fractional-N Digital Phase-locked Loop Research Articles

A DTC-based Fractional-N DPLL using probability-density-shaping spur immunity and Q-noise reduction techniques for IoT applications

A Digital-to-Time Converter based (DTC-based) fractional-N digital phase-locked loop (DPLL) using probability-density-shaping (PDS) spur immunity and quantization phase (Q-noise) reduction techniques is presented. PDS-DSM is used to generate a loop spur immunity control code for DTC. A diff type dither is proposed to further suppress the fractional spur. The loop nonlinearity will not cause fractional spurs if certain conditions are obeyed. Moreover, to reduce the quantization noise, a configurable Phase Interpolator (PI) with 0.125/0.25/0.5/1.0 division step is integrated with a multi-module divider (MMDIV), leading to an 18-dB Q-noise suppression. A reference doubler with duty-cycle correction is adopted to further reduce phase noise. The fractional spurs are greatly mitigated by combining the PDS-DSM and phase interpolator. A DPLL prototype using the aforementioned techniques was designed in a 40-nm standard CMOS process, occupying a 0.99 mm2 silicon area. At a near-integer-N frequency, i.e., near 2.23 GHz, with PDS turned on and off, the post-layout simulated fractional spur is −59 dBc and −20 dBc, respectively. The RMS jitter of the whole chip is 4.218 ps, corresponding to a figure of merit (FOM) of −220.5 dB.

A Power-Efficient Fractional-N DPLL With Phase Error Quantized in Fully Differential-Voltage Domain

This article presents a power-efficient low-jitter fractional-N digital phase-locked loop (DPLL) that resolves phase error (PE) in the fully differential voltage (FDV) domain. Compared with adopting a traditional time-to-digital converter (TDC), which relies on gate delay in the time domain, power-efficient quantization of PE by the proposed conversion scheme in the FDV domain can be accomplished with a higher power-supply/common-mode rejection ratio (PSRR/CMRR), lower process, voltage, and temperature (PVT) sensitivity, finer resolution, and better linearity. The implemented DPLL covers the fractional-N operation by a 10-bit differential current digital-to-analog converter (DAC) with a resistive load to represent the fractional phase/time. A differential dv/dt ramp is employed to linearly transfer the preset initial voltage into a small phase/voltage error, which is digitized by a narrow-range fine-resolution 7-bit self-timed successive-approximation-register analog-to-digital converter (SAR-ADC). The prototype DPLL, implemented in 130-nm CMOS, achieves 101-fs rms jitter, integrated from 10 kHz to 40 MHz, in the fractional-N mode with sub-12-bit fractional-frequency-control words, using an 80-MHz reference clock (REF), consuming 9.2 mW. This corresponds to a figure of merit (FoM) of -250.3 dB. The measured worst case fractional spur level is -56 dBc.

A 0.85mm2 BLE Transceiver Using an On-Chip Harmonic-Suppressed RFIO Circuitry With T/R Switch

This article presents a small-area Bluetooth Low-Energy (BLE) transceiver (TRX) for short-range Internet-of-Things (IoT) applications in 65-nm CMOS. An integrated Radio-Frequency Input-Output (RFIO) circuitry embedded with transmitter/receiver (TX/RX) switch function and on-chip impedance matching is proposed. A hybrid-loop TRX structure based on a wide-bandwidth fractional-N digital phase-locked loop (DPLL) is implemented to achieve the maximum power reduction. A -94dBm receiver sensitivity is achieved with 2.3mW receiver power consumption, while a RF receiving bypass route integration enhances the input power tolerance. The BLE transceiver delivers -6dBm output power while consuming 2.6mW and delivers 0dBm output power while achieving 18.5% maximum TX efficiency. Thanks to the RFIO with harmonic suppression, -56dBc of 2 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">nd</sup> -order harmonic distortion (HD2) and -48dBc of 3 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">rd</sup> -order harmonic distortion (HD3) suppression are achieved with 0.85mm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> on-chip area. This transceiver satisfied the BLE radio specification without the need for external filters and with low-power consumption, which enables minimum size and long life-time modules.

A Novel Parallel DTC Segmentation Scheme for Fractional-N Digital PLLs

In this paper, we propose a new parallel segmentation scheme for the digital/time converter (DTC) which is employed in fractional-N digital phase-locked loops (PLLs) to cancel out the quantization error induced by the digital DS modulator. The proposed parallel scheme removes one redundant least-mean square (LMS) gain in compared with the conventional parallel one. Therefore, the design of the system becomes less complicated while guaranteeing a fast convergence speed of the LMS gains and a short DTC time range. The effectiveness of the proposed segmentation scheme is demonstrated via simulations of a digital PLL built at behavioral level and compared to the conventional segmentation schemes.

A Fast Settling Fractional-$N$ DPLL With Loop-Order Switching

The enhancement in the settling response of frequency synthesizers would open up prospects for new applications such as spread spectra and frequency hopping systems. Toward deriving a methodology for a fast settling response, we present a switched-loop digital phase locked loop (DPLL) incorporating an integral-derivative controller-based subsystem. The dominant features accelerating the settling response with low jitters in this DPLL are: 1) hybrid phase detection with a state machine using differential and double integration filtering effect and 2) a time-interleaved direct digital synthesizer (DDS)-based digital-to-time converter (DTC) with stable-edge sampling. A 5-GHz fractional- $N$ DPLL (FNDPLL) has been implemented in CMOS 65-nm-LL technology with the proposed technique of loop-order switching. The measured results of the implemented FNDPLL highlight that the system is capable of fastest reported frequency settling to ±25-ppm error within 1.5 ${\mu }\text{s}$ , using a reference clock frequency of 100 MHz. With one-time calibration, the downsampled output of DDS array-based phase interpolator achieves an integral nonlinearity (INL) of 0.25 ps, as a fractional divider in the loop.

A 0.0043-mm2 0.3–1.2-V Frequency-Scalable Synthesized Fractional-N Digital PLL With a Speculative Dual-Referenced Interpolating TDC

This paper presents a synthesized fractional-N digital phase-locked loop (PLL) with a speculative dual-referenced interpolating time-to-digital converter (DI-TDC). The DI-TDC measures a fractional phase by referencing two adjacent quadrant boundaries which are given by a four-phase digitally controlled oscillator (DCO). It achieves a robust gain matching to the first order without need of any calibration. By predicting a time region of interest for the next TDC conversion, the power and area overheads for DI-TDC is minimized. Except for DCO and a reference delay chain, the PLL is implemented with register-transfer level (RTL) behavioral descriptions followed by an automated synthesis. It is fabricated in 28-nm CMOS with an active area of 0.0043 mm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> . The PLL shows a wide frequency lock range operating at a supply voltage from 0.3 to 1.2 V, achieving a stable figure-of-merit of better than -220 dB for a supply voltage above 0.6 V.

A DPLL-Centric Bluetooth Low-Energy Transceiver With a 2.3-mW Interference-Tolerant Hybrid-Loop Receiver in 65-nm CMOS

This paper presents a Bluetooth low-energy (BLE) transceiver (TRX) achieving ultra-low-power operation for Internet-of-Things (IoT) applications. The proposed TRX utilizes a wide-bandwidth low-power fractional-N digital phase-locked loop (DPLL) as a central component to perform multiple roles: a direct frequency modulator for the transmitter (TX), an analog-to-digital converter (ADC) for the receiver (RX), a local oscillator for RX, and a frequency and phase synchronizer for the RX. The DPLL-based single-path downconversion method is adapted to halve the analog baseband circuit to further reduce the power consumption while maintaining a high interference rejection. A DPLL-based ADC with a digital-to-analog converter feedback greatly improves the ADC dynamic range, which improves the RX sensitivity and interference tolerance. By maximally reducing the required radio frequency and analog front-end components in RX, an RX power consumption of 2.3 mW is achieved with a −94 dBm sensitivity. The RX also satisfied all interference requirements with a certain margin. A 5.0-mW TX is achieved when delivering an output power of 0 dBm with a frequency-shift keying error of only 1.89%.

An 802.11a/b/g/n Digital Fractional- $N$ PLL With Automatic TDC Linearity Calibration for Spur Cancellation

A fractional-N digital phase-locked loop (PLL) architecture with low fractional spur is presented in this paper. A 2-D Vernier time-to-digital convertor (TDC) is implemented to achieve wide detection range with fine resolution. The TDC is calibrated automatically utilizing the ramp signal generated from the fractional-N accumulator for optimal linearity. A digi-phase spur cancellation technique with automatic TDC gain tracking is also implemented to further suppress the fractional spurs. The chip also includes an improved multimodulus divider (MMD) structure that overcomes the glitch problem during division ratio toggling associated with the prior art MMDs, enabling carrier synthesis across wide frequency range continuously. As part of an 802.11a/b/g/n transceiver, the DPLL can provide coverage for both 2.4/5 G WiFi bands. The proposed fractional-N DPLL is implemented in a 55-nm CMOS technology. The DPLL achieves a largest fractional spur level of −55 dBc without using a sigma–delta modulator and an in-band phase noise of −107 dBc/Hz (0.55 ps integrated jitter) while consuming 9.9 mW.

A Digital PLL With Feedforward Multi-Tone Spur Cancellation Scheme Achieving &lt;–73 dBc Fractional Spur and &lt;–110 dBc Reference Spur in 65 nm CMOS

This paper proposes a fractional-N digital phase-locked loop (DPLL) architecture with feedforward multi-tone spur cancellation scheme. The proposed cancellation loop is capable of suppressing both internal spur, i.e., fractional-N spur, and externally coupled spur from input paths. It can be further extended for multi-stage operation for mitigating multiple spur sources. Both theoretical analysis and simulation results are provided in this paper to explore the design tradeoffs of the proposed technique. A proof-of-concept prototype is implemented in 65 nm CMOS. It measures external spur reduction of 15 to 35 dB and the worst-case fractional spur of 73.66 to 117 dBc with 20–50 dB improvement after enabling the cancellation loop. The measured reference spur ranges from 110.1 to 116.1 dBc across the entire DPLL operation range (3.2–4.8 GHz) thanks to design techniques. The measured in-band phase noise achieves 103 dBc at 100 kHz frequency offset and out-of-band phase noise of 122 dBc at 3 MHz frequency offset with integrated phase noise of 38.1 dBc from 10 kHz to 40 MHz.

A 3.6 GHz Low-Noise Fractional-N Digital PLL Using SAR-ADC-Based TDC

This paper presents a fractional-N digital phase-locked loop (PLL) that achieves low in-band phase noise. Phase detection is carried out by a proposed 10-bit, 0.8 ps resolution time-to-digital converter (TDC) using a charge pump and a successive-approximation-register analog-to-digital converter (SAR-ADC) with low power and small area. The latency of the TDC is addressed by the designed building blocks. The fractional spurs are reduced by dual-loop least-mean-square (LMS) calibration. A $\Delta \Sigma $ -less and MOS varactor-less LC digitally-controlled oscillator (DCO) is proposed whose frequency resolution is enhanced to 7 kHz (or a unit variable capacitance of 2.6 aF) using a bridging capacitor technique. A prototype chip is fabricated using a 65 nm CMOS process, occupying an active area of 0.38 mm2 and consuming a power of 9.7 mW at a reference frequency of 50 MHz. The measured in-band phase noise is 107.8 dBc/Hz to 110.0 dBc/Hz with a loop bandwidth of 1 to 5 MHz.

A Fractional-N Counter-Assisted DPLL With Parallel Sampling ILFD

A fractional-N digital phase-locked loop (DPLL) with ring oscillator based injection-locked frequency divider (ILFD) and parallel sampling phase samplers is presented. The ILFD utilizes dual path injection technique to achieve wide locking range (4.2–23 GHz) and low power consumption. A low-power parallel sampling phase sampler based time-to-digital converter (TDC), which achieves sub-gate-delay resolution by sampling the ILFD’s multi-phase outputs using parallel sampling technique, is proposed. The TDC resolution is determined by delay spacing between successive sampling clocks, which is ensured through digital calibration loops. Due to injection locking, no calibration is required to normalize the TDC step to the DCO output period. A hybrid high speed counter architecture, combining a 2 bit asynchronous counter and a 6 bit synchronous counter, is proposed to achieve high speed (>4 GHz) operation with low power consumption. The proposed design is fabricated in a 65 nm CMOS process and occupies 0.1 mm2. The synthesizer covers 13.6–16.8 GHz output and dissipates 8.5 mW. The measured output phase noise achieves −89 dBc/Hz and −125 dBc/Hz at 100 kHz and 10 MHz offsets, respectively. The measured jitter is less than 0.43 ps.

A 1.9-GHz Fractional-N Digital PLL With Subexponent $ \Delta\Sigma$ TDC and IIR-Based Noise Cancellation

This brief presents a 1.9-GHz fractional-N digital phase-locked loop (DPLL) with a subexponent ΔΣ time-to-digital converter (TDC) and an infinite impulse response (IIR)-based noise cancellation scheme. The proposed subexponent ΔΣ TDC generates adaptively scaled exponent-only information to track the finest resolution that prevents overloading for a given input environment. In addition, IIR-based noise cancellation provides easy filtering of delta-sigma modulator noise without tightened matching constraints. The DPLL fabricated in 0.13- μm CMOS consumes 8.6 mW and shows the subexponent operation and IIR noise cancellation. The measured phase noise of DPLL is - 98 dBc/Hz at 200-kHz offset and -111 dBc/Hz at 3-MHz offset with 500-kHz loop bandwidth.