Extreme-ultraviolet Wave Front Research Articles

Tracking the motion of a shock along a channel in the low solar corona

Context. Shock waves are excited by coronal mass ejections (CMEs) and large-scale extreme-ultraviolet (EUV) wave fronts and can result in low-frequency radio emission under certain coronal conditions. Aims. In this work, we investigate a moving source of low-frequency radio emission as a CME and an associated EUV wave front move along a channel of a lower density, magnetic field, and Alfvén speed in the solar corona. Methods. Observations from the Atmospheric Imaging Assembly on board the Solar Dynamics Observatory, the Nançay Radio Heliograph (NRH), and the Irish Low Frequency Array (I-LOFAR) were analysed. Differential emission measure maps were generated to determine densities and Alfvén maps, and the kinematics of the EUV wave front was tracked using CorPITA. The radio sources’ positions and velocity were calculated from NRH images and I-LOFAR dynamic spectra. Results. The EUV wave expanded radially with a uniform velocity of ∼500 km s−1. However, the radio source was observed to be deflected and appeared to move along a channel of a lower Alfvén speed, abruptly slowing from 1700 km s−1 to 250 km s−1 as it entered a quiet-Sun region. A shock wave with an apparent radial velocity of > 420 km s−1 was determined from the drift rate of the associated Type II radio burst. Conclusions. The apparent motion of the radio source may have resulted from a wave front moving along a coronal wave guide or by different points along the wave front emitting at locations with favourable conditions for shock formation.

Direct imaging of magnetohydrodynamic wave mode conversion near a 3D null point on the sun

Mutual conversion of various kinds of magnetohydrodynamic (MHD) waves can have profound impacts on wave propagation, energy transfer, and heating of the solar chromosphere and corona. Mode conversion occurs when an MHD wave travels through a region where the Alfvén and sound speeds are equal (e.g., a 3D magnetic null point). Here we report the direct extreme ultraviolet (EUV) imaging of mode conversion from a fast-mode to a slow-mode MHD wave near a 3D null point using Solar Dynamics Observatory/Atmospheric Imaging Assembly (SDO/AIA) observations. An incident fast EUV wavefront associated with an adjacent eruptive flare propagates laterally through a neighboring pseudostreamer. Shortly after the passage of the fast EUV wave through the null point, a slow-mode wave appears near the null that propagates upward along the open structures and simultaneously downward along the separatrix encompassing the fan loops of the pseudostreamer base. These observations suggest the existence of mode conversion near 3D nulls in the solar corona, as predicted by theory and MHD simulations. Moreover, we observe decaying transverse oscillations in both the open and closed structures of the pseudostreamer, along with quasiperiodic type III radio bursts indicative of repetitive episodes of electron acceleration.

Simultaneous Horizontal and Vertical Oscillation of a Quiescent Filament Observed by CHASE and SDO

In this paper, we present the imaging and spectroscopic observations of the simultaneous horizontal and vertical large-amplitude oscillation of a quiescent filament triggered by an extreme-ultraviolet (EUV) wave on 2022 October 2. Particularly, the filament oscillation involved winking phenomenon in Hα images and horizontal motions in EUV images. Originally, a filament and its overlying loops across AR 13110 and 13113 erupted with a highly inclined direction, resulting in an X1.0 flare and a non-radial coronal mass ejection. The fast lateral expansion of loops excited an EUV wave and the corresponding Moreton wave propagating northward. Once the EUV wave front arrived at the quiescent filament, the filament began to oscillate coherently along the horizontal direction, and the “winking filament” appeared concurrently in Hα images. The horizontal oscillation involved an initial amplitude of ∼10.2 Mm and a velocity amplitude of ∼46.5 km s−1, lasting for ∼3 cycles with a period of ∼18.2 minutes and a damping time of ∼31.1 minutes. The maximum Doppler velocities of the oscillating filament are 18 km s−1 (redshift) and −24 km s−1 (blueshift), which were derived from the spectroscopic data provided by the Chinese Hα Solar Explorer/Hα Imaging Spectrograph. The three-dimensional velocity of the oscillation is determined to be ∼50 km s−1 at an angle of ∼50° to the local photosphere plane. Based on the wave–filament interaction, the minimum energy of the EUV wave is estimated to be 2.7 × 1020 J. Furthermore, this event provides evidence that Moreton waves should be excited by the highly inclined eruptions.

Extreme-ultraviolet structured beams via high harmonic generation

Vigorous efforts to harness the topological properties of light have enabled a multitude of novel applications. Translating the applications of structured light to higher spatial and temporal resolutions mandates their controlled generation, manipulation, and thorough characterization in the short-wavelength regime. Here, we resort to high-order harmonic generation (HHG) in a noble gas to upconvert near-infrared (IR) vector, vortex, and vector-vortex driving beams that are tailored respectively in their Spin Angular Momentum (SAM), Orbital Angular Momentum (OAM), and simultaneously in their SAM and OAM. We show that HHG enables the controlled generation of extreme-ultraviolet (EUV) vector beams exhibiting various spatially-dependent polarization distributions, or EUV vortex beams with a highly twisted phase. Moreover, we demonstrate the generation of EUV vector-vortex beams (VVB) bearing combined characteristics of vector and vortex beams. We rely on EUV wavefront sensing to unambiguously affirm the topological charge scaling of the HHG beams with the harmonic order. Interestingly, our work shows that HHG allows for a synchronous controlled manipulation of SAM and OAM. These EUV structured beams bring in the promising scenario of their applications at nanometric spatial and sub-femtosecond temporal resolutions using a table-top harmonic source.

EUV and Hard X-ray Hartmann Wavefront Sensing for Optical Metrology, Alignment and Phase Imaging.

For more than 15 years, Imagine Optic have developed Extreme Ultra Violet (EUV) and X-ray Hartmann wavefront sensors for metrology and imaging applications. These sensors are compatible with a wide range of X-ray sources: from synchrotrons, Free Electron Lasers, laser-driven betatron and plasma-based EUV lasers to High Harmonic Generation. In this paper, we first describe the principle of a Hartmann sensor and give some key parameters to design a high-performance sensor. We also present different applications from metrology (for manual or automatic alignment of optics), to soft X-ray source optimization and X-ray imaging.

Mode Conversion of a Solar Extreme-ultraviolet Wave over a Coronal Cavity

Abstract We report on observations of an extreme-ultraviolet (EUV) wave event in the Sun on 2011 January 13 by Solar Terrestrial Relations Observatory and Solar Dynamics Observatory in quadrature. Both the trailing edge and the leading edge of the EUV wave front in the north direction are reliably traced, revealing generally compatible propagation velocities in both perspectives and a velocity ratio of about 1/3. When the wave front encounters a coronal cavity near the northern polar coronal hole, the trailing edge of the front stops while its leading edge just shows a small gap and extends over the cavity, meanwhile getting significantly decelerated but intensified. We propose that the trailing edge and the leading edge of the northward propagating wave front correspond to a non-wave coronal mass ejection component and a fast-mode magnetohydrodynamic wave component, respectively. The interaction of the fast-mode wave and the coronal cavity may involve a mode conversion process, through which part of the fast-mode wave is converted to a slow-mode wave that is trapped along the magnetic field lines. This scenario can reasonably account for the unusual behavior of the wave front over the coronal cavity.

A SOLAR TYPE II RADIO BURST FROM CORONAL MASS EJECTION-CORONAL RAY INTERACTION: SIMULTANEOUS RADIO AND EXTREME ULTRAVIOLET IMAGING

Simultaneous radio and extreme ultraviolet (EUV)/white-light imaging data are examined for a solar type II radio burst occurring on 2010 March 18 to deduce its source location. Using a bow-shock model, we reconstruct the 3-dimensional EUV wave front (presumably the type-II emitting shock) based on the imaging data of the two STEREO spacecraft. It is then combined with the Nan\c{c}ay radio imaging data to infer the 3-dimensional position of the type II source. It is found that the type II source coincides with the interface between the CME EUV wave front and a nearby coronal ray structure, providing evidence that the type II emission is physically related to the CME-ray interaction. This result, consistent with those of previous studies, is based on simultaneous radio and EUV imaging data for the first time.

UNDERSTANDINGSDO/AIA OBSERVATIONS OF THE 2010 JUNE 13 EUV WAVE EVENT: DIRECT INSIGHT FROM A GLOBAL THERMODYNAMIC MHD SIMULATION

In this work, we present a comprehensive observation and modeling analysis of the 2010 June 13 extreme-ultraviolet (EUV) wave observed by the Atmospheric Imaging Assembly (AIA) aboard the Solar Dynamics Observatory (SDO). Due to extreme advances in cadence, resolution, and bandpass coverage in the EUV regime, the AIA instrument offers an unprecedented ability to observe the dynamics of large-scale coronal wave-like transients known as EUV waves. To provide a physical analysis and further complement observational insight, we conduct a three-dimensional, time-dependent thermodynamic MHD simulation of the eruption and associated EUV wave, and employ forward modeling of EUV observables to compare the results directly observations. We focus on two main aspects: (1) the interpretation of the stark thermodynamic signatures in the multi-filter AIA data within the propagating EUV wave front, and (2) an in-depth analysis of the simulation results and their implication with respect to EUV wave theories. Multiple aspects, including the relative phases of perturbed variables, suggest that the outer, propagating component of the EUV transient exhibits the behavior of a fast-mode wave. We also find that this component becomes decoupled from the evolving structures associated with the coronal mass ejection that are also visible, providing a clear distinction between wave and non-wave mechanisms at play.

Testing extreme ultraviolet optics with visible-light and extreme ultraviolet interferometry

Optics for extreme ultraviolet (EUV) lithography arguably have the most strict fabrication tolerances of any optical systems fabricated to date, and the development of EUV lithography pushes advanced optical fabrication techniques toward never before realized levels of figure accuracy and finish quality. As EUV lithography advances toward viability, the need for ultrahigh-accuracy wave front metrology tools has never been greater. To enable the development of diffraction-limited EUV optical systems, visible-light and EUV interferometries must work in close collaboration. We present a detailed comparison of EUV and visible-light wave front measurements performed across the field of view of a lithographic-quality projection optical system designed for use in the Engineering Test Stand developed by the Virtual National Laboratory and the EUV Limited Liability Company. The comparisons reveal that the present level of root mean square agreement lies in the 0.3–0.4 nm range, with an agreement of 0.15±0.03 nm, excluding astigmatism. Astigmatism is the most significant aberration component for the alignment of this optical system; it is also the dominant term in the discrepancy, and the aberration with the highest measurement uncertainty. With EUV optical systems requiring total wave front quality in the λEUV/50 (0.25 nm) range, and even higher surface-figure quality for the individual mirror elements (∼0.1 nm), improved accuracy through future comparisons, and additional studies, are required.

Interferometry using undulator sources (invited, abstract)

Optical systems for extreme ultraviolet (EUV) lithography need to use optical components with subnanometer surface figure error tolerances to achieve diffraction-limited performance [M.D. Himel, in Soft X-Ray Projection Lithography, A.M. Hawryluk and R.H. Stulen, eds. (OSA, Washington, D.C., 1993), 18, 1089, and D. Attwood et al., Appl. Opt. 32, 7022 (1993)]. Also, multilayer-coated optics require at-wavelength wavefront measurement to characterize phase effects that cannot be measured by conventional optical interferometry. Furthermore, EUV optical systems will additionally require final testing and alignment at the operational wavelength for adjustment and reduction of the cumulative optical surface errors. Therefore, at-wavelength interferometric measurement of EUV optics will be the necessary metrology tool for the successful development of optics for EUV lithography. An EUV point diffraction interferometer (PDI) has been developed at the Center for X-Ray Optics (CXRO) and has been already in operation for a year [K. Goldberg et al., in Extreme Ultra Lithography, D.T. Attwood and F. Zernike, eds. (OSA, Washington, D.C., 1994), K. Goldberg et al., Proc. SPIE 2437, to be published, and K. Goldberg et al., J. Vac. Sci. Technol. B 13, 2923 (1995)] using an undulator radiation source and coherent optics beamline at the Advanced Light Source (ALS) at Lawrence Berkeley National Laboratory. An overview of the PDI interferometer and some EUV wavefront measurements obtained with this instrument will be presented. In addition, future developments planned for EUV interferometry at CXRO towards the measurement of actual EUV lithography optics will be shown.