Field Distortion Research Articles

Silane modified Cr2O3/polyimide nanocomposite films with excellent surface insulation performance for space applications

The exploration of deep space significantly increases the probability of spacecraft failures due to surface electrostatic discharge, which imposes higher vacuum insulation protection requirements on polyimide (PI), the external insulation material of spacecrafts. To address this challenge, this study proposes using silane coupling agent KH550 for organic grafting treatment of Cr2O3nanoparticles, which are then used to dope and modify PI to enhance the vacuum surface insulation of PI films. The KH550 grafting improves the interface strength between the fillers and the matrix, allowing the fillers to be uniformly dispersed in the matrix. Compared to pure PI films, the prepared PI-Cr2O3@KH550 composite films exhibit significantly enhanced vacuum surface flashover voltage, improved surface/volume resistivity, and dielectric properties. The results demonstrate that PI composite films with 0.8% by mass of Cr2O3@KH550 show the most notable performance improvement, with the DC flashover voltage and impulse flashover voltage in vacuum increasing by 20.7% and 27.8%, respectively. The doping of chromium oxide nanoparticles introduces more deep traps into the PI films and reduce the surface resistivity. The higher deep trap density inhibits charge migration, thereby alleviating secondary electron emission and surface electric field distortion. Simultaneously, the lower surface resistivity facilitates dissipating surface charges and improves the surface insulation. These findings are of significant reference value for promoting the enhancement of aerospace insulation performance.

Study on the Influence of Volute Throat Jet on Excitation Vibration Alleviation of Radial Turbine Blade

Abstract Turbine blade fracture, resulting from high-cycle fatigue (HCF), is the most commonly observed failure mode of turbochargers. In a vaneless turbine, the radial turbine blade is susceptible to HCF under excessive aerodynamic excitation due to the flow field distortion caused by the volute tongue. The present study explores a technique to mitigate blade excitation by reducing pressure disturbance in the volute tongue area. The gas with higher pressure in the inlet section of the volute is transferred to the low-static pressure area upstream of the volute tongue through a throat jet hole. The usage of high-pressure gas improved the homogeneity of the flow field near the volute tongue. The study investigates the mitigation of high-pressure gas jet on turbine blade excitation, the impact of jet hole geometry on the suppression effect of the blade vibration, and the effect of high-pressure jet on turbine performance using numerical simulation of unsteady flow fields. The results indicate that the jet flow has a substantial impact on dampening the blade vibrations. The harmonic pressure amplitude at the monitor point located within the high blade vibration amplitude region is reduced by up to 56%. Generalized pressure analysis reveals that the aerodynamic excitation of the turbine blades is significantly reduced. Experimental evidence verifies the effectiveness of the jet hole scheme in reducing blade vibration. Moreover, the jet hole has a negligible effect on turbine efficiency. However, there is a degree of increased stress in the volute tongue with a jet hole which needs to be evaluated in engineering applications.

SF6 Experimental Study on the Variation Characteristics of Closing Prebreakdown Duration during Contact Deterioration of Circuit Breakers

The contact morphology change caused by high-current ablation will seriously affect the electric field distribution in the interrupter chamber, which in turn affects the closing prebreakdown arc duration, indicating that the prebreakdown arc duration can be used as one of the indicators to measure the contact ablation state. A circuit breaker simulated ablation test platform was established, and the voltage and current signals, electromagnetic field signals, and vibration signals in the process of circuit breaker closing were measured, and the closing prebreakdown duration was calculated. The results show that under the same size of the ablation current, with the ablation of the contacts, the closing prebreakdown duration shows an overall trend of increasing and then decreasing, and the larger the ablation current is, the larger the change in the closing prebreakdown duration is. At the same time, simulation verification was carried out, and the results show that the electric field distortion on the surface of the static arc contact inside the arc extinguishing chamber is the largest, and the ablation of the contact will further increase the degree of distortion of the electric field inside the arc extinguishing chamber. As the degree of ablation increases, the prebreakdown moment of the circuit breaker closing is advanced, and the prebreakdown duration increases.

Exact and fractional solution of MHD generalized Couette hybrid nanofluid flow with Mittag–Leffler and power law kernel

This study investigates the complex behavior of Jeffrey nanofluid flow in a porous oscillating microchannel under the influence of magnetohydrodynamic (MHD) effects. The research explores how magnetic field distortions lead to diverse accumulation patterns of nanofluid particles, a phenomenon attributed to homogeneous magnetization in fluid dynamics. Nanoparticles ranging from 0.25 % to 0.5 % (low and inexpensive concentrations) are remarkably consistent for best results in most machining procedures. Different concentrations of various nanomaterial's is utilized (φ1 = φ2 = 0.01, 0.02, 0.03, 0.04) to make the simple nanfluid and hybrid nanofluid suspensions. By employing fractal-fractional derivatives governed by power law, a mathematical model developed to describe the time-varying, compressible MHD flow of Jeffrey nanofluid. The model incorporates the effects of heat transfer, pressure, and magnetic fields on the fluid dynamics. A novel fractional approach utilizing the Laplace transform is applied to solve the fractal MHD hybrid-fluid model integrated into a porous medium. The study reveals velocity flow decrease with increasing Reynolds numbers but increase with channel inclination. Additionally, both the Darcy number and magnetic field orientation enhance heat transfer rates. In addition, the velocity profile enhanced by the hybrid nanofluid suspension as compared to simple nanofluid flow. The research validates its findings by demonstrating the convergence of fractional and numerical solution methods. Furthermore, the study compares the performance of different hybrid nanofluids, concluding that water-based (H2O + GO + MoS2) hybrid fluids exhibit slightly superior characteristics compared to (CMC + GO + MoS2) hybrid nanofluids.

A Hierarchical Point-spread Function Reconstruction Method

Reconstruction of the point-spread function (PSF) plays an important role in many areas of astronomy, including photometry, astrometry, galaxy morphology, and shear measurement. The atmospheric and instrumental effects are the two main contributors to the PSF, both of which may exhibit complex spatial features. Current PSF reconstruction schemes typically rely on individual exposures, and their ability to reproduce the complicated features of the PSF distribution is therefore limited by the number of stars. Interestingly, in conventional methods, after stacking the model residuals of the PSF ellipticities and (relative) sizes from a large number of exposures, one can often observe some stable and nontrivial spatial patterns on the entire focal plane, which could be quite detrimental to, e.g., weak-lensing measurements. These PSF residual patterns are caused by instrumental effects, as they consistently appear in different exposures. Taking this as an advantage, we propose a multilayer PSF reconstruction method to remove such PSF residuals, the second and third layers of which make use of all available exposures together. We test our method on the i-band data of the second release of the Hyper Suprime-Cam. Our method successfully eliminates most of the PSF residuals. Using the Fourier_Quad shear measurement method, we further test the performance of the resulting PSF fields on shear recovery using the field distortion effect. The PSF residuals have strong correlations with the shear residuals, and our new multilayer PSF reconstruction method can remove most of such systematic errors related to the PSF, leading to much smaller shear biases.

JWST MIRI flight performance: Imaging

The Mid-Infrared Instrument (MIRI) aboard the James Webb Space Telescope (JWST) provides the observatory with a huge advance in mid-infrared imaging and spectroscopy covering the wavelength range of 5–28 µm. This paper describes the performance and characteristics of the MIRI imager as understood during observatory commissioning activities, and through its first year of science operations. We discuss the measurements and results of the imager’s point spread function, flux calibration, background, distortion and flat fields as well as results pertaining to best observing practices for MIRI imaging, and discuss known imaging artefacts that may be seen during or after data processing. Overall, we show that the MIRI imager has met or exceeded all its pre-flight requirements, and we expect it to make a significant contribution to mid-infrared science for the astronomy community for years to come.

Reproducible and highly miniaturized bazooka RF Balun using a printed capacitor.

There is currently a strong trend in developing RF coils that are high-density, lightweight, and highly flexible. In addition to the resonator structure of the RF coil itself, the balun or cable trap circuit serves as another essential element in the functionality and sensitivity of RF coils. This study explores the development and application of reproducible highly miniaturized baluns in RF coil design. We introduce a novel approach to producing Bazooka baluns with printed coaxial capacitors, enabling the achievement of significant capacitance per unit length. Rigorous electromagnetic simulations and thorough hardware fabrication validate the efficacy of the proposed design across various magnetic field strengths, including 1.5 T, 3 T, and 7 T MRI systems. Bench testing reveals that the proposed balun can achieve an acceptable common-mode rejection ratio even when it is highly miniaturized. The use of printed capacitors allows for a notable reduction in balun length and ensures high reproducibility. Findings demonstrate that the proposed balun exhibits no RF field distortion even when placed close to the sample, making it suitable for flexible coils, wearable coils, and high-density coils, particularly in high-field MRI. The reproducibility inherent in the manufacturing process of printed coaxial capacitors allows for simple fabrication and ensures consistency in production. These advancements pave the way for the development of flexible coils, wearable coils, and high-density coils.

Run-time motion and first-order shim control by expanded servo navigation.

To provide a navigator-based run-time motion and first-order field correction for three-dimensional human brain imaging with high precision, minimal calibration and acquisition, and fast processing. A complex-valued linear perturbation model with feedback control is extended to estimate and correct for gradient shim fields using orbital navigators (2.3 ms). Two approaches for sensitizing the model to gradient fields are presented, one based on finite differences with three additional navigators, and another projection-based approximation requiring no additional navigators. A mechanism for noise decorrelation of the matrix and the data is proposed and evaluated to reduce unwanted parameter biases. The rigid motion and first-order field control achieves robust motion and gradient shim corrections improving image quality in a series of phantom and in vivo experiments with varying field conditions. In phantom scans, magnet drifts, forced gradient field perturbations and field distortions from shifts of a second bottle phantom are successfully corrected. Field estimates of the magnet drifts are in good agreement with concurrent field probe measurements. For in vivo scans, the proposed method mitigates field variations from torso motions while being robust to head motion. In vivo gradient field precisions were along with single-digit micrometer and millidegree rigid precisions. The navigator-based method achieves accurate, high-precision run-time motion and field corrections with low sequence impact and calibration requirements.

Scalable In-situ Microfibrillar dielectric films: Achieving exceptional energy density and efficiency

It is a formidable challenge to develop a feasible strategy for the scalable fabrication of all-organic dielectrics with simultaneous improvements in both discharged energy density (Ud) and efficiency (η). Herein, an innovative technology of “melting extrusion-hot stretching-quenching” was put forward for the large-scale preparation of all-organic polymer dielectric films, where polymethyl methacrylate (PMMA) was miscible with polyvinylidene fluoride (PVDF) to form single dispersed phase in the polypropylene (PP) matrix and in-situ transformed into microfibrils with the aid of elongational flow field. Thereby, a simultaneous enhancement in the dielectric constant and breakdown strength was achieved and the as-prepared PP-based all-polymer dielectric film exhibited an unprecedented ultrahigh Ud of 9.6 J cm−3 and an exceptional η of 90.9 %. Experimental verification and computational simulation confirmed that the formation of highly oriented PMMA/PVDF microfibrils and well-aligned interfaces are constructive to enhancing breakdown strength by suppressing electric field distortion. The highly oriented dipoles in PVDF and PMMA, coupled with the eliminated ferroelectric behavior of PVDF, synergistically contributed to the heightened Ud and η. The approach presented in this work opens up a promising avenue for the large-scale production of all-organic capacitor films with enhanced Ud and η, heralding a new era of advanced dielectric materials.

Study on the Relationship between Electron Transfer and Electrical Properties of XLPE/Modification SR under Polarity Reversal.

The insulation of high-voltage direct-current (HVDC) cables experiences a short period of voltage polarity reversal when the power flow is adjusted, leading to sever field distortion in this situation. Consequently, improving the insulation performance of the composite insulation structure in these cables has become an urgent challenge. In this paper, SiC-SR (silicone rubber) and TiO2-SR nanocomposites were chosen for fabricating HVDC cable accessories. These nanocomposites were prepared using the solution blending method, and an electro-acoustic pulse (PEA) space charge test platform was established to explore the electron transfer mechanism. The space charge characteristics and field strength distribution of a double-layer dielectric composed of cross-linked polyethylene (XLPE) and nano-composite SR at different concentrations were studied during voltage polarity reversal. Additionally, a self-built breakdown platform for flake samples was established to explore the effect of the nanoparticle doping concentration on the breakdown field strength of double-layer composite media under polarity reversal. Therefore, a correlation was established between the micro electron transfer process and the macro electrical properties of polymers (XLPE/SR). The results show that optimal concentrations of nano-SiC and TiO2 particles introduce deep traps in the SR matrix, significantly inhibiting charge accumulation and electric field distortion at the interface, thereby effectively improving the dielectric strength of the double-layer polymers (XLPE/SR).

Improved high temperature energy storage density and efficiency of polyimide nanocomposites via hindering charge and molecular motions

Electric vehicles and renewable energy consumption have huge demands for high-performance polymer dielectric capacitors. However, the resistivity and breakdown strength of existing polymer dielectrics deteriorate significantly at high temperatures, reducing the energy storage density and charge-discharge efficiency of capacitors below service requirements. The charge transport and molecular chain motion characteristics in linear polymers determine their conductivity, breakdown, and energy storage properties, but the quantitative relationship between them is not clear. An in-situ polymerization method was used to prepare polyimide/Al2O3 nanocomposites (PI/Al2O3 PNCs). Experimental results show that the resistivity, breakdown strength, energy storage density, and charge-discharge efficiency of PNCs increase initially and then decrease with increasing doping content, peaking at 3 wt%. The discharged energy density of PI/Al2O3-3 wt% PNCs at 180°C is 207.52 % higher than pure PI. A conductance-breakdown-energy storage co-simulation model based on charge transport and molecular chain displacement was used to simulate the voltage-current, breakdown, and energy storage characteristics of PNCs. The simulation results are consistent with the experiments. Comparative studies between simulation and experiments show that the independent interface zone between nanofillers and PI hinders charge transport and molecular chain movement, reducing electric field distortion and molecular chain spacing, thereby improving high-temperature breakdown and energy storage performance of PNCs.

Leveraging Multi-Echo EPI to Enhance BOLD Sensitivity in Task-based Olfactory fMRI.

Functional magnetic resonance imaging (fMRI) using blood-oxygenation-level-dependent (BOLD) contrast relies on gradient echo echo-planar imaging (GE-EPI) to quantify dynamic susceptibility changes associated with the hemodynamic response to neural activity. However, acquiring BOLD fMRI in human olfactory regions is particularly challenging due to their proximity to the sinuses where large susceptibility gradients induce magnetic field distortions. BOLD fMRI of the human olfactory system is further complicated by respiratory artifacts that are highly correlated with event onsets in olfactory tasks. Multi-echo EPI (ME-EPI) acquires gradient echo data at multiple echo times (TEs) during a single acquisition and can leverage signal evolution over the multiple echo times to enhance BOLD sensitivity and reduce artifactual signal contributions. In the current study, we developed a ME-EPI acquisition protocol for olfactory task-based fMRI and demonstrated significant improvement in BOLD signal sensitivity over conventional single-echo EPI (1E-EPI). The observed improvement arose from both an increase in BOLD signal changes through a T 2 * -weighted echo combination and a reduction in non-BOLD artifacts through the application of the Multi-Echo Independent Components Analysis (ME-ICA) denoising method. This study represents one of the first direct comparisons between 1E-EPI and ME-EPI in high-susceptibility regions and provides compelling evidence in favor of using ME-EPI for future task-based fMRI studies.

Enhanced energy density of BOPP film by MAH grafting for metallized capacitors

In this paper, maleic anhydride (MAH) was grafted on the surfaces of biaxially oriented polypropylene (BOPP) film by ultraviolet irradiation treatment to improve the breakdown strength. The addition of MAH, with abundant deep traps, effectively hinders charge injection from the electrode, leading to improved dielectric performance, particularly at elevated temperatures. The experimental results show that the received modified film exhibits an improved permittivity of 2.37 alongside a low dielectric loss of 0.0022 at 1000 Hz. Remarkably, the DC breakdown strength reaches 633.9 kV mm−1, marking a notable 21.4% increase compared to the unmodified BOPP film at 120 °C. Moreover, the film exhibits an energy density of 2.58 J m−3, which is 1.59 times that of the pure film. The charging and discharging efficiency is also greatly improved due to the reduction of conductance losses. Through simulation results, it becomes evident that the enhanced performance is attributed to the alleviation of electric field distortion due to the suppression of injected charge. This work paves a facile route to design scalable polymeric dielectrics with outstanding performance, which facilitates the development of film capacitors.

The mechanism of tuning filler orientation degree in composites based on AC electric field assist: from microscopic dynamical model to macroscopic electrical properties

Using the AC electric field to induce the orientation of nonlinear conductive fillers in composites is an effective solution for alleviating electric field distortion in power modules. However, the mechanism by which the electric field affects the filler dynamic characteristics and the composites’ electrical properties remains unclear. In this paper, the correlation between the microscopic dynamic processes of fillers and the macroscopic current amplitude was analyzed. The results show that the current increases rapidly (0 ∼ 173 s) and then slowly (173 ∼ 869 s) at 600 V mm−1, influenced by the rotation and attraction processes of the fillers. This demonstrates that the orientation stops at about 869 s and the filler orientation state is a key factor in determining the dielectric properties. Secondly, the global orientation evaluation index D for the filler network was proposed, which can also derive the minimum time and energy loss required for preparation. Finally, the impact of different filler orientations on the composites’ conductivity was investigated. In the low electric field stress region, with the average carrier jump distance decreasing from 150.23 to 109.71 nm as the D increases from −0.93 to −0.05. On this basis, materials with nonlinear conductivity gradient distribution can be easily prepared. Before optimization, the electric field stress of the power module at the triple point was 35.79 kV. This composite can reduce the value to 15.42 kV, a decrease of 56.9%, while maintaining good electric field uniformity.

Effect of liquid surface depression size on discharge characteristics and chemical distribution in the plasma-liquid anode system

Atmospheric pressure plasma-liquid interactions exist in a variety of applications, including wastewater treatment, wound sterilization, and disinfection. In practice, the phenomenon of liquid surface depression will inevitably appear. The applied gas will cause a depression on the liquid surface, which will undoubtedly affect the plasma generation and further affect the application performance. However, the effect of liquid surface deformation on the plasma is still unclear. In this work, numerical models are developed to reveal the mechanism of liquid surface depressions affecting plasma discharge characteristics and the consequential distribution of plasma species, and further study the influence of liquid surface depressions of different sizes generated by different helium flow rates on the plasma. Results show that the liquid surface deformation changes the initial spatial electric field, resulting in the rearrangement of electrons on the liquid surface. The charges deposited on the liquid surface further increase the degree of distortion of the electric field. Moreover, the electric field and electron distribution affected by the liquid surface depression significantly influence the generation and distribution of active species, which determines the practical effectiveness of the relevant applications. This work explores the phenomenon of liquid surface depression, which has been neglected in previous related work, and contributes to further understanding of plasma-liquid interactions, providing better theoretical guidance for related applications and technologies.

Design and development of a scanning magnet for high-resolution mass spectrometry

The magnets play a crucial role in sector mass spectrometers, directly influencing the resolution, sensitivity, and stability of these instruments. This study is based on the design requisites for high-resolution scanning magnet, alongside the optical layout schematics for mass spectrometer instrumentation. The analysis is conducted on the design parameters encompassing magnetic structure, field quality, and response dynamics. Utilizing Opera-3D simulation software, optimization designs are executed for the magnetic structure and performance, resulting in a magnet design exhibiting commendable attributes such as response time, magnetic field distortion characteristics, field range, linearity, and homogeneity. Following the completion of magnet fabrication and assembly, comprehensive evaluations of magnetic field performance and instrument testing are conducted. Results demonstrate good magnetic field linearity and minimal eddy current distortion, with a magnetic field homogeneity reaching up to ±0.05 % within the desired field region. The magnet exhibits versatility across a scan range spanning 7 to 238 u, with a scanning speed of 140 ms. Sensitivity and resolution tests, conducted using In-115, validated the magnet's compliance with the stringent design requirements of high-resolution mass spectrometry scanning magnets.

Effect of dielectric material on the uniformity of nanosecond pulsed dielectric barrier discharge

Dielectric barrier discharge (DBD) is considered as a promising technique to produce large volume uniform plasma at atmospheric pressure, and the dielectric barrier layer between the electrodes plays a key role in the DBD processes and enhancing discharge uniformity. In this work, the uniformity and discharge characteristics of the nanosecond (ns) pulsed DBD with dielectric barrier layers made of alumina, quartz glass, polycarbonate (PC), and polypropylene (PP) are investigated via discharge image observation, voltage-current waveform measurement and optical emission spectral diagnosis. Through analyzing discharge image by gray value standard deviation method, the discharge uniformity is quantitatively calculated. The effects of the space electric field intensity, the electron density (N e), and the space reactive species on the uniformity are studied with quantifying the gap voltage U g and the discharge current I g, analyzing the recorded optical emission spectra, and simulating the temporal distribution of N e with a one-dimensional fluid model. It is found that as the relative permittivity of the dielectric materials increases, the space electric field intensity is enhanced, which results in a higher N e and electron temperature (T e). Therefore, an appropriate value of space electric field intensity can promote electron avalanches, resulting in uniform and stable plasma by the merging of electron avalanches. However, an excessive value of space electric field intensity leads to the aggregation of space charges and the distortion of the space electric field, which reduce the discharge uniformity. The surface roughness and the surface charge decay are measured to explain the influences of the surface properties and the second electron emission on the discharge uniformity. The results in this work give a comprehensive understanding of the effect of the dielectric materials on the DBD uniformity, and contribute to the selection of dielectric materials for DBD reactor and the realization of atmospheric pressure uniform, stable, and reactive plasma sources.

Unraveling the nature of local field distortion-induced dual electron-trapping centers for efficient photocatalytic fuel evolution

Active electron-trapping centers play significant roles in photocatalysis. Herein, we synergize local field distortion and defects in nanocrystals to produce dual electron-trapping centers and unravel the nature of aluminum doping in porous ZnO with tunable amounts of heteroatoms and oxygen vacancies. The introduced Al atoms in the structural domain induce local field distortion and trigger the movement of Zn2+ from a singlet low spin state to a stable triplet state, resulting in the generation of free carriers trapping centers and optimized electronic energy band structure. Dual active electron-trapping centers of heteroatoms and oxygen vacancies promote the Separation of photo-generated charge carriers and reduce the adsorption energies of H* species. Furthermore, the d-band center of Al-doped ZnO with oxygen vacancies shifts to a higher energy position, thus promoting the adsorption and desorption of hydrogen intermediates and exhibiting 4-fold the photocatalytic H2 efficiency of pristine ZnO. This study provides new insights into the rational design of highly efficient oxide-based photocatalysts toward sustainable solar fuel evolution.

Electrically Induced Crystal Field Distortion in a Ferroelectric Perovskite Revealed by Electron Paramagnetic Resonance.

The magnetoelectric material has attracted multidisciplinary interest in the past decade for its potential to accommodate various functions. Especially, the external electric field can drive the quantum behaviors of such materials via the spin-electric coupling effect, with the advantages of high spatial resolution and low energy cost. In this work, the spin-electric coupling effect of Mn2+-doped ferroelectric organic-inorganic hybrid perovskite [(CH3)3NCH2Cl]CdCl3 with a large piezoelectric effect was investigated. The electric field manipulation efficiency for the allowed transitions was determined by the pulsed electron paramagnetic resonance. The orientation-included Hamiltonian of the spin-electric coupling effect was obtained via simulating the angle-dependent electric field modulated continuous-wave electron paramagnetic resonance. The results demonstrate that the applied electric field affects not only the principal values of the zero-field splitting tensor but also its principal axis directions. This work proposes and exemplifies a route to understand the spin-electric coupling effect originating from the crystal field imposed on a spin ion being modified by the applied electric field, which may guide the rational screening and designing of hybrid perovskite ferroelectrics that satisfy the efficiency requirement of electric field manipulation of spins in quantum information applications.

Defect Analysis of the Basin-type Insulator in a 500kV SF6 Current Transformer

Abstract A rigorous examination and analysis were conducted on a fault incident involving an SF6-insulated current transformer. The investigation revealed an intrinsic defect in the basin-type insulator within the current transformer, leading to a discharge pathway formation from the shell base flange to the secondary lead shielding tube. To further analyze the insulation characteristics of basin-type insulator, a three-dimensional simulation model of current transformers was established using simulation software to study the electric field distribution law of basin-type insulators with pores, metal impurity pollution, and microcracks. Simulation tests indicated that micro-cracks can result in severe electric field distortion in the basin-type insulator, followed by metal particle pollution, and bubbles cause the least degree of electric field distortion. The findings of this article can serve as a reference for the production of basin-type insulators and the operation, maintenance, and fault analysis of SF6-insulated current transformers.