Fiber Membrane Research Articles

Natural filter: Adjustable hydrophobicity from biodegradable zein nanofiber membrane for high efficiency air purification

Faced with the fact that air filtration materials prepared from traditional petroleum-based materials do not have good biodegradability and have the risk of causing secondary pollution to the environment, a kind of nanofiber membrane with biodegradable polylactic acid (PLA) and zein was prepared by electrospinning method. The morphology of as-prepared membrane was carried out along with filtration performance and degradation performance both experimentally and theoretically. The results showed that the hydrophobicity of nanofiber membrane can be adjusted by changing the ratio of PLA and zein. In addition, the highest filtration efficiency for PM2.5 and PM10 was achieved when the ratio of PLA to zein was 1:1, and it could be stabilized at 98.14 % and 97.39 %, and had the highest quality factor (QF) of 0.00738 Pa−1. Moreover, the fiber membrane has excellent adsorption effect on aqueous particles as well as oily particles. Notably, the as-prepared composite filter can be easily biodegraded thus contributing to green ecological environment.

A robust floating oxygen-doped graphitic carbon nitride sheet for efficient photocatalytic CO2 conversion

Photocatalytic CO2 reduction offers a promising approach for converting CO2 into valuable chemicals. However, typical conversion systems suffer from inefficient CO2 mass transfer and complex recycling processes. In this study, we developed a floating sheet as a robust photocatalytic CO2 conversion system by integrating graphitic carbon nitride (CN) nanosheets onto polytetrafluoroethylene (PTFE) fiber membrane, followed by oxygen (O) doping into the CN (CN-O) via oxygen-plasma treatment. The floatable CN-O/PTFE sheet exhibits slight wettability in water under 0.25 MPa of CO2 pressure in our reactor system, facilitating the delivery of dissolved CO2 to the CN-O photocatalyst surface. O-doping enhances the visible light absorption and improves the separation and transport efficiency of photogenerated electrons and holes due to O-doping-induced states in CN. Consequently, the floating CN-O/PTFE system achieves an exceptional photocatalytic CO2 conversion rate of 102.3 μmol g-1h−1, approximately 4.8 times higher than a conventional CN-powder dispersion system in water. Moreover, the sheet demonstrates excellent cycling durability, with no significant exfoliation of the catalytic layer or reduction in CO2 photoreduction activity after 20 consecutive cycles. This study presents a novel approach to designing photocatalytic systems for efficient CO2 conversion.

PCL/soy peptide nanofibers incorporated with riboflavin/HP-β-CD assemblies for improving fruit storage quality

In this study, we first successfully developed functionalized electrospun nanofibers (PCL/SP/ICs) loaded with Riboflavin (RF) for fruit preservation with inclusion complexes (RF/HP-β-CD, IC) formed by encapsulating RF with hydroxypropyl-β-cyclodextrin (HP-β-CD) as a core material and soy peptide-assisted polycaprolactones (PCL/SP) as an overwrap material. Compared to 1 wt% and 5 wt% IC, nanofibers implanted with 3 wt% IC had an acceptable water contact angle (87.40°), good thermal stability, and superior mechanical properties. Also, RF/HP-β-CD integration conferred antimicrobial and antioxidant capabilities to PCL/SP fiber membranes. High-performance liquid chromatography (HPLC) studies revealed that produced films of PCL/SP/ICs could continuously and controllably release RF (within 200 h), hence retarding grape degradation and decreasing mass loss rate and titratable acid content throughout an 8-day storage period. Based on these findings, electrospun nanofiber films may be useful for vitamin loading in active food packaging.

The preparation of melt electrospun fiber containing tandospirone for drug sustained release

AbstractElectrospun fibers membrane is considered an efficient drug carrier for transdermal drug delivery due to its breathability and high drug loading percentage, compared with coating film. However, pollution and safety risk caused by the use of organic solvents during the solution electrospinning process limit its industrialization and direct application in the biomedical field. Herein, a fiber membrane containing tandospirone was prepared using the melt electrospinning process and to be used for sustained drug release. The process of fiber preparation is an eco‐friendly and safe process due to the characteristics of solvent‐free. The in vitro drug release results showed that the fiber membranes containing tandospirone had slower initial drug release and higher end drug release compared with coating film containing tandospirone. The sustained‐release property can be attributed to the crystalline structure of fibers and the higher‐end drug release can be attributed to the spatial packing structures in the fiber membrane. The large pores generated by the stack structure of the large fiber in the fiber membrane leads to low gas resistance (10.7 Pa), which is much lower than that of the coating film (511.2 Pa). Overall, this study presents a green and safe preparation method of fiber membrane containing tandospirone, providing an effective and adjunctive treatments for mental disorders.Highlights The tandospirone‐loaded fiber patch was prepared using an eco‐friendly method. Burst release inhibition and higher final release of tandospirone in fibers. The fiber patch provided excellent breathability compared to coating patch. Fibers with higher crystallinity showed better controlled release.

Semaglutide functional electrospinning nanofiber membrane rescues apoptosis and promotes diabetic wound healing

The healing of diabetic wounds is a difficult problem due to decreased proliferation, and migration of epidermal and endothelial cells. Here we reported semaglutide-loaded nanofiber membrane to promote diabetic wound healing through suppressing reactive oxygen species production and accelerating angiogenesis in a diabetic rat model. The fiber membrane was prepared by an electrostatic spinning technique. The fiber membrane consisted of thermalplastic polyurethane elastomer, polyvinyl butyral ester, zein and semaglutide (SMGT). The fiber membrane had a uniformly distributed diameter, suitable water vapor transmission rate, good water absorption and retention properties. In vivo data determined that the SMGT-loaded nanofiber membrane was able to promote normal skin pathological structure formation in regenerated tissue. In vitro experiments displayed that SMGT might facilitate HG-induced endothelial cell dysfunction by inhibiting ROS production. The present study provided a theoretical basis for the extensive application of SMGT in the treatment of diabetic ulcers and other wounds.

Preparation and insecticidal performance of 1,8-cineole/cellulose acetate electrospun fibrous membranes

Plant essential oils and their components have broad application prospects as substitutes for chemical pesticides. However, the burst release and persistence time need to be optimized. In this study, 1,8-cineole (1,8-CIN) was embedded in degradable cellulose acetate (CA) by electrospinning to achieve sustained release. The results showed that the sustained-release membrane had good morphology and thermal stability. The release test showed that the deficiency of the explosive release of 1,8-CIN improved after encapsulation, and 21.74 % of the drug remained after 42 days. In the application test, the fiber membrane could kill the test insects in a short period of time and affect the behavior choices of the test insects. It affected the growth and oviposition of the test insects and reduced adult longevity by 13.64 % and oviposition by 23.35 %. This study can improve the utilization rate of pesticides, alleviate environmental pressure, and provide new ideas for pest control.

Preparation of thermally conductive polyimide/aluminum oxide/boehmite composite separators for enhancing lithium‐ion battery safety and performance

AbstractThis study endeavors to enhance the safety of lithium‐ion batteries (LIBs) by synthesizing a polyamide acid (PAA)/Al2O3 composite spinning solution using 4,4′‐diaminodiphenyl ether (ODA) and pyromellitic anhydride (PMDA) as monomers, and nano‐Al2O3 as a thermal conductivity filler. Subsequently, the PAA/Al2O3 fiber membrane is fabricated via electrostatic spinning, followed by gradient heating imidization to produce a polyimide (PI)/Al2O3 composite membrane. This membrane is then dipped into a boron nitride (BM) slurry to ultimately yield an organic–inorganic PI/Al2O3/BM composite separator with superior flame‐retardant and thermal conductivity properties. The thermal stability, flame retardancy, electrolyte wettability, mechanical integrity, and cycle rate performance of the composite membranes are rigorously evaluated. The results demonstrate that the PI/5% Al2O3/BM composite membrane exhibits the most favorable overall performance, with no shrinkage observed at 200°C and no significant changes after sustained ignition for 10 s. The incorporation of the thermal conductivity Al2O3 filler significantly enhances the heat transfer properties of the composite separator. The room temperature ionic conductivity reaches 2.786 mS cm−1 after electrolyte absorption, and the initial discharge capacity of the assembled battery is 156.28 mAhg−1. Following 100 charge/discharge cycles at 0.2C, the capacity retention rate is 97.7%, and at a discharge rate of 5C, the capacity retention rate is 74.9%.

Amino acid-crosslinked 4arm-PLGA Janus patch with anti-adhesive and anti-bacterial properties for hernia repair

Presently, the non-biodegradable polypropylene (PP) patches frequently used for hernia repair can cause fibrous tissue growth and adhesions. This study created a Janus Patch with anti-adhesion and antimicrobial properties to improve hernia repair while promoting tissue repair. The biologically active 4arm-PLGA-BLPD was initially synthesized through the modification of 4arm-PLGA with lysine, followed by the fabrication of a Janus patch using a layer-by-layer electrostatic spinning technique. This patch consisted of three layers: a repair layer composed of 4arm-PLGA-BLPD/PCL fiber membrane, a mechanical layer of 4arm-PLGA/PCL fiber membrane, and an antimicrobial layer of EMO-4arm-PLGA/PCL fiber membrane loaded with Emodin (EMO). The results showed that Janus patch exhibited notable tensile strength and elongation at break, enabling it to offer enhanced mechanical reinforcement for abdominal wall defects. In addition, it slowly releases lysine for repair and inhibits bacterial growth with EMO. In vivo experiments demonstrated that the patch effectively induced neovascularization, reduced collagen ac-cumulation, and stabilized the expression of relevant proteins through the up-regulation of MMP1 and MMP9. This facilitated successful repair of the abdominal wall defect model and prevented adhesions. In summary, the Janus patch offers both practical application and theoretical insight for hernia repair.

Electrospun fluorinated poly(aryl ether) fiber membrane: preparation and high triboelectric output performance

Electrospun fluorinated poly(aryl ether) fiber membrane: preparation and high triboelectric output performance

An Integrated and Modular Compartmentalized Microfluidic System with Tunable Electrospun Porous Membranes for Epithelialized Organs-on-a-Chip.

A modular and 3D compartmentalized microfluidic system with electrospun porous membranes (PMs) for epithelialized organ-on-a-chip systems is presented. Our novel approach involves direct deposition of polymer nanofibers onto a patterned poly(methyl methacrylate) (PMMA) substrate using electrospinning, resulting in an integrated PM within the microfluidic chip. The in situ deposition of the PM eliminates the need for additional assembly processes. To demonstrate the high throughput membrane integration capability of our approach, we successfully deposited nanofibers onto various chip designs with complex microfluidic planar structures and expanded dimensions. We characterized and tested the fully PMMA chip by growing an epithelial monolayer using the Caco-2 cell line to study drug permeability. A comprehensive analysis of the bulk and surface properties of the membrane's fibers made of PMMA and polystyrene (PS) was conducted to determine the polymer with the best performance for cell culture and drug transport applications. The PMMA-based membrane, with a PMMA/PVP ratio of 5:1, allowed for the fabrication of a uniform membrane structure along the aligned nanofibers. By modulating the fiber diameter and total thickness of the membrane, we could adjust the membrane's porosity for specific cell culture applications. The PMMA-PVP nanofibers exhibited a low polydispersity index value, indicating monodispersed nanofibers and a more homogeneous and uniform fiber network. Both types of membranes demonstrated excellent mechanical integrity under medium perfusion flow rates. However, the PMMA-PVP composition offered a tailored porous structure with modulable porosity based on the fiber diameter and thickness. Our developed platform enables dynamic in vitro modeling of the epithelial barrier and has applications in drug transport and in vitro microphysiological systems.

Nanofiber membranes fabricated by coaxial electrospinning with porous channel structure for high-efficiency oil-water separation

The electrospinning nanofiber membranes modified by nanoparticles can effectively improve anti-oil adhesion and separation performance. However, the low stability of nanoparticles on the fiber membrane surface substantially limits the operational lifespan of the membrane. Herein, poly(vinylidene fluoride) (PVDF) nanofiber membranes with multi-scale microporous channel structures are prepared using coaxial electrospinning and a sacrificial template strategy. Subsequently, iron phytate nanoparticles are grown in situ on the fibers to fill the porous structures by utilizing the hollow and porous nanofibers as a framework. The interlocking structure between the nanoparticles and the porous fibers significantly enhances the stability and durability between nanoparticles and the fiber membrane. Even after being subjected to ultrasonic treatment for 7 h, there is no discernible shedding of nanoparticles from the fiber membrane. The prepared nanofiber membrane demonstrates exceptional superhydrophilicity and underwater superoleophobicity, exhibiting remarkable self-cleaning capability and resistance to crude oil contamination. Additionally, the membrane efficiently separates various oil-in-water emulsions, achieving a high separation efficiency of over 99%. Moreover, the membrane also demonstrates excellent adsorption capability towards cationic dyes. Therefore, this interlocking structure composed of nanoparticles and nanofibers presents new ideas and insights for the preparation of high-performance and durable oil–water separation membranes.

Electrochemical degradation of small molecule dyes by TiO2-decorated polyacrylonitrile nanofiber membranes with superior properties

To optimize the uniform dispersion of nanoparticles and enhance their catalytic degradation effect on small molecule dyes in textile wastewater, titanium dioxide (TiO2) was deposited on polyacrylonitrile (PAN) fiber membranes using magnetron sputtering technology, and TiO2/PAN nanofiber membrane (NFM) with low content and high catalytic efficiency was successfully prepared. Through membrane separation coupling electrocatalysis, the composite membranes exhibited outstanding performance in removing Congo red (CR), Sunset yellow (SY), Methyl orange (MO), and Methylene blue (MB) dyes, with removal rates of 99.5%, 98.8%, 98.5%, and 87.2% respectively. Even after continuous catalysis for 10 h, the composite membranes maintained a high dye removal rate, demonstrating their remarkable stability and water treatment capabilities. Furthermore, TiO2/PAN NFMs displayed high pure water permeance, dye permeance, and mechanical strength. Specifically, M20 (magnetron sputtering time of 20 min) showed water permeance and dye (SY) permeance values of 1944 L·m−2·h−1·bar−1 and 816 L·m−2·h−1·bar−1, respectively, and indicate superior mechanical and electrochemical properties. During the electrocatalytic process, TiO2/PAN NFMs generated reactive oxygen species (ROS) on the surface, imparting a self-cleaning property that extended the service life of the membranes and offered an effective solution for textile wastewater treatment.

“Sandwich” Structure (PLA/Thymol Fibre Membranes/SAP/Paper Fibre) Antibacterial Pad for Preservation of Chilled Mutton

ABSTRACTThe antibacterial pad was developed to solve the preservation problem of chilled mutton. The antibacterial pad was a “Sandwich” structure (PLA/thymol fibre membranes/SAP/paper fibre), which could absorb water and inhibit bacteria. The fibre membranes are prepared by electrostatic spinning technology. The successful incorporation of thymol into the fibre membranes was proved by FTIR, SEM and water contact angle analysis. The release experiment showed that the fibre membranes (PLA/thymol) had a slow‐release effect, especially in fatty food simulants. According to the antibacterial experiment, the antibacterial pad had a significant inhibition effect on Escherichia coli and Staphylococcus aureus (the inhibition zone was 25 ~ 26 mm). In addition, the total viable count, total volatile alkaline nitrogen, pH value and drip loss showed that the antibacterial pads could effectively extend the shelf life of chilled mutton for 6 days. Therefore, the antibacterial pad has broad application prospects in meat preservation.

Rice Bran Valorization through the Fabrication of Nanofibrous Membranes by Electrospinning

The high production rate of fossil-based plastics, coupled with their accumulation and low degradability, is causing severe environmental problems. As a result, there is a growing interest in the use of renewable and natural sources in the polymer industry. Specifically, rice bran is a highly abundant by-product of the agro-food industry, with variable amounts of protein and starch within its composition, which are usually employed for bioplastic development. This study aims to valorize rice bran through the production of nanofiber membranes processed via electrospinning. Due to its low solubility, the co-electrospinning processing of rice bran with potato starch, known for its ability to form nanofibers through this technique, was chosen. Several fiber membranes were fabricated with modifications in solution conditions and electrospinning parameters to analyze their effects on the synthesized fiber morphology. This analysis involved obtaining micrographs of the fibers through scanning electron microscopy (SEM) and fiber diameter analysis. Potato starch membranes were initially investigated, and once optimal electrospinning conditions were identified, the co-electrospinning of rice bran and potato starch was conducted. Attempts were made to correlate the physical properties of the solutions, such as conductivity and density, with the characteristics of the resulting electrospun fibers. The results presented in this study demonstrate the potential valorization of a rice by-product for the development of bio-based nanofibrous membranes. This not only offers a solution to combat current plastic waste accumulation but also opens up a wide range of applications from filtration to biomedical devices (i.e., in tissue engineering).

Dual Functional Antibacterial-Antioxidant Core/Shell Alginate/Poly(ε-caprolactone) Nanofiber Membrane: A Potential Wound Dressing.

Core/shell nanofibers offer the advantage of encapsulating multiple drugs with different hydrophilicity in the core and shell, thus allowing for the controlled release of pharmaceutic agents. Specifically, the burst release of hydrophilic drugs from such fiber membranes causes an instantaneous high drug concentration, whereas a long and steady release is usually desired. Herein, we tackle the problem of the initial burst release by the generation of core/shell nanofibers with the hydrophilic antibiotic drug gentamycin loaded within a hydrophilic alginate core surrounded by a hydrophobic shell of poly(ε-caprolactone). Emulsion electrospinning was used as the nanofibrous mesh generation procedure. This process also allows for the loading of a hydrophobic compound, where we selected a natural antioxidant molecule, betulin (BTL), to detoxify the radicals. The resulting nanofibers exhibited a cylindrical shape with a core/shell structure. In vitro tests showed a controlled release of gentamicin from nanofibers via diffusion. The drug reached 93% release in an alginate hydrogel film but only 50% release in the nanofibers, suggesting its potential to minimize the initial burst release. Antibacterial tests revealed significant activity against both Gram-negative and Gram-positive bacteria. The antioxidant property of betulin was confirmed through the DPPH assay, where the incorporation of 20% BTL revealed 37.3% DPPH scavenging. The nanofibers also exhibited favorable biocompatibility in cell culture studies, and no harmful effects on cell viability were observed. Overall, this research offers a promising approach to producing core/shell nanofibrous mats with antibacterial and antioxidant properties, which could effectively address the requirements of wound dressings, including infection prevention and wound healing acceleration.

Preparation and Application of pH‐Sensitive Protein Nanofibre Membrane Loaded With Alizarin and Curcumin for Meat Preservation

ABSTRACTA pH‐sensitive protein fibre membrane was prepared using alizarin (ALI), curcumin (CUR), gelatin, zein and cinnamaldehyde as raw materials, by electrospinning technology. The membrane was developed to detect food deterioration and extend shelf life. It was observed that the addition of CUR significantly enhanced the antioxidant and barrier properties of the membrane. The fibre membrane was responsive to pH with minimal colour alteration in response to humidity (from 20% to 80% relative humidity) and demonstrated excellent reusability along with a low detection limit for ammonia gas. Moreover, it was capable of monitoring low concentrations of bacteria in the headspace. To assess the efficacy of the membrane, a freshness monitoring and preservation study was carried out on pork stored at 4°C for 5 days. The fibre membrane not only prolonged the shelf life of meat but also allowed real‐time monitoring of its freshness. The results highlight the potential application of the prepared nanofibres in the simultaneous monitoring and preservation of meat freshness.

Electrospun medicated gelatin/polycaprolactone Janus fibers for photothermal-chem combined therapy of liver cancer

Liver cancer is a common cancer in the world, and core-shell nanoparticles as a commonly used combination therapy for local tumor ablation, have many shortcomings. In this study, photothermal Janus nanofibers were prepared using a electrospinning technology for tumor treatment, and the products were characterized and in vitro photothermal performance investigated. The micromorphology analysis showed that the photothermic agent CuS and electrospun fibers (loaded with CuS and anticancer drug dihydromyricetin) were successfully prepared, with diameters of 11.58 ± 0.27 μm and 1.19 ± 0.01 μm, respectively. Water contact angle and tensile test indicated that the fiber membranes has a certain hydrophilic adhesion and excellent mechanical strength. The fiber membranes has 808 nm near-infrared laser photothermal heating performance and photothermal stability, and it also has a strong response to the laser that penetrates biological tissue. In addition, in vitro cell culture and in vivo implantation study showed that the fiber membranes could kill HepG2 hepatocellular carcinoma cells combined with photothermal-chem and could be enriched in the implantation area, respectively. Hence, the Janus membranes may be a potential cancer treatment material.

Preparation and good antibacterial properties of self-assembled P(AA-AM)/CA/GA fiber membrane by electrospinning

To reduce mortality rate caused by life-threatening bacterial infections, advanced antibacterial materials have attracted widespread attention from researchers worldwide. In this study, the antibacterial P(AA-AM)/CA/GA nanofiber membranes with pH-responsive properties were successfully prepared by facile electrospinning technology. A series of characterizations of the obtained nanofiber membranes showed the addition of P(AA-AM) improves the surface wettability of the as-spun fibers in comparison to those of CA and CA/GA nanofiber membranes. High-temperature treatment was found to enhance the mechanical properties of the P(AA-AM)/CA/GA membranes due to the crosslinking reactions. The prepared P(AA-AM)/CA/GA nanofiber membrane exhibits a pH-responsive effect which is evident by the change in GA’s release rate in solutions with different pH values. The cellulose acetate (CA) spinning nanofiber structure formed by P(AA-AM) coated GA also extended the release process of GA and improved the antibacterial timeliness of nanofiber membranes. The antibacterial experiments on E. coli and S. aureus showed that the electrospun nanofiber membranes containing GA had potent antibacterial properties, which were further enhanced by increasing the GA content in the P(AA-AM)/CA/GA blends. This study provides an insight into the design and preparation of pH-sensitive antibacterial materials using facile electrospinning technology.

Hydrochromic convertibility on fiberized self-assembling of copper-based perovskite quantum dots

Halide perovskite presents great competitive advantages in the new generation of stimuli-responsive materials, while the tuning of fluorescence emission is still limited by irritative factors and external conditions. Herein, anti-solvent assisted crystallization and in-situ synthesis are innovatively combined to accomplish the fiberized self-assembly of copper-based perovskite quantum dots economically and environmentally, which makes humidity a novel stimulus for luminescence regulation. Under the excitation of medium-wave UV, the original Cs3Cu2I5-CsCu2I3@polyacrylonitrile (CCI@PAN) fibers exhibit a main emission peak of 460 nm with a shoulder at 550 nm, and the intensity of shoulder peak is gradually increased with the continuous addition of moisture. Switching from blue to yellow fluorescence is achieved in CCI@PAN fiber membrane by the introduction of water, which is attributed to the ultra-high solubility of CsI in water. Moreover, owing to the spatial limitation of the nanofibers, the unique incomplete reversibility exhibited by the nanofiber membrane during water removal predicts that the nanofiber membrane can be used as a permanent recording material. Overall, this work deeply explores the influence of humidity on the fluorescence and structure of perovskite quantum dots, providing a method to synthesize innovative perovskite nanofiber composites based on emission conversion, which has broad prospects in advanced anti-counterfeiting, biological protection display, information encryption and smart wearable devices.

3D-CFD Modeling of Hollow-Fiber Membrane Contactor for CO2 Absorption Using MEA Solution.

Membrane technology is considered an innovative and promising approach due to its flexibility and low energy consumption. In this work, a comprehensive 3D-CFD model of the Hollow-Fiber Membrane Contactor (HFMC) system for CO2 capture into aqueous MEA solution, considering a counter-current fluid flow, was developed and validated with experimental data. Two different flow arrangements were considered for the gas mixture and liquid solution inside the HFMC module. The simulation results showed that the CO2 absorption efficiency was considerably higher when the gas mixture was channeled through the membranes and the liquid phase flowed externally between the membranes, across a wide range of gas and liquid flow rates. Sensitivity studies were performed in order to determine the optimal CO2 capture process parameters under different operating conditions (flow rates/flow velocities and concentrations) and HFMC geometrical characteristics (e.g., porosity, diameter, and thickness of membranes). It was found that increasing the membrane radius, while maintaining a constant thickness, positively influenced the efficiency of CO2 absorption due to the higher mass transfer area and residence time. Conversely, higher membrane thickness resulted in higher mass transfer resistance. The optimal membrane thickness was also investigated for various inner fiber diameters, resulting in a thickness of 0.2 mm as optimal for a fiber inner radius of 0.225 mm. Additionally, a significant improvement in CO2 capture efficiency was observed when increasing membrane porosity to values below 0.2, at which point the increase dampened considerably. The best HFMC configuration involved a combination of low porosity, moderate thickness, and large fiber inner diameter, with gas flow occurring within the fiber membranes.