Fourier Transform Infrared Spectra Research Articles

Aqueous removal of Cr(VI) by Citrus sinensis juice-coated multi-walled carbon nanotubes

A novel adsorbent was prepared from multi-wall carbon nanotubes (MWCNTs) and Citrus sinensis juice extract-modified MWCNTs (OJMW) and characterized using scanning electron microscopy (SEM), Fourier transform infrared spectra (FTIR), X-ray diffractometer (XRD), BET and thermogravimetric analysis. The results showed that the nanotubes exhibited good surface area, pore size, functional groups, and robust stability at elevated temperatures (308 and 313 K). The adsorbent was applied in water for the sequestration of Cr(VI). The adsorption of Cr(VI) on MWCNTs and OJMW was influenced by factors of adsorption. Optimum removal of Cr(VI) was attained at 180 min contact time, 0.05 g adsorbent dose, and solution pH 2 for MWCNTs and OJMW. The kinetic behaviour of the Cr(VI) adsorption onto MWCNTs and OJMW was governed by the pseudo-first-order and pseudo-second-order kinetic model, respectively. The equilibrium data obtained for the uptake of Cr(VI) onto MWCNTs and OJMW fitted satisfactorily with Freundlich and Langmuir isotherm models, respectively. Meanwhile, MWCNTs and OJMW exhibited monolayer adsorption capacities (qmax) of 44.72 and 12.26 g g−1, respectively, at 298 K. The adsorption process was spontaneous and feasible. The direction of energy flow in the uptake of Cr(VI) onto OJMW and MWCNTs followed endothermic and exothermic adsorption processes, respectively. The adsorption–desorption experiments showed that OJMW had good regenerative abilities.

Catalytic Reduction of 4-Nitrophenol and Methylene Blue with Silver Nanoparticles Decorated with Drymoglossum piloselloides Extract

Drymoglossum piloselloides is one of the epiphytic plants that is commonly found in Southeast Asia region. In this study, the ethanol extract of D. piloselloides plant has been used in the green synthesis of silver nanoparticles. The synthesized silver nanoparticles were characterized by ultraviolet-visible (UV-Vis) spectrophotometry, X-ray diffraction (XRD),Fourier-transform infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM) measurements. The UV-Vis spectrum of silver nanoparticles showed a maximum wavelength at 453 nm. The XRD measurement showed the silver nanoparticles peaks at 38.38°, 44.60°, 64.76°, and 77.62°. The FTIR spectra provided evidence of the interaction between silver and chemicals in the plant extract as a weak signal at 682 cm-1. Meanwhile, TEM revealed an average size of 12.63nm. The synthesised silver nanoparticles were utilised for the reduction of 4-nitrophenol with a conversion percentage of up to 100% with a reduction reaction rate constant of 7.104 s-1. In addition, methylene blue was also successfully reduced with the synthesised silver nanoparticles as the catalyst with a reduction reaction rate constant (k) of 21.150 s-1. This study highlights the superior advantage of utilizing ethanolic extract of D. piloselloides to prepare silver nanoparticles with promising catalytic reduction purposes.

Probing the stability and quality of the cellulose-based Pickering emulsion containing sesamolin-enriched sesame oil by chemometrics-assisted ATR-FTIR spectroscopy

This study presents the employment of Fourier transform infrared (FTIR) spectroscopy with attenuated total reflection and principal component analysis (PCA) to analyze the stability of a Pickering emulsion stabilized by carboxylated-cellulose nanocrystal (cCNC) comprising sesame oil phases with or without sesamolin. FTIR measurements identified an intermolecular hydrogen bond between the ester group of the triglyceride and the carboxyl group of the cCNC to create the emulsion droplet. The spectral bands from the hydroxyl group vibration (3700–3050 cm−1), carbonyl (1744 cm−1), CO groups of the ester triglyceride and cCNC (1160–998 cm−1) markedly discriminated between stabilized and destabilized emulsions. The PCA of FTIR spectra detected the change of molecular interaction during storage according to creaming, aggregation, and coalescence and changes in physicochemical parameters such as droplet size, refractive index, and zeta potential. Hence, PCA enabled the observation of the destabilization of emulsion in real-time.

Consecutive high-performance removal of Cu2+ metal ions and Deltamethrin using multifunctional pyrolysis cuttlebone/cotton fabric nanocomposite

A simple technique was developed for the modification of cotton materials that is inexpensive, environmentally friendly, and very effective. Waste Cotton fabrics (WCFs) are loaded with propolis extract (PE) for Cu2+ removal. Then, Cu2+ underwent a pyrolysis process with modified cuttlebone (CB) at 900 °C for 5 h. The surface of the prepared materials was characterized using X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), Fourier transform infrared (FTIR), BET, particle sizes, thermogravimetric analysis (TGA) and zeta potential analysis. The Cu2+ metal ions from an aqueous solution were removed using WCFs/PE, and DLM was subsequently removed using pyro WCFs/PE/Cu/CB. The as-prepared NPs exhibited the face-centered cubic structure of WCFs/PE/Cu/CB with crystallite sizes ranging from 386.70 to 653.10 nm. FTIR spectra revealed that CB was present on the surface of the resulting WCFs/PE/Cu. SEM revealed the dispersion of a uniformly flower-like morphology over a large area. Sorption studies were performed based on parameters that included pH, dose, contact time, and initial concentration. The adsorption isotherm and the kinetic studies of the DLM adsorption process were applied at a pH of 5.0 and a temperature of 25 °C using several isotherms and kinetic models. The results revealed qmax (20.51 mg/g) with R2 = 0.97, the Langmuir isotherm that best matches the experimental data. Hence, the Langmuir isotherm suggests that it is the model that best describes sorption on homogenous surfaces or surface-supporting sites with various affinities. The correlation coefficient R2, χ2, adjusted correlation coefficient, and error functions like root mean square (RMSE), normalized root mean square error (NRMES), and mean absolute error (MAE) were used to evaluate the best-fit models to the experimental adsorption data. Moreover, cost estimation for the prepared adsorbent WCFs/PE/Cu showed that it costs approximately 3 USD/g, which is a cheap adsorbent compared to other similar adsorbents reported in the literature. The examined WCFs/PE have significant applicability potential for Cu2+-laden wastewater treatment due to their superior Cu2+ metal ions adsorption capability and reusability.The cytotoxicity and safety study showed that at higher concentrations, it resulted in much less cell viability. Additionally, the removal efficiency of Cu2+ metal ions from synthetic, realistic industrial wastewater using WCFs/PE reached up to 96.29 %, demonstrating good adsorption capability. Thus, there is a huge possibility of accomplishing this and performing well. This study paves the way for the reuse and valorization of selected adsorbents following circular economy principles.Two green metrics were applied, the Analytical Eco-scale and the Analytical GREEnness Calculator (AGREE).

ADSORPTION OF CATION DYE USING ACTIVATED CARBON DERIVED FROM GOLDEN SHOWERSEED POD ( C ASSIA FISTULA)

This study investigated the use of Golden shower seed pod (cassia fistula) as an adsorbent for the removal of cationic dye in a batch system. The raw material was Carbonized at 600 oC for one hour to obtain a purely carbonized material; then impregnated with NaOH of 0.1M and allowed to stay for 24 hours to obtain the desired GS-AC activated carbon. The adsorbent was characterized using scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and energy-dispersive X-ray fluorescence (EDXRF) elemental composition analysis. The effects of adsorbent dosage and contact time on the adsorption process were studied in a batch system. The results revealed that, there was good enhancements in pores of the adsorbent GS-AC due to the chemical impregnation. The FTIR spectra showed the presence C-H, NH 2, C-O, and S=O functional groups indicating a favourable surface for adsorption. Batch studies indicated that, the methylene blue uptake decreased with increase in the GS-AC dosage. The amount of Methylene blue adsorbed onto GS-AC increased with time and subsequently remained constant at some point in time with maximum uptake at 500 mg/l. Thus, adsorption capacity of methylene blue increased with longer contact time, indicating a stronger interaction between the adsorbent and the dye. Based on the findings, Golden shower seed pod (cassia fistula) impregnated with NaOH can be used as an alternative and suitable material for cationic dye removal from liquid phase.

Integrated Janus nanofibers enabled by a co-shell solvent for enhancing icariin delivery efficiency

During the past several decades, nanostructures have played their increasing influences on the developments of novel nano drug delivery systems, among which, double-chamber Janus nanostructure is a popular one. In this study, a new tri-channel spinneret was developed, in which two parallel metal capillaries were nested into another metal capillary in a core–shell manner. A tri-fluid electrospinning was conducted with a solvent mixture as the shell working fluid for ensuring the formation of an integrated Janus nanostructure. The scanning electronic microscopic results demonstrated that the resultant nanofibers had a linear morphology and two distinct compartments within them, as indicated by the image of a cross-section. Fourier Transformation Infra-Red spectra and X-Ray Diffraction patterns verified that the loaded poorly water-soluble drug, i.e. icariin, presented in the Janus medicated nanofibers in an amorphous state, which should be attributed to the favorable secondary interactions between icariin and the two soluble polymeric matrices, i.e. hydroxypropyl methyl cellulose (HPMC) and polyvinylpyrrolidone (PVP). The in vitro dissolution tests revealed that icariin, when encapsulated within the Janus nanofibers, exhibited complete release within a duration of 5 min, which was over 11 times faster compared to the raw drug particles. Furthermore, the ex vivo permeation tests demonstrated that the permeation rate of icariin was 16.2 times higher than that of the drug powders. This improvement was attributed to both the rapid dissolution of the drug and the pre-release of the trans-membrane enhancer sodium lauryl sulfate from the PVP side of the nanofibers. Mechanisms for microformation, drug release, and permeation were proposed. Based on the methodologies outlined in this study, numerous novel Janus nanostructure-based nano drug delivery systems can be developed for poorly water-soluble drugs in the future.

Greater difference between airborne and flower pollen chemistry, than between pollen collected across a pollution gradient in the Netherlands

The prevalence in allergic diseases has increased considerably in the past decades. An important trigger of the symptoms of allergic rhinitis (hay fever) is the pollen of wind-pollinating plants. This pollen is developed by plants and is released into the air where it gets exposed to environmental influences and air pollution. We investigated the chemical changes to pollen that occur after release from the flower in a rural (Veluwe) and an urban (Amsterdam) site in the Netherlands using Fourier Transform Infrared (FTIR) spectroscopy. During the spring/summer of 2020 (during the COVID pandemic) the pollen of nine taxa (Alnus, Betula, Fagus, Fraxinus, Pinus, Plantago, Poaceae, Quercus and Salix) were collected directly from flowers and the air (using a mobile sampler). FTIR spectra were obtained for multiple individual pollen grains for each taxa. The spectra obtained from airborne pollen collected at the rural vs. urban sites did not show any statistical difference. This is possibly a result of a reduced difference in pollutant concentrations between the two sites due to the COVID-19-lockdown measures were in place. However, consistent differences in the FTIR spectra recovered from airborne vs. flower pollen were recorded for all pollen taxa. After the release from the flower the chemical composition of the pollen changed: (i) polysaccharides are converted to monosaccharides; (ii) protein concentration and/or nitration/oxidation level is altered; (iii) lipids are modified and/or reduced in concentration. These changes may alter the allergenicity of the pollen and suggest that further work on the allergenic nature of airborne pollen is required.

FTIR determination of the degree of molar substitution for hydroxypropyl chitosan

We developed and validated a novel Fourier transform infrared (FTIR) method to determine the degree of molar substitution (MS) for hydroxypropyl chitosan (HPCS) using nuclear magnetic resonance (1H NMR) as a reference, and investigated the factors influencing the MS assay. Through extensive screening of integration methods for candidate bands in the FTIR spectrum of HPCS using 20 HPCS samples with degrees of acetylation (DA) ranging from 0.003 to 0.139, we found that when using band area at 2970 cm−1 as a probe integral, the MS values obtained via the 1H NMR method exhibited linear correlations (R2 > 0.98) with at least 16 integral ratios derived from their FTIR spectra. The optimal reference bands with high reliability are located at 3440 cm−1 and 1415 cm−1, with R2 exceeding 0.99 and a MS range of 0.17–1.92. The band at 2875 cm−1 is less affected by the trace moisture present in HPCS samples than the others. The results of the method validation demonstrated a mean recovery of 98.9 ± 2.8 % and an RSD below 10 %, suggesting a simple, robust, and highly accurate and precise method. This method could be extendable for the determination of the MS of insoluble HPCS derivatives and other hydroxypropylated polysaccharides.

Preparation, characterization and photocatalytic studies of defect pyrochlore, KMn0·33Te1·67O6 and its composite with g-C3N4

Skeletal materials belonging to the defect pyrochlore family have been the subject of considerable interest due to their remarkable properties. In this work, a highly efficient, stable and visible light active composite photocatalytic system consisting of defect pyrochlore of composition KMn0·33Te1·67O6 (KMnTeO) and g-C3N4 (g-CN) has been successfully prepared by simple physical mixing of pre-prepared KMnTeO and g-CN components synthesized in solid state and thermal treatment of low-cost melamine, respectively. Structural, morphological and optical properties of as-prepared catalysts were deduced from powder X-ray Diffraction (XRD), Fourier Transform Infrared (FT-IR), Raman, Field Emission Scanning Electron Microscopy-Energy Dispersive X-ray Spectroscopy (FESEM-EDX), Transmission Electron Microscopy-High Resolution Transmission Electron Microscopy (TEM-HRTEM), Ultraviolet–Visible Diffuse Reflectance Spectroscopy (UV–Vis DRS), X-ray Photoelectron Spectroscopy (XPS) and Photoluminescence (PL) measurements. The lattice parameter “a” of parent KMnTeO was obtained from Rietveld refinement of its powder XRD pattern. The FT-IR and Raman spectra of KMnTeO gave characteristic bands belonging to the defect pyrochlore structure. The photocatalytic activities of KMnTeO and composite KMnTeO-g-CN were evaluated by the degradation of methylene blue (MB). Scavenger experiments were carried out to identify the reactive species responsible for the degradation of MB. Furthermore, the reusability and stability of the photocatalysts were explored. The probable photocatalytic mechanism for MB degradation over the composite KMnTeO-g-CN was surmised according to the scavenger experiments. The work provides a new approach for the development of novel defect pyrochlore based composite photocatalysts to treat industrial wastewater containing organic pollutants.

Carbon gas sensors synthesized using acacia auriculiformis tree branches to detect methanol, ethanol, acetone vapors and ammonia gas

Metal oxides and carbon are the prime candidates of gas sensor devices. For the inaugural instance, carbonaceous particulate matter was meticulously derived from the branches of Acacia auriculiformis tree indigenous to Sri Lanka to detect vapor and gas. It is worth noting that biomass derived carbon had hitherto remain unexplored in the realm of vapor and gas detection. Carbon films were fabricated via the doctor blade method. The resistivity characteristic of these carbon samples exhibited discernible variations upon exposure to methanol, ethanol, acetone vapors, and ammonia gas. Notably, the gas-sensing properties of sample derived from the central core and the outer shell of Acacia auriculiformis tree branches were independently assessed in these vapors and gas at ambient temperature. Various analytical techniques, including X-ray diffraction (XRD), UVvisible absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM), were judiciously employed to scrutinize the structural attribute, optical band gap, chemical composition and surface morphology of the aforementioned carbon film samples, respectively. XRD analyses unequivocally confirmed the successful formation of carbonaceous films. FTIR spectra conspicuously delineated the presence of oxygen within the carbon films. Importantly, the optical band gap of our carbon films manifested within the range characteristic of organic carbon. Furthermore, the resistance of the carbon films demonstrated a significant reduction upon adsorption of each vapor. It is noteworthy that while gas sensitivities and response times were superior for carbon derived from the central core of the Acacia tree branches, the recovery times were notably expedited for carbon synthesized from the outer shell of these branches. The zenith of gas sensitivity, an impressive 187%, was recorded in response to 1000 ppm of methanol vapor, when employing carbon sourced from the central core of the acacia tree branches.

Fabrication of Magnetic Molecularly Imprinted Polymers for Selective Extraction of Dibutyl Phthalates in Food Matrices.

In this study, a novel magnetic molecularly imprinted polymeric material (Fe3O4@MOF@MIP-160) with a metal-organic backbone (Fe3O4@MOF) carrier was prepared using dibutyl phthalate (DBP) as a template. The material can be used for the efficient, rapid, and selective extraction of trace amounts of phthalic acid esters (PAEs) in food and can detect them via gas chromatography-mass spectrometry (GC-MS). The synthesis conditions of the materials were optimized to prepare the Fe3O4@MOF@MIP160 with the highest adsorption performance. Transmission electron microscopy (TEM), Fourier Transform Infrared Spectra (FT-IR), Vibration Sample Magnetic (VSM), and the Brunauer-Emmett-Teller (BET) method were used to characterize the materials. Compared with Fe3O4@MOF and the magnetic non-imprinted polymeric material (Fe3O4@MOF@NIP), Fe3O4@MOF@MIP-160 possesses the advantages of easy and rapid manipulation of magnetic materials, the advantages of high specific surface area and the stability of metal-organic frameworks, and the advantages of high selectivity of molecularly imprinted polymers. Fe3O4@MOF@MIP-160 has good recognition and adsorption capacity for di-butyl phthalate (DBP) and diethylhexyl phthalate (DEHP): the adsorption capacity for DBP and DEHP is 260 mg·g-1 and 240.2 mg·g-1, and the adsorption rate is fast (reaching equilibrium in about 20 min). Additionally, Fe3O4@MOF@MIP160 could be recycled six times, making it cost-effective, easy to operate, and time-saving as compared to traditional solid-phase extraction materials. The phthalate ester content in drinking water, fruit juice, and white wine was analyzed, with recoveries ranging from 70.3% to 100.7%. This proved that Fe3O4@MOF@MIP160 was suitable for detecting and removing PAEs from food matrices.

Ammonium ion removal from aqueous solutions in the presence of organic compounds, using biochar from banana leaves. Competitive isotherm models

BackgroundIndustrial, e.g. food industrial and domestic wastewaters contain huge amount of compounds causing eutrophication, and should be removed with high cost during wastewater treatment. However, these compounds could be utilized as fertilizers too. Biochar can remove a wide range of pollutants from water, such as ammonium, which can be found in relatively high concentration in dairy wastewaters. However, adsorption performance may be affected by the presence of other wastewater pollutants. Thus, this study aims to determine the efficiency of biochar as an adsorbent of ammonium in aqueous solutions in the presence of some selected organic compounds of typical dairy wastewaters such as bovine serum albumin (BSA), lactose, and acetic acid. Methods: The biochar was produced from banana leaves at 300 °C, modified with NaOH, and characterized by Scanning Electron Microscope – Energy Dispersive X-Ray Spectroscopy (SEM-EDX), Fourier-transform infrared spectra (FTIR) analysis, and specific surface area measurements. Batch experiments were carried out to investigate the ammonium adsorption capacity and the ion competitive adsorption mechanism. Significant Findings: Results show that the surface structure of the biochar derived from banana leaves is different from other biochars previously studied; although the specific surface area is not very considerable and despite having nitrogen within the elemental composition, the biochar studied is capable of adsorbing 2.60 mg NH4+/m2, the highest ammonium removal in 2 h occurs at pH 9 and 500 mg biochar dose. Langmuir model in the monolayer phase analysis fits better for all scenarios and the maximum NH4+ adsorption capacity was 0.97 mg/g without organic compounds. In the multilayer adsorption phase, the isotherm model that best fits the data obtained is the Harkins-Jura model without organic compounds. The presence of organic compounds in the aqueous solution significantly impacts the adsorption of ammonium by biochar since it improves the adsorption capacity (1.132 mg/g BSA, 0.975 mg/g lactose, and 1.874 mg/g acetic acid). The Aranovich-Donohue isotherm model fitted the data obtained during ion competitive adsorption experiments well.

Polyvinyl pyrrolidone/ carboxymethyl cellulose (PVP/CMC) polymer composites containing CuO nanoparticles synthesized via laser ablation in liquids

Polyvinyl pyrrolidone/carboxymethyl cellulose (PVP/CMC) polymer composites containing CuO nanoparticles synthesized via laser ablation in liquids were prepared. Fourier transform infrared (FTIR) spectroscopy, UV/Vis spectroscopy, and scanning electron microscopy (SEM) were used to characterize the structural, optical, and morphological properties of the polymer composites. The addition of CuO nanoparticles resulted in changes in the FTIR spectra, indicating interaction between the polymer matrix and nanoparticles. UV/Vis spectroscopy showed a red shift in absorption and a decrease in optical bandgap with increasing CuO nanoparticle content. SEM micrographs revealed increases in surface roughness with higher CuO nanoparticle loading. Antibacterial activity of the composites against Gram-positive and Gram-negative bacteria increased with greater CuO nanoparticle concentration. The results suggest these biofilms have potential for use as coating materials in biomedical applications.

Role of Nd doping on the structural, morphological and optical properties of BaTiO3 nanoparticles hydrothermally synthesized

Herein, we have reported the facile synthesis of pure and neodymium (Nd)-doped BaTiO3 powders via the hydrothermal method. The effects of Nd concentration (2–10 wt %) on the properties of the BaTiO3 powders were studied. Structural and morphological characteristics were realized using X-ray diffraction (XRD), scanning electronic microscopy (SEM), energy dispersive X-ray (EDS), and X-ray photoelectron spectroscopy (XPS). Fourier transform infrared (FT-IR), UV–visible, and photoluminescence (PL) spectroscopies were used for optical analyses. XRD results show that all powders crystallized under a cubic structure with an average crystallite size that was in the range of 35–47 nm. SEM micrographs revealed that the grains were spherical-shaped, with an average size found in the range of 232–390 nm. The EDS analysis detected the presence of Ba, Ti, O, and Nd elements in the elaborate materials. XPS data confirms the introduction of Nd3+ in the BaTiO3 and the amphoteric substitution of Nd3+ in the Ba and Ti sites at 6 and 10 wt%. FT-IR spectra indicate the presence of the Ti–O vibration bonds. UV–visible optical spectra illustrate the enhancement of absorbance with Nd doping. PL spectra exhibit ultraviolet, blue, green, and orange emissions in the samples.

β-Glucan Extraction from Hull-Less Barley by a Novel Approach: Microwave-Assisted Pressurized CO2/H2O

AbstractΒ-glucans (BGs) are dietary fibers with human health benefits. Due to their emulsifying, thickening, and water-holding properties, they are frequently utilized in food formulations. Hull-less barley is one of the important sources of BGs. This research was performed to extract BGs from hull-less barley using microwave-assisted pressurized CO2/H2O (MW-PCO2) extraction, a combination that had never been employed before. The MW-PCO2 extraction conditions (temperature, time and water: barley flour ratio) were optimized using response surface methodology (RSM) with a Box-Behnken design for the maximum BG yield (%). Temperature of 47.74 °C, time of 19.92 min, and water: barley flour ratio of 10.10:1 (g/g) were found to be the optimum conditions for extraction with a BG yield of 62.43%. Additionally, MW-PCO2 extraction was compared with conventional water extraction (CE) and BG extracts obtained by both methods were characterized. Chemical composition, molecular weight, thermal properties, water solubility, water holding capacity, surface morphology, and Fourier Transform Infrared Spectrum (FTIR) of the BG extracts were determined. MW-PCO2 extraction gave higher BG yield and purity, molecular weight, and water holding capacity using less solvent in a shorter time. Furthermore, both extracts have similar morphological images, FTIR spectrum, and thermal properties. The results of this work demonstrate the potential of the MW-PCO2 approach for extracting BGs from hull-less barley with improved selectivity and recovery, which can then be added to a variety of food and drug formulations.

Thermal annealing gradient tailoring on ammonium nitrate-capped CdS nanospheres synthesized via green precipitation

This study explores the impact of thermal annealing gradients on the physical properties and structural evolution of cadmium sulphide (CdS) nanospheres capped with ammonium nitrate as a modifier, which were fabricated through precipitation and subsequent annealing within 160–480 °C temperature range. The properties were characterized using X-ray diffraction (XRD), ultraviolet–visible (UV–Vis), Fourier transform infrared (FTIR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) techniques The XRD results show that the present CdS exhibits superior crystallinity compared to pure CdS without capping, transitions from a cubic to a hexagonal phase structure, and increases in crystallite size and crystallinity with increasing temperature. The FTIR spectra postulate that a vibrational band presence evidences ammonium nitrate capping on CdS, with another distinct band that represents CdS in the lower wavenumber region, both intensifying at elevated temperatures. The UV–Vis analysis reveals that CdS exhibits strong ultraviolet (UV) absorption suitable for effective photoreaction under UV light and has a broader band gap compared to bulk CdS. SEM images show an extensive distribution of homogeneous nanospheres over the surface, with increased growth in size when capped with ammonium nitrate and at higher temperatures. As validated by TGA and DSC results, CdS with a smaller crystallite size improves thermal stability and energy transfer, as evidenced by reduced weight loss and a lower endothermic temperature, respectively. Varying the annealing temperature with ammonium nitrate capping can improve the structural and physical properties of CdS, which are beneficial for varied applications such as optoelectronics, energy storage, and photocatalysts.

Authentication analysis of goat milk from cow milk using Fourier Transform Infrared spectroscopy and chemometrics

The authentication of higher quality milk such as goat milk (GM) from the lower price of cow milk (CM) is a big issue in the milk industry, because unethical producers may get economic profits from the adulteration practice. This study intended to apply Fourier Transform Infrared (FTIR) spectroscopy and chemometrics for the authentication analysis of GM from CM. The characterization of CM and GM was performed by determining fatty acid composition using gas chromatography. The binary mixtures of GM and CM were prepared for making calibration and validation models and were subjected to FTIR spectral measurement using an attenuated total reflectance (ATR) accessory. The model was optimized by selecting multivariate calibrations of partial least square regression (PLSR) and principal component regression (PCR) along with spectral modes (normal and derivatives) and wavenumbers regions. The results showed that absorbance values at 2nd derivative spectra at wavenumber regions of 1500-800 cm-1 could provide the best accuracy and precision of the developed model. Principal component analysis (PCA) at selected wavenumbers and linear discriminant analysis (LDA) at 3800-800 cm-1 could discriminate authentic GM and GM adulterated with CM without any misclassification objects observed. It concluded that FTIR spectra combined with chemometrics techniques could be used as a reliable method for the authentication analysis of milk products.

Performance test of Zn-astaxanthin complex-sensitized solar cell: effect of light intensity on open-circuit voltage and short-circuit current values.

The sensitizer is one of the most essential dye-sensitized solar cell (DSSC) components. In the present research, a Zn-astaxanthin complex was investigated as a sensitizer, compared to pure astaxanthin. The complex with a 1:1 mole ratio between astaxanthin and Zn2+ was synthesized in a reflux reactor at 37-60 °C. The product was analyzed using Proton Nuclear Resonance (1H-NMR), which indicates the presence of chelate formation between Zn2+ with two atoms of oxygen on the terminal cyclohexane ring of astaxanthin. The interaction of sensitizers (astaxanthin and Zn-astaxanthin) on the photoelectrode surface in this study was analyzed using a Fourier Transform Infra-Red (FTIR) and Ultraviolet-Visible Diffuse Reflectance Spectroscopy (UV-Vis DRS). The FTIR spectra of photoelectrode immersed in Zn-astaxanthin show peaks of C=O stretching and vibration -OH group at 1730 and 1273 cm-1, respectively, and H-C-H stretching vibration with high intensity in 2939, 2923, and 2853 cm-1. The UV-Vis DRS analysis shows the band gap of photoelectrode (PE), photoelectrode immersed in astaxanthin (PE/astaxanthin), and Zn-astaxanthin (PE/Zn-astaxanthin) are 3.19, 1.65, and 1.59 eV, respectively. Under illumination intensity of 300 W/m2, the maximum energy conversion efficiency of DSSC with Zn-astaxanthin as sensitizer is (0.03 ± 0.0022)%, higher than DSSC with astaxanthin as sensitizer ((0.12 ± 0.0052)%). Up to 70 h of illumination, DSSC with Zn-astaxanthin as a sensitizer also has better stability than astaxanthin-based DSSC.

A new strategy to improve the anticorrosion performance of waterborne polyurethane coating on AA7075

In this study, Ce3+ functionalised halloysite nanotubes (HNTs) were prepared, and their impact on the anticorrosion properties of waterborne polyurethane (WPU) coating on 7075 aluminium alloy (AA7075) was investigated. HNTs were grafted by 3-aminopropyltriethoxysilane (APTES) to enhance Ce3+ loading, which was confirmed by X-ray diffraction (XRD) and Fourier-transform infrared (FT-IR) spectrum. The release behaviour of Ce3+ from HNTs was tested by inductively coupled plasma optical emission spectrometry (ICP-OES), and the inhibition effect of Ce3+-loaded HNTs for AA7075 was tested by polarization plots. The anticorrosion property of WPU doped with Ce3+-loaded HNTs was investigated by electrochemical impedance spectroscopy (EIS) and pull-off adhesion test. The results showed that APTES modification improved the Ce3+ loading amount on HNTs, and Ce3+ acts as an effective cathodic inhibitor for AA7075. After soaking for 40 days, the |Z|0.01Hz of Ce-HNTs/WPU was two orders of magnitude higher than that of pure WPU, while wet put-off adhesion was higher than pure WPU.

Impact of Oil Bodies on Structure, Rheology and Function of Acid-Mediated Soy Protein Isolate Gels.

Oil bodies (OBs) are naturally occurring pre-emulsified oil droplets that have broad application prospects in emulsions and gels. The main purpose of this research was to examine the impact of the OB content on the structure and functional aspects of acid-mediated soy protein isolate (SPI) gel filled with OBs. The results indicated that the peanut oil body (POBs) content significantly affected the water holding capacity of the gel. The rheological and textural analyses showed that POBs reduced the gel strength and hardness. The scanning electron and confocal laser scanning microscopy analyses revealed that POBs aggregated during gel formation and reduced the gel network density. The Fourier transform infrared spectrum (FTIR) analysis demonstrated that POBs participated in protein gels through hydrogen bonds, steric hindrance and hydrophobic interactions. Therefore, OBs served as inactive filler in the acid-mediated protein gel, replaced traditional oils and provided alternative ingredients for the development of new emulsion-filled gels.