Flat Detector CT Research Articles

Denoising and artefact reduction in dynamic flat detector CT perfusion imaging using high speed acquisition: first experimental and clinical results

Flat detector CT perfusion (FD-CTP) is a novel technique using C-arm angiography systems for interventional dynamic tissue perfusion measurement with high potential benefits for catheter-guided treatment of stroke. However, FD-CTP is challenging since C-arms rotate slower than conventional CT systems. Furthermore, noise and artefacts affect the measurement of contrast agent flow in tissue. Recent robotic C-arms are able to use high speed protocols (HSP), which allow sampling of the contrast agent flow with improved temporal resolution. However, low angular sampling of projection images leads to streak artefacts, which are translated to the perfusion maps. We recently introduced the FDK-JBF denoising technique based on Feldkamp (FDK) reconstruction followed by joint bilateral filtering (JBF). As this edge-preserving noise reduction preserves streak artefacts, an empirical streak reduction (SR) technique is presented in this work. The SR method exploits spatial and temporal information in the form of total variation and time-curve analysis to detect and remove streaks. The novel approach is evaluated in a numerical brain phantom and a patient study. An improved noise and artefact reduction compared to existing post-processing methods and faster computation speed compared to an algebraic reconstruction method are achieved.

Treatment of supratentorial spontaneous intracerebral hemorrhage using image-guided minimally invasive surgery: Initial experiences of a flat detector CT-based puncture planning and navigation system in the angiographic suite.

The intracerebral hemorrhage drainage through minimally invasive approach is emerging as an alternative for traditional craniotomy, due to its improved survival rate and reduced complication rate. In this study, we investigated the feasibility and safety of a flat detector CT-based puncture planning and navigation system for minimally invasive hematoma drainage on patients with intracerebral hemorrhage. The minimally invasive hematoma drainage was performed on 21 hypertensive patients with intracerebral hemorrhage in the angiographic suite with the guidance of a flat detector CT-based puncture planning and navigation system. This system is integrated in the angiographic machine, and was used for 1) planning the needle path based on a preprocedural flat detector CT scan, 2) advancing the catheter with real-time fluoroscopic guidance, and 3) confirming the procedure outcome based on an immediate postprocedural flat detector CT. The surgery efficiency, accuracy, and the treatment outcome were measured and compared with the published data. All procedures were successfully completed with the catheter placed 4 ± 1 mm from the planned position. The average surgery time was 40 ± 7 minutes. The volume of the hematoma was reduced to 28 ± 4% of the original volume. The Glasgow Coma Scale score was significantly improved from 10 ± 1 at the admission to 14 ± 1 at the discharge. The Extended Glasgow Coma Scale score also improved from 5 ± 1 at the discharge to 6 ± 1 at the 6-month follow-up. No major complication, rebleeding, and mortality were observed in this study. This flat detector CT-based needle guidance system provided a feasible, convenient, and safe way to perform the puncture and drainage of brain hematoma in the angiographic suite.

Flat detector angio-CT following intra-arterial therapy of acute ischemic stroke: identification of hemorrhage and distinction from contrast accumulation due to blood-brain barrier disruption.

Flat panel detector CT in the angiography suite may be valuable for the detection of intracranial hematomas; however, abnormal contrast enhancement frequently mimics hemorrhage. We aimed to assess the accuracy of flat panel detector CT in detecting/excluding intracranial bleeding after endovascular stroke therapy and whether it was able to reliably differentiate hemorrhage from early blood-brain barrier disruption. Seventy-three patients were included for retrospective evaluation following endovascular stroke therapy: 32 after stent-assisted thrombectomy, 14 after intra-arterial thrombolysis, and 27 after a combination of both. Flat panel CT images were assessed for image quality and the presence and type of intracranial hemorrhage and BBB disruption by 2 readers separately and in consensus. Follow-up by multisection head CT, serving as the reference standard, was evaluated by a single reader. Conventional head CT revealed intracranial hematomas in 12 patients (8 subarachnoid hemorrhages, 7 cases of intracerebral bleeding, 3 SAHs plus intracerebral bleeding). Image quality of flat panel detector CT was considered sufficient in all cases supratentorially and in 92% in the posterior fossa. Regarding detection or exclusion of intracranial hemorrhage, flat panel detector CT reached a sensitivity, specificity, positive and negative predictive values, and accuracy of 58%, 85%, 44%, 91%, and 81%, respectively. Maximum attenuation measurements were not valuable for the differentiation of hemorrhage and BBB disruption. Flat panel CT after endovascular stroke treatment was able to exclude the rare event of an intracranial hemorrhage with a high negative predictive value. Future studies should evaluate the predictive value of BBB disruptions in flat panel detector CT for the development of relevant hematomas.

Hepatic Blood Volume Imaging with the Use of Flat-Detector CT Perfusion in the Angiography Suite: Comparison with Results of Conventional Multislice CT Perfusion

PurposeTo prospectively determine the feasibility of flat-detector (FD) computed tomography (CT) perfusion to measure hepatic blood volume (BV) in the angiography suite in patients with hepatocellular carcinoma (HCC). Materials and MethodsTwenty patients with HCC were investigated with conventional multislice and FD CT perfusion. CT perfusion was carried out on a multislice CT scanner, and FD CT perfusion was performed on a C-arm angiographic system, before transarterial chemoembolization procedures. BV values of conventional and FD CT perfusion were measured within tumors and liver parenchyma. The arterial perfusion portion of CT perfusion BV was extracted from CT perfusion BV by multiplying it by a hepatic perfusion index. Relative values (RVs) for CT perfusion arterial BV and FD CT perfusion BV (FD BV) were defined by dividing BV of tumor by BV of parenchyma. Relationships between BV and RV values of these two techniques were analyzed. ResultsIn all patients, both perfusion procedures were technically successful, and all 33 HCCs larger than 10 mm were identified with both imaging methods. There were strong correlations between the absolute values of FD BV and CT perfusion arterial BV (tumor, r = 0.903; parenchyma, r = 0.920; both P < .001). Bland–Altman analysis showed a mean difference of −0.15 ± 0.24 between RVs for CT perfusion arterial BV and FD BV. ConclusionsThe feasibility of FD CT perfusion to assess BV values of liver tumor and surrounding parenchyma in the angiographic suite was demonstrated.

Effective dose to patient measurements in flat-detector and multislice computed tomography: a comparison of applications in neuroradiology

Flat-detector CT (FD-CT) is used for a variety of applications. Additionally, 3D rotational angiography (3D DSA) is used to supplement digital subtraction angiography (DSA) studies. The aim was to measure and compare the dose of (1) standard DSA and 3D DSA and (2) analogous FD-CT and multislice CT (MSCT) protocols. Using an anthropomorphic phantom, the effective dose to patients (according to ICRP 103) was measured on an MSCT and a flat-detector angiographic system using standard protocols as recommended by the manufacturer. (1) Evaluation of DSA and 3D DSA angiography protocols: ap.-lat. Standard/low-dose series 1/0.8 mSv, enlarged oblique projection 0.3 mSv, 3D DSA 0.9 mSv (limited coverage length 0.3 mSv). (2) Comparison of FD-CT and MSCT: brain parenchyma imaging 2.9 /1.4 mSv, perfusion imaging 2.3/4.2 mSv, temporal bone 0.2 /0.2 mSv, angiography 2.9/3.3 mSv, limited to the head using collimation 0.5/0.5 mSv. The effective dose for an FD-CT application depends on the application used. Using collimation for FD-CT applications, the dose may be reduced considerably. Due to the low dose of 3D DSA, we recommend using this technique to reduce the number of DSA series needed to identify working projections. Effective dose of FD-CT in comparison to MSCT is in comparable range. Collimation decreases the dose of FD-CT effectively. Effective dose of 3-D angiography is identical to 2-D DSA. Different FD-CT programs have different dose.

Role of C-Arm VasoCT in the Use of Endovascular WEB Flow Disruption in Intracranial Aneurysm Treatment

The WEB aneurysm embolization system is still under evaluation but seems to be a promising technique to treat wide-neck bifurcation aneurysms. However, this device is barely visible using conventional DSA; thus, high-resolution contrast-enhanced flat panel detector CT (VasoCT) may be useful before detachment to assess the sizing and positioning of the WEB. The purpose of this study was to evaluate the interest of VasoCT during WEB procedures. From March 2012 to July 2013, twelve patients (10 women and 2 men; age range, 44-55 years) were treated for 13 intracranial aneurysms with the WEB device. DSA and VasoCT were used and compared to depict any protrusion of the device in parent arteries before detachment. Two neuroradiologists reviewed each VasoCT scan, and the quality was graded on a subjective quality scale. The mesh of the WEB was very well-depicted in all cases, allowing a very good assessment of its deployment. Device protrusion was clearly detected with VasoCT in 5 cases, leading to WEB repositioning or size substitution. During follow-up, VasoCT also allows good assessment of eventual residual blood flow inside the aneurysm or the WEB device. Unlike DSA, VasoCT is an excellent tool to assess WEB deployment and positioning. In our experience, it allowed a precise evaluation of the WEB sizing and its relation to the parent vessel. Such information very likely enhances the ability to safely use this device, avoiding potential thromboembolic events in cases of protrusion in the parent arteries.

Artifact Reduction of Different Metallic Implants in Flat Detector C-Arm CT

Flat detector CT has been increasingly used as a follow-up examination after endovascular intervention. Metal artifact reduction has been successfully demonstrated in coil mass cases, but only in a small series. We attempted to objectively and subjectively evaluate the feasibility of metal artifact reduction with various metallic objects and coil lengths. We retrospectively reprocessed the flat detector CT data of 28 patients (15 men, 13 women; mean age, 55.6 years) after they underwent endovascular treatment (20 coiling ± stent placement, 6 liquid embolizers) or shunt drainage (n = 2) between January 2009 and November 2011 by using a metal artifact reduction correction algorithm. We measured CT value ranges and noise by using region-of-interest methods, and 2 experienced neuroradiologists rated the degrees of improved imaging quality and artifact reduction by comparing uncorrected and corrected images. After we applied the metal artifact reduction algorithm, the CT value ranges and the noise were substantially reduced (1815.3 ± 793.7 versus 231.7 ± 95.9 and 319.9 ± 136.6 versus 45.9 ± 14.0; both P < .001) regardless of the types of metallic objects and various sizes of coil masses. The rater study achieved an overall improvement of imaging quality and artifact reduction (85.7% and 78.6% of cases by 2 raters, respectively), with the greatest improvement in the coiling group, moderate improvement in the liquid embolizers, and the smallest improvement in ventricular shunting (overall agreement, 0.857). The metal artifact reduction algorithm substantially reduced artifacts and improved the objective image quality in every studied case. It also allowed improved diagnostic confidence in most cases.

Use of time attenuation curves to determine steady-state characteristics before C-arm CT measurement of cerebral blood volume

Cerebral blood volume (CBV) measurement by flat panel detector CT (FPCT) in the angiography suite seems to be a promising tool for patient management during endovascular therapies. A steady state of contrast agent distribution is mandatory during acquisition for accurate FPCT CBV assessment. To the best of our knowledge, this was the first time that steady-state parameters were studied in clinical practice. Before the CBV study, test injections were performed and analyzed to determine a customized acquisition delay from injection for each patient. Injection protocol consisted in the administration of 72 mL of contrast agent material at the injection rate of 4.0 mL/s followed by a saline flush bolus at the same injection rate. Peripheral or central venous accesses were used depending on their availability. Twenty-four patients were treated for different types of neurovascular diseases. Maximal attenuation, steady-state length, and steady-state delay from injection were derived from the test injections' time attenuation curves. With a 15 % threshold from maximum attenuation values, average steady-state duration was less than 10 s. Maximum average steady-state duration with minimal delay variation was obtained with central injection protocols. With clinically acceptable contrast agent volumes, steady state is a brief condition; thus, fast rotation speed acquisitions are needed. The use of central injections decreases the variability of steady-state's delay from injection. Further studies are needed to optimize and standardize injection protocols to allow a larger diffusion of the FPCT CBV measurement during endovascular treatments.

Prior‐based artifact correction (PBAC) in computed tomography

Image quality in computed tomography (CT) often suffers from artifacts which may reduce the diagnostic value of the image. In many cases, these artifacts result from missing or corrupt regions in the projection data, e.g., in the case of metal, truncation, and limited angle artifacts. The authors propose a generalized correction method for different kinds of artifacts resulting from missing or corrupt data by making use of available prior knowledge to perform data completion. The proposed prior-based artifact correction (PBAC) method requires prior knowledge in form of a planning CT of the same patient or in form of a CT scan of a different patient showing the same body region. In both cases, the prior image is registered to the patient image using a deformable transformation. The registered prior is forward projected and data completion of the patient projections is performed using smooth sinogram inpainting. The obtained projection data are used to reconstruct the corrected image. The authors investigate metal and truncation artifacts in patient data sets acquired with a clinical CT and limited angle artifacts in an anthropomorphic head phantom data set acquired with a gantry-based flat detector CT device. In all cases, the corrected images obtained by PBAC are nearly artifact-free. Compared to conventional correction methods, PBAC achieves better artifact suppression while preserving the patient-specific anatomy at the same time. Further, the authors show that prominent anatomical details in the prior image seem to have only minor impact on the correction result. The results show that PBAC has the potential to effectively correct for metal, truncation, and limited angle artifacts if adequate prior data are available. Since the proposed method makes use of a generalized algorithm, PBAC may also be applicable to other artifacts resulting from missing or corrupt data.

Feasibility Study of Perfusion Imaging Using Flat Detector CT with an Intra-Arterial Injection Protocol Compared to Conventional Multi-Slice Perfusion CT with an Intravenous Injection Protocol

This study investigated the feasibility of using intra-arterial injection-based cerebral blood volume (CBV) imaging with flat detector computed tomography (CT, IAFD-CBV). It is proven that this new method could provide comparable physiologic information as standard intravenous injection-based multi-slice computed tomography CBV imaging (IVCT-CBV). Twelve patients were examined using both IAFD-CBV and IVCT-CBV. An experienced neuroradiologist read both sets of generated CBV maps. If a physiologic perfusion disorder was detected in standard IVCT-CBV, the focus was to check whether IAFD-CBV indicated the same disorder or not. Otherwise, if no disorder was detected, relative CBV (rCBV) values at different basal ganglia regions were measured for both CBV maps and then compared. For three patients with lesions, IAFD-CBV and IVCT-CBV showed similar perfusion disorders in the corresponding regions. For nine patients without lesions, both CBV maps showed good symmetry of contrast agent (CA) distribution for left/right hemisphere, the total average of rCBV was found to be 0.94 -/+0.18 and 1.01 -/+0.14 (1.0 for perfect symmetry) in IAFD-CBV and IVCT-CBV, respectively. However, compared to IVCT-CBV, IAFD-CBV imaging required 70% less contrast agent (CA). In general, a good correlation between IAFD-CBV and IVCT-CBV was found for all 12 patients. Minor deviations of IAFD-CBV were only detected at regions supplied by the middle cerebral artery. IAFD-CBV imaging, which can be directly performed in a catheterization laboratory, was proven to be technically feasible for real-time CBV assessment of the whole brain with good accuracy, and minimized CA usage.

Integrated flat detector CT and live fluoroscopic-guided external ventricular drain placement within the neuroangiography suite

PurposeTo demonstrate the feasibility of the application of integrated flat detector (FD) CT and fluoroscopic guidance (iGuide) for the placement of external ventricular drains (EVD) within the neuroangiography suite.MethodsA retrospective...

3:30 PM Abstract No. 52 - Outcome of endovascular treatment for aneurysmal bone cysts

Purpose Surgical management of aneurysmal bone cysts (ABCs) is associated with perioperative morbidity, mortality and high recurrence. In addition, some ABCs are inoperable. We evaluated the presentation, morphology, technique and outcome of percutaneous image guided sclerotherapy for ABCs. Materials and Methods We retrospectively reviewed the medical records and imaging studies of patients with ABCs who underwent percutaneous sclerotherapy at our institution. Age, location, size, symptoms, image guidance, agents used and outcomes were documented. Symptomatic and radiological changes were evaluated and compared pre and post sclerotherapy. Results 27 pts (5-18 yrs; mean age, 11.5 yrs) including 20 nonspinal ABCs (5-18 yrs; mean age, 11.5 years) and 7 spinal ABCs (8-18 yrs; mean age, 13 yrs) underwent percutaneous sclerotherapy. Most common symptoms were pain, swelling and neurological. 21 pts had biopsy proven ABCs. Sonographic, fluoroscopic or C-arm flat-detector CT (dynaCT) as well as combinations of these modalities was used for guidance. The sclerosant agents were sodium tetradecyl sulfate (n=23), ethanol (n=12) and doxycycline (n=8); either singly or in combinations. In 7 pts (4 nonspinal, 3 spinal) sclerotherapy was combined with transarterial embolization.1-9 sclerotherapy sessions were performed (mean: 5). Range of follow-up was 2-69 (mean, 35.5) months. In 17 (85%) nonspinal and 4 (71%) spinal lesions, pain resolved, completely in 16 pts (14 nonspinal and 2 spinal) and partially in 10 pts (5 non-spinal and 5-spinal). Radiological regression was noted in 14 (70%) nonspinal and 3 (43%) spinal lesions. 3 other pts with spinal ABCs showed radiological progression and spinal instability. 6 pts (5 spinal, 1 nonspinal) required further operative interventions but with significantly lesser blood loss. There were no complications related to sclerotherapy. Conclusion Endovascular treatment is a safe and effective treatment for aneurysmal bone cysts. It can be used as definitive treatment or as a bridge to elective surgical operation. This approach provides symptomatic relief and regression of the size of most ABCs, with more favorable outcome in nonspinal lesions.

Management of spinal epidural arteriovenous fistulas: interventional techniques and results

BackgroundSpinal epidural arteriovenous fistulas (SEDAVF) are rare and poorly understood clinical entities.Materials and methodsWe report a series of five (three men, two women) consecutive cases treated at our center to...

Flachdetektor-Computertomografie in der diagnostischen und interventionellen Kinderkardiologie

In this study the use of flat detector computed tomography (FD-CT) in the catheterization of patients with congenital heart disease was evaluated. Application reports were created for various issues based on the achieved image quality in diverse anatomical regions. FD-CT was applied in 176 cases during catheterization between January 2010 and April 2012. A five-point Likert scale ("essential" to "misleading") was used to evaluate image quality. All cases were analyzed retrospectively and application reports for the visualization of the aorta, pulmonary arteries, pulmonary veins, semilunar valves, cavopulmonary connections and atrial baffles were generated. Contrast dye consumption and radiation dose were evaluated. During the observation period FD-CT was applied in all 176 cases. The mean patient age was 7.0 years (0.01 - 42.53 years). The clinical value of FD-CT was rated superior to conventional angiography in 96.6 % of the cases and was never rated as "misleading". FD-CT was rated "essential" in 3.4 % of all cases, "very useful" in 77.3 % of all cases, "useful" in 15.9 % of all cases and "not useful" in 3.4 % of all cases. The mean dose-area product was 99 µGym2 (19.3 - 1276.6 µGym2), and the used contrast dye was 1.76 ml/kg (0.9 - 5 ml/kg). Application reports for the visualization of different anatomical regions are demonstrated. FD-CT is a new and auxiliary procedure in diagnostic and interventional catheterization of patients with congenital heart disease. Particularly extracardiac structures can be displayed in three-dimensional high resolution and be used for diagnosis, surgical planning and 3 D navigation.

Abstract 176: The Feasibility of Intravenous Flat-Detector CT (IV FDCT) Angiography for Intracranial Arterial Stenosis

BACKGROUND AND PURPOSE: Intravenous flat-detector CT (IV FDCT) angiography is an emerging technology for the detection of intracranial vascular disease. The study was conducted to determine the feasibility of IV FDCT in estimating major atherosclerotic intracranial arteries stenosis with digital subtraction angiography (DSA) as the reference. METHODS: DSA and IV FDCT were performed simultaneously in patients with transient ischemic attack or acute cerebral infarction. The degree and length of stenosis were measured. The stenotic vessels were categorized into four groups by the grade of stenosis: normal (&lt;30%), mild (30-49%), moderate (50-69%) or severe (&gt;70%). The vessels of the normal group were excluded from analysis to reduce spectrum bias. Measurement of vessels was recorded using an electric ruler by a qualified endovascular neurosurgeon and a neuroradiologist. RESULTS: A total of sixty-nine patients with 842 vessel segments were calculated. Mild (n=56), moderate (n=47) and severe stenosis (n=46) groups were analyzed. IV FDCT had a sensitivity of 97.6%, specificity of 96.9%, and a negative predictive value of 96.9% for detecting ≥50% stenosis and respective values of 91.9%, 98.2%, and 97.4 % for depicting ≥70% stenosis. The difference of stenotic length between two tests was not significantly difference as an increase in the severity of stenosis (Spearman’s rank test; r = - 0.12, p=0.13) CONCLUSION: IV FDCT can be a feasible alternative as a noninvasive method for evaluating stenosis of the major intracranial arteries.

Intravenous Flat-Detector Computed Tomography Angiography for High-Grade Carotid Stenosis

The significant feature of intravenous flat-detector computed tomography (IV FDCT) angiography is its role in neurointerventional setting without patient transfer. However, few studies have addressed the accuracy of IV FDCT in estimating carotid stenosis and length. This study examined the reliability of IV FDCT in the diagnosis of high-grade carotid stenosis and stenosis length with digital subtraction angiography (DSA) as the reference. Intravenous flat-detector CT and DSA were conducted simultaneously for 33 patients with 42 stenosed carotid arteries who were suspected of having symptomatic high-grade stenosis by carotid duplex ultrasound, magnetic resonance angiography, or CT angiography. The degree of stenosis and length discrepancy between 2 tests were recorded by 2 readers. The intraobserver and interobserver agreements were excellent for measuring high-grade carotid stenosis (κ = 0.87 and 0.82). Intravenous flat-detector CT had a sensitivity of 96.3%, specificity of 93.3%, and negative predictive value of 93.3% for detecting high-grade stenosis (≥70%) compared with DSA. Bland-Altman plots demonstrated excellent correlation of the degree of stenosis IV FDCT with DSA. Length discrepancy (IV FDCT - DSA, in millimeters) did not differ significantly according to degree of stenosis (Spearman rank test; r = 0.18, P = 0.26). Intravenous flat-detector CT can be a feasible and time-saving test for evaluating high-grade carotid stenosis and stenosis length.

Hybrid scatter correction for CT imaging

The purpose of this study was to develop and evaluate the hybrid scatter correction algorithm (HSC) for CT imaging. Therefore, two established ways to perform scatter correction, i.e. physical scatter correction based on Monte Carlo simulations and a convolution-based scatter correction algorithm, were combined in order to perform an object-dependent, fast and accurate scatter correction. Based on a reconstructed CT volume, patient-specific scatter intensity is estimated by a coarse Monte Carlo simulation that uses a reduced amount of simulated photons in order to reduce the simulation time. To further speed up the Monte Carlo scatter estimation, scatter intensities are simulated only for a fraction of all projections. In a second step, the high noise estimate of the scatter intensity is used to calibrate the open parameters in a convolution-based algorithm which is then used to correct measured intensities for scatter. Furthermore, the scatter-corrected intensities are used in order to reconstruct a scatter-corrected CT volume data set. To evaluate the scatter reduction potential of HSC, we conducted simulations in a clinical CT geometry and measurements with a flat detector CT system. In the simulation study, HSC-corrected images were compared to scatter-free reference images. For the measurements, no scatter-free reference image was available. Therefore, we used an image corrected with a low-noise Monte Carlo simulation as a reference. The results show that the HSC can significantly reduce scatter artifacts. Compared to the reference images, the error due to scatter artifacts decreased from 100% for uncorrected images to a value below 20% for HSC-corrected images for both the clinical (simulated data) and the flat detector CT geometry (measurement). Compared to a low-noise Monte Carlo simulation, with the HSC the number of photon histories can be reduced by about a factor of 100 per projection without losing correction accuracy. Furthermore, it was sufficient to calibrate the parameters in the convolution model at an angular increment of about 20°. The reduction of the simulated photon histories together with the reduced amount of simulated Monte Carlo scatter projections decreased the total runtime of the scatter correction by about two orders of magnitude for the cases investigated here when using the HSC instead of a low-noise Monte Carlo simulation for scatter correction.

Fast on‐site Monte Carlo tool for dose calculations in CT applications

Monte Carlo (MC) simulation is an established technique for dose calculation in diagnostic radiology. The major drawback is its high computational demand, which limits the possibility of usage in real-time applications. The aim of this study was to develop fast on-site computed tomography (CT) specific MC dose calculations by using a graphics processing unit (GPU) cluster. GPUs are powerful systems which are especially suited to problems that can be expressed as data-parallel computations. In MC simulations, each photon track is independent of the others; each launched photon can be mapped to one thread on the GPU, thousands of threads are executed in parallel in order to achieve high performance. For further acceleration, the authors considered multiple GPUs. The total computation was divided into different parts which can be calculated in parallel on multiple devices. The GPU cluster is an MC calculation server which is connected to the CT scanner and computes 3D dose distributions on-site immediately after image reconstruction. To estimate the performance gain, the authors benchmarked dose calculation times on a 2.6 GHz Intel Xeon 5430 Quad core workstation equipped with two NVIDIA GeForce GTX 285 cards. The on-site calculation concept was demonstrated for clinical and preclinical datasets on CT scanners (multislice CT, flat-detector CT, and micro-CT) with varying geometry, spectra, and filtration. To validate the GPU-based MC algorithm, the authors measured dose values on a 64-slice CT system using calibrated ionization chambers and thermoluminesence dosimeters (TLDs) which were placed inside standard cylindrical polymethyl methacrylate (PMMA) phantoms. The dose values and profiles obtained by GPU-based MC simulations were in the expected good agreement with computed tomography dose index (CTDI) measurements and reference TLD profiles with differences being less than 5%. For 10(9) photon histories simulated in a 256 × 256 × 12 voxel thorax dataset with voxel size of 1.36 × 1.36 × 3.00 mm(3), calculation times of about 70 and 24 min were necessary with single-core and multiple-core central processing unit (CPU) solutions, respectively. Using GPUs, the same MC calculations were performed in 1.27 min (single card) and 0.65 min (two cards) without a loss in quality. Simulations were thus speeded up by factors up to 55 and 36 compared to single-core and multiple-core CPU, respectively. The performance scaled nearly linearly with the number of GPUs. Tests confirmed that the proposed GPU-based MC tool can be easily adapted to different types of CT scanners and used as service providers for fast on-site dose calculations. The Monte Carlo software package provides fast on-site calculation of 3D dose distributions in the CT suite which makes it a practical tool for any type of CT-specific application.

Evaluation of stent visibility by flat panel detector CT in patients treated for intracranial aneurysms

This study aimed to evaluate the visibility of stents using high-resolution computed tomography (CT) acquisitions acquired with flat panel detector (XperCT, Allura series, Philips Healthcare, The Netherlands) for endovascular treatment of intracranial aneurysms. On a 24-month period, 48 patients endovascularly treated by coiling and stenting (59 stents) for intracranial aneurysms were explored by flat panel detector CT technique. A sequence of 620 2D images was acquired over an angle of 240° using a 1,024 × 1,024 pixel matrix detector within a 48-cm field of view. The images were retrospectively analyzed independently by two neuroradiologists. Evaluation criteria were percentage of visualization of the stents and stent deployment (kinking or unsatisfactory deployment of the stent). Evaluation of the stent was feasible for all the patients. Stent visibility by XperCT was overall estimated at 76% of the stent length. Difficulties to analyze the stents were related to coil artifacts but not to packing density or aneurysm location. Stent length visualization was higher when the acquisition was performed before additional coiling (P < 0.0001). Mild kinking/misdeployment was noticed in 22% of the cases. XperCT technique provides multiplanar and 3D reconstructions that allows for a satisfying visualization of intracranial stents. This CT-like acquisition should be performed after the stent deployment and before coiling, in order to obtain better stent visualization.

Cone Beam Computed Tomography in the Neurointerventional Room: Beyond Vessels

I f p fl t i t s g u b d C a I nitial attempts to create an interventional hybrid system capable of soft tissue rendering started with the application of computed tomography (CT) reconstruction algorithms to mage-intensifier angiography systems (6–8), but performance as poor until the introduction of flat panel detectors. Flat panel ensors consist of a layer of cesium iodide crystals over silicon hotodiodes (7); when equipped on C-arm rotational traditional ngiography gantries, these flat panel sensors could offer soft issue imaging capabilities to flat detector digital subtraction ngiography (DSA) suites. These hybrid systems have been eferred to in the literature as flat detector CT (FDCT) (6), C-arm at detector CT (7), cone beam CT (16), and C-arm cone beam CT 11). The hybrid systems can provide the operator with direct ntraprocedural and postprocedural feedback, with the potential o guide or alter operational and clinical decisions.