Aromatic Oil Research Articles

Direct elemental analysis of plant oils by inductively coupled plasma mass spectrometry: Simple sample dilution combined with oxygen introduction into the plasma

Assessment of trace metal concentrations in plant oils has been considered a crucial quality control marker for potential health risks, oil flavour, and oxidative stability. A straightforward inductively coupled plasma mass spectrometry (ICP-MS) methodology was developed and validated through introduction of argon:oxygen gas mixture into plasma, allowing for a direct elemental analysis of organic matrices. This approach offers the advantage of a simple one-step preparation of plant oil samples with negligible contamination risks. The complete solubilization of the oil matrix enables the determination of total metal content from a single test tube with low dilution factor of 5. The modified plasma conditions resulted in the development of a robust and accurate ICP-MS method providing limits of detection at sub ng·g−1 levels. The ICP-MS method allowed the determination of trace levels of Ba, Cd, Cu, Fe, Mn, Pb, Sn, V, and Zn in olive, sunflower and rapeseed oils.

Artifacts Associated with the Chemical Arts in the Early Islamic Period in Ramla, Israel

Archaeological excavations in Ramla, Jund Filastin capital during the early Islamic period, discovered in a zone of artisans and workshops, a unique complex of built and dug installations. It included barely known and understood components of a proto-chemical toolkit. The finds included an abundance of small, decorated bottles previously identified as perfume containers. Additional small finds of a proto-chemistry toolkit included e.g., bronze pipettes, delicate bronze pestles and weights. The complex is to be associated with the existence of a facility differing from an alchemist studio-laboratory. It involved the commercial, non-artisan, pre-industrial production of perfumes and aromatic oils associated with body care chemistry. The close proximity to a Hammam (bathhouse) is notable. Suitable comparisons were found throughout the Mediterranean Basin, from Spain, where comparable tool kits in close proximity to Hammams were discovered, to Russia, where similar technology and typology were documented. The article discusses the importance of the dictates of the Qur’an and Mohammedan traditions regarding purification of the body and their catalytic influence on social and early technological changes in a pre-industrial society.

Post-COVID syndrome: analysis of the prevalence of chemosensory dysfunction and predictive factors of recovery in COVID-19 long-haulers in Jordan.

One of the major concerns of the post-COVID-19 era is elucidating and addressing the long-term complications of COVID-19. A web-based questionnaire was distributed in Jordan to assess the prevalence and recovery from chemosensory dysfunction among COVID-19 long-haulers in Jordan. A total of 611 respondents complained of chemosensory dysfunction (age range = 18-68 years), and the majority of the respondents were female (88.4%). Parosmia was the most prevalent olfactory dysfunction reported (n = 337, 33.3%), and parageusia was the most frequently reported gustatory dysfunction (n = 239, 36.4%). Medications were not reported to be associated with a better perception of smell or taste by nearly half of those who had been treated (n = 146, 46.1%). Among participants who had received olfactory rehabilitation/training (n = 215, 35.2%), 43.7% (n = 94) reported modest improvement, with the most frequently helpful scents being coffee (n = 80, 24.8%), aromatic oils (n = 74, 23%), and perfumes/colognes (n = 73, 22.7%). Age was found to have a significant negative correlation with complete recovery. In addition, age (p < .05), anosmia (p < .001), hyperosmia (p < .001), ageusia (p < .05), and duration of olfactory dysfunction (p < .001) were all independent predictors of complete recovery. Chemosensory dysfunctions are largely subjective; therefore, more objective examinations are required to draw more definite conclusions.

Interfacial Adsorption of Oil-Soluble Kraft Lignin and Stabilization of Water-in-Oil Emulsions.

In this paper, the potential of esterified Kraft lignin as a novel oil-soluble surfactant was examined. The lignin was chemically modified by esterification with lauric or stearic acid, making it soluble in solvents such as toluene or n-decane. Adsorption at the oil-water interface was then studied by the Du Noüy ring-method. The oil-soluble lignin behaved similar to water-soluble lignin surfactants, both the qualitative and quantitative progression of interfacial tension. Modeling revealed a surface excess of 7.5-9.0 × 10-7 mol/m2, area per molecule of 185-222 Å2, and a diffusion coefficient within the range 10-10 to 10-14 m2/s; all of which are in line with existing literature on water-soluble lignosulfonates. The data further suggested that the pendant alkyl chains were extended well into the paraffinic solvent. At last, bottle tests showed that the oil-soluble lignin was able to stabilize oil-in-water emulsions. The emulsion stability was affected by the concentration of lignin or NaCl as well as the oil phase composition. Aromatic oils exhibited lower emulsion stability in comparison to the aliphatic oil. In conclusion, a new type of surfactant was synthesized and studied, which may contribute to developing green surfactants and novel approaches to valorize technical lignin.

Influence of Petroleum-Based and Bio-Derived Recycling Agents on High-RAP Asphalt Mixtures Performance

Reclaimed asphalt pavement (RAP) has been utilized as a potential partial substitute for virgin asphalt binder in asphalt mixtures. However, a primary concern with increasing RAP content in asphalt mixtures is the cracking potential, attributed to the aged RAP asphalt binder (RAP-binder). To address this, the use of petroleum-based and bio-derived recycling agents (RAs) in enhancing the cracking resistance of high-RAP asphalt mixtures has been explored. The objective of this study is to ascertain the effectiveness of six RAs in mitigating cracking in high-RAP asphalt mixtures. The RAs considered include petroleum-crude-oil-derived aromatic oil, soy oil, and four types of tall-oil-derived phytosterol (industrial by-product, intermediate, purified, and fatty acid-based). The RAs’ dosages were optimized, based on RAP-binder and unmodified asphalt binder properties, to produce target PG 70-22 asphalt binder when incorporated in asphalt mixtures containing 30% RAP. To assess the engineering performance of these 30%-RAP asphalt mixtures for each RA, a conventional asphalt mixture incorporating styrene-butadiene-styrene (SBS)-modified PG 70-22 asphalt binder without RAP or RAs was benchmarked for comparison. Mechanical tests performed included Hamburg wheel-track testing (HWTT), intermediate-temperature fracture tests (semi-circular bend, Illinois flexibility index, and IDEAL cracking tolerance), and thermal stress-restrained specimen tensile strength test to evaluate permanent deformation, intermediate-temperature cracking resistance, and low-temperature cracking resistance, respectively. Results showed that petroleum-crude-oil-derived aromatic oil and tall-oil-derived fatty-acid-based oil RAs were able to rejuvenate RAP-binder as measured by the cracking tests performed. Further, the use of these RAs did not adversely impact the asphalt mixtures’ permanent deformation performance.

Simultaneous removal of aliphatic and aromatic crude oil hydrocarbons by Pantoea agglomerans isolated from petroleum-contaminated soil in the west of Iran.

Hydrocarbons are considered as one of the most common and harmful environmental pollutants affecting human health and the environment. Bioremediation as an environmentally friendly, highly efficient, and cost-effective method in remediating oil-contaminated environments has been interesting in recent decades. In this study, hydrocarbon degrader bacterial strains were isolated from the highly petroleum-contaminated soils in the Dehloran oil field in the west of Iran. Out of 37 isolates, 15 can grow on M9 agar medium that contains 1.5 gL-1 of crude oil as the sole carbon source. The morphological, biochemical, and 16SrRNA sequencing analyses were performed for the isolates. The choosing of the isolates as the hydrocarbon degrader was examined by evaluating the efficacy of their crude oil removal at a concentration of 10gL-1 in an aqueous medium. The results showed that five isolates belonging to Pseudomonas sp., Pseudomonas oryzihabitans, Roseomonas aestuarii, Pantoea agglomerans, and Arthrobacter sp. had a hyper hydrocarbon-degrading activity and they could remove more than 85% of the total petroleum hydrocarbon (TPH) after 96h. The highest TPH removal of about 95.75% and biodegradation rate of 0.0997gL-1h-1 was observed for P. agglomerans. The gas chromatography-mass spectroscopy (GC-MS) analysis was performed during the biodegradation process by P. agglomerans to detect the degradation intermediates and final products. The results confirmed the presence of intermediates such as alcohols and fatty acids in the terminal oxidation pathway of alkanes in this biodegradation process. A promising P. agglomerans NB391 strain can remove aliphatic and aromatic hydrocarbons simultaneously.

Phytosome-conjugated carvacrol: A novel approach for improving growth performance, intestinal morphology and economics of production in Broiler Chicken

Essential oils are plant-derived aromatic volatile oils, and they contain bioactive compounds that have been shown to improve poultry nutrition. However, considering problems associated with the solubility and bioavailability of polyphenolic compounds, the study was planned to find out the effect of the novel feed-grade delivery system, phytosomes for conjugation of plant-derived polyphenolic compound carvacrol on the growth performance of broiler chickens. The experiment was conducted, on 240 broiler chicks for a period of 6 weeks. The chicks were divided into 4 groups having 4 replicates of 15 birds each. The birds in the control group (T0) offered a standard diet as per BIS (2007) specification. Group T1 received a standard diet supplemented with Bacitracin Methylene Disalicylate (BMD) antibiotic at standard dose and group T2 received a standard diet supplemented with carvacrol essential oil @100 mg/kg feed. Group T3 received a standard diet supplemented with phytosome-conjugated carvacrol essential oil (carvacrol @16.6%) @100 mg/kg feed. The performance of all the treatment groups was assessed with respect to the different performance parameters. The supplementation of phytosome-conjugated carvacrol essential oil (carvacrol @16.6%) @ 100 mg/kg feed was found beneficial in terms of growth performance, feed efficiency, and intestinal morphometry. In terms of economics of broiler production, the results revealed that the addition of phytosome- conjugated carvacrol essential oil and carvacrol essential oil in diets was found beneficial in reducing the cost of broiler production, thereby enhancing the margin of profit in broiler production and fetching higher net profit than the control group.

Vulcanization kinetics and reinforcement behaviour of natural rubber-carbon black composites: Addition of Shea-butter versus aromatic oil as plasticizers

This work is a comparative study between Shea butter (SB) and treated distillate aromatic extract oil (TDAE) as plasticizers in the vulcanization of natural rubber (NR)- carbon black (CB) vulcanizates (—CB—S—NR—). The plasticized —CB—S—NR— composites extended scorch (Ts2) and optimum (T90) curing times. The delays in crosslinking reaction were suspected to be due to the increased viscosity (ML) and insulation of the reacting species (NR, CB, Sulfur and other curing aids) by the films of plasticizers. This effect increased the activation energy (Ea (KJ/mol)) for vulcanization. The —CB—S—NR— without plasticizer SB (SBO), showed higher ML, crosslinking density index (ΔM), rheological strength (MH) and low cure reversion properties than others. In comparison, the SB loaded —CB—S—NR— composites showed improvement in ML, ΔM, T90, with lowers Ea (KJ/mol) than TDAE samples. Also, the SB compounds exhibited higher Young's modulus Eo(MPa) than SBO and TDAE compounds. For instance, the Eo(MPa) of SB5 was over 7 and 1200 % higher than SBO and STD5 respectively. However, —CB—S—NR— filled with TDAE generally showed higher strength(MPa), attributed to stronger CB—NR interactions. Therefore, environmentally friendly SB could replace petroleum based oils for compounding rubbers.

Geochemical Characteristics of Mesoproterozoic Source Rocks in North China: Insights for Organic Matter Enrichment and Thermal Evolution

In recent years, the exploration of oil and gas in China’s Precambrian strata has garnered significant attention, leading to notable advancements in exploration play assessment. However, there is a dearth of published literature on Proterozoic source rocks’ organic sources, sedimentary environments, marine hydrochemistry, and other attributes. This study focuses on investigating potential source rocks within the Hongshuizhuang and Xiamaling Formations in the Jibei Depression of North China. A comprehensive analysis was conducted to evaluate hydrocarbon generation characteristics, using hydrocarbon biomarkers and polar compounds as geochemical indicators for precursor biota and maturity levels. The results indicate high organic matter abundance with predominantly type I-II1 organic matter composition in the studied source rocks. These samples are at an immature–low mature stage, with the potential for primarily generating aromatic crude oil. The parent material is mainly attributed to lower aquatic organisms, such as bacteria and algae. The sedimentary environment exhibits marine facies, characterized by high evaporation rates, salinity levels, and strong euxinic conditions, that led to sulfur incorporation into the organic matter matrix. It should be noted that correlations between biomarker parameters and maturity may not be fully applicable to ancient source rocks; however, the methyldibenzothiophene ratio (MDR) demonstrates a strong correlation with Tmax. The compounds and their total monoisotope ions abundance (TMIA) were primarily identified and analyzed using FT–ICR MS. It was observed that these compounds were influenced by the depositional environment and organic matter maturity. Importantly, it was clearly demonstrated that the DBE and carbon number range of CH compounds gradually increased with maturity, due to the removal of N, S, and O functional groups. Specifically, N1 compounds predominantly consisted of carbazoles with short alkyl side chains which readily converted into N1Ox compounds. On the other hand, O1 compounds mainly comprised benzofurans with low abundance, indicating a reducing sedimentary environment, as suggested by their low TMIA values. Furthermore, S1 compounds were primarily thiophenes whose DBE range and carbon number increased with maturity, possibly suggesting an abiotic input of inorganic sulfur. Notably, the maturity indices (MAT) proved suitable for Mesoproterozoic source rocks while exhibiting strong linear relationships.

EFFECT OF SOAKING WITH ATONIC, WATER HYACINTHS COMPOST AND BIOFERTILIZERS ON VEGETATIVE AND FLOWERING GROWTH OF TUBEROSE

This study was aimed to investigate effect of soaking Polianthes tuberosa L. bulbs in Atonic solution and inoculation with Stenotrophomonas maltophilia and Glomus mosseae, and fertilizing with two levels (3% and 4%) of water hyacinths Compost on some vegetative and floral growth characters of the Peral variety of tuberose plants in a Factorial experiment during spring season of 2022 using a randomized completely block design with three replicates. Tuberose bulbs were planted in black plastic bags containing 6 kg of a sandy loam soil. The results of the three-way interaction showed that the treatment of soaking with Atonic, inoculation with the combination of the biofertilizer, and fertilization with 4% level of water hyacinths Compost significantly outperformed other treatments in plant height, number of inflorescences, dry weight of flowers, vase life, and aromatic oil concentration with values of 47.33 cm, 55.33 inflorescences plant-1, 5.78 grams, 16 days,and 0.71% respectively, compared to the control treatment which resulted in values of 21.67 cm, 5.67 inflorescences plant-1, 1.81 grams, 8 days,and 0.42% respectively.

Flavor enhancement of strong fragrant rapeseed oils by enzymatic treatment

Fragrant rapeseed oils with the sensory characteristics attract increasing market in China. The unique flavor of strong fragrant rapeseed oil (SFRO) is the first choice to attract the consumers’ preference. Thus, enzymatic treatments of rapeseeds were used to enhance the flavor properties of SFROs in the present study. Results showed that SFRO produced from neutral protease and α-amylase-treated rapeseeds (NRO+ARO) had the highest percentages of unsaturated fatty acid (USFA), monounsaturated fatty acid (MUSFA) and oleic acid (C18:1) of 93.30%, 65.90% and 65.22%, respectively, with the highest tocopherol content of 577.35 mg/kg and total sterol content of 4523.46 mg/kg. The NRO+ARO showed a strong nutty and rich roasted fragrance and distinguishing sweet flavor with the highest overall sensory evaluation score. Majority of volatile compounds in NRO+ARO belonged to pyrazines and furans originated from Maillard reactions with the highest contents. The highest decrease trends of monosaccharide and amino acid contents from 8.42 g/kg to 2.04 g/kg and from 128.91 mg/kg to 47.39 mg/kg, respectively, were observed in the neutral protease and α-amylase-treated rapeseeds after roasting. Glucose/xylose-lysine reaction products contained the high contents of pyrazines, suggesting enhancement of supply of glucose/xylose and lysine in rapeseeds would significantly improve the fragrance of SFROs. The outputs of present study would provide a clue to understand the formation of unique flavor of SFROs and a reference to develop series of SFRO products.

Contribution of lipid to the formation of characteristic volatile flavor of peanut oil

Lipid is an important precursor for volatile flavor formation, but it is not clear how to study the reactions involved in forming key volatile flavor compounds in peanut oil. In this paper, we innovatively established a flavor research model to investigate the contribution of different chemical reactions to the aroma compounds of peanut oil. The results showed that lipid participation in thermal reactions is necessary for forming major aroma compounds in hot-pressed peanut oil. Compared to the Maillard reaction, the lipid oxidation-Maillard reaction produces more compounds with 46 volatile substances identified. During the heating process, six new key substances were formed and the level of unsaturated fatty acids decreased by 7.28%. Among them, linoleic acid may be an important precursor for the formation of aroma components of hot-pressed peanut oil. Our study could provide theoretical guidance for understanding the volatile flavor mechanism of peanut oil and improving volatile flavor.

Degradation of Plastic Materials through Small-Scale Pyrolysis: Characterization of the Obtained Hydrocarbons and Life Cycle Analysis

Plastic waste signifies a global predicament, aggravated by deficient management practices. Unearthing methods to repurpose energy from this waste is pivotal. This study delves into the pyrolytic degradation of low-density plastics to convert plastic waste into valuable products on a modest scale. A small-scale, low-CO2 emitting distiller was employed in the process. A zeolite was harnessed as a catalyst to augment the temperature and hasten the pyrolysis process. A comprehensive life cycle analysis was executed to assess the environmental impact of the process. In this scenario, zeolite-facilitated pyrolysis was more proficient compared to traditional thermal pyrolysis, generating a yield of 22.5% with the catalyst, contrasting with 18% without. A kinetic model was formulated, observing reaction mechanisms and temperature escalation and culminating in the extraction of aromatic oils. These oils were further distilled to produce liquid hydrocarbons, beginning the distillation at 60 °C with the catalyst. Characterization of the secured hydrocarbons was conducted using infrared, Raman spectroscopy, and gas chromatography, discovering compounds akin to gasoline, such as benzene, toluene, and xylenes. Additionally, the procedure exhibited a minimal environmental detriment, as validated by the life cycle analysis. This study concludes by highlighting the potential of small-scale, low-CO2 emitting pyrolytic degradation of low-density plastics for energy recovery from plastic waste, demonstrating the practical and environmental benefits of this avant-garde method.

Evaluation of industrial aromatic oils as potential hydrogen carriers: Study of the hydrogenation step

Industrial organic streams (oils) with high concentration of aromatics compounds are present in different carbochemical and petrochemical processes. These aromatic compounds are potential hydrogen carriers through hydrogenation-dehydrogenation cycles. For this purpose, catalytic hydrogenation of three different aromatic oils using conventional hydrogenation catalysts is considered in this work. Two oil samples (petrochemical Oil A and carbochemical Oil B) enriched with polyaromatic compounds, along with a manufactured oil of petrochemical origin (SolvessoTM 200), were hydrogenated using Pt/γ-Al2O3 and Pd/γ-Al2O3 catalysts. The study aims to work under mild conditions to avoid secondary reactions and cracking, which is important for using these oils as potential LOHCs. The methodology involved using a stainless-steel autoclave reactor and analysing the composition of the oils and reaction products using gas chromatography and mass spectrometry. Diaromatic compounds were found to be the most reactive, reactant conversion depending on the catalyst and reaction temperature. However, the presence of tri and tetra-aromatic compounds hinder the reaction. Moreover, nitrogenated aromatic compounds are extremely reactive at these conditions. Comparison of SolvessoTM 200 with benzyltoluene, an established LOHC, resulted in promising results. Thus, both Oil A and B, after a purification step, would have interesting qualities to be used as LOHCs with the added advantage of its low price.

Aromatic oil from lavender as an atopic dermatitis suppressant.

In atopic dermatitis (AD), nerves are abnormally stretched near the surface of the skin, making it sensitive to itching. Expression of neurotrophic factor Artemin (ARTN) involved in such nerve stretching is induced by the xenobiotic response (XRE) to air pollutants and UV radiation products. Therefore, AD can be monitored by the XRE response. Previously, we established a human keratinocyte cell line stably expressing a NanoLuc reporter gene downstream of XRE. We found that 6-formylindolo[3,2-b]carbazole (FICZ), a tryptophan metabolite and known inducer of the XRE, increased reporter and Artemin mRNA expression, indicating that FICZ-treated cells could be a model for AD. Lavender essential oil has been used in folk medicine to treat AD, but the scientific basis for its use is unclear. In the present study, we investigated the efficacy of lavender essential oil and its major components, linalyl acetate and linalool, to suppress AD and sensitize skin using the established AD model cell line, and keratinocyte and dendritic cell activation assays. Our results indicated that lavender essential oil from L. angustifolia and linalyl acetate exerted a strong AD inhibitory effect and almost no skin sensitization. Our model is useful in that it can circumvent the practice of using animal studies to evaluate AD medicines.

Study on the Crystallization Behavior of Neodymium Rare-Earth Butadiene Rubber Blends and Its Effect on Dynamic Mechanical Properties.

Utilizing neodymium-based butadiene rubber as a baseline, this study examines the effect of eco-friendly aromatic TDAE oil, fillers, and crosslinking reactions on neodymium-based rare-earth butadiene rubber (Nd-BR) crystallization behavior. The findings suggest that TDAE oil hinders crystallization, resulting in decreased crystallization temperatures and heightened activation energies (Ea). The crystallization activation energies for 20 parts per hundreds of rubber (PHR) and 37.5 PHR oil stand at -116.8 kJ/mol and -48.1 kJ/mol, respectively, surpassing the -264.3 kJ/mol of the unadulterated rubber. Fillers act as nucleating agents, hastening crystallization, which in turn elevates crystallization temperatures and diminishes Ea. In samples containing 20 PHR and 37.5 PHR oil, the incorporation of carbon black and silica brought the Ea down to -224.9 kJ/mol and -239.1 kJ/mol, respectively. Crosslinking considerably restricts molecular motion and crystallization potential. In the examined conditions, butadiene rubber containing 37.5 PHR oil displayed no crystallization following crosslinking, albeit crystallization was discernible with filler inclusion. Simultaneously, the crystallinity level sharply declined, manifesting cold crystallization behavior. The crosslinking process elevates Ea, while the equilibrium melting point (Tm0) noticeably diminishes. For instance, the Tm0 of pure Nd-BR is approximately -0.135 °C. When blended with carbon black and silica, the Tm0 values are -3.13 °C and -5.23 °C, respectively. After vulcanization, these values decrease to -21.6 °C and -10.16 °C. Evaluating the isothermal crystallization kinetics of diverse materials via the Avrami equation revealed that both the oil and crosslinking process can bring about a decrease in n values, with the Avrami index n for various samples oscillating between 1.5 and 2.5. Assessing the dynamic mechanical attributes of different specimens reveals that Nd-BR crystallization notably curtails its glass transition, marked by a modulus shift in the transition domain and a decrement in loss factor. The modulus in the rubbery state also witnesses a substantial augmentation.

Physical-Rheological Properties and Performances of Rejuvenated (Styrene-Butadiene-Styrene) Asphalt with Polymerized-MDI and Aromatic Oil

Physical-Rheological Properties and Performances of Rejuvenated (Styrene-Butadiene-Styrene) Asphalt with Polymerized-MDI and Aromatic Oil

Antimicrobial Activity of Aromatic Herb Essential Oils against Pseudomonas aeruginosa

Antimicrobial Activity of Aromatic Herb Essential Oils against Pseudomonas aeruginosa

Organosiloxane membranes for heavy aromatic oil fractionation.

The industrial separation of hydrocarbons relies on distillation. Organic solvent nanofiltration can provide an energy-efficient alternative. We prepared high performance organosiloxane membranes for fractionation of heavy aromatics. They achieved a high permeance up to 0.13 L m-2 h-1 bar-1, with a rejection rate of 88.7% for hydrocarbons with five aromatic rings.

아로마 오일을 이용한 두피스케일링의 모발 및 두피 상태 개선 효과

아로마 오일을 이용한 두피스케일링의 모발 및 두피 상태 개선 효과