Li-ion Flux Research Articles

Dendrite Growth and Dead Lithium Formation in Lithium Metal Batteries and Mitigation Using a Protective Layer: A Phase-Field Study.

Lithium metal batteries (LMBs) are considered one of the most promising next-generation rechargeable batteries due to their high specific capacity. However, severe dendrite growth and subsequent formation of dead lithium (Li) during the battery cycling process impede its practical application. Although extensive experimental studies have been conducted to investigate the cycling process, and several theoretical models were developed to simulate the Li dendrite growth, there are limited theoretical studies on the dead Li formation, as well as the entire cycling process. Herein, we developed a phase-field model to simulate both electroplating and stripping process in a bare Li anode and Li anode covered with a protective layer. A step function is introduced in the stripping model to capture the dynamics of dead Li. Our simulation clearly shows the growth of dendrites from a bare Li anode during charging. These dendrites detach from the bulk anode during discharging, forming dead Li. Dendrite growth becomes more severe in subsequent cycles due to enhanced surface roughness of the Li anode, resulting in an increasing amount of dead Li. In addition, it is revealed that dendrites with smaller base diameters detach faster at the base and produce more dead lithium. Meanwhile, the Li anode covered with a protective layer cycles smoothly without forming Li dendrite and dead Li. However, if the protective layer is fractured, Li metal preferentially grows into the crack due to enhanced Li-ion (Li+) flux and forms a dendrite structure after penetration through the protective layer, which accelerates the dead Li formation in the subsequent stripping process. Our work thus provides a fundamental understanding of the mechanism of dead Li formation during the charging/discharging process and sheds light on the importance of the protective layer in the prevention of dead Li in LMBs.

Trinitarian Design of Gradient Artificial Interphase Enables Colossal Granular Li Deposits for Stable Li-Metal Batteries.

The cycling lifespan of Li-metal batteries is compromised by the unstable solid electrolyte interphase (SEI) and the continuous Li dendrites, restricting their practical implementations. Given these challenges, establishing an artificial SEI holds promise. Herein, a trinitarian gradient interphase is innovatively designed through composite coatings of magnesium fluoride (MgF2), N-hexadecyltrimethylammonium chloride (CTAC), and polyvinylidene fluoride-hexafluoropropylene copolymer (PVDF-HFP) on Li-metal anode (LMA). Specifically, the MgF2/CTAC/PVDF-HFP SEI spontaneously forms a lithium fluoride (LiF)-rich PVDF-HFP-based SEI, along with lithium-magnesium (Li-Mg) alloy substrate as lithiophilic electronic conductor and positively charged CTAC during plating. Noticeably, the Li-Mg alloy homogenizes the distribution of electric field and reduce the internal resistance, while the electronically insulated LiF/PVDF-HFP composite SEI offers fast ion-conducting and mechanical flexibility, accommodating the volumetric expansion and ensuring stable Li-ion flux. Additionally, CTAC at the dendritic tip is pivotal for mitigating dendrites through its electrostatic shield mechanism. Innovatively, this trinitarian synergistic mechanism, which facilitates colossal granular Li deposits, constructs a dendrite-free LMA, leading to stable cycling performances in practical Li||LFP, popular Li||NCM811, and promising Li||S full cells. This work demonstrates the design of multifunctional composite SEI for comprehensive Li protection, thereby inspiring further advancements in artificial SEI engineering for alkali-metal batteries.

Lithiophilic Protective Dual Layer Enabling Stable Electrodeposition of Lithium at High Current Density

Lithium (Li) is an ideal anode material for rechargeable batteries and thus manufacturing Li metal is crucial for the practical development of Li metal batteries. Electrodeposition is an efficient technique for producing ultrathin and scalable Li metal electrodes. However, the dendritic growth and the side reactions of Li with electrolyte during the electrodeposition are the main obstacles to overcome. In this study, we designed a pre-coated protective dual layer (PDL) composed of a poly(ethylene oxide)-based solid polymer electrolyte (SPE) and a polydopamine-coated cellulose membrane (PD-CM). The adhesive and ion-conductive SPE layer suppressed the growth of Li dendrites and side reactions with liquid electrolyte. The PD-CM layer with high porosity and lithiophilicity promoted a facile and uniform Li-ion flux. By applying the pre-coated PDL, Li was uniformly electrodeposited on the Ag-coated Cu at a high current density of 6 mA cm−2. The Li/LiFePO4 cell composed of an electrodeposited Li anode with PDL and a LiFePO4 cathode was assembled without an additional separator, and its cycling performance was evaluated. The cell initially delivered a high discharge capacity of 154.8 mAh g−1 at 45 °C and exhibited excellent cycling stability with a capacity retention of 97.0% after 200 cycles.

Recent advances in functionalized separator for dendrites‐free and stable lithium metal batteries

AbstractLithium (Li) metal anode is considered the “Holy grail” for the most promising next‐generation rechargeable lithium metal batteries (LMBs) because of ultra‐high theoretical specific capacity, ultra‐low reduction potential and small density. However, uncontrolled lithium dendrite growth and inevitable side reaction seriously hindered the application of practical LMBs because of the deteriorating electrochemical performances and exacerbating the safety issues of LMBs. Thus, improving the electrochemical performances of LMBs by constructed of functionalized separator is promising for overcoming the above‐mentioned challenges due to its' significantly advantages, such as enhancing mechanical and thermal stability, regulating the diffusion and migration of Li ions, homogenizing Li ion flux, forming protective layer on Li anode surfaces, etc. The relational investigations have significantly increased since 2020, while the comprehensive reviews on this research direction are relatively rare, especially in the detailed mechanism aspects. In this review, an overview in functionalized separator for stable LMBs is discussed in detail. Firstly, the current issues of LMBs are in‐depth discussion and the general strategies are summarized. Subsequently, the requirements and limitations of separator, as well as the advantages of functionalized separator are summarized and reviewed. Most importantly, the protection mechanisms and research advances of advanced functionalized separator are comprehensively discussed and summarized. Furthermore, the applications of functionalized separator in rechargeable lithium metal‐based full cells are reviewed. Finally, the challenges and potential opportunities for the future development and rational design of functionalized separator are highlighted in rechargeable LMBs to obtain future research directions related to the significant strategy of constructing dendrite‐free and stable LMBs.

A Homogeneous Janus Membrane Based on Functionalized MOFs Crosslinked by Aramid Nanofibers for Quasi-Solid-State Lithium Sulfur Batteries.

Lithium-sulfur batteries (LSBs) are considered as promising candidates in the next generation of high energy density devices. However, the serious shuttle effect, irreversible dendrite growth of Li metal anode, and the potential safety hazard impede the practical application of LSBs. Herein, a novel homogeneous Janus membrane based on functionalized MOFs crosslinked by aramid nanofibers is designed and synthesized to simultaneously solve the above challenges in quasi-solid-state LSBs. The aramid nanofibers with good mechanical properties and thermal stability act as a homogeneous scaffold to crosslink the MOF particles with different ligands on both sides and this Janus membrane upgrades the stability and safety on both the cathode and anode. Specifically, the amino ligand-decorated MOFs contribute to homogenize Li-ion flux and stabilize the lithium anode, and the sulfonic ligand-decorated MOFs effectively suppress the shuttle effect by the dual effects of chemical adsorption and electrostatic repulsion. The quasi-solid-state LSBs assembled with this homogeneous Janus membrane deliver excellent rate performance and cycling stability. Moreover, it exhibits a high initial capacity of 923.4 mAh g-1 at 1C at 70°C, and 697.3 mAh g-1 is retained after 100 cycles, indicating great potential for its application in high-safety LSBs.

Towards ultra-stable and dendrite-suppressed Li-metal batteries: Ion-regulating graphene-modified separators

The practical application of metallic lithium (Li) anodes is hindered by nonuniform Li deposition/dissolution, as well as poor electrochemical reversibility during cycling. To address these challenges, surface modification of polymer separators with functional materials has been extensively explored. In this study, two distinct surface-modifying layers composed of MnOx and polydopamine (PDA) are applied to modify the surface of graphene-coated polypropylene separators (G@PP). Both MnOx and PDA, which are formed through the graphene layer, significantly enhance the intrinsic electrolyte wettability of G@PP, resulting in a homogeneous Li-ion flux. Furthermore, the lithiophilic properties revealed by DFT and COMSOL analyses synergize with the hydrophilic characteristics, resulting in a more stable electrochemical performance in Li-metal batteries (LMBs). The enhanced electrolyte permeability of the coating layer allows Li–Cu cells with MnOx-modified graphene-coated PP (MG@PP) and PDA-modified graphene-coated PP (PG@PP) separators to exhibit significantly improved cycle stability compared with Li–Cu cells with G@PP separators. Interestingly, Li–S cells equipped with MG@PP and PG@PP separators exhibit also enhanced electrochemical performance compared with Li–S cells with G@PP separators. These results highlight that surface engineering of separator-coating materials along with hydrophilic and lithiophilic materials enhances both long-term cycle stability and electrochemical kinetics in LMBs.

Quasi-Gel Polymer Electrolyte Interfaced with Electrodes through Solvent-Swollen Poly(ethylene oxide) for High-Performance Lithium/Lithium-Ion Batteries.

Solid polymer electrolytes (SPEs) are regarded as a superior alternative to traditional liquid electrolytes of lithium-ion batteries (LIBs) due to their improved safety features. The practical implementation of SPEs faces challenges, such as low ionic conductivity at room temperature (RT) and inadequate interfacial contact, leading to high interfacial resistance across the electrode and electrolyte interfaces. In this study, we addressed these issues by designing a quasi-gel polymer electrolyte (QGPE), a blend of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), poly(ethylene oxide) (PEO), and succinonitrile (SN), with the desired mechanical strength, ionic conductivity, and interfacial stability through a simple solution casting technique. The QGPE features a thin solvated PEO layer on its surface, which wets the electrode, reducing the interfacial resistance and ensuring a homogeneous Li-ion flux across the interface. The optimized QGPE exhibits a good lithium-ion conductivity of 1.14 × 10-3 S cm-1 with a superior lithium-ion transference number of 0.7 at 25 °C. The Li/QGPE/Li symmetric cell exhibits a highly reversible lithium plating/stripping process for over 1300 h with minimal voltage polarization of ∼20 mV. The Li/QGPE/LiFePO4 full cell demonstrates good rate capability and excellent long-term cycling performance at a 0.1 C rate at 25 °C, maintaining a specific discharge capacity of 148 mAh g-1 over 200 cycles. The effectiveness of QGPE for LIBs is proven using a graphite/QGPE/LiFePO4 4 × 4 cm pouch cell, showcasing outstanding flexibility and tolerance against intentional abuse.

2D Metal-Oxide Nanosheets as a Homogeneous Li-Ion Flux Regulator for High-Performance Anodeless Lithium Metal Batteries.

The anodeless battery design has recently gained significant interest by eliminating the direct use of a thick lithium (Li) foil. However, it suffers from inhomogeneous Li+ flux, resulting in dendrite growth and a short cycling life. To address this, the exfoliation of layered-structure titanium oxide to 2D nanosheets (2DTiOx) is proposed to precisely control Li+ flux at the atomic scale by maximizing Li+ affinitive Ti sites. Compared to cells without these nanosheets, the Li|2DTiOx|Cu half-cell demonstrates stable cyclability over 900 cycles, with a Coulombic efficiency (CE) over 99% at 0.5 mA cm-2 and 0.5 mAh cm-2. Similarly, a long stable cycling life over 1500 h at 1.0-3.0 mA cm-2 is observed for a 2DTiOx-based symmetric cell containing a limited Li amount from electrodeposited Li metal (e-Li|2DTiOx|e-Li). The full cells (e-Li|2DTiOx||NCM811 and e-Li|2DTiOx||LFP) coupled with NCM811 and LFP cathodes showed a long cycle life of 400 cycles at 1.0 C and 0.5 C, respectively. The exceptional battery performance is attributed to the uniform Li disposition on the 2DTiOx electrode, emphasizing the crucial role of the exposed basal plane in 2DTiOx as an efficient atomic scale Li+ flux regulator. This strategy is expected to advance next-generation lithium metal batteries (LMBs) by highlighting the significance of Li+ affinity at the Ti sites of 2DTiOx nanosheets.

Functional Protective Coatings Based on Polysaccharides and Single-Ion Conducting Polymers for Li Metal Batteries

This work aims to study a protective coating based on cellulose and P(LiMTFSI) single-ion conductor polymer and its effects on Li metal anode stability and reversibility. The strategy used involves the physical mixture of the aforementioned polymers to enhance the electrochemical performance through Li-ion flux homogenization at the Li metal surface, promoting the formation of a dense plating. Single-ion conducting polymers (SICPs) are incorporated due to their beneficial effects such as enhancing lithium ion transport, boosting lithium transference number (𝑡𝐿𝑖 +), and diminishing the effects of concentration polarization, avoiding the initiation and propagation of high surface area lithium (HSAL). Furthermore, a quasi-solid-state Li metal battery system is explored which brings additional advantages over the typically used organic electrolytes. In this sense, during this study we propose using the protective coating based on cellulose and P(LiMTFSI) to tailor an adequate interphase that creates a good adhesion, by taking advantage of the polymers film formation ability, and therefore improving the lifespan and safety of the battery. The coating effectiveness is tested by casting the solution on an activated lithium surface and performing lithium platting/stripping protocols in Li/Li and Li/Cu pouch cells under selected current densities (0.5, 1 and 2 mA/cm2). Complementary electrochemical tests are carried out to study transport, conductivity parameters, and its performance in full cell coupled with LFP cathode. Finally, we analyze the correlation with the physicochemical properties and electrochemical performed based on spectroscopic techniques and microscopy to study the most relevant parameters influencing a high Coulombic Efficiency. Acknowledgments This work has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska – Curie Grant Agreement N° 945357, and co-financing from the Slovenian Research and Innovation Agency (ARIS) is fully acknowledged.

A Ceramic/Lithiophilic Metal Dual Protective Layer for Stable Lithium Metal Anodes Fabricated via Transfer-Printing Methods

Lithium metal has attracted researcher’s attention because of its superior theoretical capacity (3860mAh g-1 or 2061 mAh cm-3), which is nearly 10 times higher than commercialized anode materials, for example, graphite (372 mAh g-1). However, lithium metal is not currently used in commercial lithium metal batteries due to safety and efficiency issues that arise during long-term battery operation. The high reactivity of lithium metal causes almost all available electrolytes to be spontaneously reduced on the Li surface to form a solid-electrolyte interface (SEI) layer. Unfortunately, this passivating SEI layer is typically too fragile to withstand significant mechanical deformation of the electrode during cycling, resulting in crack formation. These cracks expose fresh Li underneath, which locally enhances Li-ion flux and promotes morphological deformation of the lithium metal surface. This often leads to dendritic Li deposition that can cause internal short circuits and compromise battery safety. Additionally, repeated failures and repairs of SEIs result in the continued loss of both Li and electrolyte, leading to low coulombic efficiency (CE) and rapid capacity decrease.To mitigate these problems, researchers have attempted to suppress lithium dendrite growth by slurry coating on the lithium metal surface such as ceramic layer and lithiophilic metal. These materials and conventional lithium metal protection coating methods partially inhibit the growth of lithium dendrites; however, they come with several significant drawbacks. The ceramic layer possesses high mechanical properties that physically inhibit the growth of lithium dendrites. However, it exhibits poor interfacial characteristics with lithium metal, leading to increased resistance. This heightened resistance results in the formation of uneven lithium deposition layers at high current densities, causing cracks in the ceramic layer. Lithiophilic metals exhibit an advantage in reducing nucleation resistance through alloying reactions with lithium prior to nucleation, thereby facilitating uniform lithium ion deposition. However, their low mechanical properties limit their potential for enhancing electrochemical performance. Furthermore, the conventional coating method used for lithium metal protection involves the direct application of solvent-containing slurries onto the lithium metal surface using slurry coating techniques. Given the inherent reactivity of lithium metal, the presence of residual moisture and impurities within the solvent may induce sub-reactions, ultimately compromising the stability of lithium metal.In this study, we propose an approach to improve the cycling stability of lithium metal through Ceramic/lithiophilic metal dual protective layer fabricated via transfer-printing methods. The dual lithium metal protection layer, consisting of Ceramic/lithiophilic, involves coating a lithiophilic metal layer between the ceramic layer and the lithium metal. This method aims to maximize electrochemical performance improvement through a synergistic effect that utilizes the high mechanical properties of ceramics and solves the problem of interfacial resistance between the ceramic layer and lithium metal through the lithiophilic metal. Furthermore, we propose a coating process for lithium metal protection layers using a method based on transfer printing. This method involves applying pressure to the lithium metal surface through transfer printing of pre-finished composite protective layers on a film, rather than directly applying slurry onto the lithium metal surface. Transfer printing offers the advantage of maintaining the stability of lithium metal by avoiding direct application of slurry onto the lithium metal surface, thereby ensuring the integrity of the protection layer.

Robust and Adhesive Laminar Solid Electrolyte with Homogenous and Fast Li-Ion Conduction for High-Performance All-Solid-State Lithium Metal Battery.

Constructing composite solid electrolytes (CSEs) integrating the merits of inorganic and organic components is a promising approach to developing high-performance all-solid-state lithium metal batteries (ASSLMBs). CSEs are now capable of achieving homogeneous and fast Li-ion flux, but how to escape the trade-off between mechanical modulus and adhesion is still a challenge. Herein, a strategy to address this issue is proposed, that is, intercalating highly conductive, homogeneous, and viscous-fluid ionic conductors into robust coordination laminar framework to construct laminar solid electrolyte with homogeneous and fast Li-ion conduction (LSE-HFC). A 9µm-thick LSH-HFC, in which poly(ethylene oxide)/succinonitrile is adsorbed by coordination laminar framework with metal-organic framework nanosheets as building blocks, is used here as an example to determine the validity. The Li-ion transfer mechanism is verified and works across the entire LSE-HFC, which facilitates homogeneous Li-ion flux and low migration energy barriers, endowing LSE-HFC with high ionic conductivity of 5.62×10-4Scm-1 and Li-ion transference number of 0.78 at 25°C. Combining the outstanding mechanical strength against punctures and the enhanced adhesion force with electrodes, LSE-HFC harvests uniform Li plating/stripping behavior. These enable the realization of high-energy-density ASSLMBs with excellent cycling stability when being assembled as LiFePO4/Li and LiNi0.6Mn0.2Co0.2O2/Li cells.

Lithiophilic Multichannel Layer to Simultaneously Control the Li-Ion Flux and Li Nucleation for Stable Lithium Metal Batteries.

Although the Li metal has been gaining attention as a promising anode material for the next-generation high-energy-density rechargeable batteries owing to its high theoretical specific capacity (3860 mAh g-1), its practical use remains challenging owing to inherent issues related to Li nucleation and growth. This paper reports the fabrication of a lithiophilic multichannel layer (LML) that enables the simultaneous control of Li nucleation and growth in Li-metal batteries. The LML, composed of lithiophilic ceramic composite nanoparticles (Ag-plated Al2O3 particles), is fabricated using the electroless plating method. This LML provides numerous channels for a uniform Li-ion diffusion on a nonwoven separator. Furthermore, the lithiophilic Ag on the Li metal anode surface facing the LML induces a low overpotential during Li nucleation, resulting in a dense Li deposition. The LML enables the LiNi0.8Co0.1Mn0.1O2|| Li cells to maintain a capacity higher than 75% after 100 cycles, even at high charge/discharge rates of 5.0 C at a cutoff voltage of 4.4 V, and achieve an ultrahigh energy density of 1164 Wh kg-1. These results demonstrate that the LML is a promising solution enabling the application of Li metal as an anode material in the next-generation Li-ion batteries.

Rational design of polymer-based insulating scaffolds for high-capacity lithium metal batteries

Lithium metal is a promising anode material for next-generation high-energy–density secondary batteries. However, the uncontrolled growth of Li dendrites leads to infinite volume expansion and poor cycling stability. Herein, we propose a designable insulating polydopamine (PDA)-coated porous polytetrafluoroethylene (PTFE) scaffold. A porous PTFE (pPTFE) scaffold with micron-sized pores was fabricated, which provided bottom-up Li deposition owing to its insulating nature. Furthermore, the PDA-coated porous PTFE (PDA-pPTFE) scaffold provided internal space for Li growth and homogenized the Li-ion flux with abundant polar functional groups in the PDA, enabling “bottom-up” Li deposition within the scaffold without dendrite growth. This uniquely designed scaffold demonstrated excellent performance in half and symmetric cells with a small voltage hysteresis and dendrite-free Li plating. Moreover, when coupled with high-loading NCM cathodes (∼4 mA h cm−2), the PDA-pPTFE-based full cells exhibited stable cycling and rate performance, even with a low NP ratio of 1.0 at a rate of 1/3C, and exhibited a high energy density of 801 W h L−1. These results indicated the potential of the PDA-pPTFE scaffold as an anode material for highly stable next-generation rechargeable batteries.

The chemo-mechanics of initiation of crack advance in Niobium Tungsten Oxide single crystals due to delithiation

Niobium tungsten oxide (NWO) micron-sized single crystals show promise as the active particles in the anodes of lithium ion batteries due to their fast charge/discharge and high storage capabilities. Within the “block” phases such as Nb16W5O55, Nb14W3O44 and the HNb2O5 polymorph, Li ion diffusion occurs in a unidirectional manner along a single axis of the crystal and lithiation/delithiation results in significant length changes in this direction. A chemo-mechanics analysis is developed for delithiation of an NWO “block” phase single crystal that contains a pre-existing flaw in the form of a through-thickness edge crack. Galvanostatic delithiation occurs by the flux of Li ions through the free ends of the crystal and also through the faces of the crack, with concomitant shrinkage of the surface layer over a depth equal to that of the crack. The induced tensile stress in the surface layer can be of sufficient magnitude to advance the crack in the NWO crystal, consistent with recent experimental observations for Nb14W3O44. A 2D full-field finite element version of the chemo-mechanics model is used to explore the sensitivity of cracking to crack length, delithiation rate of the anode, diffusivity of Li ions within the NWO single crystal storage particle and to the kinetics of Li ion transfer across the particle surface-electrolyte interface. Additionally, a simplified, lumped parameter model is developed by assuming that the Li ion occupancy is spatially uniform in a surface layer that extends to a depth of the pre-existing crack, and has a spatially uniform but different value than that of the underlying core of the particle. This simplified model can be expressed as a set of first order differential equations in time and gives the main features of delithiation and the associated transient stress state in the single crystal. Both the full model and the lumped parameter version predict that crack advance from a pre-existing defect is triggered by a high delithiation rate, consistent with the experimental literature.

A Large-Scale Fabrication of Flexible, Ultrathin, and Robust Solid Electrolyte for Solid-State Lithium-Sulfur Batteries.

All-solid-state lithium metal batteries (ASSLMBs) are considered as the most promising candidates for the next-generation high-safety batteries. To achieve high energy density in ASSLMBs, it is essential that the solid-state electrolytes (SSEs) are lightweight, thin, and possess superior electrochemical stability. In this study, a feasible and scalable fabrication approach to construct 3D supporting skeleton using an electro-blown spinning technique is proposed. This skeleton not only enhances the mechanical strength but also hinders the migration of Li-salt anions, improving the lithium-ion transference number of the SSE. This provides a homogeneous distribution of Li-ion flux and local current density, promoting uniform Li deposition. As a result, based on the mechanically robust and thin SSEs, the Li symmetric cells show outstanding Li plating/stripping reversibility. Besides, a stableinterfacecontact between SSE and Li anode has been established with the formation of an F-enriched solid electrolyte interface layer. The solid-state Li|sulfurized polyacrylonitrile (Li|SPAN) cell achieves a capacity retention ratio of 94.0% after 350 cycles at 0.5 C. Also, the high-voltage Li|LCO cell shows a capacity retention of 92.4% at 0.5 C after 500 cycles. This fabrication approach for SSEs is applicable for commercially large-scale production and application in high-energy-density and high-safety ASSLMBs.

Dynamic physical network constructed by tripartite H-bonds in artificial SEI to shape ultra-long life dendrite-free lithium-metal anodes

Constructing artificial solid electrolyte interfaces (SEIs) to shape dendrite-free lithium (Li)-metal anodes remains challenges. Herein, we designed dynamic physical network (DPN) with abundant lithiophilic/anionphilic groups through tripartite hydrogen bonds (H-bonds), serving as artificial SEIs in high-loading NCM811-Li metal batteries. The formation and dissociation of DPN endowed by tripartite H-bonds under tension release during Li plating/stripping cycling skillfully balance the contradiction between mechanical robustness and deformability. LiO bonds between lithiophilic sites and Li ions, and extra H-bonds between hydroxyl and electrolyte anions, endow DPN with functions of homogenizing Li-ion flux and accelerating its desolvation, synergistically achieving the uniform Li-ion deposition and weakening the charge shielding. The artificial SEI enhanced Li-anode (DPN@Li) withstood repeated Li ions plating/stripping processes for over 1000 h, which is 5 times longer than pure Li-anodes, and maintained low overpotential at a high current density of 10 mA cm−2. DPN@Li-based NCM811 full cells deliver high specific capacities and outstanding cycle life over 3000 cycles. Further, DPN@Li possesses excellent electrochemical performance in the high active material loading (7.84 mg cm−2) and foldable pouch cells. This work provides a conceptual framework of DPN constructed by multiple weak intermolecular interaction for artificial SEI to shape anode performance, and achieves the idea with a facile manner and simple chemical substances to promote practical applications of LMBs.

5.1µm Ion-Regulated Rigid Quasi-Solid Electrolyte Constructed by Bridging Fast Li-Ion Transfer Channels for Lithium Metal Batteries.

An ultra-thin quasi-solid electrolyte (QSE) with dendrite-inhibiting properties is a requirement for achieving high energy density quasi-solid lithium metal batteries (LMBs). Here, a 5.1µm rigid QSE layer is directly designed on the cathode, in which Kevlar (poly(p-phenylene terephthalate)) nanofibers (KANFs) with negatively charged groups bridging metal-organic framework (MOF) particles are served as a rigid skeleton, and non-flammable deep eutectic solvent is selected to be encapsulated into the MOF channels, combined with in situ polymerization to complete safe electrolyte system with high rigidness and stability. The QSE withconstructed topological network demonstrates high rigidity (5.4GPa), high ionic conductivity (0.73 mS cm-1 at room temperature), good ion-regulated properties, and improved structural stability, contributing to homogenized Li-ion flux, excellent dendrite suppression, and prolonged cyclic performance for LMB. Additionally, ion regulation influences the Li deposition behavior, exhibiting a uniform morphology on the Li-metal surface after cycling. According to density-functional theory, KANFs bridging MOFs as hosts play a vital function in the free-state and fast diffusion dynamics of Li-ions. This work provides an effective strategy for constructing ultrathin robust electrolytes with a novel ionic conduction mode.

A Star-StructuredPolymer Electrolyte for Low-Temperature Solid-State Lithium Batteries.

Solid-state polymer lithium metal batteries (SSLMBs) have attracted considerable attention because of their excellent safety and high energy density. However, the application of SSLMBs is significantly impeded by uneven Li deposition at the interface between solid-state electrolytes and lithium metal anode, especially at a low temperature. Herein, this issue is addressed by designing an agarose-based solid polymer electrolyte containing branched structure. The star-structured polymer is synthesized by grafting poly (ethylene glycol) monomethyl-ether methacrylate and lithium 2-acrylamido-2-methylpropanesulfonate onto tannic acid. The star structure regulates Li-ion flux in the bulk of the electrolyte and at the electrolyte/electrodeinterfaces. This unique omnidirectional Li-ion transportation effectively improves ionic conductivity, facilitates a uniform Li-ion flux, inhibits Li dendrite growth, and alleviates polarization. As a result, a solid-state LiFePO4||Li battery with the electrolyte exhibits outstanding cyclability with a specific capacity of 134 mAh g-1 at 0.5C after 800 cycles. The battery shows a high discharge capacity of 145 mAh g-1 at 0.1 C after 200 cycles, even at 0°C. The study offers a promising strategy to address the uneven Li deposition at the solid-state electrolyte/electrode interface, which has potential applications in long-life solid-state lithium metal batteries at a low temperature.

Regulating lithium nucleation and deposition on carbon cloth decorated with vertically aligned Ag-doped MnO2 nanosheet arrays for dendrite-free lithium metal anode

Metallic Li with high specific capacity and low electrode potential is considered as the most promising anode material. The main obstacles to its application are uncontrollable Li dendrites growth and infinite volume changes. Herein, we design a modified carbon cloth (CC) by vertically aligned MnO2 nanosheet arrays embedded with tiny Ag (Ag/MnO2@CC) through hydrothermal approach. Density functional theory (DFT) calculations indicate that MnO2 and Ag show a more negative adsorption energy (−4.31 and −2.34 eV) than C (−1.65 eV), implying their better lithiophilicity. Finite element simulations demonstrate that the Ag-doped MnO2 nanosheet arrays reduce local current density and redistribute Li-ion flux. Moreover, the channels assembled by vertical-aligned MnO2 nanosheets and 3D CC can offer sufficient spaces to buffer volume fluctuation during cycling. Accordingly, the Ag/MnO2@CC is employed as a lithiophilic host to supervise homogenous Li nucleation and deposition. The Ag/MnO2@CC electrodeposited with Li exhibits dendrite-free feature and a high Coulombic efficiency of 99.9% during 300 cycles. The symmetric cell shows an ultra-low polarization voltage of 14 mV over 1300 h at 1 mA cm−2 with the capacity of 1 mAh cm−1. The full cell paired with LiFePO4 exhibits excellent capacity of 105.5 mAh g−1 after 400 cycles at 1 C.

Artificial Li3N SEI-Enforced Stable Cycling of Li Powder Composite Anode in Carbonate Electrolytes

Lithium metal is considered one of the most attractive anode materials for next-generation batteries. However, the practical application of rechargeable Li-metal batteries has been hindered by the uncontrollable growth of Li dendrites and large volume changes during electrochemical cycling, leading to low Coulombic efficiency and safety concerns. This study reports a facile process of printing copper nitride nanowires (Cu3N NWs) onto Li metal powder (LMP) composite anode surface via a roll-pressing technique. Cu3N readily reacts with Li to form lithium nitride (Li3N), which is regarded as an excellent component for the interfacial layer on Li metal. The Li3N layer possesses a high ionic conductivity and ensures a homogeneous Li-ion flux, resulting in the suppression of dendrites. As a result, Li/Li symmetric cells assembled with the Li3N-LMP electrode exhibited lower overpotentials and superior cycling performance. Furthermore, NCM622/Li3N-LMP full cells demonstrated better capacity retention behavior (over 90% after 250 cycles) and higher discharge capacities during rate capability tests compared to the bare LMP cell. This study highlights the importance of a rational design of interfacial layers on LMP anodes for stable and long-term cycling.