Flow Ratio Research Articles

Experiment and Simulation Study on the Cooling Performance of Oil-Cooling PMSM with Hairpin Winding

In this paper, the cooling performance of oil-cooling PMSM with hairpin winding under various oil parameters is analyzed via a simulation and an experiment. The effects of oil jet positions, oil temperatures, and oil flow rates on the cooling performance are analyzed. It is found that increasing the oil temperature in the range of 20 °C to 60 °C, increasing the flow rate of oil jets whose position angle is from 15° to 45°, and increasing the flow rate in the range of 1 L/min to 2 L/min will significantly improve the cooling performance. The apertures of the oil spray ring are optimized using the Taguchi algorithm. The cooling performance is the best when the flow ratio is m(0°):m(15°):m(30°):m(45°):m(60°):m(75°) = 4%:19%:10%:10%:4%:4%. This study provides a guide for the design of the oil-cooling system for the hairpin winding of the PMSM.

Risk Factors of Long-Term Sequelae After Transcatheter Closure of Perimembranous Ventricular Septal Defect in Young Children.

Complications arising from transcatheter closure of perimembranous ventricular septal defects (pmVSD) in children, such as residual shunts and aortic regurgitation (AR), have been observed. However, the associated risk factors remain unclear. This study identified risk factors linked with residual shunts and AR following transcatheter closure of pmVSD in children aged 2-12 years. The medical records of 63 children with pmVSD and a pulmonary-to-systemic blood flow ratio <2.0 who underwent transcatheter closure between 2011 and 2018 were analyzed with a minimum 3-year follow-up. The success rate of transcatheter closure was 98.4%, with no emergency surgery, permanent high-degree atrioventricular block, or mortality. Defects ≥4.5 mm had significantly higher odds of persistent residual shunt (odds ratio [OR] 6.85; P=0.03). The use of an oversize device (≥1.5 mm) showed a trend towards reducing residual shunts (OR 0.23; P=0.06). Age <4 years (OR 27.38; 95% confidence interval [CI] 2.33-321.68) and perimembranous outlet-type VSD (OR 11.94, 95% CI 1.10-129.81) were independent risk factors for AR progression after closure. Careful attention is crucial for pmVSDs ≥4.5 mm to prevent persistent residual shunts in transcatheter closure. Assessing AR risk, particularly in children aged <4 years, is essential while considering the benefits of pmVSD closure.

Steady-state analysis of purge flow passage on the performance of the high-pressure transonic axial turbine at different mass flow ratios

Steady-state analysis of purge flow passage on the performance of the high-pressure transonic axial turbine at different mass flow ratios

Modeling of a Process Window for Tailored Reinforcements in Overmolding Processes

This study explores cost-effective and customized composite applications by strategically placing carbon fiber-reinforced thermoplastics in multi-material designs. The focus is on developing a model for the simultaneous processing of non-reinforced and reinforced thermoplastic layers, with the aim of identifying essential parameters to minimize insert flow and ensure desired fiber orientation and positional integrity. The analysis involves an analytical solution for two layered power-law fluids in a squeeze flow setup, aiming to model the combined flow behavior of Newtonian and pseudo-plastic fluids, highlighting the impact of the non-Newtonian nature. The behavior reveals a non-linear trend in the radial flow ratio towards the logarithmic consistency index ratio compared to a linear trend for Newtonian fluids. While a plateau regime of consistency index ratios presents challenges in flow reduction for both layers, exceeding this ratio, depending on the height ratio of the layers, enables a viable overmolding process. Therefore, attention is required when selectively placing tailored composites with long-fiber-reinforced thermoplastics or unidirectional reinforcements to avoid operating in the plateau region, which can be managed through appropriate cavity or tool designs.

Corporate Governance Moderated Profitability, Liqyidity and Cash Flow on Financial Distress

This study aims to determine the effect of Corporate Governance in moderating Profitability, Liquidity, and Cash Flow on Financial Distress. Net Profit Margin measures profitability. The Current Ratio measures liquidity. The Operating Cash Flow Ratio measures Cash Flow, and Altman Z-score measures Financial Distress. This study uses Corporate Governance as a moderating variable measured by the Board of Commissioners indicator. The sample used in this study is 156 data on manufacturing companies listed on the Indonesia Stock Exchange for 2020-2021. That year, there was an outbreak of the covid-19 pandemic that occurred almost all over the world, allowing many companies to experience financial distress problems. The hypothesis in this study was tested using multiple linear regression. The results showed that profitability had a significant positive effect on financial distress, while liquidity and cash flow had no significant effect on financial distress. Corporate governance as a moderating variable cannot strengthen the influence of Profitability, Liquidity, and Cash Flow on financial distress (Z-Score Index)

Revisitation of reactive direct current magnetron sputtering discharge: Investigation of Mg–CF4, Mg–O2, and Ti–O2 discharges by probe measurements

The reactive direct current (DC) magnetron sputtering discharges of Mg–CF4, Mg–O2, and Ti–O2 were investigated using probe measurements as a function of reactive gas flow ratio. The emission spectroscopy, which was conducted before the probe measurements, demonstrates that all the three DC discharges transit from nonreactive to reactive discharge mode with increasing reactive gas flow ratio. The probe measurements show that the plasma potentials of the Mg–O2 and Ti–O2 DC discharges slightly increase or remain almost constant with increasing reactive gas flow ratio, whereas that of the Mg–CF4 DC discharge drastically decreases at the mode transition. For the same change in reactive gas flow ratio, the discharge voltage of the Mg–CF4 DC discharge slightly increases and that of the Mg–O2 DC discharge drastically increases at the mode transition, whereas that of the Ti–O2 DC discharge slightly decreases at the mode transition. The changes in the cathode sheath potential difference at the mode transition differ between the Mg–CF4 and Ti–O2 DC discharges and the Mg–O2 DC discharge because of the difference in the probability of secondary electron emission at the cathode surface; furthermore, the changes in the anode sheath potential difference at the mode transition differ between the Mg–CF4 DC discharge and the Mg–O2 and Ti–O2 DC discharges because of the difference in the probability of negative-ion formation in the plasma bulk. The most informative results obtained in this study were the differences in the potential differences at the cathode and anode sheaths among the Mg–CF4, Mg–O2, and Ti–O2 DC discharges. They well demonstrated the effects of the change in secondary-emitted species at the cathode surface and the change in reactive gas concentration in the plasma on the potential configuration.

Remimazolam in perioperative management of Eisenmenger syndrome: a case report.

Eisenmenger syndrome (ES) is characterized by severe and irreversible pulmonary hypertension stemming from an uncorrected intracardiac shunt of significant size. The imbalance between systemic and pulmonary artery pressures predisposes patients with ES to the risk of cardiac arrest. Remimazolam has caused less circulatory depression, which may be advantageous for ES. However, no studies reported the use of remimazolam in perioperative ES management. A 45-year-old female patient with ES derived from a ventricular septal defect was scheduled to undergo bilateral adnexectomy for an ovarian tumor. Her oxygen saturation was 80% with 3 L/min oxygen at rest, and her pulmonary and systemic flow ratio was 0.53. She underwent general anesthesia with remimazolam, and intraoperative hemodynamics was stable without hypotension or reduced oxygen saturation. Our successful management of ovarian tumor surgery in a patient with ES using remimazolam reveals its potential effectiveness in perioperative care.

CFD study on the effect of particle properties on the performance of annular jet pump

Abstract The annular jet pump is a type of fluid mechanical pump that operates by exchanging momentum with the fluid. Annular jet pumps possess distinctive advantages in the transportation of solid particles. However, the efficiency of these pumps is significantly impacted by both the physical properties of the particles and their initial concentration, thereby limiting their practical applications. In this paper, by combining other scholars’ designs of annular jet pumps, the effects of different physical densities and different initial concentrations of particles on the flow field, pressure and efficiency of an annular jet pump were analysed based on the RNG k-ε turbulence model and the Mixture multiphase flow model. The efficiency of the annular jet pump decreases with a higher particle bulk density. Specifically, at an initial concentration of 20% and a flow ratio (M) of 0.5, the efficiency of the annular jet pump fluctuates as follows: it changes from 28.736% under single-phase flow conditions to 25.011%, 24.369%, 23.637%, 22.950%, and 21.733% as the density of particulate matter increases. The findings of this study offer valuable theoretical insights for the implementation of annular jet pumps in engineering discharge applications.

The Rossiter equation: Improving the fractional vortex speed and defining an effective length to depth ratio for cavity flows

This paper first reviews well known analytical techniques for predicting the Rossiter modes of a cavity in compressible flow. We combine existing methods to improve the performance in compressible flow. Second, we introduce a method based on an effective length to depth ratio of the cavity from experimental results for predicting frequencies across Mach numbers. Finally, the fractional vortex speed used in the Rossiter equation and its derivatives is calculated from high subsonic (M 0.55) to supersonic (M 2.3) for use in future cavity mode prediction.

Study on the self-adaptive process of droplet traffic to a perturbation of flow resistance at the arms of a micro-T-junction

The response of the water–oil droplet flow to a perturbation of flow resistance added at the arms of a bypassed micro-T-junction is studied through a numerical method. The capillary number of the continuous flow varies between 0.007 and 0.034. Once an additional flow resistance is introduced at the arms of the T-junction, the flow self-adapts to the perturbation and droplets show complex dynamics at the junction, including splitting, merging, and reshaping. During the self-adaptive process, the instantaneous splitting ratios of the dispersed flow show positive correlations with that of the continuous flow. The correlation coefficient reduces as the increase in the amplitude of the perturbation. The ensemble splitting ratios of them, however, are independent. It shows a rather simple law that the ensemble splitting ratios of oil anchor at around a constant value while the corresponding parameter of water varies from 0 to 1. It illustrates that the droplet flow splitting at a T-junction resembles a resilient system, the stiffness of which depends on the capillary number of the flow. The energy loss of the system induced by a perturbation of the flow resistance is self-reduced by just redistributing of droplets into the two arms.

Flow and heat transfer performance of asymmetric fractal tree network in fractal porous media

This study aims to investigate the fluid transport and heat transfer characteristics in fractal porous media, introduce asymmetric factors to derive a generalized optimization principle for asymmetric branching flow and heat transfer, and obtain the optimal radius ratio for the superior flow resistance/heat resistance model; and the accurate models of permeability and thermal conductivity of asymmetric tree-fractal networks are developed and validated against the traditional Murray's law and symmetric tree-fractal network models. The results show that (a) the symmetric case can be regarded as a special case of the asymmetric fractal network model, and Murray's law is correct only for the symmetric bifurcation (flow percentage Ψi = 0.5), and the errors predicted by Murray's law for the asymmetric case with a flow percentage of 10% (Ψi = 0.1, n = 1) are 23.5% and 33.1% with respect to the optimal radius ratio of flow and heat transfer, respectively. (b) The symmetric case has the largest flow resistance and the smallest thermal resistance. The asymmetric length factor and radius ratio have significant effects on the dimensionless flow resistance/thermal resistance of the asymmetric fractal network, and there is a critical radius ratio (βm = 0.84), where a larger asymmetric length factor is detrimental to the flow of the tree-like branching network when β &amp;lt; βm, while the opposite effect is observed when β &amp;gt; βm. (c) The asymmetric radius factor affects the optimal radius ratio for thermal conductivity, but does not change the maximum value of thermal conductivity. (d) The pressure gradient and heat transfer coefficient in the fractal microchannel are related to the variation of the volume flow rate and the increase in the heat flux will weaken heat transfer.

Prognostic Implications of Quantitative Flow Ratio and Plaque Characteristics in Intravascular Ultrasound–Guided Treatment Strategy

BackgroundQuantitative flow ratio (QFR) is a method for evaluating fractional flow reserve without the use of an invasive coronary pressure wire or pharmacological hyperemic agent. ObjectivesThe aim of this study was to investigate the prognostic implications of QFR and plaque characteristics in patients who underwent intravascular ultrasound (IVUS)–guided treatment for intermediate lesions. MethodsAmong the IVUS-guided strategy group in the FLAVOUR (Fractional Flow Reserve and Intravascular Ultrasound for Clinical Outcomes in Patients with Intermediate Stenosis) trial, vessels suitable for QFR analysis were included in this study. High-risk features were defined as low QFR (≤0.90), quantitative high-risk plaque characteristics (qn-HRPCs) (minimal lumen area ≤3.5 mm2, or plaque burden ≥70%), and qualitative high-risk plaque characteristics (ql-HRPCs) (attenuated plaque, positive remodeling, or plaque rupture) assessed using IVUS. The primary clinical endpoint was target vessel failure (TVF), defined as a composite of cardiac death, target vessel myocardial infarction, and target vessel revascularization. ResultsA total of 415 (46.1%) vessels could be analyzable for QFR. The numbers of qn-HRPCs and ql-HRPCs increased with decreasing QFR. Among deferred vessels, those with 3 high-risk features exhibits a significantly higher risk of TVF compared with those with ≤2 high-risk features (12.0% vs 2.7%; HR: 4.54; 95% CI: 1.02-20.29). ConclusionsAmong the IVUS-guided deferred group, vessels with qn-HRPC and ql-HRPC with low QFR (≤0.90) exhibited a significantly higher risk for TVF compared with those with ≤2 features. Integrative assessment of angiography-derived fractional flow reserve and anatomical and morphological plaque characteristics is recommended to improve clinical outcomes in patients undergoing IVUS-guided deferred treatment.

Determinants and Prognoses of Visual-Functional Mismatches After Mechanical Reperfusion in ST-Elevation Myocardial Infarction.

Discordance between the anatomy and physiology of the coronary has important implications for managing patients with stable coronary disease, but its significance in ST-elevation myocardial infarction has not been fully elucidated. The retrospective study involved patients diagnosed with ST-elevation myocardial infarction (STEMI) who underwent percutaneous coronary intervention (PCI), along with quantitative coronary angiography (QCA) and quantitative flow ratio (QFR) assessments. Patients were stratified into four groups regarding the severity of the culprit vessel, both visually and functionally: concordantly negative (QCA-diameter stenosis [DS] ≤ 50% and QFR > 0.80), mismatch (QCA-DS > 50% and QFR > 0.80), reverse mismatch (QCA-DS ≤ 50% and QFR ≤ 0.80), and concordantly positive (QCA-DS > 50% and QFR ≤ 0.80). Multivariable logistic regression analyses were conducted to identify the clinical factors linked to visual-functional mismatches. Kaplan‒Meier analysis was conducted to estimate the 18-month adverse cardiovascular events (MACE)-free survival between the four groups. The study involved 310 patients, with 68 presenting visual-functional mismatch, and 51 exhibiting reverse mismatch. The mismatch was associated with higher angiography-derived microcirculatory resistance (AMR) (adjusted odds ratio [aOR]=1.016, 95% CI: 1.010-1.022, P<0.001). Reverse mismatch was associated with larger area stenosis (aOR=1.044, 95% CI: 1.004-1.086, P=0.032), lower coronary flow velocity (aOR=0.690, 95% CI: 0.567-0.970, P<0.001) and lower AMR (aOR=0.947, 95% CI: 0.924-0.970, P<0.001). Additionally, the mismatch group showed the worst 18-month MACE-free survival among the four groups (Log rank test p = 0.013). AMR plays a significant role in the occurrence of visual-functional mismatches between QCA-DS and QFR, and the mismatch group showed the worst prognosis.

Clinical and imaging predictors for hemorrhagic transformation of acute ischemic stroke after endovascular thrombectomy.

Hemorrhagic transformation (HT) is a common complication of endovascular thrombectomy (EVT) in patients with acute ischemic stroke (AIS). Our study aims to investigate the clinical and imaging predictors of HT and symptomatic intracranial hemorrhage (sICH) in patients who underwent EVT. A retrospective analysis of 118 patients undergoing EVT for acute anterior circulation stroke was performed. Potential clinical and imaging predictors of all patients were collected and multivariate logistic regression was performed. The risk prediction system was constructed according to the multivariate logistic regression results. The incidence of HT and sICH after EVT were 46.6% and 15.3%, respectively. The multivariate logistic regression results showed that Alberta Stroke Program Early CT Score (ASPECTS) (p = .001, odds ratio [OR] = 0.367, 95% [confidence interval] CI, 0.201-0.670), collateral status (p<.001, OR = 0.117, 95% CI, 0.042-0.325), relative cerebral blood flow (CBF) ratio (p = .025, OR = 0.943, 95% CI, 0.895-0.993), and blood glucose on admission (p = .012, OR = 1.258, 95% CI, 1.053-1.504) were associated with HT. While for sICH, collateral circulation (p = .007, OR = 0.148, 95% CI, 0.037-0.589), ASPECTS (p = .033, OR = 0.510, 95% CI, 0.274-0.946), and blood glucose (p = .005, OR = 1.304, 95% CI, 1.082-1.573) were independent factors. The predictive model for HT after EVT was established, and the sensitivity and specificity of it were 90.9% and 79.4%, respectively, with the area under the curve of 90.0% (84.5%-95.4%). Collateral status, ASPECTS, relative CBF ratio, and blood glucose on admission were predictors for HT in AIS patients, while collateral status, ASPECTS, and blood glucose on admission were also predictors for sICH. In addition, the established predictive model showed good diagnostic value for prediction of HT after EVT.

Risk factors for instent restenosis of sirolimus-coated stents in coronary intervention for patients with unstable angina

To investigate the instent restenosis rate of sirolimus-coated stents in percutaneous coronary intervention (PCI) and risk factors for in-stent restenosis, patients with unstable angina (UA) caused by coronary artery stenosis were enrolled, and all clinical and imaging data were analyzed. Among 143 enrolled patients with UA aged 35–83 (mean 60.9 ± 10.0) years enrolled, there were 114 (79.7%) male and 29 (20.3%) female patients. Arterial stenosis was present in one coronary artery in 6 (4.2%) patients, in two coronary arteries in 20 (14.0%) patients, in three arteries in 116 (81.1%), and in four coronary arteries in 1 (0.7%) patient. Stenting was successfully performed in all (100%) patients, and 181 stents were deployed. The quantitative flow ratio (QFR) was 0.92 ± 0.03 (range 0.84–0.96) immediately after stenting, and the TIMI was grade 3 in all patients. The diameter of the stents deployed ranged 2.25–4 mm (mean 3.04 ± 0.44) with a length ranging 10 mm to 104 mm (mean 32.73 ± 15.5). Follow-up angiography was performed in all patients with a duration of 1–92 (mean 15.0 ± 18.8) months. Instent restenosis ≥ 50% occurred in 25 (17.5%) patients. In univariate logistic regression analysis, significant (P < 0.05) risk factors for instent restenosis ≥ 50% were QFR (OR 0.036, 95% CI 0.13–0.97), stent diameter (OR 0.43, 95% CI 0.18–0.92), hypertension (OR 3.16, 95% CI 1.02–9.82), smoking (OR 0.31, 95% CI 0.11–0.89), and neutrophil count (OR 2.22, 95% CI 1.10–5.44). In multivariate analysis, QFR (OR 0.02, 95% CI 0.002–0.19), stent diameter (OR 0.06, 95% CI 0.005–0.59), hypertension (OR 6.75, 95% CI 1.83–35.72) and neutrophil count (OR 276.07, 95% CI 12.32–10,959.95) were significant (P < 0.05) independent risk factors for instent restenosis ≥ 50%. In conclusion, certain instent restenosis rates occurs after the sirolimus-eluted coronary stent deployment for the treatment of coronary artery stenosis in patients with UA, and quantitative flow ratio after stenting, stent diameter, hypertension, and neutrophil count are significant risk factors for instent restenosis of the sirolimus-coated stents in coronary intervention.

Standardized angiographic projections allow evaluation of coronary artery side branches with quantitative flow ratio (QFR)

Quantitative flow ratio (QFR) is a novel, software-based noninvasive method for the quantitative evaluation of coronary physiology. QFR results correlate with invasive FFR measurements in the three main epicardial coronary arteries. However, QFR data for the evaluation of coronary side branches (SB) are scarce. The evaluation of QFR-performance of SB was retrospective and prospective. Eighty-seven patients with suspected chronic coronary syndrome, who received angiography using routine core lab projections, were retrospectively analyzed. On the second part 37 patients, who received angiography using recommended standardized coronary angiography projections, were prospectively analyzed. Quantitative analysis was performed for SB with a maximum lumen diameter proximal of ≥2 mm based on quantitative coronary angiography (QCA) by two certified experts with the software QAngio XA 3D 3.2. Using routine projections, QFR computation in 55 % of the SB were obtained (123 out of 224). Using standardized projections, 85 % of SB were computed by QFR (64 out of 75; p < 0.001 vs routine projections). The fluoroscopy time for recommended projections was not significantly different as opposed to routine projections (3.75 ± 2.2 vs. 4.58 ± 3.00 min, p = 2.6986). Using the standardized projections was associated with a higher amount of contrast medium (53.44 ± 24.23 vs. 87.95 ± 43.73 ml, p < 0.01), longer overall procedure time (23.23 ± 16.35 vs. 36.14 ± 17.21 min, p < 0.01) and a higher dose area product (1152.28 ± 576.70 vs. 2540.68 ± 1774.07 cGycm2, p < 0.01). Our study shows that the blood flow of the vast majority of coronary SB can be determined non-invasively by QFR in addition to the main epicardial coronary arteries when standardized projections are used.

Evaluating physical controls on conduit flow contribution to spring discharge

The physical controls on the contribution of conduit to spring discharge, quantified as the ratio of conduit flow to spring discharge (Qc/Q), are evaluated through numerical simulations using MODFLOW-Conduit Flow Process. The controlling factors include the ratio of conduit surface roughness to conduit diameter (ε/D), the hydraulic conductivity ratio between the conduit wall and the porous matrix (Kc/K), the ratio of groundwater recharge to the hydraulic conductivity of the porous matrix, and conduit density (Cd) defined as the ratio of total conduit length to springshed area. For a single conduit, Qc/Q increases with Kc/K when flow in the conduit is laminar. When flow is turbulent, Qc/Q is stable and then decreases with ε/D, increases with Kc/K, and decreases with R/K due to the limited exchange capacity between matrix and conduit (i.e., small Kc/K). The results of hypothetical conduit networks show that Qc/Q increases with Cd but is not sensitive to the two sets of network structure evaluated. The sensitivity analysis for the Silver Springs in Florida shows that the spatial heterogeneity of conduit diameter causes higher Qc/Q, and Qc/Q is most sensitive to the conduit density, followed by R/K, and then Kc/K.

Capital Structure Function of Cash Flow Based Corporate Finance (CFCF) Model

Purpose: The purpose of this article is to explain the capital structure function of CFCF model explaining by Yilmaz (2022) and Yilmaz (2023).&#x0D; Materials and Methods: First, the 11 cash flow ratios were selected from CFCF model (Yilmaz, 2023). (Look at Yilmaz 2003 for all 30 ratios and their groups). Then, these ratios were explained from the point of view of capital structure function of the FCFC model. Then, they were applied on the Apple Corp. financial statements. Their calculations and comments were fulfilled by the writer.&#x0D; Findings: This is a theoretical model. As a finding, the 11 ratios could be calculated by the writer. Accordingly, the cash flow ratios of the Apple Corp. shows that its capital structure is managed well and the company does not have any cash flow based capital structure management issue. &#x0D; Implications to Theory, Practice and Policy: All companies could use this tool, capital structure function of cash flow based corporate finance (CFCF) model to learn capital structure issues and to solve them.

Geographic disparity of pathophysiological coronary artery disease characteristics: Insights from ASET trials

BackgroundThe geographical disparity in the pathophysiological pattern of coronary artery disease (CAD) among patients undergoing percutaneous coronary intervention (PCI) is unknown. ObjectivesTo elucidate the geographical variance in the pathophysiological characteristics of CAD. MethodsPhysiological indices derived from angiography-based fractional flow reserve pullbacks from patients with chronic coronary syndrome enrolled in the ASET Japan (n = 206) and ASET Brazil (n = 201) studies, which shared the same eligibility criteria, were analysed.The pathophysiological patterns of CAD were characterised using Murray law-based quantitative flow ratio (μQFR)-derived indices acquired from pre-PCI angiograms. The diffuseness of CAD was defined by the μQFR pullback pressure gradient index. ResultsSignificant functional stenoses pre-PCI (μQFR ≤0.80) were more frequent in ASET Japan compared to ASET Brazil (89.9% vs. 67.5%, p < 0.001), as were rates of a post-PCI μQFR <0.91 (22.1% vs. 12.9%, p = 0.013). In the multivariable analysis, pre-procedural μQFR and diffuse disease were independent factors for predicting a post-PCI μQFR <0.91, which contributed to the different rates of post-PCI μQFR ≥0.91 between the studies. Among vessels with a post-PCI μQFR <0.91, a consistent diffuse pattern of CAD pre- and post-PCI occurred in 78.3% and 76.7% of patients in ASET Japan and Brazil, respectively; only 6.3% (Japan) and 10.0% (Brazil) of vessels had a major residual gradient. Independent risk factors for diffuse disease were diabetes mellitus in ASET Japan, and age and male gender in Brazil. ConclusionsThere was geographic disparity in pre-procedural angiography-based pathophysiological characteristics. The combined pre-procedural physiological assessment of vessel μQFR and diffuseness of CAD may potentially identify patients who will benefit most from PCI.

Analysis of Investors’ Choices in Technology Companies

This paper examines how to analyze which technology companies are suitable for different types of investors through various financial indicators. First, this paper chooses four technology companies, namely Tesla, Tencent, Microsoft and Apple. Next, Yahoo searches for various profit and loss metrics for several companies and groups these metrics into three categories, including risk, profitability and market ratio. Finally, reasonable suggestions are given by analyzing the investment preferences of nine kinds of investors. The nine types of Investors are price/earnings to growth ratio investors (PEG investors), discounted cash flow Investors (DCF investors), income investors, value investors, index investors, momentum investors, insider investors, ratio analysis and stock buyer. According to the analysis results, PEG investors and DCF investors may choose Tesla, while DCF investors and income investors may choose Tencent. In addition to index investors, other investors are likely to choose Microsoft. Apple is likely to be picked by PEG investors, value investors and momentum investors. The research significance of this paper is to help investors who lack certain financial knowledge to choose their own types of stocks, and to describe the characteristics of different types of investors to help investors judge which investment method is suitable for them.