth fractured. The fracture load for each tooth was recorded, and after the mechanical test, the experimental groups were examined for failure modes. Statistical analysis was performed using SPSS version 21.0 software. A one-way ANOVA test was conducted to compare more than two groups, followed by Tukey's test for post hoc pairwise comparison. Results The mean fracture resistance of the microfiller composite (346.94±44.63) was the lowest among the three groups. When analyzed using Tukey's test at p<0.05, fracture resistance was significantly higher in the SFRC, followed by nanofillers and microfiller composites. Conclusion Due to the increasing demand for aesthetic restorations in recent years, composites have become important in modern restorative dentistry. The development and implementation of composite dental restorative materials rely on a comprehensive understanding of each composite component and consideration of methods for modifying each component. As a result, the findings of this study will be beneficial in determining which material to use based on specific cases.

Measurement of Strength and Fracture Load of Weathered Samples of Polymer Composite Materials

Measurement of Strength and Fracture Load of Weathered Samples of Polymer Composite Materials

Effect of anodizing pretreatment on laser joining stainless steel to CFRTP

Metal-carbon fiber reinforced thermoplastic (CFRTP) hybrid joints have demonstrated its effectiveness in achieving lightweight design concept in engineering application. However, it is difficult to produce high-reliability joint due to differences in physical as well as chemical properties between metal and CFRTP. In this study, porous oxide film was prepared by anodizing treatments with various anodic oxidation times on steel surface to enhance joint performance of laser-welded steel/CFRTP. The maximum steel/CFRTP joint fracture load of 1960 N was reached, which was three times as much as that obtained with pretreated steel. The results indicated that porous structure was introduced into steel surface by anodization process, which resulted in better wettability of molten CFRTP and higher surface roughness, thus contributing to the enhancement of joint area as well as mechanical interlocking at the interface, further improving joint performance. Meanwhile, more Cr-O-C chemical bonds were produced because Cr-rich oxide film formed after anodizing contributed to interfacial chemical reaction. The chemical bond between oxide film and CFRTP was proved through density functional theory (DFT) calculation. Additionally, with the increase of anodic oxidation time, chemical bond content and surface roughness first enhanced and then reduced, which suggested that the porous structure prepared with 20 min anodizing time could best improve the interfacial mechanical interlocking, and promote the chemical bonding as well as steel/CFRTP joint interfacial bonding.

Effect of Welding Parameters on Lap Shear Force of Similar and Dissimilar Friction Stir Spot Welded Aluminium Alloys

Friction stir spot welding (FSSW) is a solid-state single-point welding technique that uses a rotating tool consisting of a shoulder and a pin for joining nonferrous metals and alloys. FSSW produces a keyhole at the welding point, which decreases the mechanical strength of the joints. This study investigates the influences of tool rotational speed (1000, 1250, and 1500 rpm) and dwell time (5, 10, and 15 s) on the shear fracture load of the FSSW joints. Two different grades of aluminium alloy plates, i.e., AA6061 and AA7075 were used to produce similar (7075-7075 and 6061-6061) and dissimilar (6061-7075) alloy joints. The plates with a thickness of 3 mm were folded above each other before a rotating tool pin was plunged through the thickness of the top plate to obtain an FSSW lap joint. It was found that tool rotational speed and dwell time induced a considerable impact on the microstructure, and shear strength. The results indicated that the grain size of microstructure in similar and dissimilar joints was affected by the rotational speed and dwell time. The grain size of the microstructure increased as rotational speed and dwell time increased. The results also showed that a tool rotational speed of 1250 rpm and dwell time of 10 s gave the highest shear fracture load for 7075-7075 similar and 6061-7075 dissimilar joints. However, for 6061-6061 similar joints, the highest mechanical strength was obtained at 1250 rpm and 10 s.

Crack-tip plastic zone and initiation mechanism of rock based on Eshelby stress

The crack initiation and propagation mechanism of rock is significantly related to characteristics of the crack-tip plastic zone due to energy dissipation. In this paper, conservation integral and configurational stress/force is derived by the Noether’s method. The crack-tip configurational stress field is then deduced and analyzed. Additionally, the Drucker–Prager yield criterion of configurational stress is derived and it is used to predict the crack-tip plastic zone of rock. The fracture criteria of rock are also developed based on the critical area and minimum polar radius of the crack-tip plastic zone. Subsequently, the effects of bedding dip angles and porosity on rock mixed mode fracture are investigated, and the fracture resistance of rock is assessed using the resistivity and wave velocity. It is shown that the configurational force as the crack driving force is induced by the invariant transformation of an action integral with respect to translation of a defect. It is also found that the crack-tip plastic zone assessed by Drucker–Prager yield criterion of Cauchy stress is discontinuous at the crack surface while that predicted by yield criterion of configurational stress is continuous. The present fracture criteria take into account the internal friction angle, and the predicted initiation angles and fracture loads are in good agreement with those determined by the maximum tensile stress (MTS) fracture criterion and experiments. The fracture loading envelope decreases with the porosity, bedding dip angles and resistivities of rock, but increases with wave velocity.

The Impact of Bonding Agents and Bone Defects on the Fracture Resistance of Reattached Vertically Root-Fractured Teeth

Many patients experience vertical root fractures, and clinicians often consider conservative treatment options like reattaching the fractured root segments. The study investigated the impact of different bonding agents on the fracture resistance of rebonded vertically fractured teeth with various alveolar bone defects. Human premolar teeth with a single root were sectioned and reattached using dual-cure resin cement (DCRC), resin-modified glass ionomer (RMGI), and cyanoacrylate. The reattached teeth were then restored with a resin fiber post, composite resin core, and full veneer metal copings. These teeth were embedded in acrylic blocks with angular, V-shaped, and step-shaped bone defects to simulate various alveolar bone conditions. After subjecting the samples to thermal cycling, the fracture resistance was evaluated using a universal testing machine. Teeth samples reattached with RMGI exhibited a higher average fracture resistance. The study also found that DCRC proved to be an effective bonding agent for VRF teeth. However, cyanoacrylate-rebonded teeth exhibited the lowest fracture resistance. The V-shaped defects had a significant impact on the fracture resistance of reattached VRF teeth, with largely unfavorable fractures observed in these cases. Predominantly favorable fractures were observed in the teeth treated with RMGI. The fracture loads in both RMGI and DCRC groups exceeded the expected masticatory load.