Formamidinium Research Articles

Overcoming Microstructural Defects at the Buried Interface of Formamidinium-Based Perovskite Solar Cells.

Since the advent of formamidinium (FA)-based perovskite photovoltaics (PVs), significant performance enhancements have been achieved. However, a critical challenge persists: the propensity for void formation in the perovskite film at the buried perovskite-interlayer interface has a deleterious effect on device performance. With most emerging perovskite PVs adopting the p-i-n architecture, the specific challenge lies at the perovskite-hole transport layer (HTL) interface, with previous strategies to overcome this limitation being limited to specific perovskite-HTL combinations; thus, the lack of universal approaches represents a bottleneck. Here, we present a novel strategy that overcomes the formation of such voids (microstructural defects) through a film treatment with methylammonium chloride (MACl). Specifically, our work introduces MACl via a sequential deposition method, having a profound impact on the microstructural defect density at the critical buried interface. Our technique is independent of both the HTL and the perovskite film thickness, highlighting the universal nature of this approach. By employing device photoluminescence measurements and conductive atomic force microscopy, we reveal that when present, such voids impede charge extraction, thereby diminishing device short-circuit current. Through comprehensive steady-state and transient photoluminescence spectroscopy analysis, we demonstrate that by implementing our MACl treatment to remedy these voids, devices with reduced defect states, suppressed nonradiative recombination, and extended carrier lifetimes of up to 2.3 μs can be prepared. Furthermore, our novel treatment reduces the stringent constraints around antisolvent choice and dripping time, significantly extending the processing window for the perovskite absorber layer and offering significantly greater flexibility for device fabrication.

Long-Term Comparisons of Photoluminescence Affected by Organic Cations of Formamidinium and Methylammonium in Monophasic Lead Iodide Perovskite Quantum Dots.

This study compared the photoluminescence (PL) stabilities of formamidinium (FA) and methylammonium (MA) in lead iodide perovskite quantum dots (QDs). To exclude other factors, such as size and purity, that may affect stability, MAPbI3 and FAPbI3 QDs with nearly identical sizes (~10.0 nm) were synthesized by controlling the ligand concentration and synthesis temperature. Transmission electron microscopy images and X-ray diffraction patterns confirmed homogeneous single-phase perovskite structures. Additionally, the bandgaps and sizes of the synthesized QDs closely matched those of the infinite quantum well model, which guaranteed that the photostability was solely caused by the different organic molecules in the two QDs. We analyzed the PL peak centers and full-width at half maximum of the QDs for 32 days. The enhanced stability of FAPbI3 was found to be caused by the nearly zero redshift (1.615 eV) of its PL peak, in contrast to the redshift (1.685→1.670 eV) of MAPbI3.

Identification and Suppression of Point Defects in Bromide Perovskite Single Crystals Enabling Gamma-Ray Spectroscopy.

Methylammonium lead tribromide (MAPbBr3) stands out as the most easily grown wide-band-gap metal halide perovskite. It is a promising semiconductor for room-temperature gamma-ray (γ-ray) spectroscopic detectors, but no operational devices are realized. This can be largely attributed to a lack of understanding of point defects and their influence on detector performance. Here, through a combination of crystal growth design and defect characterization, including positron annihilation and impedance spectroscopy, the presence of specific point defects are identified and correlated to detector performance. Methylammonium (MA) vacancies, MA interstitials, and Pb vacancies are identified as the dominant charge-trapping defects in MAPbBr3 crystals, while Br vacancies caused doping. The addition of excess MABr reduces the MA and Br defects and so enables the detection of energy-resolved γ-ray spectra using a MAPbBr3 single-crystal device. Interestingly, the addition of formamidinium (FA) cations, which converted to methylformamidinium (MFA) cations by reaction with MA+ during crystal growth further reduced MA defects. This enabled an energy resolution of 3.9% for the 662keV 137Cs line using a low bias of 100V. The work provides direction toward enabling further improvements in wide-bandgap perovskite-based device performance by reducing detrimental defects.

Hole Localization in Bulk and 2D Lead-Halide Perovskites Studied by Time-Resolved Infrared Spectroscopy.

Scattering and localization dynamics of charge carriers in the soft lattice of lead-halide perovskites impact polaron formation and recombination, which are key mechanisms of material function in optoelectronic devices. In this study, we probe the photoinduced lattice and carrier dynamics in perovskite thin films (CsFAPbX3, X = I, Br) using time-resolved infrared spectroscopy. We examine the CN stretching mode of formamidinium (FA) cations located within the lead-halide octahedra of the perovskite structure. Our investigation reveals the formation of an infrared mode due to spatial symmetry breaking within a hundred picoseconds in 3D perovskites. Experiments at cryogenic temperatures show much-reduced carrier localization, in agreement with a localization mechanism that is driven by the dynamic disorder. We extend our analysis to 2D perovskites, where the precise nature of charge carriers is uncertain. Remarkably, the signatures of charge localization we found in bulk perovskites are not observed for 2D Ruddlesden-Popper perovskites ((HexA)2FAPb2I7). This observation implies that the previously reported stabilization of free charge carriers in these materials follows different mechanisms than polaron formation in bulk perovskites. Through the exploration of heterostructures with electron/hole excess, we provide evidence that holes drive the formation of the emerging infrared mode.

Enhancing the Efficiency and Stability of Inverted Formamidinium-Cesium Lead-Triiodide Perovskite Solar Cells through Lewis Base Pretreatment of Buried Interfaces.

Mixed components of formamidinium(FA) and cesium (Cs)-based perovskite solar cells are the most hopeful for commercialization owing to their excellent operational and phase stabilities, especially for devices with inverted structure. The nonradiative recombination of carriers can be effectively suppressed through interface optimization, therefore, the performance of devices can be improved. Notably, the buried interface emerges as critical aspects such as charge transport, charge recombination kinetics, and morphology of perovskite films. This study focuses on a straightforward yet effective approach to overcome buried interface challenges between organic polymers (poly(-triarylamine) (PTAA) and FACs-based perovskite films. The PTAA substrate is pretreated with a Lewis base known as 2-butynoic acid (BA) with a C═O functional group. First, it can be an interfacial buffering layer, harmonizing stress mismatch between the perovskite and PTAA layers, consequently optimizing crystallization and improving perovskite film quality. Second, Pb2+ defect can be passivated at the buried interface of the perovskite film through binding with the C═O group of the BA molecule. This dual-function strategy leads to a substantial enhancement in both photoelectric conversion efficiency (PCE) and stability of devices. Finally, the PCE of the device-modified buried interface with BA reaches an impressive 23.33%. Furthermore, unencapsulated devices with BA treatment maintain approximately 94% of their initial efficiency after aging at maximum power point tracking for 1000 h.

Thermal Stability of Encapsulated Carbon-Based Multiporous-Layered-Electrode Perovskite Solar Cells Extended to Over 5000 h at 85 °C.

The key to the practical application of organometal-halide crystals perovskite solar cells (PSCs) is to achieve thermal stability through robust encapsulation. This paper presents a method to significantly extend the thermal stability lifetime of perovskite solar cells to over 5000 h at 85 °C by demonstrating an optimal combination of encapsulation methods and perovskite composition for carbon-based multiporous-layered-electrode (MPLE)-PSCs. We fabricated four types of MPLE-PSCs using two encapsulation structures (over- and side-sealing with thermoplastic resin films) and two perovskite compositions ((5-AVA)x(methylammonium (MA))1-xPbI3 and (formamidinium (FA))0.9Cs0.1PbI3), and analyzed the 85 °C thermal stability followed by the ISOS-D-2 protocol. Without encapsulation, FA0.9Cs0.1PbI3 exhibited higher thermal stability than (5-AVA)x(MA)1-xPbI3. However, encapsulation reversed the phenomenon (that of (5-AVA)x(MA)1-xPbI3 became stronger). The combination of the (5-AVA)x(MA)1-xPbI3 perovskite absorber and over-sealing encapsulation effectively suppressed the thermal degradation, resulting in a PCE value of 91.2% of the initial value after 5072 h. On the other hand, another combination (side-sealing on (5-AVA)x(MA)1-xPbI3 and over- and side-sealing on FA0.9Cs0.1PbI3) resulted in decreased stability. The FACs-based perovskite was decomposed from these degradation mechanisms by the condensation reaction between FA and carbon. For side-sealing, the space between the cell and the encapsulant was estimated to contain approximately 1,260,000 times more H2O than in over-sealing, which catalyzed the degradation of the perovskite crystals. Our results demonstrate that MA-based PSCs, which are generally considered to be thermally sensitive, can significantly extend their thermal stability after proper encapsulation. Therefore, we emphasize that finding the appropriate combination of encapsulation technique and perovskite composition is quite important to achieve further device stability.

Bridging-Solvent Strategy for Quasi-Single-Crystal Perovskite Films and Stable Solar Cells.

Controllable fabrication of formamidinium (FA)-based perovskite solar cells (PSCs) with both high efficiency and long-term stability is the key to their further commercialization. However, the diversity of PbI2 complexes and perovskite compositions usually leads to light sensitive PbI2 residues and phase impurities in the film, which can accelerate the device degradation. Here, the crystallization kinetics of FA-based perovskite films are studied and a bridging-solvent strategy is proposed to modulate the reaction kinetics between PbI2 and ammonium salts by prohibiting the formation of undesired intermediates. N-methylpyrrolidone (NMP) solvent is introduced into the PbI2 precursor solution to obtain stable and homogeneous PbI2-NMP complex films. The strong interaction between NMP and formamidinium iodide (FAI) molecules promotes the conversion from PbI2-NMP into (001)-oriented quasi-single-crystal perovskite films with negligible impurities, long carrier lifetime of 1.5µs and a large grain size of 3µm. The optimized PSCs exhibit a high power conversion efficiency of 24.1%, as well as superior shelf stability which maintains 95% initial efficiency after storage in air for 1200h (T95=1200h), and operating stability with T96=300h under continuous working at the maximum power point. This work offers a simple and reproducible method for fabricating phase-pure and uniaxially oriented perovskite films.

Using scalable computer vision to automate high-throughput semiconductor characterization

High-throughput materials synthesis methods, crucial for discovering novel functional materials, face a bottleneck in property characterization. These high-throughput synthesis tools produce 104 samples per hour using ink-based deposition while most characterization methods are either slow (conventional rates of 101 samples per hour) or rigid (e.g., designed for standard thin films), resulting in a bottleneck. To address this, we propose automated characterization (autocharacterization) tools that leverage adaptive computer vision for an 85x faster throughput compared to non-automated workflows. Our tools include a generalizable composition mapping tool and two scalable autocharacterization algorithms that: (1) autonomously compute the band gaps of 200 compositions in 6 minutes, and (2) autonomously compute the environmental stability of 200 compositions in 20 minutes, achieving 98.5% and 96.9% accuracy, respectively, when benchmarked against domain expert manual evaluation. These tools, demonstrated on the formamidinium (FA) and methylammonium (MA) mixed-cation perovskite system FA1−xMAxPbI3, 0 ≤ x ≤ 1, significantly accelerate the characterization process, synchronizing it closer to the rate of high-throughput synthesis.

Effects of the Addition of Tin Powder to Perovskite Precursor Solutions on Band Bending at PEDOT:PSS/Perovskite Interfaces in Mixed-Cation Mixed-Halide Tin Perovskite Solar Cells.

Using electron spin resonance (ESR) spectroscopy, we investigated the effects of the addition of tin (Sn) powder to perovskite layers on band bending at the perovskite surface near poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) hole-transport layers in perovskite solar cells (PSCs) involving formamidinium (FA)-methylammonium (MA)-mixed-cation I-Br-mixed-halide tin perovskites. We performed dark ESR spectroscopy measurements of a PEDOT:PSS/FA0.75MA0.25Sn(I0.75Br0.25)3 stack and of a PEDOT:PSS/Sn-powder-added FA0.75MA0.25Sn(I0.75Br0.25)3 stack. The results indicate that FA0.75MA0.25Sn(I0.75Br0.25)3 layers have significant downward band bending near PEDOT:PSS layers. Such downward band bending is unfavorable for hole selectivity and surface passivation at the interface. However, the addition of Sn powder to the tin perovskite precursor solution was found to significantly prevent the downward band bending and rather cause upward band bending, which can improve the hole selectivity and field-effect passivation quality. This can be due to prevented oxidation of perovskite layers by Sn powder addition. These findings are crucial for developing highly efficient and stable tin perovskite solar cells.

Stability of Cesium-Based Lead Halide Perovskites under UV Radiation.

Lead halide perovskites have been extensively studied for their potential applications, including photodetectors, solar cells, and high-energy radiation detection. These applications are possible because of their unique optoelectronic properties, such as tunable band gap, high optical absorption coefficient, and unique defect self-healing properties, which result in high defect tolerance. Despite these advantages, the long-term stability remains a critical issue that could hinder commercial applications of these materials. Reports on the stability of lead halide perovskites for optoelectronic applications have normally focused on methylammonium (MA)/formamidinium (FA), with very limited information for other systems, in particular, Cs-containing perovskites. In this paper, we report the stability of thick CsPbBr3-x Cl x polycrystalline thin films (∼8 μm) with several halide Br-Cl ratios after exposure to deep UV radiation. The chemical, crystal structure, optical, and electrical properties are analyzed, and the results are used to propose a degradation mechanism. The chemical analysis on the surface and bulk of the films indicates the formation of cesium oxide after UV exposure, with no significant change in the crystalline structure. The proposed mechanism explains the formation of cesium oxides during UV exposure. The I-V characteristics of diode structures also showed significant degradation after UV exposure, primarily at lower diode rectification ratios. The mechanism proposed in this paper can contribute to developing strategies to enhance the long-term stability of inorganic lead halide perovskites under UV exposure.

Enhanced structural and optical properties of Cs0.1FA0.9PbI3 perovskite thin film with potassium doping for perovskite solar cells

Hybrid halide perovskite (HHP) materials have been rigorously explored since last decade specially for their potential use as absorber layer material in perovskite solar cells. Formamidinium (FA) based HHP materials show many fascinating properties and exhibit thermal stability. However, photoactive cubic phase of formamidinium lead iodide (FAPbI3) material is unstable at room temperature. To overcome the phase stability issue, substitution of Cs+ or MA+ (methylamine) ion has been found useful. Further, to enhance the material properties of FA-MA or FA-Cs based HHP materials, alkali ion doping is widely explored. In this study, the role of K+ ion doping in enhancing the optoelectronic properties of Cs-FA based HHP material is studied thoroughly by structural and optical characterizations. The XRD results show the suppression of yellow non-perovskite phase after Cs doping in FAPbI3 material. The SEM results predict increased grain size with small K+ content in Cs0.1FA0.9PbI3 material. The PL and TRPL results predict the increase in radiative recombination and charge carrier lifetime with small K-doping and detrimental effects of doping concentration above 3 % of K. The solar cell simulation results yield a maximum power conversion efficiency of 18.21 % in K0.03(Cs0.1FA0.9)0.97PbI3 absorbing layer-based device.

Data-driven strategy for bandgap database construction of perovskites and the potential segregation study

Light-induced segregation limits the practical application of mixed halide perovskites in solar cells. Herein, halide segregation is evaluated by a data-driven approach with constructing a bandgap database of 53,361 mixed ABX3 [where A = Cs, formamidinium (FA) or methylammonium (MA); B = Pb or Sn; X = Br, Cl, or I] perovskites. A transfer learning strategy was employed to fine-tune the parameters of a Graph Neural Network model using experimental and density functional theory (DFT)-calculated bandgaps. This approach accelerated the construction of a unique database, distinguishing it from others primarily focused on ABX3 perovskite element substitution. The database is characterized by continuously varying compositions and accurate bandgaps. It was utilized to calculate the free energy of 20,688 mixed iodine-bromine perovskites and generate corresponding phase diagrams for predicting their light-induced segregation behavior. It is found that the bandgap increases with decreasing ionic radii at the A-site and X-site. This composition-dependent bandgap difference drives halide segregation. Moreover, using a higher Cs content at the A-site, rather than MA, reduces this bandgap difference, enhancing photostability. The proposed data-driven strategy can facilitate the targeted design of novel perovskites with mixed compositions and the investigation of halide perovskite segregation.

Composition Dictates Octahedral Tilt and Photostability in Halide Perovskites.

Halide perovskites are excellent candidate materials for use in solar cell, LED, and detector devices, in part because their composition can be tuned to achieve ideal optoelectronic properties. Empirical efficiency optimization has led the field toward compositions rich in FA (formamidinium) on the A-site and I on the X-site, with additional small amounts of MA (methylammonium) or Cs A-site cations and Br X-site anions. However, it is not clear how and why the specific compositions of alloyed, that is, mixed component, halide perovskites relate to photo-stability of the materials. Here, this work combines synchrotron grazing incidence wide-angle X-ray scattering, photoluminescence, high-resolution scanning electron diffraction measurements and theoretical modelling to reveal the links between material structure and photostability. Namely, this work finds that increased octahedral titling leads to improved photo-stability that is correlated with lower densities of performance-harming hexagonal polytype impurities. These results uncover the structural signatures underpinning photo-stability and can therefore be used to make targeted changes to halide perovskites, bettering the commercial prospects of technologies based on these materials.

Enhanced Charge Transfer in Quasi-2D Perovskite by Formamidinium Cation Gradient Incorporation for Efficient and Stable Solar Cells.

Quasi-2D perovskites have attracted much attention in perovskite photovoltaics due to their excellent stability. However, their photoelectric conversion efficiency (PCE) still lags 3D counterparts, particularly with high short-circuit current (JSC) loss. The quantum confinement effect is pointed out to be the sole reason, which introduces widened bandgap and poor exciton dissociation, and undermines the light capture and charge transport. Here, the gradient incorporation of formamidinium (FA) cations into quasi-2D perovskite is proposed to address this issue. It is observed that FA prefers to incorporate into the larger n value phases near the film surface compared to the smaller n value phases in the bulk, resulting in a narrow bandgap and gradient structure within the film. Through charge dynamic analysis using in situ light-dark Kelvin probe force microscopy and transient absorption spectroscopy, it is demonstrated that incorporating 10% FA significantly facilitates efficient charge transfer between low n-value phases in the bulk and high n-value nearby film surface, leading to reduced charge accumulation. Ultimately, the device based on (AA)2(MA0.9FA0.1)4Pb5I16, where AA represents n-amylamine renowned for its exceptional environmental stability as a bulky organic ligand, achieves an impressive power conversion efficiency (PCE) of 18.58% and demonstrates enhanced illumination and thermal stability.

Alloy [FA,Cs]PbI3 perovskite surfaces: The role of surface cesium composition in stability and tolerance to defect formation

Halide-perovskite alloys that include cesium have achieved records of stability and efficiency in solar cells. Controlling the surface composition, defects, and electronic properties guarantees interface stability and improves performance. By using density functional theory and molecular dynamic simulations, we analyzed which surface compositions of the formamidinium (FA) and cesium (Cs) lead iodide perovskite FA1−xCsxPbI3 with 25 and 50% of Cs become more stable than pure perovskites. Structural and electronic properties and tolerance to defect formation were also evaluated. Surface energy calculations show that only the alloys with 25% Cs and FAI-enriched surfaces are more stable than pure FAPbI3 ones. The most stable alloy surface shows electronic energy levels similar to the FAPbI3 perovskite, suggesting that this alloy may also be efficient for charge transport in the cell. However, the presence of Cs on the alloy surface, although low, favors the formation of FAI vacancies, which is detrimental to the stability of the perovskite. These results suggest evaluating FA1−xCsxPbI3 alloys with small Cs compositions to mitigate the formation of defects or using a passivation scheme. This study delivers valuable information for efficiency device improvement from the perspective of interface stability.

Significance of Formamidinium Incorporation in Perovskite Composition and Its Impact on Solar Cell Efficiency: A Mini‐Review

Perovskite solar cells (PSCs) have gained tremendous research interest recently owing to several advantages, including low material cost, facile solution processability, bandgap tunability, and alluring device efficiency. The organic formamidinium (FA) cation‐based perovskites are mainly considered as one of the potential candidates for charge carrier generation due to their excellent properties, such as bandgap and thermal stability than traditional perovskites. However, the inevitable unfavorable polymorphism (i.e., α to δ) at room temperature still forms the basis for numerous research works to allow the fabrication of a high‐quality absorber and enhances the PSCs performance. The studies to resolve the polymorphism and several contemporary techniques (e.g., passivation strategy) with several recent novel fabrication methods presented in this review form the essence of the improvements in PSCs. The absorber morphology also influences the charge‐transfer behavior and the device's lifetime. Therefore, understanding these properties is essential to improve the absorber quality and avoid many defects. This review focuses on the structure and properties of pure and mixed FA perovskites with various halides, mainly the FA cation's role in the absorber composition. And a comprehensive overview of recent FA cation‐based double, triple, and quadrupole PSCs results with proper scientific explanations to understand the device physics.

Iodine Modulates the MACl‐Assisted Growth of FAPbI3 for High Efficiency Perovskite Solar Cells

AbstractThe preferential growth of α‐phase formamidinium perovskite (α‐FAPbI3) at low temperatures can be achieved with the incorporation of chloride‐based additives, with methylammonium chloride (MACl) being the most common example. However, compared to other less‐volatile chloride additives, MACl only remains in the growing perovskite film for a short time before evaporating during annealing, primarily influencing the early stages of film formation. In addition, evaporation of MACl as methylamine (MA0) and HCl can introduce a side reaction between MA0 and formamidinium (FA), undermining the compositional purity and phase stability of α‐FAPbI3. In this study, it is demonstrated that addition of iodine (I2) into the FAPbI3 precursor solution containing MACl suppresses the MA‐FA side reaction during annealing. Additionally, MACl evaporation is delayed owing to strong interaction with triiodide. The added I2 facilitates spontaneous growth of α‐FAPbI3 prior to annealing, with an improved bottom morphology due to the formation of fewer byproducts. Perovskite solar cells derived from an I2‐incorporated solution deliver a champion power conversion efficiency of 25.2% that is attributed to suppressed non‐radiative recombination.

Solvent-Induced Bright Emission in Lead-Free Organic-Inorganic Antimony Bromides with Reversible Transformation.

Lead-free low-dimensional organic-inorganic metal halides have gained increasing attention in a wide range of applications due to their low toxicity, outstanding optical performance, and structural tunability. In this work, a general method of incorporating organic molecule into sodium antimony bromides is introduced. The 1D Na3SbBr6(C2H6OS)6 and Na3SbBr6(C4H8OS)6 single crystals exhibit bright yellow and orange emission with PL peaks at 610 and 664nm, and high photoluminescence quantum yields (PLQYs) of 85% and 60%, respectively. These two compounds can be reversibly converted into each other by the removal and addition of the organic components. Their exceptional luminescent performance enables them to be used as solid-state phosphors for the fabrication of yellow and orange down-conversion LEDs. A white LED with a high color rendering index (CRI) of 95 is also fabricated by using Na3SbBr6(C2H6OS)6 as the yellow phosphor. The universality of this method is demonstrated by synthesizing other members of this family with diverse A-groups, including methylammonium (MA) and formamidinium (FA). This work provides an effective strategy for the development of diverse lead-free and high-performance organic-inorganic hybrid materials and indicates these organic-inorganic hybrid compounds are promising luminescent materials for lighting or displays.

Boosting optoelectronic performance of (FA)X(MA)1-XPbI3 perovskite solar cells: Via FAI post-treatment engineering

Complex composition engineering of mixed-cations perovskite (FAxMA1-xPbI3) has recently supported rapid progress in perovskite solar cells (PSCs). Nevertheless, it is insufficient to embed and accommodate formamidinium (FA) cation into the MAPbI3 lattice structure via existing methods, leaving behind masses of FA or lead halide content and deteriorating photovoltaic performance. Herein, we present facile surface engineering via post-treated methodology, the surface of CH3NH3PbI3 (MAPbI3) films post-treated with formamidinium iodide (FAI) solution and that results get mixed-cation FAxMA1-xPbI3 perovskite films. The mixed-cation-based FAXMA1-XPbI3 perovskite with significant and large grain size, uniform and compact morphology, highly crystallization, and consequently reducing defect density of the perovskite films can be produced via the present method. It is observed that the film, post-treated with FAI-2, shows results in a very stable and highly crystalline lattice structure with attributes such as extended carrier lifetime, better electron transport, and decreased defect density. The optimized device demonstrates a promising power conversion efficiency (PCE) of 21.89%, and higher than that of the non-treated (19.08%) devices. Furthermore, the devices based on the novel FAI-post-treatment engineering exhibit significantly enhanced stability compared to non-treated devices. Therefore, this approach provides a novel methodology that offers a simple method for producing superior mixed perovskite films, potentially paving the way for the future exploitation of the boosted performance of perovskite solar cells.

Strain‐Induced α‐Phase Stabilization for Low Dark Current FAPI‐Based Photodetectors

AbstractFormamidinium lead iodide (FAPbI3) has gained considerable interest as a promising photoactive layer for optoelectronic devices due to its broad spectrum of light absorption and increased thermal stability when compared to its conventional methylammonium counterpart (MAPbI3). Recent developments in substituting formamidinium (FA) with smaller Cs cations have further accelerated its growth in the photovoltaic (PV) community by enhancing phase stability and power conversion efficiency (PCE). However, only a few studies are reported on perovskite photodetectors (PPDs). Here, the influence of Cs incorporation is investigated on PD performance in the CsXFA1‐XPbI3 system (X = 0–0.25). Finding that the partial substitution of FA with Cs cations alleviates lattice strain by increasing crystallinity and inducing a well‐ordered surface morphology with vertical crystallographic orientation, which suppresses non‐radiative recombination mechanisms. Such improved physicochemical properties of the mixed‐cation perovskite light absorbers can improve the PD performance by reducing the dark and noise current to values as low as 3.3 × 10−9 A cm−2 and 6.1 × 1011 A Hz−1/2, thereby enabling PPDs with a faster photoresponse and greater sensitivity, which holds great promise for future optoelectronics applications.