Film-forming Solutions Research Articles

Emulsion-based edible chitosan film containing propolis extract to extend the shelf life of strawberries

In this study, propolis was first loaded into a conventional oil-in-water emulsion, which was combined with a chitosan film-forming solution to produce propolis emulsion-loaded film (PEF). Strawberries inoculated with Botrytis cinerea coated with PEF and blank emulsion-loaded films (BEF) were stored for 14 days at 4 °C. Compared to BEF, PEF showed superior mechanical and oxygen barrier properties, as well as antioxidant activities, but higher moisture permeability. PEF showed less oil agglomeration on the film surface after drying, as demonstrated by scanning electron microscopy (SEM) analysis. Compared to uncoated strawberries, coatings did not have a significant effect on weight loss or firmness during storage. In contrast, coated strawberries showed elevated total phenolics, anthocyanins, and ascorbic acid retention; however, PEF-coating yielded higher values. Moreover, the PEF coating resulted in a significantly lower reduction of organic acid and total soluble solids. Mold growth was visible in both uncoated and BEF-coated strawberries after 7 days of storage, while PEF-coated fruits showed no visible mold until the end of storage. Starting from day 4, PEF-coated fruits showed lower mold counts (~2 log CFU/g) than other samples. Therefore, the PEF prepared in this study has application potential for the preservation of fresh fruits.

Utilization of Spent Coffee Grounds as a Food By-Product to Produce Edible Films Based on κ-Carrageenan with Biodegradable and Active Properties.

Coffee ranks as the second most consumed beverage globally, and its popularity is associated with the growing accumulation of spent coffee grounds (SCG), a by-product that, if not managed properly, constitutes a serious ecological problem. Analyses of SCG have repeatedly shown that they are a source of substances with antioxidant and antimicrobial properties. In this study, we assessed SCG as a substrate for the production of edible/biodegradable films. The κ-carrageenan was utilized as a base polymer and the emulsified SCG oil as a filler. The oil pressed from a blend of Robusta and Arabica coffee had the best quality and the highest antioxidant properties; therefore, it was used for film production. The film-forming solution was prepared by dissolving κ-carrageenan in distilled water at 50 °C, adding the emulsified SCG oil, and homogenizing. This solution was cast onto Petri dishes and dried at room temperature. Chemical characterization showed that SCG increased the level of polyphenols in the films and the antioxidant properties, according to the CUPRAC assay (CC1 23.90 ± 1.23 µmol/g). SCG performed as a good plasticizer for κ-carrageenan and enhanced the elongation at the break of the films, compared with the control samples. The solubility of all SCG films reached 100%, indicating their biodegradability and edibility. Our results support the application of SCG as an active and easily accessible compound for the food packaging industry.

Pectin/sodium alginate-based active film integrated with microcrystalline cellulose and geraniol for food packaging applications

Biopolymer-based packaging films were prepared from pectin (PEC) and sodium alginate (SA), with the incorporation of 10 % MCC and different concentrations of geraniol (GER at 2.5, 5.0, 7.5, and 10.0 %). Rheological properties suggested that film-forming solutions and film-forming emulsions exhibited a shear-thinning or pseudo-plastic non-Newtonian behaviour. The dried films were crosslinked with 2.0 % CaCl2. The addition of MCC into PEC/SA film enhanced the TS but reduced it with the impregnation of GER without influencing the EAB and toughness of the film. The water solubility of the films significantly reduced with the rise in the GER levels but enhanced the water vapor and oxygen barrier attributes. TGA demonstrated that incorporating MCC reduced the film's thermal degradation (44.92 % to 28.81 %), but GER had an insignificant influence on the thermal stability. FTIR spectra revealed that hydrogen bond formation was positively linked with the GER addition in the film formulation. X-ray diffractograms showed that prepared films were predominantly amorphous. Antimicrobial studies showed a complete reduction of Escherichia coli and Bacillus cereus in 24 h. Overall, the composite film displayed excellent physical and active properties and PEC/SA/MCC/5.0 %GER/CaCl2 film was considered the best formulation for food packaging applications.

Ultrasonication-based preparation of raw chitin nanofiber and evaluation of its reinforcement effect on chitosan film for functionalization with curcumin

Raw chitin nanofibers (CNF) through an 8-min high-power sonication process were successfully prepared. Well-preserved nanofibers with diameters of 50–100 nm and lengths of 3–10 μm were observed by atomic force microscopy. The high aspect ratio induced strong entanglement under high shear rates, leading to a typical nanofiber four-region shear-thinning behavior. These native chitin nanofibers were incorporated into chitosan film-forming solutions at different concentrations. FTIR results indicated intermolecular hydrogen bonds between CS and CNF. Tensile strength was significantly enhanced with the inclusion of CNF, with the highest stress at 30% CNF incorporation. Elongation at break increased up to 35% with 10% CNF concentration, gradually decreasing with higher CNF content. CS with 20% addition of CNF content was chosen for curcumin addition considering the high mechanical performance and low grammage value. Oxygen transmission rate reduced slowly with increasing CNF concentration, and a significant drop by about 90% was observed upon curcumin inclusion. UV blocking performance and antioxidant ability were drastically improved after curcumin inclusion. The utilization of raw CNF as a film reinforcement nanofiller offers several advantages, including ease of preparation, higher aspect ratio, longer length, and superior mechanical performance. CNF-reinforced chitosan films emerge as potent candidates for functional food packaging materials.

Bio-based composite active film/coating from deccan hemp seed protein, taro starch and leaf extract: Characterizations and application in grapes

This study aimed to create a novel, cost-effective, and environmentally friendly food packaging film or coating using agricultural waste materials such as deccan hemp seeds and leaves. The process involved blending deccan hemp seed protein and leaf extract at an optimal ratio through a casting technique. Additionally, starch isolated from taro root was added into the protein-based film to enhance its structural, barrier, and mechanical properties. The introduction of bioactive compounds, like deccan hemp leaf extract, led to increase in antioxidant activity and enriching the film with beneficial phenolic compounds.The combination of leaf extract and starch with the protein film resulted in a homogeneous, dense, and smooth film matrix, as evidenced by scanning microscopy images. FTIR spectroscopy confirmed interlinkage among the various constituents in the film. Rheological analysis of the film-forming solution showed its shear-thinning behavior, with the storage modulus exceeding the loss modulus in the angular frequency range of 0.1 rad/s to 100 rad/s, indicating the film's elastic nature. Furthermore, the physical and optical attributes of the films were enhanced through the addition of starch and leaf extract.In a practical application, the film-forming solution was applied to grapes, leading to improved quality and extended shelf life for grapes stored under ambient conditions for ten days. Overall, this study's findings suggest that the use of deccan hemp seed protein-based packaging film holds promise as an emerging solution for enhancing the shelf life of vegetables and fruits, offering a sustainable and effective alternative for food packaging.

Konjac glucomannan-based highly antibacterial active films loaded with thyme essential oil through bacterial cellulose nanofibers/Ag nanoparticles stabilized Pickering emulsions

The aim of this study was to develop novel konjac glucomannan (KGM)-based highly antibacterial active films, where five types of films were prepared and compared. The microstructure results showed that KGM-based films loaded with thyme essential oil (TEO) through bacterial cellulose nanofibers/Ag nanoparticles (BCNs/Ag nanoparticles) stabilized Pickering emulsions (Type V films) displayed the smoothest surface and the most evenly dispersed TEO droplets as compared with the other four types of films. Moreover, Type V films showed the highest contact angle value (86.28°), the best thermal stability and mechanical properties. Furthermore, Type V films presented the highest total phenol content (13.23 mg gallic acid equivalent/g film) and the best antioxidant activity (33.96 %) as well as the best sustained-release property, thus showing the best antibacterial activity, which was probably due to that BCNs/Ag nanoparticles and TEO displayed a synergistic effect to some extent. Consequently, Type V film-forming solutions were used as coatings for tangerines. The results showed that the tangerines treated with Type V coatings displayed excellent fresh-keeping properties. Therefore, the coatings, KGM-based film-forming solutions loaded with TEO through BCNs/Ag nanoparticles stabilized Pickering emulsions, have great potential for the preservation of fruits and vegetables.

Carvacrol and thymol effect in vapor phase on Escherichia coli and Salmonella serovar Typhimurium growth inoculated in a fresh salad

This study aimed to evaluate the antimicrobial effect of thymol and carvacrol in inhibiting Escherichia coli and Salmonella serovar Typhimurium inoculated on a fresh green salad through the vapor phase. A film-forming solution was prepared by dissolving starch, sorbitol, and variying concentrations of carvacrol, thymol, and a mixture of both. The film-forming solution containing the respective antimicrobial agent was then added lid, which was sealed rigidly and hermetically to achieve different concentrations (105 mg/L of air of carvacrol, 105 mg/L of air of thymol, and a mixture of 52 mg/L of air of carvacrol and 52 mg/L of air of thymol). Each active package contained fresh green salad inoculated with E. coli or Salmonella serovar Typhimurium. The active packages were then sealed and refrigerated at a temperature of 6 °C for 48 h. Growth/inhibition curves were modelled using the Weibull equation, and consumer acceptance was evaluated. Carvacrol can reduce up to 0.5 log-cycles, while thymol can reach almost 1 log cycle. Blending the components with half the concentration has a synergistic effect, inhibiting up to 2.5 log cycles. Consumer ratings revealed no significant differences between the packages. However, the average score was 5.4 on a 9-point hedonic scale, evaluators' comments did not indicate dislike or a strong taste characteristic of thymol and carvacrol.

Edible film preparation by anthocyanin extract addition into acetylated cassava starch/sodium carboxymethyl cellulose matrix for oxidation inhibition of pumpkin seeds

In this study, an edible film was fabricated by incorporating anthocyanin extract from black rice (AEBR) into acetylated cassava starch (ACS)/carboxymethyl-cellulose (CMC) to enhance the shelf life of pumpkin seeds. The effects of AEBR on the rheological properties of film-forming solutions, as well as the structural characterization and physicochemical properties of the film, were evaluated. Rheological properties of solutions revealed that AEBR was evenly dispersed into polymer matrix and bound by hydrogen bonds, as confirmed by Fourier transform infrared spectroscopy analysis. The appropriate AEBR addition could be compatible with polymer matrix and formed a compact film structure, improving the mechanical properties, barrier properties, and opacity. However, with further addition of AEBR, the tensile strength and water vapor permeability decreased and the tight structure was destroyed. After being stored separately under thermal and UV light accelerated conditions for 20 days, the peroxide value and acid value of roasted pumpkin seeds coated with the AEBR film showed a significant reduction. Moreover, the storage stability of AEBR was improved through the embedding of ACS/CMC biopolymers. These results indicated that AEBR film could effectively delay pumpkin seeds oxidation and prolong their shelf life as an antioxidant material.

Применение комплекса биологически активных веществ из Аronia melanocarpa в парафармацевтических фитоплёнках

The article presents the results of using non-pharmacopoeial plant raw material – dried leaves of the perennial cultivated chokeberry shrub Aronia melanocarpa (Michx.) Elliott. as a source of substances with anti-inflammatory and wound-healing effect. The development of a parapharmaceutical phytofilm based on a complex of biologically active substances from A. melanocarpa is described. The results of preclinical evaluation of the developed phytofilm in an experimental model of skin wound on outbred white rats are presented. The developed phytofilm is environmentally safe compared to synthetic analogues which production is accompanied by a negative environmental impact. Substances with antioxidant properties which can play the role of a medicinal base were found in the composition of aqueous extracts from chokeberry leaves: polyphenols – 7.4±0.7, tannins – 4.6±0.5 mg/cm3. The safety of using A. melanocarpa leaves as raw material for phytofilm has been confirmed in heavy metal tests. The composition and film-forming ability of chokeberry leaves aqueous extract, including polyvinyl alcohol (098-15(G)) (6%), food grade gelatin P-11 (0.5%), glycerin (GOST 6259-75) (0.4%), colloidal silver solution 200 mg/dm3 (1%) has been established. A. melanocarpa leaves extract application to the film-forming solution increases the final vapor permeability by 48% and solubility by 14%. The model experiment shows the effect of using the created phytofilm in the reparation of linear wounds, manifested as significant decrease in their length by 30% by the fifth day, by 25% by the seventh day compared with the control, as well as normalization of the skin histological structure by the tenth day.

Regulation of fine structure of different types of natural waxes by octenyl succinate starch in starch bioplastics

This work conducted a comparative study on the ability of octenyl succinate starch to regulate the fine structure and physicochemical properties of starch-based plastics containing different types (beeswax, candelilla wax, carnauba wax) and contents of waxes. All the waxes increased the apparent viscosity and storage modulus of the film-forming solution, and obstructed the establishment of hydrogen bond within the film matrix. The limited emulsifying capacity of octenyl succinate starch resulted in different distributions of the three waxes in the matrices, thereby forming different films' microstructures. Carnauba wax negatively affected the hydrophobicity, barrier and mechanical properties of the films due to its poor compatibility with the starches. In contrast, the addition of beeswax and candelilla wax effectively improved the hydrophobicity and moisture barrier, especially for some appropriate wax heterostructures presented in the matrices. Results suggested that octenyl succinate starch could be well emulsified and compatible with beeswax (5%–15% w/w content) to regulate the fine structure to achieve lower water sensibility of starch bioplastics.

Gellan gum-based nanocomposites films containing bio-reduced silver nanoparticles: Synthesis, characterisation and antifungal activity

The aim of this work was to develop and characterise nanocomposite thin films containing silver nanoparticles (AgNPs), as wound dressings and antifungal materials, using a green process for the nanoparticles’ synthesis and a single step procedure for the preparation of the nanocomposite films. To this end, polyphenol-rich extracts obtained from kiwi peels, an agri-food industrial by-product, were used as a reducing agent of silver nitrate salt. The AgNPs were let form within the film-forming solution, which was composed by low acyl gellan gum and a plasticising agent (glycerol or PEG 400 g/mol) and the corresponding nanocomposite films were deposited by the solvent casting technique. The plasticising agent affected the AgNPs distribution within the films, as observed by SEM and EDS analyses, and consequently their tensile behaviour. In specific, AgNPs act as stress intensifiers in the presence of glycerol, whereas they act as film reinforcement with PEG400. However, both glycerol-plasticised and PEG400-plasticised films exhibited similar antifungal efficacy against 16 clinical isolates of 5 different Candida spp (C. albicans, C. lusitaniae, C. haemulonii, C. krusei and C. glabrata). Globally, the present study provides a green and single-step procedure to develop nanocomposite films embedding AgNPs obtained by in situ reduction of silver ions with polyphenol-rich extracts.

Gelatine-Based Biopolymer Film Produced from Ozone-Treated Film-Forming Solutions Containing Whey Protein Concentrate: Effects on Physical, Mechanical, and Thermal Characteristics

This study aimed to determine the effects of the ozone treatment of film-forming solutions (FFSs) containing whey protein concentrate (WPC) and gelatine on biopolymer films’ physical, mechanical, and thermal properties. Film samples were produced from a FFS that was ozone-treated at 0 (control), 5, 10, and 30 min. Ozone treatment caused an increase in the pH values of the FFS, whereas the zeta potential remained negative. The films became lighter in colour, slightly greenish, and more opaque with longer ozonation times. The control sample showed the highest thermogravimetric weight loss (92.15%). The weight loss of the samples decreased with increasing ozone treatment time. The application of ozone treatment on the FFS enhanced the films’ mechanical properties. Increased ozone treatment time improved the film samples’ tensile strength, elongation at break, and toughness values. In conclusion, the results of this study demonstrate that the ozone treatment of FFS containing whey protein concentrate and gelatine can significantly enhance the physical, mechanical, and thermal properties of biopolymer films. These results highlight the potential of ozone treatment as a viable method for improving the performance and quality of biopolymer films used in food packaging, offering promising advantages for sustainable and environmentally friendly packaging solutions.

Physicochemical and antimicrobial properties of soy protein isolate films incorporating high internal phase emulsion loaded with thymol

Oil-in-water (O/W) high internal phase (HIP) emulsion was prepared to investigate its effects on the physicochemical properties and antimicrobial properties of soy protein isolate (SPI)-based films. The particle size and migration degree of oil droplets in the SPI film-forming solution with HIP emulsion and the films were lower than those with conventional O/W emulsion or oil. The SPI-based emulsion films with HIP emulsion containing 30 % oil had the lowest water vapor permeability (1.15 × 10−10 g·m−1·s−1·Pa−1), glass transition temperature (40.93 °C) and tensile strength (4.47 MPa), and the highest transparency value (12.87) and elongation at break (160.83 %). The antimicrobial test of the SPI-based emulsion films loaded with thymol showed that the thymol encapsulation efficiency, sustained release effect, and growth inhibition effect on microbes were higher for the films with HIP emulsion than those for the films with O/W emulsion or oil.

Fabrication and in vitro characterization of curcumin film-forming topical spray: An integrated approach for enhanced patient comfortandefficacy.

Curcumin, known for its anti-inflammatory properties, was selected for the developing consumer friendly film forming spray that offers precise delivery of curcumin and and improves patient adherence. An optimized film-forming solution was prepared by dissolving curcumin (1%), Eudragit RLPO (5%), propylene glycol (1%), and camphor (0.5%) in ethanol: acetone (20:80) as the solvent. The solution was filled in a spray container which contained 70% solutions and 30% petroleum gas. In-vitro characterization was performed. Potential anti-inflammatory phytoconstituents were extracted from the PubChem database and prepared as ligands, along with receptor molecules (nsp10-nsp16), for molecular docking using Autodock Vina. The docking study showed the lowest binding energy of -8.2 kcal/mol indicates better binding affinities. The optimized formulation consisted of ethanol:acetone (20:80) as the solvent, Eudragit RLPO (5%) as the polymer, propylene glycol (1%) as the plasticizer, and camphor oil (0.5%) as the penetration enhancer. The optimized formulation exhibited pH of 5.8 ± 0.01, low viscosity, low film formation time (19.54 ± 0.78 sec), high drug content (8.243 ± 0.43 mg/mL), and extended ex vivo drug permeation (85.08 ± 0.09%) for nine hours. Consequently, the formulation was incorporated into a container using 30% liquefied petroleum gas, delivering 0.293 ± 0.08 mL per actuation, containing 1.53 ± 0.07 mg of the drug. The film-forming spray exhibited higher cumulative drug permeation (83.94 ± 0.34%) than the marketed cream formulation and pure drug solution after 9 h, with an enhancement ratio of 14. Notably, the film-forming spray exhibited no skin irritation and remained stable for over three months. The developed curcumin film-forming system is promising as a carrier for wound management because of its convenient administration and transport attributes. Further in vivo studies are required to validate its efficacy in wound management.

New blend of renewable bioplastic based on starch and acetylated xylan with high resistance to oil and water vapor

Renewable materials of biological origin exhibit attractive properties in relation to traditional plastics, as they can be partially or completely replaced, thereby reducing environmental impacts. Hemicelluloses are a group of polysaccharides that have expanded applications when acetylated. Acetylation can improve the mechanical strength and water vapor barrier properties of xylan-based bioplastics. By partially acetylating xylan in the present study, it was possible to use water as a solvent for the film-forming solution and starch as a second polysaccharide in the formation of bioplastics. Xylan was modified via partial chemical acetylation by varying the reaction time, solvent, and catalyst content. The bioplastics were formed by non-acetylated xylan and acetylated xylan with degrees of substitution (DS) of 0.45 and 0.9, respectively, with starch to form blends using glycerol as a plasticizer. Acetylation with DS 0.45 showed better results in increasing the hydrophilicity of the bioplastic. On the other hand, acetylation influenced the thermal stability of bioplastics, increasing the maximum temperature of the degradation rate from 302 °C to 329 °C and 315 °C, owing to changes in the crystallinity of the polymers. In addition to the modulus of elasticity 2.99 to 290.61 and 274.67 MPa for the non-acetylated bioplastic and the bioplastic with DS of 0.45 and 0.90, respectively. Thus, the films obtained presented suitable physicochemical properties for use in various industrial applications, such as active and intelligent packaging in the food sector.

Investigation of the Structure-Forming Potential of Protein Components in the Reformulation of the Composition of Edible Films.

To optimize the functional properties of edible films or coatings, mixtures of several ingredients are used, including food processing by-products. In this way, pectin from fruit pomace, whey proteins from whey as a by-product of rennet cheese production, and gelatin from by-products of the processing of slaughtered animals can be obtained. The aim and scope of the investigation were to verify the hypothesis of the research, which assumes that the addition of beef broth to edible gelatin films will affect the gelation processes of the tested film-forming solutions and will allow for the modification of the edible properties of the films obtained based on these solutions. Measurements were carried out to determine the visual parameters, mechanical strengths, surface and cross-sectional structures, FTIR spectra, thermal degradation rates, and hydrophilicities of the prepared gelatin films. The water content, water vapor permeability, and course of water vapor sorption isotherms of the films were also examined, as well as the course of the gelation process for film-forming solutions. The addition of broth to film-forming solutions was found to increase their opacity and color saturation, especially for the ones that were yellow. The films with the addition of broth were more uneven on the surface and more resistant to stretching, and in the case of the selected types of gelatins, they also formed a more stable gel. The broth increased the hydrophilicity and permeability of the water vapor and reduced the water content of the films. The addition of broth enables the practical use of edible films, but it is necessary to modify some features.

Film-forming polymer solutions containing cholesterol myristate and berberine mediate pressure ulcer repair via the Wnt/β-catenin pathway.

Pressure ulcer (PU) is a worldwide problem that is difficult to address because of the related inflammatory response, local hypoxia, and repeated ischaemia/reperfusion, causing great suffering and financial burden to patients. Traditional Chinese medicine turtle plate powder can treat skin trauma, but its composition is complex and inconvenient to use. Here, we combined cholesterol myristate (S8) with berberine (BBR), with anti-inflammatory and antibacterial effects, as a drug and used hydroxypropyl methylcellulose and polyvinylpyrrolidone K30 as carriers to construct a novel film-forming polymeric solution (S8 + BBR FFPS), comprehensively study its reparative effect on PU and explore the potential mechanism in rat PU models. The results showed that S8 + BBR FFPS inhibits excessive inflammatory response, promotes re-epithelialization, and promotes hair follicle growth during the healing process of PU, which may be related to the activation of the Wnt/β-catenin signalling pathway by S8 + BBR FFPS to mediate hair follicle stem cell proliferation and maintain skin homeostasis. Therefore, S8 + BBR FFPS may be a potential candidate for the treatment of chronic skin injury, and its association with the Wnt/β-catenin signalling pathway may provide new ideas to guide the design of biomaterial-based wound dressings for chronic wound repair.

Characterization of Polyvinyl Alcohol (PVA)/Polyacrylic Acid (PAA) Composite Film-Forming Solutions and Resulting Films as Affected by Beeswax Content.

Recently, the food packaging industry has focused on developing an eco-friendly and sustainable food packaging system. This study describes the effect of beeswax on the physical, structural, and barrier properties of a polyvinyl alcohol (PVA)/polyacrylic acid (PAA) composite film. The incorporation of beeswax improved the barrier properties against oxygen, water, and oil. However, the addition of a high content of beeswax caused phase separation in the film-forming solution. The destabilization mechanisms such as clarification and creaming formation in the film-forming solution were revealed by turbidimetric analysis. The results of scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) indicates that non-homogeneous structures in the film-forming solution were formed as a function of increased beeswax content due to the agglomeration of beeswax. The mechanical properties of the films were also evaluated to determine the most appropriate content of beeswax. There was a slight decrease in tensile strength and an increase in elongation as beeswax content increased up to 10%. Thus, the PVA/PAA composite film with 10% beeswax was chosen for further applications. In summary, the PVA/PAA composite film developed in this study with 10% beeswax exhibited a significant improvement in barrier properties and has the potential for use in commerce.

Sustained-release film prepared by incorporation of cinnamon essential oil: Physicochemical properties and application in the preservation of mushroom (Agaricus bisporus)

The chitosan/zein/cinnamon essential oil (CEO) sustained-release active film was developed. The rheological properties of film-forming solutions (FFS) and the physicochemical properties of films were investigated. The effects of active film on mushroom quality were evaluated. When CEO and Tween 80 were mixed in a ratio of 1:3, the particle size of the essential oil emulsion was the smallest and the distribution was more uniform. Rheological analysis showed that FFS was non-Newtonian fluids. With the increase of CEO, FFS became more viscous and the intermolecular entanglement was enhanced. CEO improved the UV-blocking activity and hydrophobicity of the composite film. The tensile strength increased from 16.54 to 21.22 MPa. Moreover, the active film inhibited the growth of Pseudomonas tolaasii. And the antioxidant property of film was improved with the addition of CEO. The SEM images, FTIR, and XRD spectra displayed that CEO had good compatibility with film matrix. TGA demonstrated the thermal stability of film was enhanced. In addition, the release of CEO in four simulants followed Fick's law of molecular diffusion. Compared with the control group and C/Z group, the L* value of mushrooms treated with C/Z-CEO0.6% films could be kept above 80 during storage, and the spoilage index of mushrooms was lower (31.2%). Mushroom treated with C/Z-CEO0.6% films showed the lowest weight loss and the highest firmness. All in all, the chitosan/zein-based active films containing CEO, as a new food packaging ma restrainterial, will play a good role in retaining the quality of food.

Incorporation of cellulose nanocrystals to improve the physicochemical and bioactive properties of pectin-konjac glucomannan composite films containing clove essential oil

This study aimed to investigate the effectiveness of cellulose nanocrystals (CNC) isolated from cotton in augmenting pectin (PEC)/konjac glucomannan (KGM) composite films containing clove essential oil (CEO) for food packaging application. The effects of CNC dosage on film properties were examined by analyzing the rheology of film-forming solutions and the mechanical, barrier, antimicrobial, and CEO-release properties of the films. Rheological and FTIR analysis revealed the enhanced interactions among the film components after CNC incorporation due to its high aspect ratio and abundant hydroxyl groups, which can also prevent CEO droplet aggregation, contributing to form a compact microstructure as confirmed by SEM and 3D surface topography observations. Consequently, the addition of CNC reinforced the polysaccharide matrix, increasing the tensile strength of the films and improving their barrier properties to water vapor. More importantly, antibacterial, controlled release and kinetic simulation experiments proved that the addition of CNC could further slow down the release rate of CEO, prolonging the antimicrobial properties of the films. PEC/KGM/CEO composite films with 15 wt% CNC was found to have relatively best comprehensive properties, which was also most effective in delaying deterioration of grape quality during the storage of 9 days at 25 °C.