Fiber Coupling Research Articles

Fabrication and characterization of indium fluoride multimode fused fiber couplers for the mid-infrared.

Results of the fabrication and characterization of optical fiber couplers made of multimode step-index fluoroindate (InF3) fibers are presented. The fabrication setup was customized for this type of glass with a constant source of controlled nitrogen flow heated to a target temperature with an accuracy ±1°C. Combined with a novel fast fusion approach and with excellent control of the viscosity throughout the process, the clean gas flow and well-controlled temperature enable the fabrication of fused fiber couplers absent of any noticeable crystallization. A coupling ratio of 45/55 was achieved, with an excess loss of 0.35 dB, at 1.7 µm. To the best of our knowledge, this represents the first low excess loss (<1 dB), multimode, InF3 fiber couplers.

KSPGD algorithm to restrain the influence of measurement noise in adaptive fiber coupling

KSPGD algorithm to restrain the influence of measurement noise in adaptive fiber coupling

A Coaxial Dual-Waveguide Fiber Coupler

We demonstrate a method to fabricate an in-fiber integrated multi-waveguide fiber coupler based on thermal diffusion technology to achieve stable and efficient coupling of a single-mode fiber to a multi-waveguide fiber. Simulation results show that the efficient coupling of a single-mode fiber and a multi-waveguide fiber can be realized by introducing double-clad fiber into single-mode fiber and multi-waveguide fiber. A coaxial dual-waveguide fiber coupler was fabricated based on thermal diffusion technology. The measurement results of the three-dimensional refractive index distribution of the coaxial dual-waveguide fiber coupler verified the feasibility of the thermal diffusion technology to fabricate the multi-waveguide fiber coupler. The insertion loss of the thermally diffused coaxial dual-waveguide fiber coupler was tested, and its performance was better than that of the fusion tapered coupler. The multi-waveguide fiber coupler fabricated by thermal diffusion technology allows for an all-fiber setup with coupling efficiency as high as 98%, achieves a relatively stable fundamental mode excitation in multi-waveguide fiber, requires minimal maintenance, and will accelerate the translation toward particle trapping, spectral detection, and optical communication.

Adjustable spatial filter for optimal free-space quantum communication round the clock.

Free-space quantum communication in daylight relies crucially on spatial filtering. The optimal filter configuration, however, depends on ever-changing link conditions. To this end, we developed an adjustable spatial filter that can be used to change the system field of view on the fly. We demonstrate its use in quantum key distribution over a 1.7-km free-space link. Furthermore, we compare it to filtering with multi-mode fiber coupling. Finally, we extrapolate our results to a broader range of realistic link conditions and show that active field-of-view optimization has the potential to substantially improve the overall secure key output of the system.

Multimode optical fiber interrogator-based LiDAR for intravenous drip monitoring

A novel intravenous dripping monitoring system is proposed and demonstrated. The system employs a multimode optical fiber-based and low-cost LiDAR. By using an ESP32 microchip, a TF-mini-s LiDAR module is controlled. Both devices are embedded in a 3D-printed casing, and by using a multimode optical fiber coupler, the system interacts with a typical intravenous system. This interrogator configuration has a high-resolution time of 20 ms, a good signal-to-noise ratio (<13 dB), low power consumption, and maximal flow rate monitoring of 93 drops per minute. The proposed system is a novel-intensity LiDAR application that can be applied in micro-fluidics, agriculture, and drug delivery monitoring.

Optimization and demonstration of a bidirectional output linear-cavity fiber laser with a record high power of 2 × 4 kW

The bidirectional output fiber laser can achieve two laser outputs from a single resonant cavity, which can reduce the volume and cost of high-power fiber laser systems and has good application prospects in the industry. In this work, we demonstrated a bidirectional output fiber laser oscillator structure, and a total output power of 8 kW at the 2 ports × 4 kW level was achieved experimentally for the first time. In order to suppress stimulated Raman scattering (SRS) and transverse mode instability (TMI), the double cladding ytterbium-doped fiber with a core/cladding diameter of 30/400 µm, a pair of matched output coupler fiber Bragg gratings (OCFBG) with a 3 dB bandwidth of 2 nm, and the pump source with wavelength-stabilized 981 nm laser diodes (LDs) were employed. The effect of the coiling method and diameter of the active fiber on the optical-to-optical (O-O) efficiency and TMI threshold were studied intensively. The comparison of laser performance with a unidirectional output oscillator was further exploited, and results indicated that the bidirectional output fiber laser oscillator possessed a higher O-O efficiency and TMI threshold. By optimizing the fiber coiling diameter and coiling method, we finally achieved a total laser output power of 8169 W (3769 W at end A and 4400 W at end B), with an efficiency of 74.6% and beam quality of M2A ∼ 2.13, M2B ∼ 2.36, while the total output power achieved by unidirectional output structure was only 5805 W with signs of TMI. To the best of our knowledge, it is the highest output power of the bidirectional output fiber laser.

Enhancing interfacial adhesion through coupling agent incorporation in plywood/ plastic waste composite materials

The objective this study was to fabricate 5-ply boards using virgin and recycled high-density polyethylene (vHDPE and rHDPE) films as formaldehyde-free adhesives, respectively. To enhance the interfacial adhesion between the wood veneer and HDPE film, various loadings (0, 3, 6, 8, and 11 wt%) of polyethylene grafted maleic anhydride (PE-g-MA) were applied as a coupling agent. The physical and mechanical performance of the resulting plywood boards was evaluated using standard test methods, with a UF resin-bonded plywood used as a control for comparison. All materials used were for commercial-scale plywood production. Fourier transform infrared spectroscopy (FT-IR) results provided valuable information about chemical interactions that occurred during the coupling of poplar fibers with HDPE using PE-g-MA. The experimental results showed that the mechanical and physical properties of the plywood boards improved as the amount of coupling agent increased from 0 to 11 wt%. PE-g-MA played a crucial role in the properties of plywood boards made with rHDPE and vHDPE by enhancing the interfacial bonding ability between the HDPE and adjacent veneers, leading to good stress propagation and improved mechanical properties. The properties of samples bonded with vHDPE were significantly more improved than those made with rHDPE, likely due to the presence of color pigments, additives, fillers, and impurities in the rHDPE, which made the coupling agent less effective. In addition, the results demonstrated that the samples made with rHDPE and vHDPE were superior to the plywood bonded with UF resin (control), and the optimal content of the coupling agent was found to be 8 and 11 wt%. These findings suggest that incorporating recycled HDPE films and using coupling agents, such as PE-g-MA, can produce high-quality plywood composite materials with improved mechanical and physical properties, providing an eco-friendly alternative to traditional UF resin-bonded plywood.

Seismic monitoring of rockfalls using distributed acoustic sensing

Distributed acoustic sensing (DAS) using fiber-optic cables shows promise for rockfall monitoring by potentially offering high spatial resolution and wide coverage at lower costs. However, further research is needed to fully evaluate DAS performance for rockfall applications. This study assesses DAS capabilities for rockfall monitoring by analyzing DAS and seismometer recordings of 38 artificially triggered rockfalls with block masses ranging from 139.6 to 638 kg. Results demonstrate strong correlations between DAS waveforms and spectra with colocated seismometers, validating DAS data for detecting rockfall impacts. Fiber configuration impacted DAS sensitivity: fully in-contact cables improved signal-to-noise ratios and detection of high frequencies from 55 to 86 Hz. Analyses of seismic waves identified three distinct rock block propagation modes associated with intact, fragmenting, and collapse-triggering movements. While DAS signal feature values agreed with seismometers, no clear mass correlation emerged within the examined range. However, spectral features like frequency centroid (48.8 ± 6.5 Hz) and predominant frequency (41.0 ± 12.1 Hz) exhibited spatial stability across channels, indicating potential for event identification. Preliminary attempts to locate rockfall sources from DAS arrays proved feasible but require optimization. Overall, enhanced fiber coupling, identification of propagation modes, spatially-dependent analyses, and dense-array source location may enable DAS to complement sparse seismic networks for higher resolution, cost-effective rockfall monitoring. These insights could inform the development of improved rockfall monitoring strategies leveraging distributed fiber-optic sensing.

Design and Experimental Analysis of an Optical Fiber Coupling System for a Ground-based Telescope with Adaptive Optics

Astronomy photonics has opened up a new era for the application of astronomical optical instruments. The fiber coupling system serves as the crucial link between the telescope and photonic devices. This paper explores a beam shaping method that utilizes a coupled lens to enhance the efficiency of coupling light into an optical single mode fiber. Compared to directly coupling the telescope beam into the fiber, this approach offers improved coupling efficiency and greater adjustment tolerance. The laboratory-based optical fiber coupling system described in this study comprises an imaging component with an F/50 ratio and a fiber coupling component. Theoretical analysis indicates that optimal coupling efficiency is achieved when the diameter of the focusing spot, limited by diffraction, matches the fiber core size. Any axial error, position error, or tip-tilt error between the lens and the fiber will reduce the coupling efficiency. Experimental results confirm that the coupling system achieves an efficiency of approximately 70%, which is close to the theoretical limit of 78%. These findings underscore the effectiveness of the fiber coupling method.

3D Printing of Low-Filled Basalt PA12 and PP Filaments for Automotive Components

Fused Deposition Modeling (FDM) enables many advantages compared to traditional manufacturing techniques, but the lower mechanical performance due to the higher porosity still hinders its industrial spread in key sectors like the automotive industry. PP and PA12 filaments filled with low amounts of basalt fibers were produced in the present work to improve the poor mechanical properties inherited from the additive manufacturing technique. For both matrices, the introduction of 5 wt.% of basalt fibers allows us to achieve stiffness values comparable to injection molding ones without modifying the final weight of the manufactured components. The increased filament density compared with the neat polymers, upon the introduction of basalt fibers, is counterbalanced by the intrinsic porosity of the manufacturing technique. In particular, the final components are characterized by a 0.88 g/cm3 density for PP and 1.01 g/cm3 for PA12 basalt-filled composites, which are comparable to the 0.91 g/cm3 and 1.01 g/cm3, respectively, of the related neat matrix used in injection molding. Some efforts are still needed to fill the gap of 15–28% for PP and of 26.5% for PA12 in tensile strength compared to injection-molded counterparts, but the improvement of the fiber/matrix interface by fiber surface modification or coupling agent employment could be a feasible solution.

A Magnetic Field Sensor Based on Directional Coupling in a Magnetic Fluid-Filled Photonic Crystal Fiber.

In this paper, a dual-core photonic crystal fiber (DC-PCF) sensitivity sensor filled with magnetic liquid is introduced and investigated with the finite element method (FEM). To regulate the energy coupling involving the two cores, the magnetic fluid is filled into the pore between the two cores. To adjust the coupling between the supermodes in the DC-PCF, the refractive index (RI) of the air hole filled magnetic fluid may change due to the external magnetic field. This specifically created a magnetic fluid-filled DC-PCF; the magnetic fluid-filled hole is not used as the core for energy transmission, thus avoiding transmission loss. The dip wavelength and the magnetic field displayed an excellent linear connection between 80 and 260 Oe, depending on the numerical data. The detection sensitivity of the magnetic field reached 515.75 pm/Oe at a short fiber length of 482 µm. The designed magnetic fluid-filled DC-PCF has high sensitivity and small volume and has great application prospects in magnetic field detection in the medical and industrial fields.

Ultra-broadband 3-dB coupler based on dual-hollow-core polymer fiber covering E + S + C + L + U band.

An ultra-broadband 3-dB coupler based on a polymer dual-hollow-core anti-resonant fiber (DHC-ARF) is designed to work in the E + S + C + L + U communication band. By incorporating two elliptical-like cores and modulating the air gap between the two cores, the wavelength and polarization dependence of the DHC-ARF-based coupler is reduced effectively. The feasibility of using a 1.46 cm long DHC-ARF as the ultra-broadband coupler for the operating bandwidth of 400 nm in the range between 1.33 µm and 1.73 µm is demonstrated theoretically. The coupling ratio of each polarized mode stabilizes at 50 ± 2% and the coupling ratio difference between the two polarized modes changes within ±0.6%. This DHC-ARF coupler which is made of a polymer can be fabricated by high-resolution 3D printing. Compared to a silica-based DHC-ARF coupler, the polymer-based DHC-ARF coupler is easier to manufacture and the total loss of the latter is only 0.041 ± 0.006 dB in the operating bandwidth. The polymer hollow-core fiber coupler boasting an ultra-broadband, short component length, and low loss is very promising in next-generation, high-speed, and large-capacity hollow-core fiber communication systems.

Fiber Coupled High Power Nd:YAG Laser for Nondestructive Laser Cleaning

In this study, a fiber coupled high power side-pumped Nd:YAG laser system for laser cleaning is presented. Based on the two-rod structure and two stages amplifiers, the maximum average output power of 783 W with corresponding pulse energy of 52 mJ at 15 kHz has been achieved. The fiber coupling efficiencies after the master oscillator, one stage amplifier and two stages amplifiers reach to 99%, 98.3% and 94%, respectively. A laser cleaning machine prototype composed of the master oscillator and one stage amplifier with an average output power of greater than 500 W has been developed and achieved better nondestructive cleaning effect for thermal control coating removal compared with commercial fiber laser cleaning machines. This study provides a new method for developing high power laser sources for nondestructive laser cleaning equipment.

Design of New Photonic Crystal Fiber for Orbital Angular Momentum Modes Transmission

In order to achieve the flexibility and miniaturization of orbital angular momentum (OAM) fiber coupler, it is necessary to continuously design and optimize the base fiber to cooperate with the efficient transmission of multiplexed beam. It is more advantageous to use the photonic crystal fiber (PCF) instead of ring fiber in the coupler design. We have proposed a new fiber based on circular PCF structure to support high performance OAM modes transmission. The optimal parameters are selected to realize the stable transmission of 4 OAM mode groups with high mode quality. In the wavelength range of 1.2 μm∼2.0 μm, the confinement loss of low order mode is less than 10−8 dB/m, and the mode purity is more than 81.7%. Because of its flexible structure and low loss characteristics, the proposed OAM fiber can be widely used in the design of optical fiber devices in modular division multiplexing (MDM) communication systems.

Asymmetric Curvature Side-Polished Optical Fiber Coupler

Asymmetric Curvature Side-Polished Optical Fiber Coupler

Single-mode optical fiber couplers made of fluoride glass.

We demonstrate the first single-mode optical fiber couplers made with ZBLAN optical fiber. Couplers are fabricated using a controlled tapering procedure enabling high reproducibility while limiting glass crystallization. A coupling ratio of up to 41%/59% in cross/through ports with an excess loss of 2.5 dB is obtained at a wavelength of 2.73 μm. In addition, the stability of a coupler with traces of surface crystallization is tested at ambient atmosphere over a period of more than 90 days.

High-sensitivity liquid level sensor based on single mode-coreless-seven core-coreless-single mode fiber structure

A liquid level sensor based on single mode-coreless-seven core-coreless-single mode fiber structure is proposed, in which two short sections of coreless fibers are utilized as fiber couplers, so as to improve the coupling efficiency between the single mode fiber and the seven core fiber, thus enhance the mode interference perception of external liquid level. Experimental results reveal that the liquid level sensitivities of the sensors with seven core fiber length of 16 mm, 18 mm and 20 mm, are −0. 3163 nm/mm, −0.2687 nm/mm and −0.2471 nm/mm in the liquid level ranges of 16 mm, 18 mm and 20 mm, respectively. In addition, stability test is performed and the maximum instability is 0.04 nm with a standard error of 0.16 mm. The sensor possesses advantages of robustness, low fabrication cost, high sensitivity and good stability, indicating it has a prospective potential in petrochemical and biological applications for liquid level sensing.

Highly Enhanced Mechanical, Thermal, and Crystallization Performance of PLA/PBS Composite by Glass Fiber Coupling Agent Modification.

To improve the toughness and heat resistance of polylactic acid (PLA), polybutylene succinate (PBS) was sufficiently blended with PLA as the base matrix, and the glass fiber (GF) that was modified with 3-aminopropyltriethoxysilane (KF-GF) was added as the reinforcement. The results demonstrated a noteworthy boost in both mechanical and heat resistance properties when employing KH-GF, in comparison to pristine GF. When the content of KH-GF reached 20%, the tensile, flexural, and IZOD impact strength of the composites were 65.53 MPa, 83.43 MPa, and 7.45 kJ/m2, respectively, which were improved by 123%, 107%, and 189% compared to the base matrix, respectively. This enhancement was primarily attributed to the stronger interfacial adhesion between KH-GF and the PLA/PBS matrix. Furthermore, the Vicat softening temperature of the composites reached 128.7 °C, which was a result of increased crystallinity. In summary, the incorporation of KH-GF into PLA/PBS composites resulted in notable enhancements in their mechanical properties, crystallinity, and thermal characteristics. The high performance KH-GF-reinforced PLA/PBS composite showed a broad application potential in the field of biodegradable packaging, biodegradable textiles, and biodegradable plastic bags.

Fabrication of waveguide directional couplers using 2-photon lithography.

Advances in 2-photon lithography have enabled in-lab production of sub-micron resolution and millimeter scale 3D optical components. The potential complex geometries are well suited to rapid prototyping and production of waveguide structures, interconnects, and waveguide directional couplers, furthering future development and miniaturization of waveguide-based imaging technologies. System alignment is inherent to the 2-photon process, obviating the need for manual assembly and allowing precise micron scale waveguide geometries not possible in traditional fused fiber coupler fabrication. Here we present the use of 2-photon lithography for direct printing of multi-mode waveguide couplers with air cladding and single mode waveguide couplers with uncured liquid photoresin cladding. Experimental results show reproducible coupling which can be modified by selected design parameters.

An Integrated Magnetometer Module With MFCs Based on Diamond NV Centers

In recent years, nitrogen vacancy (NV) centers in diamond have become a promising solid-state magnetic sensor for applications due to their high sensitivity to magnetic field and excellent spatial resolution at room temperature. However, diamond magnetometer has complex and large optical system and microwave system, it is necessary to address the requirements of the measured environment for the small space and high sensitivity of the magnetometer in practical applications. In this paper, we propose an integrated magnetometer module with magnetic flux concentrators (MFCs) shaped like the wings of an airplane. The fiber coupler, diamond, microwave antenna, filters, photodetector and a weak signal processing circuit are integrated in the integrated module. MFCs are also integrated to collect flux from a larger area and concentrate it into the center of diamond magnetometer, which are used to improve the sensitivity of the diamond magnetometer. The volume of the integrated module is limited to 3.81 cm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sup> and achieve the actual magnetic sensitivity of sub-0.34 nT/Hz <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1/2</sup> . In the designed magnetometer module, the devices are assembled more easily and tightly, which provides a new degree of freedom for the production of diamond magnetometer.