Capillary Tube Research Articles

Influence of the surface energy of a basalt fiber on capillary wicking and in-plane permeability of reinforcements

This study evaluates the influence of a thermal treatment of a basalt fiber on capillary wicking tests and in-plane permeability experiments, under several pressure differences. The impact of the treatment was characterized at three scales: microscopic, to determine the fiber surface energy; mesoscopic, to estimate an equivalent capillary pressure (Pcap) of the fabric in spontaneous impregnation; and macroscopic, to determine the saturated (Ksat) and unsaturated (Kunsat) permeability of the fibrous preform at the process scale. Results at the microscopic scale showed that the thermal treatment increased the polarity of the fiber by 22% and decreased its surface roughness. Capillary wicking tests showed that the treated fabric presents a better affinity with water, increasing Pcap by 68%. At the process scale, permeability experiments showed the increase of Ksat and Kunsat after treatment. Finally, results of capillary pressure (ΔPγ) showed a dominance of capillary effects under the negative pressure difference.

Role of motility and nutrient availability in drying patterns of algal droplets.

Sessile drying droplets in various bio-related systems attracted attention due to the complex interactions between convective flows, droplet pinning, mechanical stress, wettability, and the emergence of unique patterns. This study focuses on the drying dynamics of Chlamydomonas reinhardtii (chlamys), a versatile model algae used in molecular biology and biotechnology. The experimental findings shed light on how motility and nutrient availability influence morphological patterns- a fusion of macroscopic fluid dynamics and microbiology. This paper further discusses the interplay of two competing stressors during drying- nutrient scarcity (quantitative analysis) and mechanical stress (qualitative analysis), where the global mechanical stress does not induce cracks. Interestingly, motile chlamys form clusters under nutrient scarcity due to metabolic stress, indicating the onset of flocculation, a common feature observed in microbial systems. Moreover, non-motile chlamys exhibit an "anomalous coffee-ring effect" in the presence of nutrients, with an inward movement observed near the droplet edge despite sufficient water in the droplet. The quantitative image processing techniques provide fundamental insights into these behaviors in classifying the patterns into four categories (motile+with nutrients, motile+without nutrients, non-motile+with nutrients, and non-motile+without nutrients) across five distinct drying stages- Droplet Deposition, Capillary Flow, Dynamic Droplet Phase, Aggregation Phase, and Dried Morphology.

Nanoscopic Insights into the Collapse of Metal-Organic Frameworks during Solvent Evacuation: Molecular Simulation Investigation.

Many metal-organic frameworks (MOFs) undergo structural collapse upon solvent evacuation during activation, which is attributed to the capillary force generated by the solvent. However, little effort has been devoted to unveiling the nature of such a force. Herein, we employ molecular dynamics (MD) simulations to investigate the evacuation of different solvents in two MOFs (MOF-5 and UMCM-9). The contractive stress induced by solvent evacuation is quantified and unraveled to positively correlate with the surface tension of the solvent. Moreover, the mechanical strength (or amorphization) of the MOF is calculated using reactive MD simulations. By comparing the contractive stress with the amorphization stress, for the first time, we predict the likelihood of collapse of MOFs during activation by different solvents, which agrees well with the experiments. The methodology developed provides nanoscopic insights into the activation process; it can assist in avoiding structural collapse by judiciously selecting a proper solvent for activation or by modifying a framework.

Multilayer patch functionalized microfibrillated cellulosic paper sensor for sweat glucose monitoring.

Electrochemical analysis of glucose monitoring without painful blood collection provides a new noninvasive route for monitoring glucose levels. Thus, in this study, biobased cellulosic papers (methylated and phosphorylated one) based glucose monitoring sensor is developed. To achieve high hydrophilicity, microfibrillated cellulose (MFC) were functionalized using hexokinase mediated phosphorylation (-OH to -[Formula: see text]). The instinctive increased surface charge density from 36.2 ± 3.4 to 118.4 ± 1.2 µmol/g and decrease contact angle (45°-22°) confirms the increased hydrophilicity of paper. Furthermore, functionalized phos-MFC paper increase the capillary flow of sweat, required low quantity (1µl) of sweat for accurate analysis of glucose level. Additionally, chemically induced methyl groups (-CH3) make the sensor more barrier to other chemicals. In addition, a multilayer patch design combined with sensor miniaturization was used to lead to an increase in the efficiency of the sweat collection and sensing processes. Besides, this paper sensor integrated with artificial transdermal drug delivery unit (agarose gel as skin) for monitoring glucose levels in sweat. The patch monitoring system increase the accuracy of sensing with fluctuation in sweat vol. (1-4µl), temperature (20-70 °C), and pH (4.0-7.0). In addition, temperature dependency artificial transdermal delivery (within agarose gel) of drug metformin agrees the measurement accuracy of sensor, called "switch system" without any error. As a result, the reported MFC paper based multi-patch disposable sensing system provides a novel closed-loop solution for the noninvasive sweat-based management of diabetes mellitus.

Molecular Dynamics Simulations of Lubricant Supply in Porous Polyimide Bearing Retainers

Space bearing retainers are widely made of a porous, oil-impregnated material due to the unmaintainability of spacecraft. Porous polyimide (PI) material with a certain micropore structure can be used as a lubricant storage and migration channel to realize the lubricant circulation supply in the bearing system. In this work, molecular dynamics simulations are adopted to model the lubricant outflow process from the pore of the PI material. Coarse-grained models are constructed to investigate the lubricant migration behaviors with different rotation speeds, rotation radii, and pore sizes. The results show that a lubricant within the pore fails to outflow due to the capillary effect in a static state. However, for the rotating pores, if the centrifugal forces resulting from rotation exceed the capillary forces, the lubricants will begin to flow out. Furthermore, the lubricant in the large pore is easier to outflow due to the smaller capillary force, which is the main mechanism of lubricant outflow from the pores.

Investigating of vibration and noise characteristics in two-phase gas-liquid flow through a spiral capillary tube

The vaporization of refrigerant in the liquid-phase in spiral capillary tube induces complex two-phase flow that causes vibrations and noise, which affect the performance and stability of refrigeration systems. Therefore, the flow patterns, vibrations, flow-borne and structure-borne noises in spiral capillary tube are explored, and the effects of coil diameters, pitches and temperatures are analyzed. The results showed that the flow upstream the vaporization point was dominant by liquid-phase, then changed to bubbly flow downstream the vaporization point under various structures, and further changed to mist flow near the outlet, while it changed to gas-phase flow near the outlet under high temperature. The flow-borne noise was mainly affected by the flow turbulence, and the total sound pressure level (TSPL) increased by 17.1 % on average as the temperature increased from 309.6 to 317.6 K, and rose with the increase in pitch. As the coil diameter increased, the TSPL first increased and then decreased. Moreover, the maximum deformation of structure increased by 58.33 % as the diameter increased from 35 to 50 mm, but changed little with various pitches. The changing trends of vibration intensity caused the similar variations of structure-borne noise. The TSPL of structure-borne noise increased by 9.14 % with the diameter increasing from 35 to 50 mm, but it changed little at various pitches. The TSPL of structure-borne noise was much higher than flow-borne noise, which meant that improving the structural vibration can control the noise of refrigerant flow in spiral capillary tube.

The start-up characteristics of a novel loop heat pipe with stainless steel capillary wick

Loop heat pipe (LHP) is an advanced thermal management technology that utilizes liquid–vapor phase change and capillary action to achieve efficient heat transfer across long distances and in various directions. The start-up of an LHP is crucial for its reliable and stable operation. This study aims to explore the start-up characteristics and temperature variations of various components under different heating conditions by designing a cost-effective flat plate evaporator LHP with a stainless-steel casing and acetone as the working fluid. The experimental analysis examined the performance of the LHP under varying heating powers from 28 to 60 W, positions, and gravity angles. The findings revealed that the LHP successfully started at 28 W, and a temperature overshoot occured when the heating position was near the compensation chamber. Notably, the start-up time was 400 s faster compared to the heating condition near the mean pressure chamber. When the evaporator was tilted such that the compensation chamber was above the evaporator’s pressure equalization chamber, circulation within the LHP could not be established. The thermal resistance of the LHP decreased with increasing heating power, achieving a maximum reduction of 51.51 %. When both the compensation chamber and the mean pressure chamber were heated simultaneously, the impact of the gravity inclination angle on thermal resistance was minimized. This study introduces an innovative capillary wick LHP with high start-up success rates and cost-effectiveness, providing both empirical data and theoretical insights for the refinement and optimization of civilian LHP designs.

Simulation of a capillary tube, fibre dual-readout calorimeter in DD4hep

Over the past years the dual-readout method for calorimetry, which exploits complementary information from Scintillation and Cherenkov channels, has emerged as candidate to fulfil the requirements for precision physics at future circular lepton colliders. While the dual-readout approach has been tested experimentally quite extensively, this type of calorimeter has never been used in an experiment at a collider. In recent years dedicated studies in simulation have investigated various detector geometries based on a fibre dual-readout calorimeter. One variation of the geometry, relying on capillary tubes, promises easy assembly with excellent geometrical accuracy at a moderate cost. In these proceedings, we present the status and latest results from a full 4π detector geometry simulation in DD4hep. The simulation is used to estimate the performance of a dual-readout calorimeter for single electromagnetic and hadronic particles. The results for the dual-readout technique show an improvement in energy resolution for both electromagnetic and hadronic showers, with respect to single channel measurements.

Review on spontaneous imbibition mechanisms in gas-water systems: Impacts on unconventional gas production and CO2 geo-sequestration

Spontaneous imbibition, a fundamental process in porous media, involves the displacement of a non-wetting phase by a wetting phase driven by capillary pressure. It plays a key role in various applications, particularly in unconventional gas production and greenhouse gas geo-sequestration. Despite extensive research in this area, conflicting results and explanations persist regarding imbibition phenomena, particularly in gas-water systems. This paper aims to address this gap by providing a comprehensive review of basic concepts, mechanical analyses, pore-filling patterns, front evolutions, and influencing factors associated with spontaneous imbibition. Mechanical factors including capillary force, viscous force, gravitational force, hydrostatic force, inertial force, capillary back force, and dead end force, play crucial roles in water imbibition with different boundary types. The pore-filling pattern significantly affects microscopic fluid distribution and front evolution during the imbibition process. To resolve conflicting findings, we systematically analyze the influencing factors of spontaneous imbibition within gas-water systems, encompassing rock properties, fluid characteristics, rock-fluid interactions, and reservoir properties. Furthermore, we present an in-depth discussion on the imbibition and trapping mechanisms relevant to unconventional gas production and CO2 geo-sequestration, providing insights into force analyses and influencing factors. Gas production strategies and favorable conditions for CO2 capillary trapping are proposed. Finally, we outline existing knowledge gaps and suggest potential directions for future research. This review thus provides useful insights and suggestions for advancing our understanding of spontaneous imbibition within gas-water systems and optimizing unconventional gas production and CO2 geo-sequestration practices.

A-342 Precision Evaluation of the pH, PO2 and PCO2 tests in the i-STAT® G3+ Cartridge using the i-STAT 1 System for Venous, Arterial and Capillary Whole Blood Specimens in Clinical Settings

Abstract Background Precise and accurate measurements of blood gases are important for the diagnosis, monitoring and treatment of respiratory, metabolic, and acid-base disturbances. This study demonstrates the precision of the pH, partial pressure of oxygen (PO2), and partial pressure of carbon dioxide (PCO2) tests in the i-STAT G3+ cartridge with the i-STAT 1 System in arterial, venous, and capillary whole blood specimens in point-of-care or clinical laboratory settings. Methods The precision of the i-STAT pH, PO2, and PCO2 tests in the i-STAT G3+ cartridge was assessed at external clinical sites by end-users using whole blood specimens across the measurement range for each test: pH (6.500 - 7.800 pH units), PO2 (5 - 700 mmHg), PCO2 (5.0 - 130.0 mmHg). The study included venous whole blood samples from ∼140 adult subjects (≥ 18 years) and arterial whole blood samples from ∼140 adult subjects at 3 clinical sites. Each whole blood sample was run in duplicate on the i-STAT G3+ cartridge. In addition, ∼140 specimens were collected in capillary tubes using two fingerstick draws from adult subjects and ∼20 capillary heel-stick specimens were collected into two capillary tubes from neonate subjects (birth - 28 days) at two clinical sites. Specimens used in this study were prospectively collected venous, arterial, or capillary specimens under an Institutional Review Board approved informed consent or were de-identified leftover venous or arterial specimens. For each specimen type, duplicates from each subject were grouped into subintervals based on their mean values. The subintervals included the medical decision levels of 7.300, 7.350 and 7.450 pH units for pH, 30, 45 and 60 mmHg for PO2 and 35, 45, 50 and 70 mmHg for PCO2. The estimates of the pooled standard deviation (SD) and pooled coefficient of variation (%CV), as well as their respective 95% confidence intervals were calculated for each subinterval. Results Across all specimen types (excluding outliers), the pooled SD for pH ranged from 0.00591 - 0.01747 pH units for subintervals 6.500 - 7.300, >7.300 - 7.450, >7.450 - 7.800 pH units. For PO2, the pooled SD ranged from 0.71 - 3.76 mmHg for subintervals 10 - 40 mmHg and >40 - 50 mmHg and the pooled %CV ranged from 1.63 - 8.76 %CV for subintervals >50 - 100 mmHg, >100 - 250 mmHg and >250 - 700 mmHg. For PCO2, the pooled SD ranged from 0.000 - 1.709 mmHg for subintervals 5.0 - 35.0 mmHg, >35.0 - 50.0 mmHg and >50.0 - 62.5 mmHg and the pooled %CV ranged from 1.10 - 3.62 %CV for subinterval >62.5 - 130.0 mmHg. Conclusions The precision study demonstrated that the pH, PO2 and PCO2 tests in the i-STAT G3+ cartridge when tested using the i-STAT 1 System deliver precise results within ∼2 minutes for venous, arterial, and capillary whole blood patient specimens when tested by end users in a point-of-care or clinical laboratory setting. These studies were funded by Abbott Laboratories.

A-341 Precision Evaluation of the i-STAT® Glucose Test in the i-STAT G Cartridge using thei-STAT 1 System for Venous, Arterial and Capillary Whole Blood Specimens in Clinical Settings

Abstract Background Precise and accurate measurements of whole blood glucose levels are important for the diagnosis and treatment of patients suffering from diabetes and hypoglycemia. This study demonstrates the precision of the i-STAT G cartridge with the i-STAT 1 System in arterial, venous, or capillary whole blood in point of care or clinical laboratory settings. Methods The precision of the i-STAT G cartridge was assessed at external clinical sites by intended end users with whole blood specimens across the measurement range of 20 - 700 mg/dL. The study included testing venous whole blood samples from 154 adult (≥ 18 years) patients and arterial whole blood samples from 173 adult patients at three clinical sites. Each whole blood sample was run in duplicate on the i-STAT G cartridge. In addition, 139 capillary whole blood specimens from both adult subjects and neonate subjects (birth - 28 days) were collected and tested for capillary whole blood precision. Duplicate fingerstick draws were collected in capillary tubes from 119 adult subjects at two clinical sites and duplicate heel-stick specimens were collected in capillary tubes from 20 neonate subjects at two clinical sites. Specimens used in this study were prospectively collected venous, arterial, or capillary specimens under an Institutional Review Board approved informed consent or were de-identified leftover venous or arterial specimens. For each specimen type, duplicates from each subject were grouped into subintervals based on their mean values. The subintervals included the glucose medical decision levels of 45 mg/dL, 120 mg/dL and 180 mg/dL. The estimates of the pooled standard deviation (SD) and pooled coefficient of variation (%CV), as well as their respective 95% confidence intervals (CI) were calculated for each subinterval (20-90 mg/dL, >90-150 mg/dL, >150-250 mg/dL, >250-700 mg/dL or >250-400 mg/dL and >400-700 mg/dL, as applicable). The precision estimates for each subinterval were compared against an acceptance criteria of the greater of 3 mg/dL or 5% of the mean (mg/dL) of the subinterval. Results The whole blood precision was found to be less than or equal to 5.00 %CV for all subintervals for each specimen type. For venous specimens, the %CV ranged from 0.35% to 0.43%; for arterial specimens the %CV ranged from 0.26% to 0.46% and for capillary specimens (adult and neonate combined), the %CV ranged from 1.38% to 2.71%. Conclusions The study demonstrated that the i-STAT Glucose test in the i-STAT G cartridge when tested using the i-STAT 1 System delivers precise results within ∼2 minutes for venous, arterial, and capillary whole blood patient specimens across a glucose range of 20 - 700 mg/dL when tested by end users in a point of care or clinical laboratory setting. The studies were funded by Abbott Laboratories.

A-328 Accuracy of the Glucose Test in the i-STAT® G Cartridge Using the i-STAT 1 System for Venous, Arterial and Capillary Whole Blood Specimens in Clinical Settings

Abstract Background Precise and accurate measurements of whole blood glucose levels are important for the diagnosis, monitoring and treatment of carbohydrate metabolism disorders, such as diabetes and hypoglycemia. This study demonstrates the accuracy of the glucose test in the i-STAT G cartridge with the i-STAT 1 System in arterial, venous, and capillary whole blood specimens in point of care or clinical laboratory settings. Methods The accuracy of the glucose test in the i-STAT G cartridge was assessed at external clinical sites in a method comparison study using whole blood specimens across the measurement range of 20 - 700 mg/dL. Specimens used in this study were venous, arterial, and capillary specimens prospectively collected under Institutional Review Board-approved informed consent or were leftover de-identified venous or arterial specimens. The study included venous whole blood samples from 164 adult subjects (≥ 18 years) and arterial whole blood samples from 173 adult subjects at 3 clinical sites, and capillary whole blood samples from 211 adult subject at 3 clinicals sites and 23 neonate subjects (birth to 28 days) at 2 clinical sites. For venous and arterial whole blood, samples were collected and tested in duplicate on the i-STAT G cartridge and on the i-STAT CHEM8+ cartridge (comparator). For capillary whole blood samples, adult fingerstick samples and neonate heel-stick samples were collected in capillary tubes and tested in singlicate on the i-STAT G cartridge and in singlicate on the epoc® Blood Analysis System (comparator). Passing-Bablok linear regression was performed for venous and arterial whole blood samples using the first replicate from the i-STAT G cartridge versus the mean result of the comparator, and for capillary whole blood samples (adult and neonate combined) using the singlicate result from the i-STAT G cartridge versus the singlicate result of the comparator. Results Passing-Bablok regression of i-STAT G cartridge results versus the comparator was used to calculate slope and correlation coefficient (r). Adult venous whole blood results had slope = 1.00 and r = 1.00, and adult arterial whole blood results had slope = 1.00 and r = 1.00. Adult and neonate capillary whole blood results had slope = 1.00 and r = 1.00. Conclusions These results demonstrate that the i-STAT 1 System delivers accurate glucose test results within ∼2 minutes using the i-STAT G cartridge for venous, arterial and capillary whole blood samples for adult and neonate subjects across a glucose range of 20-700 mg/dL when tested by end-users in a point of care or clinical laboratory setting. This study was funded by Abbott Laboratories.

A-329 Accuracy of the pH, PO2, and PCO2 Tests in the i-STAT® G3+ Cartridge Using the i-STAT 1 System for Venous, Arterial and Capillary Whole Blood Specimens in Clinical Settings

Abstract Background Precise and accurate measurements of blood gases are important for the diagnosis, monitoring and treatment of respiratory, metabolic, and acid-base disturbances. This study demonstrates the accuracy of the pH, partial pressure of oxygen (PO2), and partial pressure of carbon dioxide (PCO2) tests in the i-STAT G3+ cartridge with the i-STAT 1 System in arterial, venous, and capillary whole blood specimens in point of care or clinical laboratory settings. Methods The accuracy of the PO2, and PCO2 tests in the i-STAT G3+ cartridge was assessed at external clinical sites in a method comparison study using whole blood specimens across the measurement range for each test: pH 6.5-7.8, PO2 5-700 mmHg, PCO2 5.0-130.0 mmHg. Specimens used in this study were venous, arterial, and capillary specimens prospectively collected under Institutional Review Board-approved informed consent or were leftover de-identified venous or arterial specimens. The study included venous and arterial whole blood samples from ∼140 adult subjects (≥ 18 years) at 3 clinical sites, and capillary whole blood samples from ∼180 adult subject at 3 clinicals sites and ∼25 neonate subjects (birth to 28 days) at 2 clinical sites. The RapidPoint System was used as comparator. For venous and arterial whole blood, samples were collected and tested in duplicate on the i-STAT G3+ cartridge and in singlicate on the RapidPoint System. For capillary whole blood samples, adult fingerstick samples and neonate heel-stick samples were collected in capillary tubes and tested in singlicate on the i-STAT G3+ cartridge and on the RapidPoint System. Passing-Bablok regression was performed for venous and arterial whole blood samples combined, using the first replicate from the i-STAT G3+ cartridge versus the singlicate result from the comparator, and for capillary whole blood samples (adult and neonate combined) using the singlicate result from the i-STAT G3+ cartridge versus the singlicate result from the comparator. Results Passing-Bablok regression of i-STAT G3+ cartridge results versus the comparator was used to calculate slope and correlation coefficient (r). For adult venous and arterial whole blood results, pH had slope = 0.96 and r = 0.99, PO2 had slope = 1.05 and r = 1.00, and PCO2 had slope = 1.04 and r = 0.98. For adult and neonate capillary whole blood results, pH had slope = 1.02 and r = 0.98, PO2 had slope = 1.09 and r = 0.99, and PCO2 had slope = 1.07 and r = 0.96. Conclusions These results demonstrate that the i-STAT 1 System delivers accurate pH, PO2, and PCO2 test results with ∼2 minutes using the i-STAT G3+ cartridge for venous, arterial and capillary whole blood samples for adult and neonate subjects when tested by end-users in a point of care or clinical laboratory setting. This study was funded by Abbott Laboratories.

Enhancing tapping mode atomic force microscopy using AutoResonance control and a hybrid dynamic model

We present a novel method for analyzing tapping mode atomic force microscopy (AFM), enhancing topography reconstruction’s accuracy and speed. Our approach integrates an automatic resonance-tracking control scheme with a hybrid dynamic model that considers interactions between the AFM tip and the sample, and the oscillating sensor dynamics. A key aspect of our method is a simplified model that captures intricate dynamic behavior as a function of the distance from the topography. This model enables the immediate approximation of the distance from the topography, eliminating the necessity to lock onto the nominal distance as done with classical AFMs. To validate the accuracy, we conducted numerical simulations of Van der Waals and capillary interaction forces, as well as experimental measurements of a coin’s topography. The results affirm the effectiveness of our approach in enhancing AFM imaging and characterization capabilities.

Fluorescence visualization dynamics of carbonated water injection processes in homogeneous glass micromodels

Understanding the flow behavior of oil–water phases in porous media is crucial for revealing the kinetic mechanisms underlying oil–water movement. In this study, we designed and constructed a fluorescence visualization experimental platform for carbonated water injection (CWI). We evaluated the effects of nine distinct injection rates on oil production and CO2 sequestration capabilities using three types of homogeneous porous structure micromodels. The microscale oil–water seepage behavior at the pore scale was also explored. The experimental results indicate that optimally increasing the injection rate can improve displacement efficiency, whereas excessively high rates may lead to viscous and capillary fingering. The geometry of the micromodels, particularly the hexagonal matrix, demonstrates potential advantages in enhancing oil displacement due to its uniform flow paths. The capillary number (Ca) significantly influences oil droplet capture behavior within micromodels. For instance, micromodel A captures the largest ganglion area at low Ca values, with a noticeable reduction in average ganglion area as Ca increases. Conversely, micromodels B and C exhibit similar trends in ganglion size variation at high Ca values, suggesting a more uniform impact of pore structure on oil droplet capture behavior. At elevated Ca values, capillary forces exert a more uniform and controlled effect on oil droplet capture and release, minimizing size variability. Additionally, the injection rate plays a critical role in CO2 sequestration, with higher rates promoting convective mixing between CO2 and reservoir fluids, thereby enhancing dissolution and storage efficiency. The complexity of the pore structure, characterized by the presence of micropores and macropores, affects the dissolution kinetics and mobility of CO2, influencing sequestration efficiency. These experimental findings provide valuable insights into the dynamics of oil–water motion and the potential for enhanced oil recovery (EOR) and CO2 storage, offering essential guidance for optimizing CWI strategies in the petroleum industry.

B-169 Combining the EXENT System and LC-MS for the Detection of Monoclonal Immunoglobulins at Low Levels

Abstract Background The EXENT® system is an automated platform designed to quantify monoclonal immunoglobulins in serum. EXENT® combines immunoprecipitation and MALDI-TOF mass spectrometry for the detection of monoclonal immunoglobulins at levels lower than traditional gel based methods. This study was designed to demonstrate if EXENT® prepared samples that were negative could be reflexed to a more sensitive method based on capillary flow Liquid Chromatography- Mass Spectrometry (LC-MS) without any modifications to the EXENT® prepared sample. Methods Patient samples containing a monoclonal immunoglobulin (ranging from 20 to 40 g/L) were diluted into pooled polyclonal serum and the samples were prepared and analyzed by EXENT®. Samples that were negative by EXENT® were reflexed by directly loading EXENT® eluates onto the LC-MS instrument. The abundance of the monoclonal immunoglobulin was defined by the signal-to-noise (S/N) of the light chain peak observed after deconvolution. Results Baseline samples were diluted down to two levels, 0.100 g/L and 0.001 g/L. LC-MS detected the same light chain from the monoclonal immunoglobulin as the EXENT® system in all reflexed samples that were negative by EXENT®. Conclusions LC-MS can detect monoclonal immunoglobulins that can no longer be detected using the EXENT® system by tracking the unique molecular mass of the monoclonal light chain. Reflexing samples to LC-MS did not require additional sample handling resulting in a faster time-to-result than current NGS, NGF, and clonotypic peptide approaches. Furthermore, monitoring the intact monoclonal light chain circumvents enzymatic cleavage to create a unique clonotypic peptide, alleviating a situation where no unique peptide can be generated as has been shown previously by Bergen et al. As a consequence, this reflex-methodology results in a consistent way of measuring the presence of malignant B-cells with high sensitivity.

Dynamic wetting mechanism of coal under different CO2 pressure: A new analytical basis through T2 cutoff

The technology of injecting carbon dioxide into coal seams to reduce greenhouse gas emissions and has brought attraction on the wettability of coal. As a fast and non-destructive method, nuclear magnetic resonance (NMR) is widely used in the evaluation of coal wettability, but the inconsistency of analytical basis makes the quantitative evaluation of coal wettability changes uncertain. In this study, based on NMR combined with centrifugal experiments, a novel analytical basis using irreducible water defined by T2 cutoff value was proposed to quantitatively analyze the dynamic wetting mechanism under different CO2 pressures. The results show that when T2 < 72.32 ms, the water in coal is irreducible water; when T2 > 72.32 ms, the water in coal is movable water. CO2 pressure hindered free water conversion to adsorbed and capillary water, but impacted adsorbed water more. Increased CO2 pressure caused the wetting porosity of coal to decrease from 1.62 % to 1.08 %, and coal gradually changed from water-wet to CO2-wet. The increase in CO2 pressure enlarged the CO2 aggregations in the seepage channel, thus weakening the wetting rate of water to coal. CO2 preferentially occupied small pores, which will hinder the migration of water into small pore spaces. Molecular diffusion controls water to achieve wetting equilibrium more than gravity/pressure difference and capillary force. As CO2 pressure increases, the wetting equilibrium time decreases.

Semi-implicit schemes for modeling water flow and solute transport in unsaturated soils

The coupled model of water flow and solute transport in unsaturated soils is addressed in this study. Building upon previous research findings by Keita, Beljadid, and Bourgault, we investigate a class of second-order time-stepping techniques where two free parameters are introduced, to identify the most stable and accurate scheme. The spatial discretization of the Richards equation is accomplished using the mixed finite element method. The proposed approach involves formulating noniterative schemes using an extrapolation formula and Taylor approximation in time to linearize nonlinear terms. Additionally, a specialized regularization technique is applied to ensure the convergence of the proposed numerical methods. Numerical simulations are conducted to determine the optimal scheme for solving the Richards equation, which is subsequently extended to the transport equation.Numerical simulations of water flow reveal the good accuracy of three schemes—SBDF, MSBDF, and Richards-M2 for homogeneous and heterogeneous soils. Notably, the SBDF scheme stands out for its computational efficiency and stability, especially when gravity forces dominate over capillary forces. Through numerical analysis of the coupled semi-implicit schemes, our results affirm the SBDF scheme’s superior robustness, establishing it as the optimal choice among the proposed numerical methods. Therefore, the SBDF scheme is employed to solve the coupled model of water flow and solute transport. We conducted various numerical experiments to solve the coupled model, addressing scenarios including single and multispecies nitrogen transport, pore water electrical conductivity, and nitrate transport. The SBDF scheme’s accuracy was rigorously verified through comparisons with reference solutions and experimental data. This establishes the SBDF scheme as an efficient alternative to traditional implicit methods for modeling water flow and solute transport in unsaturated soils.

Effect of the advancing contact angle on coal particle–bubble detachment at the mesoscopic scale

Improving particle–bubble adhesion stability and reducing particle–bubble detachment are crucial in froth flotation processes. In this study, a nonequilibrium molecular dynamics approach is applied to investigate the dynamic detachment process of low-rank coal particles adhering with/without a collector from bubbles under different pull forces at the mesoscopic scale. Results indicate that a collector oil film on the surface of a low-rank coal particle can considerably increase the advancing contact angle and counteract the contraction of the three-phase contact line, enabling the particle to withstand a greater detachment force. Conversely, the residual water clusters on the particle surface tend to cause contraction of the contact line. Force analysis of the liquid surrounding the particle and the contact line indicates that the maximum static capillary force between the particle and the bubble is equivalent to the capillary force when the bending angle of the liquid surface reaches the advancing contact angle. When the bending angle of the liquid surface exceeds the forward contact angle, the force on the liquid around the contact line becomes unbalanced, causing the contact line to move to decrease the bending angle of the liquid surface and restore balance to the surrounding liquid. Hence, on mesoscopic scales of ten to tens of nanometers, the advancing contact angle still determines particle–bubble detachment. The study of particle–bubble detachment mechanisms at the mesoscopic scale is expected to establish a relation between microscopic mechanisms at the molecular scale and macroscopic experimental studies at the micrometer to millimeter scale

Pore-scale simulation of two-phase flow in biporous media

Enhancing both permeability and capillary pumping in porous structures has emerged as a key focus for researchers, leading to the development of biporous media. While experimental studies on these structures have been conducted recently, there is a lack of numerical simulations due to difficulties in describing the geometry. To address this gap, the present study explores pore-scale numerical simulation of two-phase capillary flow in biporous media. A new simplified biporous structure is proposed, featuring a staggered arrangement of clusters, with each cluster composed of closely packed solid particles. For comparison, a monoporous media case is contrasted and represented using a conventional staggered arrangement of solid particles. Both passive and active capillary flow modes are considered in the present study. The numerical results align well with previous experimental findings on biporous media, indicating that the proposed biporous geometry effectively models two-phase flow in complex structures at a reasonable computational cost. The results show that capillary effects in biporous media are up to two times more effective than in monoporous structures. Simultaneously, permeability is enhanced by a factor of four in biporous media under similar circumstances, with most of the mass flow rate (more than 95%) passing through the larger pores between clusters. This combined impact of increased capillary action and higher permeability leads to enhanced wicking performance in biporous structures. The outcomes can help to understand two-phase flow physics in the biporous structure and develop reliable models for the simulation of biporous media on a macroscopic scale. Numerical modeling and comprehension of capillary structures play a crucial role in designing optimized geometries to enhance their performance.