External-cavity Laser Research Articles

PDM-SHD NFDM transmission with envelope-detection feedback polarization tracking and optical injection locking.

Nonlinear frequency division multiplexing (NFDM) systems, especially the eigenvalue communications have the potential to overcome the nonlinear Shannon capacity limit. However, the baud rate of eigenvalue communications is typically restricted to a few GBaud, making it challenging to mitigate laser frequency impairments such as the phase noise and frequency offset (FO) using digital signal processing (DSP) algorithms in intradyne detections (IDs). Therefore, we introduce the polarization division multiplexing-self-homodyne detection (PDM-SHD) into the NFDM link, which could overcome the impact of phase noise and FO by transmitting a pilot carrier originating from the transmitter laser to the receiver through the orthogonal polarization state of signal. To separate the signal from the carrier at the receiver, a carrier to signal power ratio (CSPR) unrestricted adaptive polarization controlling strategy is proposed and implemented by exploiting the optical intensity fluctuation of the light in a particular polarization rather than its direct optical power as the feedback. Optical injection locking (OIL) is used subsequently to amplify optical power of pilot carrier and mitigate the impact of signal-signal beat interference (SSBI). Additionally, the effects of cross-polarization modulation (XPolM) and modulation instability (MI) in long haul transmission are explored and inhibited. The results show that the tolerable FO range is about 3.5 GHz, which is 17 times larger than the ID one. When 16-amplitude phase shift keying (APSK) or 64-APSK constellations are used, identical Q-factor performance can be obtained by using distributed feedback (DFB, ∼10 MHz) laser, external cavity laser (ECL, ∼100kHz), or fiber laser (FL, ∼100 Hz), respectively, which demonstrates that our proposed PDM-SHD eigenvalue communication structure is insensitive to the laser linewidth. Under the impact of cycle slip, the Q-factor difference of 16-APSK signal between the ECL-ID system and ECL-SHD system can be up to 8.73 dB after 1500 km transmission.

Improved two-mode dynamic model for external-cavity quantum cascade lasers under strong optical feedback

In this paper, we propose an improved model for describing the dynamical behavior and mode selection mechanism of an external-cavity quantum-cascade laser (EC-QCL) when subject to strong optical feedback. Theoretical analysis including the dynamical effective reflectivity model, two-mode rate-equation model and Lang-Kobayashi equations are employed to carry out the laser output characteristics under the multiple feedback effects. A main aspect of the model is that the excess mirror loss caused by the EC effective reflectivity is incorporated into the laser dynamical equations as a nonlinear dynamical variable. Because of accounting the multiple round-trip feedback terms in the EC effective reflectivity, the analysis is valid for the arbitrary feedback regimes from weak to strong levels. Besides the stationary characteristics, the model accurately predicts the dynamical competition between the fundamental laser-cavity mode and the desired EC mode that reflected strongly by external diffraction grating. The results are in well agreement with theoretical and experimental data reported earlier for the EC-QCLs.

Single-carrier 800-Gb/s self-homodyne coherent transmission of DP-16QAM, DP-32QAM, and DP-64QAM with uncooled DFB laser.

Self-homodyne detection (SHD) is a promising approach to realize high-capacity short-reach optical transmission systems with low cost and low power consumption. We experimentally demonstrate single-carrier net 800-Gb/s SHD transmission with low-cost ∼MHz linewidth distributed feedback (DFB) laser over 2 km, 10 km, 25 km, and 40 km single-mode fiber (SMF) using three different quadrature amplitude modulation (QAM) formats, including 80-Gbaud dual-polarization (DP) 64QAM, 100-Gbaud DP-32QAM, and 120-Gbaud DP-16QAM. Among them, net 800-Gb/s DP-64QAM SHD transmission over 25 km SMF using an uncooled DFB laser with a linewidth of 2.6 MHz is experimentally verified. The detailed experimental performance evaluation of net 800Gb/s SHD system is performed, in which various configurations are considered, such as different laser linewidths, three QAM formats, and different transmission distances. DFB lasers with linewidths of 1 MHz and 2.6 MHz lead to negligible penalty when compared to the same SHD system but using an external cavity laser (ECL) with a linewidth of 26kHz in back-to-back (BTB) case. 80-Gbaud DP-64QAM obtains the highest optical signal-to-noise ratio (OSNR) requirement and the highest bit-error rate (BER) floor but the best tolerance of chromatic dispersion (CD). 120-Gbaud DP-16QAM achieves the lowest OSNR requirement and the lowest BER floor but the worst tolerance of CD. The detailed experimental investigation is conducive to promote the practical application of SHD in different short-reach scenarios.

Hybrid integrated chip-scale laser systems

Photonic integrated circuits (PICs) allow for the rapid advancement of a wide range of optical devices on a compact platform, making them more useful and readily available in the commercial market. Various materials such as III–V semiconductors, silicon, silicon nitride, lithium niobate, and polymers are used to create PICs with certain unique properties. Hybrid integration can combine multiple material platforms via optical coupling and realize multi-functional PICs that overcome the limitations of a single material platform. This allows for a broad application base for hybrid integrated PICs, greatly enhancing their usability and practicality. In this paper, we will discuss the methodology and applications of hybrid integration for chip-scale laser systems, including narrow linewidth, widely tunable external cavity lasers, laser beam combining, integrated frequency combs, and integrated Pockels lasers.

Hybrid integrated Si3N4 external cavity laser with high power and narrow linewidth.

We have designed and fabricated a hybrid integrated laser source with full C-band wavelength tunability and high-power output. The external cavity laser is composed of a gain chip and a dual micro-ring narrowband filter integrated on the silicon nitride photonic chip to achieve a wavelength tuning range of 55 nm and a SMSR higher than 50 dB. Through the integration of the semiconductor optical amplifier in the miniaturized package, the laser exhibits an output power of 220 mW and linewidth narrower than 8 kHz over the full C-band. Such a high-power, narrow-linewidth laser diode with a compact and low-cost design could be applied whenever coherence and interferometric resolutions are needed, such as silicon optical coherent transceiver module for space laser communication, light detection and ranging (LiDAR).

Low Noise Gain and Index Tailored External Cavity Laser Operating at 1310 nm for Performance Enhancements of IMDD Photonic Links

A novel gain and index tailored (GIT) external cavity laser (ECL) is presented. The single frequency laser demonstrates high power operation in excess of 250 mW and shot noise limited relative intensity noise (RIN) at 100 mW. This laser source is an ideal source for intensity-modulated direct detection (IMDD) photonic links. Link budget analysis is completed based on measured RIN and optical power. The analysis demonstrates that there are significant radio frequency performance advantages to operating at higher optical power while maintaining low RIN.

High-Power Source of Narrow-Band Radiation Based on Integrated External-Cavity Laser Diodes

High-Power Source of Narrow-Band Radiation Based on Integrated External-Cavity Laser Diodes

Sub-kHz-Linewidth External-Cavity Laser (ECL) With Si3N4 Resonator Used as a Tunable Pump for a Kerr Frequency Comb

Combining optical gain in direct-bandgap III-V materials with tunable optical feedback offered by advanced photonic integrated circuits is key to chip-scale external-cavity lasers (ECL), offering wideband tunability along with low optical linewidths. External feedback circuits can be efficiently implemented using low-loss silicon nitride (Si <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">4</sub> ) waveguides, which do not suffer from two-photon absorption and can thus handle much higher power levels than conventional silicon photonics. However, co-integrating III-V-based gain elements with tunable external feedback circuits in chip-scale modules still represents a challenge, requiring either technologically demanding heterogeneous integration techniques or costly high-precision multi-chip assembly, often based on active alignment. In this work, we demonstrate Si <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">4</sub> -based hybrid integrated ECL that exploit 3D-printed structures such as intra-cavity photonic wire bonds and facet-attached microlenses for low-loss optical coupling with relaxed alignment tolerances, thereby overcoming the need for active alignment while maintaining the full flexibility of multi-chip integration techniques. In a proof-of-concept experiment, we demonstrate an ECL offering a 90 nm tuning range (1480 nm–1570 nm) with on-chip output powers above 12 dBm and side-mode suppression ratios of up to 59 dB in the center of the tuning range. We achieve an intrinsic linewidth of 979 Hz, which is among the lowest values reported for comparable feedback architectures. The optical loss of the intra-cavity photonic wire bond between the III-V gain element and the Si <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">4</sub> -based tunable feedback circuit amounts to approximately (1.6 ± 0.2) dB. We use the ECL as a tunable pump laser to generate a dissipative Kerr soliton frequency comb. To the best of our knowledge, our experiments represent the first demonstration of a single-soliton Kerr comb generated with a pump that is derived from a hybrid ECL.

A mid-infrared laser microscope for the time-resolved study of light-induced protein conformational changes.

We have developed a confocal laser microscope operating in the mid-infrared range for the study of light-sensitive proteins, such as rhodopsins. The microscope features a co-aligned infrared and visible illumination path for the selective excitation and probing of proteins located in the IR focus only. An external-cavity tunable quantum cascade laser provides a wavelength tuning range (5.80-6.35 µm or 1570-1724cm-1) suitable for studying protein conformational changes as a function of time delay after visible light excitation with a pulsed LED. Using cryogen-free detectors, the relative changes in the infrared absorption of rhodopsin thin films around 10-4 have been observed with a time resolution down to 30ms. The measured full-width at half maximum of the Airy disk at λ = 6.08 µm in transmission mode with a confocal arrangement of apertures is 6.6 µm or 1.1λ. Dark-adapted sample replacement at the beginning of each photocycle is then enabled by exchanging the illuminated thin-film location with the microscope mapping stage synchronized to data acquisition and LED excitation and by averaging hundreds of time traces acquired in different nearby locations within a homogeneous film area. We demonstrate that this instrument provides crucial advantages for time-resolved IR studies of rhodopsin thin films with a slow photocycle. Time-resolved studies of inhomogeneous samples may also be possible with the presented instrument.

Investigation of thermal decomposition of nitrobenzene: An energetic material

Oxidation and pyrolysis mechanisms of energetic materials shape their macro properties such as autoignition and detonation. The high reaction-enthalpy, microsecond order reaction time, and toxicity necessitate investigation of their detailed chemical kinetics. A shock tube combined with laser absorption diagnostic provides time-resolved, high-sensitivity, and homogeneous environment to study thermal degradation of energetic and hazardous materials. In this work, we investigated the thermal fragmentation of nitrobenzene (C6H5NO2), a prototypical energetic material and nitro-aromatic representative, behind reflected shock waves. We studied its pyrolysis and decomposition branching channels over temperatures of 1155–1434 K and pressures of 0.82–1.78 bar. Channel-specific branching ratio was determined by employing a two-color laser absorption diagnostic. Two decomposition pathways are found to be significant under our experimental conditions. The first channel (k1) produces phenyl radical (C6H5) and NO2 while the second channel (k2) generates phenoxy radical (C6H5O) and NO. We monitored the reaction progress by tracing channel-specific products, i.e., phenyl radical (C6H5) and NO, using ultraviolet–visible (UV–vis) and infrared (IR) absorption diagnostics. UV–vis light at 445 nm for phenyl radical detection came from the frequency doubling of 890 nm light, generated by a titanium–sapphire laser, which was pumped by a green (532 nm) Nd:YAG laser. IR light at 5.517 μm for NO detection was generated by an external-cavity quantum cascade laser. We extracted the rate coefficients of the two decomposition channels and fitted them in Arrhenius form (units of s−1):k1=8.49×1014exp(−30476KT)k2=2.31×1013exp(−27618KT)Rate coefficients of both channels show positive temperature dependence while we did not observe discernible pressure dependence over 0.82–1.78 bar. Our measurements agree with a previous theoretical work qualitatively that, under these high-temperature conditions, the decomposition channel producing phenyl radicals and NO2 (k1) prevails over the NO-producing channel. Quantitatively, however, the theoretical work overestimates the importance of k1 channel, particularly at low temperatures. Our rate of production analysis shows that most of the phenyl radicals are consumed through their self-recombination while N atoms are mainly converted to NO2. This work benefits high-fidelity chemical modeling of the relevant safety and ignition aspects of nitrogen-containing energetic/hazardous materials.

Numerical simulation of linewidth compression dynamics of external-cavity semiconductor laser

We theoretically simulate the linewidth compression dynamics of the semiconductor laser with a single external-cavity feedback. The evolution time from the periodic oscillation state to the equilibrium state is calculated by tracking the change of the intrinsic linewidth. The influences of the external-cavity length and feedback level are also explored. The linewidth evolution time of the external-cavity semiconductor laser can be extended with longer external cavity length and higher feedback level. Simultaneously, the intrinsic linewidth can be compressed while the side mode suppression ratio will be decreased. The simulation work show that the dynamic linewidth compression can be obtained by single external-cavity feedback, and nevertheless it is difficult to achieve the single-frequency output, which can instruct the design of the dynamical parameter tuning of the external-cavity semiconductor laser.

A Model of Dual Fabry–Perot Etalon-Based External-Cavity Tunable Laser Using Finite-Difference Traveling-Wave Method

A physical model of an external-cavity tunable laser (ECTL) utilizing the vernier effect of a dual Fabry–Perot (FP) etalon is presented and simulated using the finite-difference traveling wave (FDTW) method. In this paper, we provide a detailed explanation of the physical principle and construction process of the model, as well as the simulation results for the laser. The model is precisely established by studying the time-dependent changes in the carrier concentration and optical field of different wavelengths inside the laser before reaching a steady state. By determining multiple parameters in the tuning region and gain region, the proposed model can calculate and predict various laser parameters, such as output power and side-mode suppression ratio (SMSR). Moreover, the FDTW method displays the change process of various parameters, such as carrier concentration and spectrum, in the convergence of various positions in the laser with femtosecond time resolution. This capability is promising for in-depth research on the inner mechanism of lasers.

Laser Sharing Uplink Polarization Division Multiplexing FBMC Passive Optical Network

In this paper, we proposed and experimentally demonstrated a laser sharing filter bank multicarrier passive optical network (FBMC-PON) uplink architecture, to provide high spectrum efficiency frequency division multiple access (FDMA) to the optical network terminals (ONTs) with aggregated uplink data rate of up to 100 Gb/s/λ for each optical network unit (ONU), in a fiber to the frontage (FTTF) scenario utilizing existing copper infrastructure. Intensity modulation (IM) and heterodyne detection are implemented, combined with polarization division multiplexing (PDM) to double the system capacity. The uplink performance of FBMC-PON is emulated with two asynchronous ONT bands in transmission over 20 km single mode fiber (SMF). FBMC with prototype filters (PFs) PHYDYAS, extended Gaussian filter (EGF) and isotropic orthogonal transform algorithm (IOTA) is discussed in comparison with orthogonal frequency division multiplexing (OFDM) in terms of frequency guard band and multiple access interference (MAI). The laser from an external cavity laser (ECL) is split and shared among ONTs. The experimental results show that FBMC can achieve significant improved receiver sensitivity compared to OFDM in the asynchronous uplink. FBMC with PHYDYAS can avoid MAI with frequency guard interval of one time the subcarrier spacing. With optical receiving power (ROP) of −23 dBm, to support 2, 4 and 8 ONTs, the required optical power of the narrow linewidth laser is respectively 10, 16 and 22 dBm with bit error rate (BER) at the hard decision forward error correction (HD-FEC) threshold.

Self-Injection Locked Silica External Cavity Narrow Linewidth Laser

A silica-based external cavity narrow linewidth laser is fabricated and experimentally demonstrated based on a commercial silica platform. An add-drop microring resonator and a 2×2 directional coupler in the silica chip form a wavelength-dependent and self-injection-locked external cavity. The linewidth-suppressing effect of the external cavity is theoretically calculated based on the chirp reduction theory, which shows that a long external cavity length at the resonant wavelength can be used to suppress the noise of a free-running laser. In the self-injection locked state, the measured intrinsic linewidth of the fabricated external cavity laser is 27 Hz, which is greatly reduced compared to the 49.7-kHz linewidth of the free-running state. The frequency stability is also measured to be improved by an order of magnitude from 4.52 × 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−8</sup> to 9.07 × 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−10</sup> at 1 s averaging time. The proposed narrow-linewidth laser shows the potential for massive production and can be used in various applications such as integrated microwave photonics, LIDAR, high-resolution metrology, and satellite communications.

High-SMSR wavelength-swept laser with a CL-band mode-hopping free tuning range

A high side-mode suppression ratio external-cavity wavelength-swept laser system with a wide mode-hopping free tuning range is developed. The proposed wavelength-swept laser is based on a single-angled facet gain chip in a classical Littman-Metcalf external-cavity configuration using a blazed diffraction grating as the feedback element. The output power, side-mode suppression ratio, and tunable range of the external-cavity wavelength-swept laser system are experimentally measured. Wide mode-hopping-free continuous wavelength tuning range about 100 nm in CL-band with a side-mode suppression ratio of more than 65.64 dB are realized. An output optical power of more than 14.12 dBm over the entire tunable region can also be achieved. The proposed external-cavity wavelength-swept laser system allows simultaneously high side-mode suppression ratio and no mode-hopping tunable radiation, thus opening a door for practical applications such as optical modulation schemes.

Laser-based sensing in the long-wavelength mid-infrared: chemical kinetics and environmental monitoring applications.

We present chemical kinetics and environmental monitoring applications in the long-wavelength mid-infrared (LW-MIR) region using a new diagnostic that exploits a widely tunable light source emitting in the LW-MIR. The custom-designed laser source is based on a difference-frequency generation (DFG) process in a nonlinear orientation-patterned GaAs crystal. The pump laser, an external-cavity quantum cascade laser, is tuned in a continuous-wave (cw) mode, while the signal laser, a C O 2 gas laser, is operated in a pulsed mode with a kilohertz repetition rate. The idler wavelength can be tuned between 11.58 (863.56c m -1) and 15.00µm (666.67c m -1) in a quasi-cw manner. We discuss the unique prospective applications offered by probing the LW-MIR region for chemical kinetics and environment-monitoring applications. We showcase the potential of the DFG laser source by some representative applications.

Fully Integrated Solid-State LiDAR Transmitter on a Multi-Layer Silicon-Nitride-on-Silicon Photonic Platform

We report a LiDAR transmitter incorporating both a hybrid-integrated tunable external cavity laser and a high-resolution 2-D optical phased array beam-steerer. Widely tunable single-mode lasing over a span of approximately 100 nm is achieved with >42 dB side-mode-suppression-ratio, 18 mW output power, and 2.8 kHz linewidth. Two-dimensional beam steering in a field-of-view of 140° × 16° exhibits a beam divergence of 0.051° × 0.016° measured in full width at half maximum. Leveraging the low propagation loss, negligible nonlinear loss, and low thermal sensitivity of silicon nitride, and combining the high mode confinement and efficient thermal tuning of silicon, the device affirms the feasibility of high-power on-chip lasing, power bottleneck elimination, and low on-chip insertion loss. It represents the first demonstration of a fully integrated LiDAR transmitter on the multi-layer silicon-nitride-on-silicon photonic platform, revealing the potential of complementary integration in the effort toward a LiDAR transmitter of sufficient optical power budget.

Integrated Photonic Device for Wavelength-Stable Laser Oscillation and Simultaneous Input Coupling

A guided-mode-resonance device for both narrow-band retroreflection and waveguide input coupling was designed and fabricated for operation wavelength of 1550 nm. It consists of a focusing grating coupler (FGC) integrated in a waveguide cavity resonator constructed by a pair of distributed Bragg reflectors (DBRs) on a reflection substrate. The size of the FGC was 31 × 20 μm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> . The device was used as a laser mirror of an external cavity laser. The oscillation wavelength was fixed to the retroreflection wavelength, and the laser power was coupled to a waveguide. The coupled power depends on the length of one DBR. The optimal length for the maximum coupling was also discussed theoretically and experimentally.

High-resolution molecular fingerprinting in the 11.6-15 µm range by a quasi-CW difference-frequency-generation laser source.

We report an approach for high-resolution spectroscopy using a widely tunable laser emitting in the molecular fingerprint region. The laser is based on difference-frequency generation (DFG) in a nonlinear orientation-patterned GaAs crystal. The signal laser, a CO2 gas laser, is operated in a kHz-pulsed mode while the pump laser, an external-cavity quantum cascade laser, is finely mode-hop-free tuned. The idler radiation covers a spectral range of ∼11.6-15 µm with a laser linewidth of ∼ 2.3 MHz. We showcase the versatility and the potential for molecular fingerprinting of the developed DFG laser source by resolving the absorption features of a mixture of several species in the long-wavelength mid-infrared. Furthermore, exploiting the wide tunability and resolution of the spectrometer, we resolve the broadband absorption spectrum of ethylene (C2H4) over ∼13-14.2 µm and quantify the self-broadening coefficients of some selected spectral lines.

Wide-range external-cavity tunable semiconductor laser with mode-hopping free

Wide-range external-cavity tunable semiconductor laser with mode-hopping free