Fluorescent Polystyrene Research Articles

Influence of graphene oxide on the transport and deposition behaviors of colloids in saturated porous media

The effects of graphene oxide (GO) on the transport and deposition behaviors of colloids with different sizes in packed quartz sand were investigated in both NaCl (10 and 50 mM) and CaCl2 solutions (1 and 5 mM) at pH 6. Fluorescent carboxylate-modified polystyrene latex microspheres (CMLs) with size ranging from 0.2 to 2 μm were utilized as model colloids. Both breakthrough curves and retained profiles of colloids in the presence and absence of GO in suspensions under all examined solution conditions were analyzed. The breakthrough curves of all three different-sized CMLs with GO were higher yet the retained profiles were lower than those without GO at both examined ionic strengths in NaCl solutions. The observation showed that GO increased the transport and decreased the deposition of all three different-sized CMLs in NaCl solutions. However, in CaCl2 solutions, opposite observation was achieved at two different ionic strength conditions. Specifically, the presence of GO increased the transport and decreased the deposition of all three different-sized CMLs in 1 mM CaCl2 solutions, whereas, it decreased the transport and increased the deposition of all three different-sized CMLs in 5 mM CaCl2 solutions. Comparison the breakthrough curves and retained profiles of CMLs versus those of GO yielded that the overall transport and deposition behaviors of all three different-sized CMLs with GO copresent in suspensions agreed well with the transport and deposition behaviors of GO under all examined conditions. The transport and deposition behaviors of CMLs in packed porous media clearly were controlled by those of GO under the conditions investigated in present study due to the adsorption of CMLs onto GO surfaces. Our study showed that once released into natural environment, GO would adsorb (interact with) different types of colloids and thus have significant influence on the fate and transport of colloids in porous media.

An assessment of the importance of exposure routes to the uptake and internal localisation of fluorescent nanoparticles in zebrafish (Danio rerio), using light sheet microscopy

A major challenge in nanoecotoxicology is finding suitable methods to determine the uptake and localisation of nanoparticles on a whole-organism level. Some uptake methods have been associated with artefacts induced by sample preparation, including staining for electron microscopy. This study used light sheet microscopy (LSM) to define the uptake and localisation of fluorescently labelled nanoparticles in living organisms with minimal sample preparation. Zebrafish (Danio rerio) were exposed to fluorescent gold nanoparticles (Au NPs) and fluorescent polystyrene NPs via aqueous or dietary exposure. The in vivo uptake and localisation of NPs were investigated using LSM at different time points (1, 3 and 7 days). A time-dependent increase in fluorescence was observed in the gut after dietary exposure to both Au NPs and polystyrene NPs. No fluorescence was observed within gut epithelia regardless of the NP exposure route indicating no or limited uptake via intestinal villi. Fish exposed to polystyrene NPs through the aqueous phase emitted fluorescence signals from the gills and intestine. Fluorescence was also detected in the head region of the fish after aqueous exposure to polystyrene NPs. This was not observed for Au NPs. Aqueous exposure to Au NPs resulted in increased relative swimming distance, while no effect was observed for other exposures. This study supports that the route of exposure is essential for the uptake and subsequent localisation of nanoparticles in zebrafish. Furthermore, it demonstrates that the localisation of NPs in whole living organisms can be visualised in real-time, using LSM.

Investigation of transient dynamics of capillary assisted particle assembly yield

In this paper, the transient behavior of the particle assembly yield dynamics when switching from low yield to high yield deposition at different velocity and thermal regimes is investigated. Capillary force assisted particle assembly (CAPA) using colloidal suspension of green fluorescent 270nm diameter polystyrene beads was performed on patterned poly (dimethyl siloxane) substrates using a custom-built deposition setup. Two types of patterns with different trapping site densities were used to assess CAPA process dynamics and the influence of pattern density and geometry on the deposition yield transitions. Closely packed 300nm diameter circular pits ordered in hexagonal arrangement with 300nm pitch, and 2×2mm2 square pits with 2μm spacing were used. 2-D regular structures of the deposited particles were investigated by means of optical fluorescence and scanning electron microscopy. The fluorescence micrographs were analyzed using a custom algorithm enabling to identify particles and calculate efficiency of the deposition performed at different regimes. Relationship between the spatial distribution of particles in transition zone and ambient conditions was evaluated and quantified by approximation of the yield profile with a logistic function.

Design and development of an Electrostatic Screen Battery for Emission Control (ESBEC)

Current diesel particulate filters (DPFs) can effectively capture the exhaust particles, but they add to engine backpressure and accumulate particles during their operation, which results in the need to regenerate the DPFs by burning off the collected particles periodically. This regeneration results in aerosol emissions, especially in the 10–30 nm size range and contributes to ultrafine particle pollution. In this research, we designed and developed a prototype of a novel diesel exhaust control device: the Electrostatic Screen Battery for Emissions Control (ESBEC). The device features high particle collection efficiency without adding to the exhaust backpressure and without the need for thermal regeneration of the collected particles. The ESBEC consists of a series of metal mesh screens coated with a superhydrophobic substance and an integrated carbon fiber ionizer to charge the incoming particles. Multiple pairs of screens (e.g., 5 pairs) are arranged in a battery, in which one screen of each pair is supplied with high voltage, and the other is grounded, producing electrostatic field produced across the screens. The application of a superhydrophobic coating onto the screens allows easy removal of the collected particles using liquid without the need for thermal regeneration. The current prototypes of the device were tested with fluorescent polystyrene latex (PSL) particles of 0.2 and 1.2µm in size and at 25 and 105L/min sampling flow rates. The average collection efficiency was ~87% for 0.2µm and ~95% for 1.2µm PSL particles. In addition, the ESBEC was tested with actual diesel exhaust particles; here its performance was verified by visually inspecting deposition of particles on an after-filter with the device ON and OFF. In the next stages of this work, the ESBEC will be challenged with diesel exhaust at different mass concentrations and for different collection time periods.

Inherently fluorescent polystyrene microspheres for coating, sensing and cellular imaging

Commercially available polystyrene (PS) fluorescent microspheres are widely used in biological field for tracing, in vivo imaging and calibration of flow cytometry, among other applications. However, these particles do suffer from some drawbacks such as the leakage and photobleaching of organic dyes within them. In the present study, inherently fluorescent properties of PS based microspheres have been explored for the first time. Here we find that a simple chloromethylation reaction endows the polystyrene particles with inherent fluorescence without any subsequent conjugation of an external fluorophore. A possible mechanism for fluorescence is elucidated by synthesizing and investigating p-ethylbenzyl chloride, a compound with similar structure. Significantly, no photobleaching or leaking issues were observed owing to the stable structure of the microspheres. Chloromethylated PS (CMPS) microspheres can keep their perpetual blue fluorescence even in dry powder state making them attractive as a potential coating material. Furthermore, the chloromethyl groups on CMPS microspheres make them very convenient for further functionalization. Poly(ethylene glycol) (PEG) grafted microspheres showed good biocompatibility and negligible cytotoxicity, and could be used to image intracellular Fe3+ due to the selective fluorescence quenching effect of aqueous Fe3+ in cytoplasm.

Phase mask-based multimodal superresolution microscopy.

We demonstrate a multimodal superresolution microscopy technique based on a phase masked excitation beam in combination with spatially filtered detection. The theoretical foundation for calculating the focus from a non-paraxial beam with an arbitrary azimuthally symmetric phase mask is presented for linear and two-photon excitation processes as well as the theoretical resolution limitations. Experimentally this technique is demonstrated using two-photon luminescence from 80 nm gold particle as well as two-photon fluorescence lifetime imaging of fluorescent polystyrene beads. Finally to illustrate the versatility of this technique we acquire two-photon fluorescence lifetime, two-photon luminescence, and second harmonic images of a mixture of fluorescent molecules and 80 nm gold particles with > 120 nm resolution (λ/7). Since this approach exclusively relies on engineering the excitation and collection volumes, it is suitable for a wide range of scanning-based microscopies.

Continuous sheathless microparticle and cell patterning using CL-SSAWs (conductive liquid-based standing surface acoustic waves)

We present continuous, sheathless microparticle patterning using conductive liquid (CL)-based standing surface acoustic waves (SSAWs). Conventional metal electrodes patterned on a piezoelectric substrate were replaced with electrode channels filled with a CL. The device performance was evaluated with 5-μm fluorescent polystyrene particles at different flow rate and via phase shifting. In addition, our device was further applied to continuous concentration of malaria parasites at the sidewalls of the fluidic channel.

Experimental study on two-photon fluorescence and coherent anti-Stokes Raman scattering microscopy

Two-photon excitation fluorescence (2PEF) and coherent anti-Stokes Raman scattering (CARS) are both third-order nonlinear optical processes, but for a long time, the true relationship and differences between them are not clearly understood. For decades, the second harmonic generation has been studied in conjunction with two-photon excitation fluorescence, so it was thought that the latter was a second-order nonlinear optical process. In order to make the two nonlinear interaction processes clear enough, the two nonlinear interaction processes are worthy to study at the same time. In this paper, firstly, we give the relationships between the 2PEF, CARS signal and their third-order nonlinear susceptibility, respectively; secondly, we use our own near infrared super-continuum CARS microscopy system to study both processes. In doing so, we describe the relationship between their third-order nonlinear susceptibility and the signal. The reconstructed images derived from CARS and those derived from 2PEF differ significantly when imaging the same 1.01 $\muup$m fluorescence polystyrene beads. If the lateral spatial resolution of the CARS imaging system is larger than the fluorescence polystyrene beads, the measured size cannot be used to calculate the real spatial resolution of the CARS system. However, the resolution of the 2PEF microscopy system can be obtained through the de-convolution of the 2PEF image, which is approximately equivalent to the current resolution of the CARS imaging system, which is measured using 280 nm polystyrene beads. The images of 280 nm polystyrene beads and 190 nm fluorescent polystyrene beads also exhibit differences between the two samples and the environment around them, respectively. This means that although CARS and 2PEF are both third-order nonlinear optical processes, they have their own properties. In particular, CARS is a third-order nonlinear optical oscillation process which is caused by the phasing match condition, but 2PEF is not influenced by the phasing match condition. The phase matching condition is responsible for the differences around the sample in the images of the 280 nm pure polystyrene beads, but not for the 190 nm fluorescent polystyrene beads. The de-convolution results for the 1.01 $\muup$m fluorescence polystyrene beads and the 280 nm pure polystyrene beads are very similar, so we can use the de-convolution results for 2PEF by the 1.01 $\muup$m fluorescence polystyrene beads to approximate the current measure condition and the resolution of the CARS imaging system. If we want to gain a more accurate resolution from the CARS imaging system, the spherical sample should be smaller than the lateral spatial resolution of this system.

Spectral reading of optical resonance-encoded cells in microfluidics.

The ability to label individual cells is useful for single-cell-level studies of complex cellular interactions and heterogeneity. Optically readable cell labeling is attractive as it can be investigated non-invasively and repeatedly at high speeds. Here, we demonstrate the feasibility of large-scale cell barcoding and identification using fluorescent polystyrene microbeads loaded into cells. Intracellular beads with different diameters in a range of 5 to 12 μm generate spectrally distinguished features or barcodes. A microfluidic chip was used to measure fluorescence resonance peaks emitted from individual cells. An algorithm comparing the peak wavelengths to a reference barcode library allowed barcode identification with high accuracy. This work provides a guideline to increase the number of unique identifiers and reduce various false-positive and false-negative errors.

Inertial Focusing of Microparticles in Curvilinear Microchannels.

A passive, continuous and size-dependent focusing technique enabled by “inertial microfluidics”, which takes advantage of hydrodynamic forces, is implemented in this study to focus microparticles. The objective is to analyse the decoupling effects of inertial forces and Dean drag forces on microparticles of different sizes in curvilinear microchannels with inner radius of 800 μm and curvature angle of 280°, which have not been considered in the literature related to inertial microfluidics. This fundamental approach gives insight into the underlying physics of particle dynamics and offers continuous, high-throughput, label-free and parallelizable size-based particle separation. Our design allows the same footprint to be occupied as straight channels, which makes parallelization possible with optical detection integration. This feature is also useful for ultrahigh-throughput applications such as flow cytometers with the advantages of reduced cost and size. The focusing behaviour of 20, 15 and 10 μm fluorescent polystyrene microparticles was examined for different channel Reynolds numbers. Lateral and vertical particle migrations and the equilibrium positions of these particles were investigated in detail, which may lead to the design of novel microfluidic devices with high efficiency and high throughput for particle separation, rapid detection and diagnosis of circulating tumour cells with reduced cost.

Manipulation and Immobilization of a Single Fluorescence Nanosensor for Selective Injection into Cells.

Manipulation and injection of single nanosensors with high cell viability is an emerging field in cell analysis. We propose a new method using fluorescence nanosensors with a glass nanoprobe and optical control of the zeta potential. The nanosensor is fabricated by encapsulating a fluorescence polystyrene nanobead into a lipid layer with 1,3,3-trimethylindolino-6′-nitrobenzopyrylospiran (SP), which is a photochromic material. The nanobead contains iron oxide nanoparticles and a temperature-sensitive fluorescent dye, Rhodamine B. The zeta potential of the nanosensor switches between negative and positive by photo-isomerization of SP with ultraviolet irradiation. The positively-charged nanosensor easily adheres to a negatively-charged glass nanoprobe, is transported to a target cell, and then adheres to the negatively-charged cell membrane. The nanosensor is then injected into the cytoplasm by heating with a near-infrared (NIR) laser. As a demonstration, a single 750 nm nanosensor was picked-up using a glass nanoprobe with optical control of the zeta potential. Then, the nanosensor was transported and immobilized onto a target cell membrane. Finally, it was injected into the cytoplasm using a NIR laser. The success rates of pick-up and cell immobilization of the nanosensor were 75% and 64%, respectively. Cell injection and cell survival rates were 80% and 100%, respectively.

Microplastics affect assimilation efficiency in the freshwater amphipod Gammarus fossarum.

An important issue in assessing microplastics is whether this newly emerging type of pollution affects freshwater invertebrates. This study was designed to examine the interactions between the amphipod Gammarus fossarum and two types of microplastics. To determine the ingestion and egestion of polyamide (PA) fibres (500×20μm), amphipods were exposed to four concentrations (100, 540, 2680, 13,380 PA fibrescm-2 base area of glass beakers) and four exposure times (0.5, 2, 8, 32h) as well as four post-exposure times (1, 2, 4, 16h). We demonstrate a positive correlation between concentration and ingestion of PA fibres. Fibres were found in the gut after 0.5h of exposure. Egestion was rapid and the digestive tract was empty 16h after exposure ended. To investigate whether polystyrene (PS) beads (1.6μm) can be taken up in the epithelial cells of the gut and the midgut glands, four concentrations (500, 2500, 12,500, 60,000 PS beadsmL-1) were tested. Cryosections exhibited fluorescent PS beads only within the gut lumen. In a 28-day feeding experiment with both, fibres and beads, we studied the amphipod's feeding rate, assimilation efficiency and wet weight change. The exposure to PA fibres (2680 PA fibrescm-2 base area of glass beakers) significantly reduced the assimilation efficiency of the animals. While both tested polymer types are ingested and egested, PA fibres can impair the health and ecological functions of freshwater amphipods under continuous exposure.

Charge-based separation of particles and cells with similar sizes via the wall-induced electrical lift.

The separation of particles and cells in a uniform mixture has been extensively studied as a necessity in many chemical and biomedical engineering and research fields. This work demonstrates a continuous charge-based separation of fluorescent and plain spherical polystyrene particles with comparable sizes in a ψ-shaped microchannel via the wall-induced electrical lift. The effects of both the direct current electric field in the main-branch and the electric field ratio in between the inlet branches for sheath fluid and particle mixture are investigated on this electrokinetic particle separation. A Lagrangian tracking method based theoretical model is also developed to understand the particle transport in the microchannel and simulate the parametric effects on particle separation. Moreover, the demonstrated charge-based separation is applied to a mixture of yeast cells and polystyrene particles with similar sizes. Good separation efficiency and purity are achieved for both the cells and the particles.

Nonlinear deformation and localized failure of bacterial streamers in creeping flows.

We investigate the failure of bacterial floc mediated streamers in a microfluidic device in a creeping flow regime using both experimental observations and analytical modeling. The quantification of streamer deformation and failure behavior is possible due to the use of 200 nm fluorescent polystyrene beads which firmly embed in the extracellular polymeric substance (EPS) and act as tracers. The streamers, which form soon after the commencement of flow begin to deviate from an apparently quiescent fully formed state in spite of steady background flow and limited mass accretion indicating significant mechanical nonlinearity. This nonlinear behavior shows distinct phases of deformation with mutually different characteristic times and comes to an end with a distinct localized failure of the streamer far from the walls. We investigate this deformation and failure behavior for two separate bacterial strains and develop a simplified but nonlinear analytical model describing the experimentally observed instability phenomena assuming a necking route to instability. Our model leads to a power law relation between the critical strain at failure and the fluid velocity scale exhibiting excellent qualitative and quantitative agreeing with the experimental rupture behavior.

Enhanced detection with spectral imaging fluorescence microscopy reveals tissue- and cell-type-specific compartmentalization of surface-modified polystyrene nanoparticles

BackgroundPrecisely targeted nanoparticle delivery is critically important for therapeutic applications. However, our knowledge on how the distinct physical and chemical properties of nanoparticles determine tissue penetration through physiological barriers, accumulation in specific cells and tissues, and clearance from selected organs has remained rather limited. In the recent study, spectral imaging fluorescence microscopy was exploited for precise and rapid monitoring of tissue- and cell-type-specific distribution of fluorescent polystyrene nanoparticles with chemically distinct surface compositions.MethodsFluorescent polystyrene nanoparticles with 50–90 nm diameter and with carboxylated- or polyethylene glycol-modified (PEGylated) surfaces were delivered into adult male and pregnant female mice with a single intravenous injection. The precise anatomical distribution of the particles was investigated by confocal microscopy after a short-term (5 min) or long-term (4 days) distribution period. In order to distinguish particle-fluorescence from tissue autofluorescence and to enhance the detection-efficiency, fluorescence spectral detection was applied during image acquisition and a post hoc full spectrum analysis was performed on the final images.ResultsSpectral imaging fluorescence microscopy allowed distinguishing particle-fluorescence from tissue-fluorescence in all examined organs (brain, kidney, liver, spleen and placenta) in NP-treated slice preparations. In short-time distribution following in vivo NP-administration, all organs contained carboxylated-nanoparticles, while PEGylated-nanoparticles were not detected in the brain and the placenta. Importantly, nanoparticles were not found in any embryonic tissues or in the barrier-protected brain parenchyma. Four days after the administration, particles were completely cleared from both the brain and the placenta, while PEGylated-, but not carboxylated-nanoparticles, were stuck in the kidney glomerular interstitium. In the spleen, macrophages accumulated large amount of carboxylated and PEGylated nanoparticles, with detectable redistribution from the marginal zone to the white pulp during the 4-day survival period.ConclusionsSpectral imaging fluorescence microscopy allowed detecting the tissue- and cell-type-specific accumulation and barrier-penetration of polystyrene nanoparticles with equal size but chemically distinct surfaces. The data revealed that polystyrene nanoparticles are retained by the reticuloendothelial system regardless of surface functionalization. Taken together with the increasing production and use of nanoparticles, the results highlight the necessity of long-term distribution studies to estimate the potential health-risks implanted by tissue-specific nanoparticle accumulation and clearance.Electronic supplementary materialThe online version of this article (doi:10.1186/s12951-016-0210-0) contains supplementary material, which is available to authorized users.

Three-Dimensional Segmentation and Quantitative Measurement of the Aqueous Outflow System of Intact Mouse Eyes Based on Spectral Two-Photon Microscopy Techniques

PurposeTo visualize and quantify the three-dimensional (3D) spatial relationships of the structures of the aqueous outflow system (AOS) within intact enucleated mouse eyes using spectral two-photon microscopy (TPM) techniques.MethodsSpectral TPM, including two-photon autofluorescence (TPAF) and second-harmonic generation (SHG), were used to image the small structures of the AOS within the limbal region of freshly enucleated mouse eyes. Long infrared excitation wavelengths (930 nm) were used to reduce optical scattering and autofluorescent background. Image stacks were collected for 3D image rendering and structural segmentation. For anatomical reference, vascular perfusion with fluorescent-conjugated dextran (150 KDa) and trans-corneal perfusion with 0.1 μm fluorescent polystyrene beads were separately performed to identify the episcleral veins (EV) and the trabecular meshwork (TM) and Schlemm's canal (SC), respectively.ResultsThree-dimensional rendering and segmentation of spectral two-photon images revealed detailed structures of the AOS, including SC, collector channels (CC), and aqueous veins (AV). The collagen of the TM was detected proximal to SC. The long and short axes of the SC were 82.2 ± 22.2 μm and 6.7 ± 1.4 μm. The diameters of the CC averaged 25.6 ± 7.9 μm where they originated from the SC (ostia), enlarged to 34.1 ± 13.1 μm at the midpoint, and narrowed to 18.3 ± 4.8 μm at the junction of the AV. The diameter of the AV averaged 12.5 ± 3.4 μm.ConclusionsSpectral TPM can be used to reconstruct and measure the spatial relationships of both large and small AOS structures, which will allow for better understanding of distal aqueous outflow dynamics.

Manipulation and detection of single nanoparticles and biomolecules by a photonic nanojet.

Optical methods to manipulate and detect nanoscale objects are highly desired in both nanomaterials and molecular biology fields. Optical tweezers have been used to manipulate objects that range in size from a few hundred nanometres to several micrometres. The emergence of near-field methods that overcome the diffraction limit has enabled the manipulation of objects below 100 nm. A highly free manipulation with signal-enhanced real-time detection, however, remains a challenge for single sub-100-nm nanoparticles or biomolecules. Here we show an approach that uses a photonic nanojet to perform the manipulation and detection of single sub-100-nm objects. With the photonic nanojet generated by a dielectric microlens bound to an optical fibre probe, three-dimensional manipulations were achieved for a single 85-nm fluorescent polystyrene nanoparticle as well as for a plasmid DNA molecule. Backscattering and fluorescent signals were detected with the enhancement factors up to ∼103 and ∼30, respectively. The demonstrated approach provides a potentially powerful tool for nanostructure assembly, biosensing and single-biomolecule studies.

Strategies for Tailoring the Pore-Size Distribution of Virus Retention Filter Papers.

The goal of this work is to demonstrate how the pore-size distribution of the nanocellulose-based virus-retentive filter can be tailored. The filter paper was produced using cellulose nanofibers derived from Cladophora sp. green algae using the hot-press drying at varying drying temperatures. The produced filters were characterized using scanning electron microscopy, atomic force microscopy, and N2 gas sorption analysis. Further, hydraulic permeability and retention efficiency toward surrogate 20 nm model particles (fluorescent carboxylate-modified polystyrene spheres) were assessed. It was shown that by controlling the rate of water evaporation during hot-press drying the pore-size distribution can be precisely tailored in the region between 10 and 25 nm. The mechanism of pore formation and critical parameters are discussed in detail. The results are highly valuable for development of advanced separation media, especially for virus-retentive size-exclusion filtration.

Distribution of Systemically Administered Nanoparticles Reveals a Size-Dependent Effect Immediately following Cardiac Ischaemia-Reperfusion Injury.

Nanoparticles represent an attractive option for systemic delivery of therapeutic compounds to the heart following myocardial infarction. However, it is well known that physicochemical properties of nanoparticles such as size, shape and surface modifications can vastly alter the distribution and uptake of injected nanoparticles. Therefore, we aimed to provide an examination of the rapid size-dependent uptake of fluorescent PEG-modified polystyrene nanoparticles administered immediately following cardiac ischaemia-reperfusion injury in mice. By assessing the biodistribution of nanoparticles with core diameters between 20 nm and 2 μm 30 minutes after their administration, we conclude that 20–200 nm diameter nanoparticles are optimal for passive targeting of the injured left ventricle.

Fluorescent Polystyrene Microbeads as Invisible Security Ink and Optical Vapor Sensor for 4-Nitrotoluene

Color-tunable solid-state emitting polystyrene (PS) microbeads were developed by dispersion polymerization, which showed excellent fluorescent security ink characteristics along with sensitive detection of vapors of nitro aromatics like 4-nitro toluene (4-NT). The fluorophores pyrene and perylenebisimide were incorporated into the PS backbone as acrylate monomer and acrylate cross-linker, respectively. Solid state quantum yields of 94 and 20% were observed for the pyrene and perylenebisimide, respectively, in the PS/Py and PS/PBI polymers. The morphology and solid state fluorescence was measured by SEM, fluorescence microscopy, and absorbance and fluorescence spectroscopy techniques. The ethanol dispersion of the polymer could be used directly as a fluorescent security "invisible" ink, which became visible only under ultraviolet light. The color of the ink could be tuned depending on the amounts of the pyrene and perylenebisimide incorporated with blue and orange-green for pyrene alone or perylenebisimide alone beads respectively and various shades in between including pure white for beads incorporating both the fluorophores. More than 80% quenching of pyrene emission was observed upon exposure of the polymer in the form of powder or as spin-coated films to the vapors of 4-NT while the emission of perylenebisimide was unaffected. The limit of detection was estimated at 10(-5) moles (2.7 ppm) of 4-NT vapors. The ease of synthesis of the material along with its invisible ink characteristics and nitro aromatic vapor detection opens up new opportunities for exploring the application of these PS-based materials as optical sensors and fluorescent ink for security purposes.