Fiber Transmission Research Articles

Time Domain Spectral LiDAR Enabled by Cascaded Raman in a Hydrogen-Filled Fiber Transmitter

Time Domain Spectral LiDAR Enabled by Cascaded Raman in a Hydrogen-Filled Fiber Transmitter

Purifying quantum-dot light in a coherent frequency interface

Abstract Quantum networks typically operate in the telecom wavelengths to take advantage of low-loss transmission in optical fibres. However, bright quantum dots (QDs) emitting highly indistinguishable quantum states of light, such as InGaAs QDs, often emit photons in the near infrared thus necessitating frequency conversion (FC) to the telecom band. Furthermore, the signal quality of quantum emissions is crucial for the effective performance of these networks. In this work we report a method for simultaneously implementing spectral purification and frequency shifting of single photons from QD sources to the c-band in a periodically poled lithium niobate waveguide. We consider difference frequency generation in the counter-propagating configuration to implement FC with the output emission bandwidth in units of GHz. Our approach establishes a clear path to integrating high-performance single-emitter sources in a hybrid quantum network.

A brief analysis of spectral technology for effective utilization of full spectrum of solar energy

In this paper, a spectroscopic technology based on a trough-type parabolic condenser is proposed, which effectively utilizes the full spectrum of solar energy for light transmission through optical fibers. The technology comprises four parts, which are concentration, transmission, splitting, and detection, and its application in the field of clean energy was explored. A one-way glass is introduced into the installation as a device for light transmission restriction. The one-way transmittance of one-way glass effectively ensures the transmission direction of sunlight. According to the light simulation results from TracePro software, after the light was transmitted through the one-way glass reflection device, light intensity was guaranteed to meet usage requirements. After being focused by collimating lens and Fresnel lens, the light is introduced into a Roland circle spectroscopic system through an optical fiber. After splitting, various types of light passing through the detection system are introduced into their respective optical fibers for long-distance transmission and use. From the experiments, it was found that through reasonable splitting and the targeted use of different wavelength bands, the effective utilization of the full spectrum of solar energy significantly improved, verifying the feasibility of the device design idea.

Modulation Format Recognition Scheme Based on Discriminant Network in Coherent Optical Communication System

In this paper, we skillfully utilize the discriminative ability of the discriminator to construct a conditional generative adversarial network, and propose a scheme that uses few symbols to achieve high accuracy recognition of modulation formats under low signal-to-noise ratio conditions in coherent optical communication. In the one thousand kilometres G.654E optical fiber transmission system, transmission experiments are conducted on the PDM-QPSK/-8PSK/-16QAM/-32QAM/-64QAM modulation format at 8G/16G/32G baud rates, and the signal-to-noise ratio parameters are traversed under experimental conditions. As a key technology in the next-generation elastic optical networks, the modulation format recognition scheme proposed in this paper achieves 100% recognition of the above five modulation formats without distinguishing signal transmission rates. The optical signal-to-noise ratio thresholds required to achieve 100% recognition accuracy are 12.4 dB, 14.3 dB, 15.4 dB, 16.2 dB, and 17.3 dB, respectively.

Power-aided probabilistic shaping parameter optimization for long-haul optical fiber transmission

A power-aided probabilistic shaping (PS) parameter optimization scheme is proposed to localize the optimal transmitting setup and maximize the transmission capacity in long-haul optical fiber transmission. Using a neural network and genetic algorithm (NNGA), the proposed scheme can select the optimal transmission parameter set, including the launching optical power (LOP) and three PS characteristics. We built a testbed using MATLAB and VPI to validate the proposed scheme. The proposed scheme was demonstrated in a dual-polarization coherent transmission system. The results show that the proposed scheme improves the generalized mutual information (GMI) by 0.3035 bits/symbol/pol and normalized GMI by 0.1022 in a 1000 km G.654E fiber transmission at 420-Gbit/s, compared to a traditional MB-based PS technique. The signal-to-noise ratio (SNR) achieves a gain of 1.003 dB, which validates the outperformance of the proposed scheme.

Real-time demonstration of 64 × 200 Gbps UDWDM-PON downstream transmission based on silicon photonic integrated transceiver

Coherent detection, high-order modulation, and dense wavelength division multiplexing (DWDM) technologies provide solutions for increasing bandwidth demand of future access networks. We experimentally demonstrate a real-time 64 × 200-Gb/s coherent ultra-dense wavelength-division (UDWDM) coherent passive optical networks (PONs) at 75-GHz channel spacing. The demonstrated downlink transmission is realized with the dual-polarization QPSK (DP-QPSK) modulation scheme. The cost is reduced by using silicon photonic integrated coherent transceiver modules and wider grid AWGs. The power budget is evaluated when all 200 channels are launched at C band. The power budget is 26 dB after 20-km G.652D standard single mode fiber (SSMF) transmission without amplifier at the receiver side under soft-decision FEC (SD-FEC) threshold of 1 × 10−2, and can achieve 32.5 dB with pre-amplified semiconductor optical amplifier (SOA) used at the receiver side.

Characterization and Exploitation of the Rotational Memory Effect in Multimode Fibers

In an ideal perfectly straight multimode fiber with a circular core, the symmetry ensures that rotating the input wave front leads to a corresponding rotation of the output wave front. This invariant property, known as the rotational memory effect (RME), remains independent of the typically unknown output profile. The RME thus offers significant potential for imaging and telecommunication applications. However, in real-life fibers, this effect is degraded by intrinsic imperfections and external perturbations, and is challenging to observe because of its acute sensitivity to misalignments and aberrations in the optical setup. Building on a previously established method for precisely estimating fiber transmission properties, we demonstrate an accurate extraction of RME properties. Additionally, we introduce a comprehensive theoretical framework for both qualitative and quantitative analysis, which specifically links the angular-dependent correlation of the RME to the core deformation’s geometrical properties and the fiber’s mode characteristics. Our theoretical predictions align well with experimental data and simulations for various amounts of fiber distorsion. Finally, we demonstrate the ability to engineer wave fronts with significantly enhanced correlation across all rotation angles. This work enables accurate characterization of distributed disorder from the fabrication process and facilitates calibration-free imaging in multimode fibers. Published by the American Physical Society 2024

Demonstration of a low-complexity real-time FBMC transmitter for a spectral-efficiency IMDD system.

Filter bank multi-carriers (FBMC) have higher spectral efficiency, lower out-of-band spectrum leakage, and stronger ability to resist synchronization errors compared to orthogonal frequency-division multiplexing (OFDM), which has been widely considered as a promising solution for short-reach applications, such as passive optical networks. However, the traditional fast Fourier transform (FFT)-based FBMC scheme has quite high implementation complexity for high-speed optical communications. In this work, we proposed a low-complexity real-time FBMC transmitter scheme enabled by a single fully parallel pruned inverse FFT and simplified short prototype filter-based polyphase networks for a low-cost intensity-modulation and direct-detection (IMDD) system. Compared to the OFDM transmitter, the proposed FBMC one occupies a similar number of look-up tables and registers but saves 21% of real multipliers, reduces latency by 16.2%, and increases the data rate by 12.5%. The real-time FBMC/OFDM signals are generated with a field programmable gate array chip and 6-bit 30-GSa/s digital-to-analog converter and are experimentally demonstrated in an IMDD system. After a 20-km standard single-mode fiber transmission, the negligible power penalty can be achieved with the proposed FBMC transmitter scheme at the bit error rate of 3.8e-3 compared to the OFDM counterpart.

All-fiber spatial and wavelength gain-flattening of few-mode EDFA via mode selective coupler

The mode division multiplexing (MDM) technique together with wavelength division multiplexing (WDM) shows the great prospect to solve the capacity crunch of current standard single mode fiber (SSMF) transmission system. However, the modal and wavelength gain fluctuation fundamentally limit both the capacity and the reach of hybrid MDM-WDM transmission system. Here, we propose an all-fiber few-mode gain-flattening filter (FM-GFF) based on mode selective coupler (MSC), to effectively mitigate the gain fluctuation of few-mode erbium doped fiber amplifier (FM-EDFA) in both spatial and wavelength dimensions. With the help of genetic algorithm (GA), variable mode dependent loss spectra of cascaded MSCs can be efficiently obtained, according to the gain profile of the used FM-EDFA. Consequently, gain-flattening among all guided linearly polarized (LP) mode groups over the C-band can be realized. Simulation results reveal that, as for the spatial and wavelength gain flattening among 4/6-LP mode groups, only 5/7 cascaded MSCs are good enough to mitigate the modal and wavelength gain fluctuation from 9.89 dB and 11.79-dB to less than 0.38 dB and 0.46 dB over the C-band. Finally, we carry out experimental verification based on 2-LP mode groups gain flattening over C-band. When 3 cascaded MSCs are involved, the gain fluctuation of FM-EDFA over the C-band can be flattened from 2.46 dB to less than 0.96 dB.

[formula omitted] modified U-shaped fiber surface plasmon resonance sensor with high sensitivity

Design of optical fiber structure and sensitive material coating are two effective performance improvement approaches for fiber optic surface plasmon resonance (SPR) sensors. Here, a tungsten diselenide (WSe2) modified U-shaped fiber optic SPR sensor is proposed. It is found that the sensing performances of the proposed U-shaped probe can be controlled with the thickness of gold film, WSe2 layers, and bending radius of the U-shaped fiber. A sensitivity of 27520 nm/RIU (RIU: refractive index unit) is obtained with the optimized U-shaped probe, which is about 11.56-fold and 12.29-fold improvements over the traditional in-line transmission fiber optic SPR sensors without WSe2 coating and with monolayer WSe2, respectively. These results demonstrate a promising approach for sensitivity improvement of fiber optic SPR sensors, and the proposed WSe2 modified U-shaped fiber optic SPR sensor may have prospective potential applications in biological sensing, chemical sensing, and environmental monitoring.

12.1 terabit/second data center interconnects using O-band coherent transmission with QD-MLL frequency combs

Most current Data Center Interconnects (DCI) use intensity modulation direct detection (IMDD) configurations due to their low complexity and cost. However, significant scaling challenges allow coherent solutions to become contenders in these short reach applications. We present an O-band coherent optical fiber transmission system based on Quantum Dot—Mode Locked Lasers (QD-MLLs) using two independent free-running comb lasers, one each for the carrier and the Local Oscillator (LO). Using a comb-to-comb configuration, we demonstrate a 10 km single mode fiber, O-band, coherent, heterodyne, 12.1 Tbps system operating at 0.47 Tbps/λ using 26 λs. We used fewer comb lines (26 λs), faster symbol rate (56 GBaud) and higher constellation cardinality (32 QAM) relative to the highest capacity C-band systems reported to date. Through design, analysis, and experimentation, we quantify the optimum comb line spacing for this use case. We compare potential configurations for increasing data center interconnect capacities whilst reducing power consumption, complexity, and cost.

Dynamic perturbation mitigation via polarization difference neural network for high-fidelity ring core fiber image transmission

Ring core fibers (RCFs) offer unique advantages in fiber image transmission, as their weakly-coupled orbital angular momentum mode groups result in high resolution images. However, severe image distortion is still exhibited during fiber transmission when subjected to strong disturbances. Here, we present a novel approach with a differential neural network, namely the polarization speckle differential imaging (PSDI) method, to significantly enhance both the robustness and image resolution of RCF-based imaging systems. When the fibers are disturbed, the PSDI method establishes the perturbation mapping relationship between two polarization speckles and utilizes a differential method to eliminate the perturbation effect in the speckles. This approach mitigates environmental disturbances, resulting in an enhancement of the imaging system's robustness in dynamic environments. By addressing the limitations of conventional techniques, this research represents a significant advancement in the field of fiber imaging technology, with potential applications ranging from endoscopy to high-resolution imaging in complex and dynamic settings.

Experimental study of intramodal XPM reduction by intramodal dispersion in weakly coupled FMF.

The understanding of nonlinear propagation effects in low-crosstalk few-mode fiber is crucial for a weakly coupled mode-division multiplexed system. In this Letter, we report the first, to the best of our knowledge, experimental verification of the advantage of intramodal dispersion on mitigating intramodal cross-phase modulation in a weakly coupled few-mode fiber transmission. The experimental system is established over a 70-km multiple-ring-core few-mode fiber accommodating 6 linearly polarized modes, based on which the influences of intramodal cross-phase modulation on transmission performances of each linearly polarized mode are evaluated. Experimental results show that the intramodal cross-phase modulation of degenerate linearly polarized modes with much larger intramodal dispersion values are significantly weaker than those of non-degenerate linearly polarized modes, in which the maximum suppression of intramodal cross-phase modulation noise is up to 9.7 dB. We believe that this work would be beneficial to practical applications of weakly coupled mode-division multiplexing technologies.

Simultaneous radio/pump/power-over-multi-core fiber transmission for optically powered radio units eliminating electrical power amplifiers

Simultaneous radio/pump/power-over-multi-core fiber transmission for optically powered radio units eliminating electrical power amplifiers

Single vector mode transmission in hollow-core photonic bandgap fiber based on surface mode coupling effect

Single vector mode transmission in hollow-core photonic bandgap fiber based on surface mode coupling effect

3D printed UV-sensing optical fiber probes: manufacturing, properties, and performance

UV sensing 3D printed optical fiber hydrogels provide a flexible and precise method of remotely of detecting exposure to UV radiations. The optical fibers were created using digital light processing 3D printing technique with hydrogel composites, including micro-sized photochromic dyes (pink, blue and their combination). When exposed to ultraviolet (UV) radiation, these dyes exhibited specific absorption characteristics, resulting in significant decreases in both reflection and transmittance mode spectra at 560 nm, 620 nm, and 590 nm. Optical fibers of lengths 1, 2, and 3 cm were manufactured in two orientations: vertical and horizontal. Scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction were utilized to characterize the printed fiber probes. The optical performance of the fibers was tested using customized measurement setups. The reflection and transmission of the printed fibers reduced as the length increased due to optical losses. Reflection and transmisson loss of 20–40% can be observed when the length is increased from 1 to 3 cm. The maximum loss in reflection is observed for pink fiber in the presence of UV irradiation. Also, the type of powder used impacted the response and retraction time, whereas the mixed fiber showed the highest response time of 12–20 s under various conditions. The pink dye added fiber probes shows quick response to UV radiation. An increase in the response time is observed with increasing fiber length. The impact of printing orientation on the transmission and reflectance mode operations of optical fibers was assessed. In addition, the stability of the fiber probes are assesed using a green laser having wavelength 532 nm. This work comprehensively examines the optical properties, manufacturing procedures, and sensing capacities of UV-sensitive photochromic optical fiber sensors.

Learnable digital signal processing: a new benchmark of linearity compensation for optical fiber communications

The surge in interest regarding the next generation of optical fiber transmission has stimulated the development of digital signal processing (DSP) schemes that are highly cost-effective with both high performance and low complexity. As benchmarks for nonlinear compensation methods, however, traditional DSP designed with block-by-block modules for linear compensations, could exhibit residual linear effects after compensation, limiting the nonlinear compensation performance. Here we propose a high-efficient design thought for DSP based on the learnable perspectivity, called learnable DSP (LDSP). LDSP reuses the traditional DSP modules, regarding the whole DSP as a deep learning framework and optimizing the DSP parameters adaptively based on backpropagation algorithm from a global scale. This method not only establishes new standards in linear DSP performance but also serves as a critical benchmark for nonlinear DSP designs. In comparison to traditional DSP with hyperparameter optimization, a notable enhancement of approximately 1.21 dB in the Q factor for 400 Gb/s signal after 1600 km fiber transmission is experimentally demonstrated by combining LDSP and perturbation-based nonlinear compensation algorithm. Benefiting from the learnable model, LDSP can learn the best configuration adaptively with low complexity, reducing dependence on initial parameters. The proposed approach implements a symbol-rate DSP with a small bit error rate (BER) cost in exchange for a 48% complexity reduction compared to the conventional 2 samples/symbol processing. We believe that LDSP represents a new and highly efficient paradigm for DSP design, which is poised to attract considerable attention across various domains of optical communications.

Design and performance of WDM system for high-speed optical communication on different modulation formats

Abstract In this paper, the performance analysis of the WDM (wavelength division multiplexing) system on the optical fiber transmission link is proposed. High data transmission is possible by implementing a WDM optical communication system using different modulation formats. Firstly, the WDM optical communication system is designed on an Optiwave simulation tool and distortion in the optical fiber by “eye pattern analysis” is analyzed. Secondly, the optical SNR of the proposed WDM optical communication system is studied. Further, the bit-error rate (BER) plot is studied and optimization techniques are applied to enhance the proposed system for long-haul communication. Furthermore, the BER plots are analyzed by varying the length of the fiber and applying different coding techniques like NRZ (non-return zero), RZ (return to zero), QAM (quadrature amplitude modulation) etc. using the Optiwave simulation tool. The results obtained in the Optiwave simulation tool are validated by theoretical implementation in the MATLAB tool.

Multiple-signal-joint-processing-based guard interval shortening method for a CS-NFDM system.

Aiming to further improve the spectral efficiency (SE) of a continuous spectrum modulated nonlinear frequency division multiplexing (CS-NFDM) system, we propose a novel ,to the best of our knowledge, multiple-signal-joint-processing (MSJP)-based guard interval (GI) shortening method. In this method, multiple NFDM time-domain signals are jointly processed as a whole to carry out nonlinear Fourier transform and inverse nonlinear Fourier transform (NFT-INFT) operations. These operations can fuse the multiple NFDM time-domain signals together, which is equivalent to the corresponding inverse process of a fiber transmission. Experimental results show that the normalized SE of the proposed method can reach 0.99 when approaching the limit value of 1 and obtain a 2.33 dB Q2-factor improvement compared with the pre-dispersion compensation (PDC) method under the same GI of 0.03 ns in an 80 km SSMF transmission of a 46 GHz signal bandwidth. Furthermore, in comparison with the PDC method, the proposed method can achieve 32.86% normalized SE improvement in the 1120 km SSMF transmission of 32 GHz signal bandwidth under the SD-FEC of 2.4E-2.

Transceiver impairment robust and joint monitoring of PDL, DGD, and CD using frequency domain pilot tones for digital subcarrier multiplexing systems

Optical performance monitoring is vital for enabling dynamically reconfigurable optical networks. This paper introduces a monitoring scheme that is robust to transceiver impairments for coherent digital subcarrier multiplexing (DSCM) systems that simultaneously monitors polarization-dependent loss (PDL), differential group delay (DGD), and chromatic dispersion (CD). In the proposed scheme, a pair of frequency domain pilot tones (FPTs) are inserted into the X and Y polarizations of the transmitted dual-polarization signal. Both the signal and the FPTs endure identical channel impairments during fiber transmission. At the receiver side, the transmitted FPTs are extracted to monitor the channel impairments. We begin by establishing a simplified system model using a single frequency tone to analyze the effects of system impairments on the frequency domain pilots. Based on this model, CD, PDL, and DGD are jointly and accurately estimated. In addition, the influences of temporal, amplitude, and phase mismatches between in-phase (I) and quadrature (Q) components of transceivers on channel impairment monitoring are completely eliminated. This achieves a channel impairment monitoring scheme that is robust to transceiver impairments. Experimental verification shows that the proposed scheme can jointly and accurately estimate a wide range of CD, PDL, and DGD. Additionally, the proposed monitoring scheme demonstrates strong robustness against transceiver impairments, rapid polarization fluctuations, and amplified spontaneous emission (ASE) noise.