Formamidinium Lead Iodide Perovskite Research Articles

Formamidinium lead iodide perovskite photovoltaics with MoS2 quantum dots

We present the formation of a composite film made out of formamidinium lead iodide (FAPI) and molybdenum disulphide quantum dots (MoS2 QDs) and propose a corresponding photovoltaic device architecture based on a ‘type-I’ alignment of the two materials’ electronic energy levels. The introduction of the MoS2 QDs has not compromised the overall crystallinity of the FAPI film and the composite absorber has shown improved stability. We report on the benefits of this composite film and energy band arrangement as the photogenerated carriers in MoS2 QDs, both positive and negative, are injected into the FAPI host matrix, resulting in an increased current density of 24.19 mA cm−2 compared to a current density of 19.83 mA cm−2 for the control device with FAPI only. The corresponding photoconversion efficiency increases from 12.6 to 15.0%. We also show that inclusion of MoS2 QDs in FAPI films resulted in a notable improvement in the fill factor and open-circuit voltage of the solar cells. Most importantly, MoS2 QDs enhanced the film stability by reducing defect formation and acting as passivating agents that minimize recombination losses and improve charge carrier transport. Our results suggest that a composite film in a type-I device architecture can introduce benefits for both future developments in perovskite solar cells and effectively tackling the longstanding challenges of carrier transport in QDs solar cells.

Lattice Strain Regulation and Halogen Vacancies Passivation Enable High-Performance Formamidine-Based Perovskite Solar Cells.

Formamidinium lead iodide (FAPbI3) perovskite has lately surfaced as the preferred contender for highly proficient and robust perovskite solar cells (PSCs), owing to its favorable bandgap and superior thermal stability. Nevertheless, volatilization and migration of iodide ions (I-) result in non-radiating recombination centers, and the presence of large formamidine (FA) cations tends to cause lattice strain, thereby reducing the power conversion efficiency (PCE) and stability of PSCs. To solve these problems, the lead formate (PbFa) is added into the perovskite solution, which effectively mitigates the halogen vacancy and provides tensile strain outside the perovskite lattice, thereby enhancing its properties. The strong coordination between the C═O of HCOO- and Pb-I backbones effectively immobilizes anions, significantly increases the energy barrier for anion vacancy formation and migration, and reduces the risk of lead ion (Pb2+) leakage, thereby improving the operation and environmental safety of the device. Consequently, the champion PCE of devices with Ag electrodes can be increased from 22.15% to 24.32%. The unencapsulated PSCs can still maintain 90% of the original PCE even be stored in an N2 atmosphere for 1440h. Moreover, the target devices have significantly improved performance in terms of light exposure, heat, or humidity.

Stable FAPbI3 Perovskite Solar Cells via Alkylammonium Chloride-Mediated Crystallization Control.

α-Phase formamidinium lead iodide (FAPbI3) perovskite solar cells (PSCs) have garnered significant attention, owing to their remarkable efficiency. Methylammonium chloride (MACl), a common additive, is used to control the crystallization of FAPbI3, thereby facilitating the formation of the photoactive α-phase. However, MACl's high volatility raises concerns regarding its stability and potential impact on the stability of the device. In this study, we partially substituted MACl with n-propylammonium chloride (PACl), which has a long alkyl chain, to promote the oriented crystallization of FAPbI3, ultimately forming an δ-phase-free perovskite. The FAPbI3 film containing PACl demonstrates an enhanced photoluminescence intensity and lifetime. Additionally, PACl's presence at grain boundaries acts as a protective layer for the PSCs. Consequently, we achieved a power conversion efficiency (PCE) of 22.4% and exceptional stability. It maintains over 95% of initial PCE for 100 days in an N2 glovebox, over 85% after 100 h of maximum power point tracking, and over 80% after 60 °C thermal aging.

Elimination of Intragrain Defect to Enhance the Performance of FAPbI3 Perovskite Solar Cells by Ionic Liquid.

Ionic liquids have been widely used to improve the efficiency and stability of perovskite solar cells (PSCs), and are generally believed to passivate defects on the grain boundaries of perovskites. However, few studies have focused on the relevant effects of ionic liquids on intragrain defects in perovskites which have been shown to be critical for the performance of PSCs. In this work, the effect of ionic liquid 1-hexyl-3-methylimidazolium iodide (HMII) on intragrain defects of formamidinium lead iodide (FAPbI3) perovskite is investigated. Abundant {111}c intragrain planar defects in pure FAPbI3 grains are found to be significantly reduced by the addition of the ionic liquid HMII, shown by using ultra-low-dose selected area electron diffraction. As a result, longer charge carrier lifetimes, higher photoluminescence quantum yield, better charge carrier transport properties, lower Urbach energy, and current-voltage hysteresis are achieved, and the champion power conversion efficiency of 24.09% is demonstrated. These observations suggest that ionic liquids significantly improve device performance resulting from the elimination of {111}c intragrain planar defects.

Close-Space Sublimation as a Scalable Method for Perovskite Solar Cells.

Vacuum techniques for perovskite photovoltaics (PV) are promising for their scalability but are rarely studied with techniques readily adaptable for industry. In this work, we study the use of close-space sublimation (CSS) for making perovskite solar cells, a technique that has seen widespread use in industry, including in PV, and benefits from high material-transfer and low working pressures. A pressed pellet of formamidinium iodide (FAI) can be used multiple times as an organic source, without needing replacement. Using CSS at a rough vacuum (10 mbar), efficient cesium formamidinium lead iodide perovskite based solar cells are obtained reaching a maximum photoconversion efficiency (PCE) of 18.7%. They maintain their performance for >650 h when thermally stressed at 85 °C in a nitrogen environment. To explain the initial rise in PCE upon heating, we used drift-diffusion simulations and identified a reduction in bulk trap density as the primary factor.

Multifunctional sulfonium-based treatment for perovskite solar cells with less than 1% efficiency loss over 4,500-h operational stability tests

The stabilization of grain boundaries and surfaces of the perovskite layer is critical to extend the durability of perovskite solar cells. Here we introduced a sulfonium-based molecule, dimethylphenethylsulfonium iodide (DMPESI), for the post-deposition treatment of formamidinium lead iodide perovskite films. The treated films show improved stability upon light soaking and remains in the black α phase after two years ageing under ambient condition without encapsulation. The DMPESI-treated perovskite solar cells show less than 1% performance loss after more than 4,500 h at maximum power point tracking, yielding a theoretical T80 of over nine years under continuous 1-sun illumination. The solar cells also display less than 5% power conversion efficiency drops under various ageing conditions, including 100 thermal cycles between 25 °C and 85 °C and an 1,050-h damp heat test.

ZnO/SnO2 bilayer electron transport layer strategy to improve the performance of FAPbI3 solar cell

In recent years, organic–inorganic hybrid perovskite (PVK) devices have attracted widespread attention with their high absorption coefficient and low-cost fabrication process. Formamidinium lead iodide (FAPbI3) perovskite solar cells (PSCs) have been reported to obtain high power conversion efficiencies (PCEs) due to the narrow bandgap. Zinc oxide (ZnO) has better electrical conductivity and high transmittance than tin (IV) dioxide (SnO2). However, the deprotonation behavior of ZnO limits its use in formamidinium (FA) or methylammonium (MA) devices, so it is mostly used in all-inorganic PSCs. In this work, to avoid the deprotonation behavior of ZnO, we prepared FAPbI3 PSCs using ZnO/SnO2 as bilayer electron transporting layers (ETLs), which improved the conductivity of the ETLs and promoted electron extraction and transfer. In addition, the decrease in the oxygen vacancy (Ov) on the bilayer ETLs contributed to the suppression of the non-radiative recombination of the device, thus enabling the achievement of a higher fill factor. As a result, the modified ETLs increased the PCE of FAPbI3 PSCs from 20.24% to 21.42% and improved the stability of the devices. The PCE of unpackaged devices increased steadily to 21.91% when stored in an N2 atmosphere for 183 days.

Triple-junction perovskite-perovskite-silicon solar cells with power conversion efficiency of 24.4.

The recent tremendous progress in monolithic perovskite-based double-junction solar cells is just the start of a new era of ultra-high-efficiency multi-junction photovoltaics. We report on triple-junction perovskite-perovskite-silicon solar cells with a record power conversion efficiency of 24.4%. Optimizing the light management of each perovskite sub-cell (∼1.84 and ∼1.52 eV for top and middle cells, respectively), we maximize the current generation up to 11.6 mA cm-2. Key to this achievement was our development of a high-performance middle perovskite sub-cell, employing a stable pure-α-phase high-quality formamidinium lead iodide perovskite thin film (free of wrinkles, cracks, and pinholes). This enables a high open-circuit voltage of 2.84 V in a triple junction. Non-encapsulated triple-junction devices retain up to 96.6% of their initial efficiency if stored in the dark at 85 °C for 1081 h.

Operando spectroscopic characterization of formamidinium lead iodide perovskite quantum dots for tracking electrochemical reactions

Multidimensional ABX3 hybrid perovskites three-dimensionally confined dot-shaped structure demonstrate versatile potential to photoelectrochemical cells for water splitting, hydrogen generation, solar cells, and light-emitting diodes. To apply perovskite quantum dots (PQDs) to solar-driven chemistry and optoelectronic devices, understanding the photoinduced charge carrier dynamics of PQDs under electrochemical conditions or applied bias are important. In this study, the detailed transformation mechanism of formamidinium lead iodide perovskite quantum dots under electrochemical conditions was studied by tracking the products of the reaction through cyclic voltammetry, X-ray photoemission spectroscopy, in-situ UV–visible spectroelectrochemistry, etc. Through comprehensive characterizations, the mechanism of irreversible oxidative transformation of perovskite quantum dots was presented. This study provides deeper insight into the electrochemical behavior of PQDs for successful solar-driven chemistry and optoelectronic device applications.

Deciphering Reaction Products in Formamidine-Based Perovskites with Methylammonium Chloride Additive.

The fabrication of formamidinium lead iodide (FAPbI3) perovskite solar cells (PSCs) involves the addition of methylammonium chloride (MACl) to promote low-temperature α-phase formation and grain growth. However, as the added MACl deprotonates and volatilizes into methylamine (MA0) and HCl for removal, MA0 can chemically interact with formamidinium (FA+), forming methyl formamidinium (MFA+) as a byproduct. Despite its significance, the chemical interactions among FAPbI3 perovskites, MACl additives, and their byproducts remain poorly understood. Our findings reveal that the FA+ and MA0 reaction primarily yields a mixture of cis/trans-N-methyl formamidinium iodide (MFAI) isomers, with cis-MFAI prevailing as the dominant species. Moreover, MFAI subsequently reacts with PbI2 to yield fully formed cis-MFAPbI3 2H-phase perovskite. We elucidated the effects of MFAI on the crystal growth, phase stability, and band gap of formamidine-based perovskites through the growth of single crystals. This research offers valuable insights into the role of these byproducts in influencing the efficiency and long-term stability of future PSCs.

Role of compressive and tensile strains and spin-orbit coupling on structure and behaviors of cubic FAPbI3 perovskites: A first-principles prediction

Organic-inorganic perovskite materials have attracted significant attention in solar technologies due to their extraordinary structural, electrical, and optical features. This study extensively examined the impacts of bidirectional tensile and compressive strains and spin-orbit coupling (SOC) on the structural, electronic and optical characteristics of formamidinium lead iodide perovskite (FAPbI3) structures. The investigation was performed using the first-principles density-functional theory (DFT). The electronic band structures of FAPbI3 without SOC revealed that the perovskite structure possesses the characteristics of a semiconductor, explicitly featuring a direct bandgap. The application of compressive strains resulted in dwindling the electronic bandgap while tensile strains upsurged the bandgaps, except at +6 % strains. The incorporation of the SOC subjugated a notable decrease in the bandgap, causing a transition of the perovskite structure from a direct bandgap to an indirect bandgap state. The real dielectric constant suggested that the system maintains its semiconducting character under the exposure of both compressive and tensile strains. The imaginary part of the dielectric function, loss spectrum, and absorption coefficient peaks of FAPbI3 perovskites exhibited a blueshift when subjected to compressive strains. However, the application of tensile strains eventuated in a redshift. The electronic and optical characteristics indicated that FAPbI3 perovskites have great potential for optoelectronic devices, including LEDs, LCD backlights, solar cells, lasers, and light detectors.

Enhancing perovskite solar cell performance through dynamic hydrogen-mediated polarization of nitrogen and sulfur in phthalocyanine

Perovskite defect passivation has been researched extensively as an essential technique to improve the efficiency and stability of perovskite solar cells (PSCs) and thus drive their future commercialization. Three phthalocyanines named NP-SC6-ZnPc, NP-SC6-CuPc, and NP-SC6-H2Pc were synthesized and use for PSCs passivation. Theoretical calculations and experimental verifications confirmed that NP-SC6-H2Pc had the best passivation effect on perovskites. The phthalocyanine ring’s central hydrogen atoms are transferred dynamically from NP-SC6-H2Pc and interact with the formamidinium lead iodide (FAPbI3) perovskite through nitrogen-hydrogen bonding, resulting in α-FAPbI3 perovskite formation and increasing the sulfur/nitrogen (S/N) passivation capability. FAPbI3-based PSCs treated with NP-SC6-H2Pc demonstrated the highest power conversion efficiency (PCE) of 24.03 % (certified PCE of 23.78 %) with excellent stability. This significant finding represents the first observation of dynamic transfer of the hydrogen atoms in phthalocyanine and provides a thorough investigation of the perovskite passivation mechanism.

Lattice Strain Regulation Enables High-Performance Formamidinium Perovskite Photovoltaics.

Formamidinium lead iodide (FAPbI3 ) perovskite possesses an ideal optical bandgap and is a potential material for fabricating the most efficient single-junction perovskite solar cells (PSCs). Nevertheless, large formamidinium (FA) cations result in residual lattice strain, which reduces the power conversion efficiency (PCE) and operational stability of PSCs. Herein, the modulation of lattice strain in FAPbI3 crystals via a π-conjugated organic amine, i.e., 4-pyrene oxy butylamine (PYBA), is proposed. PYBA pairs at the grain boundary serve as a template for the crystallization of FAPbI3 perovskite, thereby inducing a highly oriented crystal and a pure α-phase film. The PYBA pairs with strong π-π interactions provide a solid fulcrum for external compression strain, thus compensating for the inherent tension strain of FAPbI3 crystals. The strain release elevates the valence band of the perovskite crystals, thereby decreasing the bandgap and trap density. Consequently, the PYBA-regulated FAPbI3 PSC achieves an excellent PCE of 24.76%. Moreover, the resulting device exhibits improves operational stability and maintains over 80% of its initial PCE after 1500h under maximum power point tracking conditions.

Strain Engineering Toward High‐Performance Formamidinium‐Based Perovskite Solar Cells

The power conversion efficiency (PCE) of organic–inorganic halide perovskite solar cells (PSCs) has increased rapidly in recent years, with the certified best perovskite single‐junction photovoltaics reaching an astounding PCE of 26%. Formamidine (FA)‐based perovskites possess excellent photovoltaic properties and superior thermal stability, establishing them as one of the most promising perovskite materials for light absorption. However, the issue of the phase instability of black‐phase formamidinium lead iodide (α‐FAPbI3) perovskite has seriously impeded its commercialization process, with the strain found in perovskite films being regarded as a significant factor impacting the stability of PSCs. This article begins by examining the sources of strain and the characterization techniques related to perovskites. Subsequently, it outlines the effects of strain on FA‐based perovskites and presents strategies to modify lattice strain. Finally, the potential for strain engineering in the future is discussed. This review aims to clarify the impact of strain on FA‐based perovskite, determine potential methods of strain engineering to enhance device performance, and ultimately facilitate the commercialization of these materials.

Atomistic Understanding of the Coherent Interface Between Lead Iodide Perovskite and Lead Iodide

AbstractMetal halide perovskite semiconductors have shown great performance in solar cells, and including an excess of lead iodide (PbI2) in the thin films, either as mesoscopic particles or embedded domains, often leads to improved solar cell performance. Atomic resolution scanning transmission electron microscope micrographs of formamidinium lead iodide (FAPbI3) perovskite films reveal the FAPbI3:PbI2 interface to be remarkably coherent. It is demonstrated that such interface coherence is achieved by the PbI2 deviating from its common 2H hexagonal phase to form a trigonal 3R polytype through minor shifts in the stacking of the weakly van‐der‐Waals‐bonded layers containing the near‐octahedral units. The exact crystallographic interfacial relationship and lattice misfit are revealed. It is further shown that this 3R polytype of PbI2 has similar X‐ray diffraction (XRD) peaks to that of the perovskite, making XRD‐based quantification of the presence of PbI2 unreliable. Density functional theory demonstrates that this interface does not introduce additional electronic states in the bandgap, making it electronically benign. These findings explain why a slight PbI2 excess during perovskite film growth can help template perovskite crystal growth and passivate interfacial defects, improving solar cell performance.

Laser Derived Electron Transport Layers with Embedded p-n Heterointerfaces Enabling Planar Perovskite Solar Cells with Efficiency over 25.

Electron transport layers (ETLs) with pronounced electron conducting capability are essential for high performance planar perovskite photovoltaics, with the great challenge being that the most widely used metal oxide ETLs unfortunately have intrinsically low carrier mobility. Herein is demonstrated that by simply addressing the carrier loss at particle boundaries of TiO2 ETLs, through embedding in ETL p-n heterointerfaces, the electron mobility of the ETLs can be boosted by three orders of magnitude. Such embedding is encouragingly favorable for both inhibiting the formation of rutile phase TiO2 in ETL, and initiating the growth of high-quality perovskite films with less defect states. By virtue of these merits, creation of formamidinium lead iodide perovskite solar cells (PSCs) with a champion efficiency of 25.05% is achieved, setting a new benchmark for planar PSCs employing TiO2 ETLs. Unencapsulated PSCs deliver much-improved environmental stability, i.e., more than 80% of their initial efficiency after 9000 h of air storage under RH of 40%, and over 90% of their initial efficiency at maximum power point under continuous illumination for 500 h. Further work exploring other p-type nanocrystals for embedding warrants the proposed strategy as a universal alternative for addressing the low-carrier mobility of metal oxide based ETLs.

Oriented nucleation in formamidinium perovskite for photovoltaics.

The black phase of formamidinium lead iodide (FAPbI3) perovskite shows huge promise as an efficient photovoltaic, but it is not favoured energetically at room temperature, meaning that the undesirable yellow phases are always present alongside it during crystallization1-4. This problem has made it difficult to formulate the fast crystallization process of perovskite and develop guidelines governing the formation of black-phase FAPbI3 (refs. 5,6). Here we use in situ monitoring of the perovskite crystallization process to report an oriented nucleation mechanism that can help to avoid the presence of undesirable phases and improve the performance of photovoltaic devices in different film-processing scenarios. The resulting device has a demonstrated power-conversion efficiency of 25.4% (certified 25.0%) and the module, which has an area of 27.83 cm2, has achieved an impressivecertified aperture efficiency of 21.4%.

Electronic structures and molecular dynamics of gadolinium-doped FAPbI3 perovskite crystals

The additive effect of a gadolinium ion into a formamidinium lead iodide (FAPbI3) perovskite crystal on electronic structures and molecular dynamics was investigated for improving photovoltaic performance with stability. The electronic structures, band structure, partial density of state, and molecular dynamics were determined by first-principles calculation. The band distribution and charge transfer between the 5d orbital of the gadolinium atom, the 5p orbital of the iodine atom, and the 6p orbital of the lead atom promoted the carrier generation and diffusion related to short-circuit current density. The enthalpy and kinetic energy prompted stabilization of the gadolinium-doped crystal with a slight distortion of coordination structure, as compared with the decomposition of the FAPbI3 crystal. Diffusion coefficients of iodine and lead ions in the FAPbI3 crystal with defect were increased, predicting decomposition. The gadolinium-doped FAPbI3 perovskite crystal has great potential for applications in photovoltaic devices by improving photovoltaic performance.

Simulation Analysis of Formamidinium Lead Iodide Perovskite Solar Cells as Function of Thickness and Defects of Absorber Layer, Hole and Electron Transport Layer Under SCAPS-1D

Simulation Analysis of Formamidinium Lead Iodide Perovskite Solar Cells as Function of Thickness and Defects of Absorber Layer, Hole and Electron Transport Layer Under SCAPS-1D

Fully Methylammonium-Free Stable Formamidinium Lead Iodide Perovskite Solar Cells Processed under Humid Air Conditions.

Fabricating perovskite solar cells (PSCs) in ambient air condition is beneficial for lowering the processing cost and boosting the commercialization. Formamidinium lead iodide (FAPbI3) is an attractive candidate for efficient PSCs; however, it easily suffers from degradation and phase transition in the presence of ambient moisture. Methylammonium (MA) cation is commonly incorporated to stabilize FAPbI3, whereas the residual MA tends to deteriorate the thermal and operational stability. Herein, we report a MA-free strategy to fabricate high-quality α-FAPbI3 films and inverted PSCs under open air conditions with a relative humidity (RH) of 60 ± 10%. The incorporation of phenylethylammonium iodide (PEAI) effectively inhibits the decomposition and phase transition of FAPbI3 during its crystallization in humid air. Accordingly, phase-pure α-FAPbI3 perovskite films with significantly reduced δ-FAPbI3 and PbI2 content are successfully obtained. In addition, introducing PEAI strongly enhances the crystallinity of FAPbI3 perovskite films, thereby yielding enlarged grain sizes and reduced grain boundaries. Defects at the grain boundaries and surface are further passivated by PEAI addition, so that the trap state density is significantly decreased. As a result, the non-radiative recombination is effectively suppressed and the charge carrier transport is promoted. The inverted device optimized with a suitable PEAI concentration exhibits an enhanced power conversion efficiency (PCE) of 17.83%, which significantly surpasses the control device (12.29% PCE). Moreover, the PEAI optimized FAPbI3 PSCs demonstrate strongly improved long-term stability, with nearly 97% PCE maintained after 27-day storage under ambient conditions. This work provides a feasible way to fabricate PSCs in ambient air for promoting their wide range of applications.