Fiber Bundles Research Articles

Revealing the failure mechanism of 2D triaxially braided composites under off-axial tension through mesoscale simulations

The external load angle is known to have a significant influence on the mechanical behavior of two-dimensional triaxially braided composites (2DTBCs). However, the experimental data for 2DTBCs under off-axial loading provide limited information for understanding the failure mechanisms. In this study, a comprehensive mesoscale finite element (FE) model for simulating 2DTBC specimens was established to evaluate the mechanical responses and damage characteristics when off-axial tensile loads are applied. The FE model effectively captured the mechanical response at five distinct angles (0°, 30°, 45°, 60°, and 90°) and revealed the evolving patterns of failure behavior, damage morphology, and out-of-plane deformation mechanisms corresponding to the different loading angles. The findings indicate that, when the external load aligns with the axial fiber bundle direction, the primary failure mechanism involves the fracture of load-bearing fiber bundles. In contrast, deviations from the axial loading direction resulted in failure that was primarily due to the undulation of the bias fiber bundles, resulting in a loading angle–dependent warping at the edge of the specimen due to local shear stress concentration. The findings of this study provide valuable insights that can inform the design of structures with improved application.

Chinese expert consensus on surgical treatment of hypertensive intracerebral hemorrhage based on parafascicular approach(2024 edition)

Hypertensive intracerebral hemorrhage (HICH) is one of the main causes of death and disability in Chinese people. Surgical treatment can reduce the mortality rate of patients with HICH, but cannot improve functional prognosis. Therefore, promoting the neurological function recovery of surviving patients has become the focus of treatment for HICH. The corticospinal tract (CST) is the main descending fiber bundle that maintains motor function, and its integrity determines the degree of motor function recovery. Therefore, reducing CST injury is expected to improve motor dysfunction in patients with supratentorial deep HICH. Standardizing the indications, surgical strategies, and operational procedures for minimally invasive surgical treatment via the parafascicular approach can achieve maximum hematoma clearance and minimal white fiber bundle damage, which is beneficial for promoting the recovery of white matter fibers and improving neurological function prognosis. The Chinese Congress of Neurological Surgeons of Chinese Medical Doctor Association, the Neurosurgery Branch of the Chinese Medical Association, the Intracerebral Hemorrhage Minimally Invasive Surgical Treatment Branch of the Chinese Stroke Association, and the Stroke Branch of the Chongqing Medical Association organized relevant domestic experts to systematically query and evaluate existing relevant research evidence, refer to relevant international consensus and guidelines, and combine national conditions and domestic needs. A total of 31 recommendations were formed for preoperative examination, surgical indications, intraoperative positioning, surgical methods, hemostasis techniques, and perioperative management for surgical treatment of HICH based on white matter fiber protection, hoping to provide important reference for the surgical treatment of HICH.

Characterization of a conductive hydrogel@Carbon fibers electrode as a novel intraneural interface

Peripheral neural interfaces facilitate bidirectional communication between the nervous system and external devices, enabling precise control for prosthetic limbs, sensory feedback systems, and therapeutic interventions in the field of Bioelectronic Medicine. Intraneural interfaces hold great promise since they ensure high selectivity in communicating only with the desired nerve fascicles. Despite significant advancements, challenges such as chronic immune response, signal degradation over time, and lack of long-term biocompatibility remain critical considerations in the development of such devices. Here we report on the development and benchtop characterization of a novel design of an intraneural interface based on carbon fiber bundles. Carbon fibers possess low impedance, enabling enhanced signal detection and stimulation efficacy compared to traditional metal electrodes. We provided a 3D-stabilizing structure for the carbon fiber bundles made of PEDOT:PSS hydrogel, to enhance the biocompatibility between the carbon fibers and the nervous tissue. We further coated the overall bundles with a thin layer of elastomeric material to provide electrical insulation. Taken together, our results demonstrated that our electrode possesses adequate structural and electrochemical properties to ensure proper stimulation and recording of peripheral nerve fibers and a biocompatible interface with the nervous tissue.

Role of intra-lamellar collagen and hyaluronan nanostructures in annulus fibrosus on lumbar spine biomechanics: insights from molecular mechanics-finite element-based multiscale analyses.

Annulus fibrosus' (AF) ability to transmit multi-directional spinal motion is contributed by a combination of chemical interactions among biomolecular constituents-collagen type I (COL-I), collagen type II (COL-II), and proteoglycans (aggrecan and hyaluronan)-and mechanical interactions at multiple length scales. However, the mechanistic role of such interactions on spinal motion is unclear. The present work employs a molecular mechanics-finite element (FE) multiscale approach to investigate the mechanistic role of molecular-scale collagen and hyaluronan nanostructures in AF, on spinal motion. For this, an FE model of the lumbar segment is developed wherein a multiscale model of AF collagen fiber, developed from COL-I, COL-II, and hyaluronan using the molecular dynamics-cohesive finite element multiscale method, is incorporated. Analyses show AF collagen fibers primarily contribute to axial rotation (AR) motion, owing to angle-ply orientation. Maximum fiber strain values of 2.45% in AR, observed at the outer annulus, are 25% lower than the reported values. This indicates native collagen fibers are softer, attributed to the softer non-fibrillar matrix and higher interfibrillar sliding. Additionally, elastic zone stiffness of 8.61 Nm/° is observed to be 20% higher than the reported range, suggesting native AF lamellae exhibit lower stiffness, resulting from inter-collagen fiber bundle sliding. The presented study has further implications towards the hierarchy-driven designing of AF-substitute materials.

Critical crack length during fracture.

Through controlled numerical simulations in a one-dimensional fiber bundle model with local stress concentration, we established an inverse correlation between the strength of the material and the cracks which grow inside it-both the maximum crack and the one that sets in instability within the system, defined to be the critical crack. Through the Pearson correlation function as well as probabilistic study of individual configurations, we found that the maximum and the critical crack often differ from each other unless the disorder strength is extremely low. A phase diagram on the plane of disorder vs system size demarcates between the regions where the largest crack is the most vulnerable one and where they differ from each other but still show moderate correlation.

A Novel Biomineralized Collagen Liquid Crystal Hydrogel Possessing Bone-like Nanostructures by Complete In Vitro Fabrication.

The microstructure of bone consists of nano-hydroxyapatite (nano-HA) crystals aligned within the interspaces of collagen fibrils. To emulate this unique microstructure of bone, this work applied two biomimetic techniques to obtain bone-like microstructures in vitro, that is, combining the construction of collagen liquid crystal hydrogel (CLCH) with the application of a polymer-induced liquid precursor (PILP) mineralization process. Upon the elevation of pH, the collagen macromolecules within the collagen liquid crystal (CLC) were activated to self-assemble into CLCH, whose fibrils packed into a long and dense fiber bundle in high orientation, emulating the dense-packed matrix of bone. We demonstrated that the fibrillar mineralization of CLCH, leading to a bone-like nanostructured inorganic material part, can be achieved using the PILP crystallization process to pre-mineralize the dense collagen substrates of CLCH with CaCO3, immediately followed by the in situ mineral phase transformation of CaCO3 into weak-crystalline nano-HA. The combination of CLCH with the biomineralization process of PILP, together with the mineral phase transformation, achieved the in vitro simulation of the nanostructures of both the organic extracellular matrix (ECM) and inorganic ECM of bone. This design would constitute a novel idea for the design of three-dimension biomimetic bone-like material blocks for clinical needs.

Laser Doppler velocimetry based on multi-core fiber

Fiber laser doppler velocimetry has the advantages of high measurement accuracy, wide measurement range and non-contact measurement. Usually, fiber optic bundles are used in traditional measurement systems. Multi-core fiber (MCF) is a new structure of optical fiber with multiple cores in the same cladding and a uniform core layout. Compared to traditional fiber bundles, multi-core fibers have advantages in integration and volume. Therefore, by taking advantage of the special spatial arrangement of cores and compact structure of MCF, we investigate the laser doppler velocimetry system. The main work includes:1. Simulation and analysis of double-beam interference fringes based on MCF; 2. Construct a laser doppler velocimetry system based on MCF, and verify the feasibility of the experimental system. Our method provides an effective solution for fiber laser doppler velocimetry.

Are the Hypo-Reflective Clumps Associated With Age-Related Macular Degeneration in Adaptive Optics Ophthalmoscopy Autofluorescent?

Hypo-reflective clumps (HRCs) are structures associated with age-related macular degeneration (AMD) that were identified using flood-illumination adaptive optics ophthalmoscopy (FIAO) and hypothesized to be either macrophages that have accumulated melanin through the phagocytosis of retinal pigmented epithelial (RPE) cell organelles or transdifferentiated RPE cells. HRCs may be autofluorescent (AF) in the near infrared (NIR) but clinical NIR autofluorescence imaging lacks the resolution to answer this question definitively. Here, we used near infrared autofluorescence (NIRAF) imaging in fluorescence adaptive optics scanning laser ophthalmoscopy (AOSLO) to determine whether HRCs are AF. Patients with AMD and HRCs underwent imaging with FIAO, optical coherence tomography (OCT), and multi-modal AOSLO (confocal, NIRAF, and non-confocal multi-offset detection using a fiber bundle). HRCs were segmented on FIAO and images, co-registered across modalities, and HRC morphometry and AF were quantified. Eight patients participated (mean age = 79 years, standard deviation [SD] = 5.7, range = 69-89 years, and 5 female patients). Most HRCs (86%, n = 153/178) were autofluorescent on AOSLO. HRC AF signal varied but most uniformly dark HRCs on FIAO showed corresponding AF on AOSLO, whereas heterogeneous HRCs showed a smaller AF area or no AF. These findings are consistent with the hypothesis that HRCs contain AF RPE organelles. A small proportion of HRCs were not AF; these may represent macrophages that have not yet accumulated enough organelles to become AF. HRCs may have clinical significance but further study is needed to understand the interplay among HRCs, RPE cells, and macrophages, and their relationship to geographic atrophy (GA) progression in AMD.

Effect of Helix aspersa Mucus on the Regeneration of Skin with Photoaging Features in Different Methods of Application

Skin aging is associated with both intrinsic and extrinsic aging, with extrinsic aging caused by environmental factors and overlaying the effects of chronological aging. The main aim of this study was to evaluate the effect of preparations containing Helix aspersa snail mucus on skin regeneration with photoaging features. Before and 3 months after the series of treatments, skin biopsy specimens from the right preauricular region of the face were taken from six women. Histological, morphometric, and immunohistochemical analyses were performed. Positive changes, indicating a reduction in photoaging related to the reduction in epidermis thickness 3 months after the end of the treatments, were noted in each group. A statistically significant increase in the thickness of the collagen fiber bundles was also observed in the patients 3 months after a series of micro-needle mesotherapy treatments with snail mucus and 0.9% NaCl. There was a significant increase in the immuno-expression of Ki-67 and PCNA in the dermis. The aforementioned significance applies to patients in whom snail mucus was introduced with the use of micro-needle mesotherapy and needle-free mesotherapy. Moreover, a statistically significant increased area with the immunoexpression of MMP-2 in the dermis was observed in the above-mentioned groups of patients, who were treated with the preparation containing snail filtrate. The results of the study suggest that the use of snail mucus preparations for skincare, as well as its introduction by micro-needle and needleless mesotherapy, had a beneficial effect on the condition of the skin.

A human brain atlas of χ-separation for normative iron and myelin distributions.

Iron and myelin are primary susceptibility sources in the human brain. These substances are essential for a healthy brain, and their abnormalities are often related to various neurological disorders. Recently, an advanced susceptibility mapping technique, which is referred to as χ-separation (pronounced as "chi"-separation), has been proposed, successfully disentangling paramagnetic iron from diamagnetic myelin. This method provided a new opportunity for generating high-resolution iron and myelin maps of the brain. Utilizing this technique, this study constructs a normative χ-separation atlas from 106 healthy human brains. The resulting atlas provides detailed anatomical structures associated with the distributions of iron and myelin, clearly delineating subcortical nuclei, thalamic nuclei, and white matter fiber bundles. Additionally, susceptibility values in a number of regions of interest are reported along with age-dependent changes. This atlas may have direct applications such as localization of subcortical structures for deep brain stimulation or high-intensity focused ultrasound and also serve as a valuable resource for future research.

Damage mechanism and bending properties degradation of aviation composite honeycomb sandwich structures under laser irradiation

Damage mechanism and bending properties degradation of aviation composite honeycomb sandwich structures are studied under different laser conditions in this paper. Firstly, the damage test of composite honeycomb sandwich structures is conducted. Temperature field and ablation process during laser irradiation are analyzed. Damage morphology and mechanism are verified. Secondly, the influence of laser damage on the bending properties of composite honeycomb panels is studied. Progressive damage process and failure mechanism of honeycomb structures during loading are explored by digital image correlation (DIC) and strain trend. The results show that the temperature at the center point of front surface reaches more than 2000 °C within 1 s under the laser irradiation, while the temperature of back surface exhibits hysteresis. The ablation hole is funnel-shaped and has severe delamination. In the heat affected zone (HAZ), resin matrix has been basically sublimated and oxidized, leaving only carbon fiber bundles and some residual carbon. The honeycomb core in this area has been completely carbonized and deformed. During bending process, the honeycomb core breaks firstly, and strain appears peak at both crack ends, leading the crack extend along both sides. The ultimate load of damaged specimen is 2.35kN, which has a 42.26 % drop compared to that of healthy specimen 4.07kN. Bending properties of specimen are significantly degraded by laser damage.

Multi-Tissue Integrated Tissue-Engineered Trachea Regeneration Based on 3D Printed Bioelastomer Scaffolds.

Functional segmental trachea reconstruction is a critical concern in thoracic surgery, and tissue-engineered trachea (TET) holds promise as a potential solution. However, current TET falls short in fully restoring physiological function due to the lack of the intricate multi-tissue structure found in natural trachea. In this research, a multi-tissue integrated tissue-engineered trachea (MI-TET) is successfully developed by orderly assembling various cells (chondrocytes, fibroblasts and epithelial cells) on 3D-printed PGS bioelastomer scaffolds. The MI-TET closely resembles the complex structures of natural trachea and achieves the integrated regeneration of four essential tracheal components: C-shaped cartilage ring, O-shaped vascularized fiber ring, axial fiber bundle, and airway epithelium. Overall, the MI-TET demonstrates highly similar multi-tissue structures and physiological functions to natural trachea, showing promise for future clinical advancements in functional TETs.

White matter structure and derived network properties are used to predict the progression from mild cognitive impairment of older adults to Alzheimer’s disease

ObjectiveTo identify white matter fiber injury and network changes that may lead to mild cognitive impairment (MCI) progression, then a joint model was constructed based on neuropsychological scales to predict high-risk individuals for Alzheimer's disease (AD) progression among older adults with MCI.MethodsA total of 173 MCI patients were included from the Alzheimer's Disease Neuroimaging Initiative(ADNI) database and randomly divided into training and testing cohorts. Forty-five progressed to AD during a 4-year follow-up period. Diffusion tensor imaging (DTI) techniques extracted relevant DTI quantitative features for each patient. In addition, brain networks were constructed based on white matter fiber bundles to extract network property features. Ensemble dimensionality reduction was applied to reduce both DTI quantitative features and network features from the training cohort, and machine learning algorithms were added to construct white matter signature. In addition, 52 patients from the National Alzheimer's Coordinating Center (NACC) database were used for external validation of white matter signature. A joint model was subsequently generated by combining with scale scores, and its performance was evaluated using data from the testing cohort.ResultsBased on multivariate logistic regression, clinical dementia rating and Alzheimer’s disease assessment scales (CDRS and ADAS, respectively) were selected as independent predictive factors. A joint model was constructed in combination with the white matter signature. The AUC, sensitivity, and specificity in the training cohort were 0.938, 0.937, and 0.91, respectively, and the AUC, sensitivity, and specificity in the test cohort were 0.905, 0.923, and 0.872, respectively. The Delong test showed a statistically significant difference between the joint model and CDRS or ADAS scores (P < 0.05), yet no significant difference between the joint model and the white matter signature (P = 0.341).ConclusionThe present results demonstrate that a joint model combining neuropsychological scales can be constructed by using machine learning and DTI technology to identify MCI patients who are at high-risk of progressing to AD.

Antibody to Endogenous Cardiotonic Steroid Reverses Vascular Fibrosis and Restores Vasorelaxation in Chronic Kidney Disease.

Marinobufagenin (MBG) is implicated in chronic kidney disease, where it removes Fli1-induced inhibition of the collagen-1. We hypothesized that (i) in nephrectomized rats, aortic fibrosis develops due to elevated plasma MBG and inhibited Fli1, and (ii) that the antibody to MBG reduces collagen-1 and improves vasodilatation. A partial nephrectomy was performed in male Sprague-Dawley rats. Sham-operated animals comprised the control group. At 5 weeks following nephrectomy, rats were administered the vehicle (n = 8), or the anti-MBG antibody (n = 8). Isolated aortic rings were tested for their responsiveness to sodium nitroprusside following endothelin-1-induced constriction. In nephrectomized rats, there was an increase in the intensity of collagen staining in the aortic wall vs. the controls. In antibody-treated rats, the structure of bundles of collagen fibers had ordered organization. Western blots of the aorta had lower levels of Fli1 (arbitrary units, 1 ± 0.05 vs. 0.2 ± 0.01; p < 0.001) and greater collagen-1 (arbitrary units, 1 ± 0.01 vs. 9 ± 0.4; p < 0.001) vs. the control group. Administration of the MBG antibody to rats reversed the effect of the nephrectomy on Fli1 and collagen-1 proteins. Aortic rings pretreated with endothelin-1 exhibited 50% relaxation following the addition of sodium nitroprusside (EC50 = 0.28 μmol/L). The responsiveness of the aortic rings obtained from nephrectomized rats was markedly reduced (EC50 = 3.5 mol/L) compared to the control rings. Treatment of rats with the antibody restored vasorelaxation. Thus, the anti-MBG antibody counteracts the Fli1-collagen-1 system and reduces aortic fibrosis.

Stability analysis of polynomials with an approach of differential topology

SummaryIn this paper, we study the Hurwitz stability of polynomials. By considering that a degree Hurwitz polynomial has its corresponding Markov parameters, we define the set in Section 3, we also define . Based on properties of the Hankel matrices and the stability test, as well as by using ideas of differential topology, we show that is a fiber bundle with a base. This result allows us to obtain an interesting application: Given a Hurwitz polynomial, we can generate two families of positive definite Hankel matrices.

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

AbstractThis study investigates the influence of a combined thermal heat flux (imposed by a cone calorimeter) and a compressive loading on the deformation and damage mechanisms within quasi‐isotropic carbon fibers reinforced thermoplastic (polyetherether ketone [PEEK] and polyphenylene sulfide [PPS]) and thermosetting (epoxy) laminates. First, thermogravimetric Analyses conducted under nitrogen provide valuable information on the thermal decomposition of these materials depending on the matrix nature (580–510°C and 350°C, respectively) which is a key factor to explain the mechanical behavior under fire conditions. Second, under the same testing conditions (creep loading under a 50 kW/m2 heat flux), the time to failure is about 17 times as high (C/PEEK), twice as high (C/PPS) with respect to C/epoxy laminates. At the ply scale, the exposure of thermoplastic matrices (PEEK and PPS) to a 50 kW/m2 heat flux causes softening and thermal decomposition, facilitating the micro‐buckling of fiber bundles in matrix‐rich areas. At the laminates scale, this mechanism ultimately leads to the formation and propagation of plastic kink bands in the transverse direction. In epoxy‐based laminates, the onset of matrix pyrolysis occurs at lower temperatures (350°C) during thermal aggression, and thermal decomposition has started in all the plies of the laminates. Combined with the low ductility of the epoxy matrix, the compressive response is elastic‐brittle and results from the buckling of 0° plies outside the thermally‐damaged area.Highlights Study on the compression of polymer composites exposed to a 50 kW/m2 heat flux. The influence of the matrix nature (thermoplastic vs thermoset) is discussed. Time to failure is about 17 times higher in C/PEEK compared to C/Epoxy. Plastic kink bands propagate in thermoplastic composites at T &gt; Tg. C/Epoxy laminates undergo buckling outside the thermally damaged area.

Methodological considerations on diffusion MRI tractography in infants aged 0-2 years: a scoping review.

Diffusion MRI (dMRI) enables studying the complex architectural organization of the brain's white matter (WM) through virtual reconstruction of WM fiber tracts (tractography). Despite the anticipated clinical importance of applying tractography to study structural connectivity and tract development during the critical period of rapid infant brain maturation, detailed descriptions on how to approach tractography in young infants are limited. Over the past two decades, tractography from infant dMRI has mainly been applied in research settings and focused on diffusion tensor imaging (DTI). Only few studies used techniques superior to DTI in terms of disentangling information on the brain's organizational complexity, including crossing fibers. While more advanced techniques may enhance our understanding of the intricate processes of normal and abnormal brain development and extensive knowledge has been gained from application on adult scans, their applicability in infants has remained underexplored. This may partially be due to the higher technical requirements versus the need to limit scan time in young infants. We review various previously described methodological practices for tractography in the infant brain (0-2 years-of-age) and provide recommendations to optimize advanced tractography approaches to enable more accurate reconstructions of the brain WM's complexity. IMPACT: Diffusion tensor imaging is the technique most frequently used for fiber tracking in the developing infant brain but is limited in capability to disentangle the complex white matter organization. Advanced tractography techniques allow for reconstruction of crossing fiber bundles to better reflect the brain's complex organization. Yet, they pose practical and technical challenges in the fast developing young infant's brain. Methods on how to approach advanced tractography in the young infant's brain have hardly been described. Based on a literature review, recommendations are provided to optimize tractography for the developing infant brain, aiming to advance early diagnosis and neuroprotective strategies.

Enhanced strength and toughness of carbon fiber reinforced aluminum matrix composite prepared via novel indirect extrusion method

The fabrication of large-sized, high-performance CF/Al composites presents significant challenges for the aerospace industry. This study introduces a novel indirect extrusion (IE) method for the high-quality production of CF/Al composites. The study investigates the infiltration mechanism of the alloy liquid during the IE process, highlights the technique's advantages, and systematically analyzes the mechanical properties and failure mechanisms of CF/Al composites. Results show that the aluminum liquid initially fills the interlayers and subsequently penetrates the fiber bundles, effectively shortening the infiltration distance. At a casting temperature of 800°C and an infiltration pressure of 40 MPa, the composite exhibits excellent forming quality and microstructural integrity. Compared to direct extrusion (DE) CF/Al composites, IE-CF/Al composites show significant improvements in compressive strength (16.72 %), flexural strength (16.87 %), fracture toughness (43.18 %), and work of fracture (90.61 %). The interlayer alloy and increased fiber spacing in IE-CF/Al composites enhance energy absorption capacity and reduce the risk of brittle fracture. This process lays a solid foundation for the high-quality production and application of CF/Al composites.

Bundle-specific tractogram distribution estimation using higher-order streamline differential equation

Streamline tractography locally traces peak directions extracted from fiber orientation distribution (FOD) functions, lacking global information about the trend of the whole fiber bundle. Therefore, it is prone to producing erroneous tracks while missing true positive connections. In this work, we propose a new bundle-specific tractography (BST) method based on a bundle-specific tractogram distribution (BTD) function, which directly reconstructs the fiber trajectory from the start region to the termination region by incorporating the global information in the fiber bundle mask. A unified framework for any higher-order streamline differential equation is presented to describe the fiber bundles with disjoint streamlines defined based on the diffusion vectorial field. At the global level, the tractography process is simplified as the estimation of BTD coefficients by minimizing the energy optimization model, and is used to characterize the relations between BTD and diffusion tensor vector under the prior guidance by introducing the tractogram bundle information to provide anatomic priors. Experiments are performed on simulated Hough, Sine, Circle data, ISMRM 2015 Tractography Challenge data, FiberCup data, and in vivo data from the Human Connectome Project (HCP) for qualitative and quantitative evaluation. Results demonstrate that our approach reconstructs complex fiber geometry more accurately. BTD reduces the error deviation and accumulation at the local level and shows better results in reconstructing long-range, twisting, and large fanning tracts.

Continuous glass fiber‐reinforced polycaprolactone composite produced in a conventional fused filament fabrication equipment: Process modeling and parameters adjustment

AbstractPolymer composites with continuous fibers are expected to exhibit good mechanical performance due to orientation and high aspect ratio of fillers. Fused filament fabrication (FFF) provides an affordable method for processing these materials as products with tunable architecture. By incorporating continuous bioactive fibers coated with biodegradable polymer, the degradation rate of printed scaffolds may vary over time. As proof of concept, macroporous composites were 3D printed using continuous glass fiber‐reinforced polycaprolactone filament. Parametrization and challenges associated with printing on non‐dedicated equipment are discussed. A model describing the melt flow was employed to evaluate the velocity and shear rate profiles. Although the maximum velocity is approximately 18 mm s−1 for both neat and reinforced polymer, the obstruction caused by fibers results in higher shear rate, up to 481 s−1, higher pressure gradient, 1.95 MPa mm−1, and higher velocity gradient, conditions that limit print quality. Additionally, it was also possible to determine the shear stress experienced by the fiber bundle, 300 KPa, and the influence of different processing conditions. This investigation advances the development and understanding of manufacturing of continuous fiber‐reinforced polymers via FFF.