Experimental Investigation Research Articles

Experimental investigation of the small-scale prototype of the dew point water recovery system

The article presents experimental investigation of the Dew Point Water Recovery (DPWR) system designed for clean water recovery using the dew point cooling phenomenon. The technology is a novel distillation process which allows for highly efficient water recovery. It is a first distillation technology which allows for water distillation through direct contact with atmospheric air. The authors designed, built, and tested an original prototype of a laboratory-scale DPWR system to verify its basic operating principles and perform performance analysis. It was shown that on average 10 × 10−6 m3 of clean water could be recovered from each cubic meter of the supply air with an average GOR of 1.9. Although the operation of the DPWR system requires electricity to drive fans, pumps and other associated equipment, the actual driving force of the system is thermal energy. The average thermal energy demand of the DPWR system was 370 kWh/m3, and more than half of this energy was based on the thermodynamic potential of the supply air. Based on experimental data, the mathematical model of the DPWR system was verified and it was found that the average relative discrepancy in predicting air temperature did not exceed 8%, and in predicting air humidity: 5%. The conducted experiments confirmed that the proposed DPWR system is feasible and has the potential to fill the technological gap in terms of a low-energy and easily accessible water recovery method.

Experimental Investigation for the Preparation of Taro Leaf Nanoparticles by Sol-Gel Method and its Characterization

Abstract: In the present work, nano particles of Taro leaf were successfully synthesized chemically by modified Sol-gel method. Methanol is used as a solvent and buffers are added to take care for the homogeneity and PH value of the solution. Compared to micro particles, Nanoparticles have advanced characteristics and distinctly different properties. Taro leaf nanoparticles are one of the leaves nanoparticles which has varied and different properties when compared to other. Taro Leaf nanoparticles have considerable attention due to their attractive physical and chemical properties, Silver nitrate is taken as the metal precursor and sodium borohydride as a reducing agent. This preparation is simple, but the great care must be exercised to make stable particles. Here the Taro leaf nanoparticles are synthesized by sol gel process. Therefore the nanoparticles are characterized by the different techniques like SEM to find the size morphology and composition of leaf nanoparticles, XRD to know the lattice parameters. The peaks in the XRD pattern are in good agreement with the standard values.

Hydroponic Multilayer Farming Automation with IOT

Abstract: This study introduces a novel high-tech, small-scale hydroponic system utilizing Internet of Things (IoT) technology for cultivating leafy vegetables. It employs low-cost materials and sensors for remote monitoring and process automation, addressing challenges like rural population decline and adverse climate changes. Experimental investigations focused on lettuce cultivation demonstrated the system's ability to maintain optimal environmental parameters, achieving 75% seed germination. Key benefits include easy management, remote monitoring, and suitability for small to medium-sized vegetable growers, enabling sustainable year-round farming of leafy greens indoors.

Experimental Investigation of Partial Replacement of Cement in Concrete using Waste Glass Powder

Abstract: The construction industry is the second largest industry in the world & concrete is prime material used in it [5]. The use of concrete generates lots of heat during hydration process. It directly contributes to global warming. Also cement is costly material & its storage is also difficult. The cement plays important role of binding in concrete. It contains lime as main constituents. So to reduce this ill effect of cement one must find the alternatives for cement which can perform the same role in concrete. This study represents the experimental investigation of effect of partial replacement of cement by glass powder on strength of concrete & other factors like workability, water cement ratio, and heat of hydration. Glass contains lime as its one of main constituent. The cement was replaced with glass powder by 5%, 10%, 15%, and 20%. The compressive strength, flexural strength & split tensile strength are tested for these replacements. Also economical aspect is observed along with. It is observed that physical & chemical properties of glass are almost similar to cement. So in this study an attempt is made to investigate the effect of partial replacement of cement by glass powder in concrete to make it as a special concrete

Experimental investigation on flexural performance of steel-UHPC composite beams with steel shear keys

Test results of steel-ultra high performance concrete (UHPC) composite beams with welded steel shear keys (SSKs) under four-point bending are presented in this paper. The objective of the investigation is to reduce the self-weight and manufacturing cost of large-span structures. The study investigates the effects of strength of concrete slab, type, spacing and size of SSK, and concrete slab height and width on flexural behavior of composite beams. The experimental results demonstrate that enhancing concrete strength, reducing SSK spacing, increasing concrete slab size, and using large-size SSK can all significantly enhance the flexural performance. The composite beams with welded SSK exhibit a maximum relative slip of less than 4 mm, while the counterpart with welded bolts has a maximum relative slip greater than 4 mm. The study shows that the welded SSK is more effective than welded bolts in improving the interface shear performance of composite beams and improving the stiffness and load capacity. Additionally, the study defines four failure modes of steel-UHPC composite beams, and the formulae for flexural capacity is developed based on the reasonable basic assumptions. The calculated results fit well with the tested results. The research findings can be provided as a technical support for the design and application of steel-UHPC composite beams.

Desymmetric Hydrogenation of meso-Dicarboxylic Acids.

Efficient transformation of platform chemicals into key intermediates has been increasingly important for the pharmaceutical industry. The development of the catalytic reduction of abundant carboxylic acids with molecular hydrogen has been of both practical and theoretical value. We herein report the homogeneous hydrogenation of dicarboxylic acids with the strategy of desymmetrization. Using a rhodium/bisphosphine catalyst, one carboxyl group of meso-diacids was selectively reduced to yield chiral lactones with satisfactory enantioselectivity. This method provides a straightforward approach to produce chiral lactone intermediates for the manufacture of biotin, telaprevir, and other antivirus drugs. Both experimental and computational investigations were carried out, revealing a novel neighboring group coordination mechanism in the catalytic cycle.

High-Entropy Alloy Electrocatalysts Bidirectionally Promote Lithium Polysulfide Conversions for Long-Cycle-Life Lithium-Sulfur Batteries.

High-entropy alloys (HEAs) have attracted considerable attention, owing to their exceptional characteristics and high configurational entropy. Recent findings demonstrated that incorporating HEAs into sulfur cathodes can alleviate the shuttling effect of lithium polysulfides (LiPSs) and accelerate their redox reactions. Herein, we synthesized nano Pt0.25Cu0.25Fe0.15Co0.15Ni0.2 HEAs on hollow carbons (HCs; denoted as HEA/HC) by a facile pyrolysis strategy. The HEA/HC nanostructures were further integrated into hypha carbon nanobelts (HCNBs). The solid-solution phase formed by the uniform mixture of the five metal elements, i.e., Pt0.25Cu0.25Fe0.15Co0.15Ni0.2 HEAs, gave rise to a strong interaction between neighboring atoms in different metals, resulting in their adsorption energy transformation across a wide, multipeak, and nearly continuous spectrum. Meanwhile, the HEAs exhibited numerous active sites on their surface, which is beneficial to catalyzing the cascade conversion of LiPSs. Combining density functional theory (DFT) calculations with detailed experimental investigations, the prepared HEAs bidirectionally catalyze the cascade reactions of LiPSs and boost their conversion reaction rates. S/HEA@HC/HCNB cathodes achieved a low 0.034% decay rate for 2000 cycles at 1.0 C. Notably, the S/HEA@HC/HCNB cathode delivered a high initial areal capacity of 10.2 mAh cm-2 with a sulfur loading of 9 mg cm-2 at 0.1 C. The assembled pouch cell exhibited a capacity of 1077.9 mAh g-1 at the first discharge at 0.1 C. The capacity declined to 71.3% after 43 cycles at 0.1 C. In this work, we propose to utilize HEAs as catalysts not only to improve the cycling stability of lithium-sulfur batteries, but also to promote HEAs in energy storage applications.

Experimental Investigation on the Effect of Heating Oil and Tyre Pyrolysis Oil Combustion in an Evaporative Combustion Chamber

This research aims to delve into the intricacies of combustion processes, specifically focusing on heating oil and a blend of heating oil with Tire Pyrolysis Oil (TPO) in a self-developed evaporative combustion chamber featuring steam injection. The primary objective is to scrutinize the impact of steam injection on the combustion dynamics. Conducting a series of tests, the investigation involved the meticulous manipulation of stoichiometric ratios while introducing ambient air through gravity fuel flow. Subsequent iterations of these tests incorporated the introduction of steam into the ambient air stream. The examination encompassed the combustion of both heating oil and the TPO blend within the combustion chamber. The evaluation criteria comprised an in-depth analysis of flame characteristics, temperature distribution within the combustion chamber, and the quantification of emissions such as particulate matter (PM), nitrogen oxides (NOx), carbon dioxide (CO2), carbon monoxide (CO), and water vapor (H2O). Throughout the experimentation phase, commercially available diesel fuel served as the primary fuel source. To facilitate the tests, the combustion chamber under scrutiny was seamlessly integrated into an AVL engine test bench system. Essential parameters, including fuel consumption, were meticulously gauged using an AVL 735 fuel flow meter, while fuel temperature was monitored using the AVL 745 fuel temperature conditioning system. The intake air, a crucial element in the combustion process, was quantified with precision using an AVL Flowsonix sensor. Emission measurements were conducted meticulously using state-of-the-art equipment, with gaseous emissions analyzed using an AVL FTIR AMA i60 exhaust gas analyzer. Simultaneously, soot emissions were quantified through employment of an AVL Micro Soot sensor. This comprehensive approach not only delves into the fundamental aspects of combustion but also extends its reach to the exploration of innovative techniques, such as steam injection, to enhance combustion efficiency and reduce emissions. The integration of advanced measurement tools ensures a robust and thorough analysis of the combustion process and its environmental implications.

Development of Technology for the Bioleaching of Uranium in a Solution of Bacterial Immobilization

This study presents findings regarding the kinetics of ferrous iron oxidation in solution mediated by Acidithiobacillus ferrooxidans bacteria within a continuous-flow bioreactor employing diverse types of immobilizers. The objective is to augment the rate of ferrous iron oxidation in solutions utilizing an immobilizer for Acidithiobacillus ferrooxidans strains. Immobilization represents a promising avenue for enhancing the efficiency of Fe2⁺ oxidation via acidophilic ferrooxidizing bacteria, leading to a several-fold increase in oxidation rate. A comparative analysis was conducted to evaluate the efficacy of different types of immobilizer in facilitating iron oxidation within a continuous-flow bioreactor, including the application of wood chips coated with Fe(OH)3. The results indicate that wood chips coated with iron hydroxide serve as effective type of immobilizer, facilitating the robust attachment of Acidithiobacillus ferrooxidans via electrostatic interactions between negatively charged bacteria and positively charged surfaces. Experimental investigations were conducted using novel immobilization matrices in pilot-scale tests simulating the underground borehole leaching (UBL) of uranium. The bioactivation of leaching solutions enhances the efficiency and environmental compatibility of UBL compared to conventional chemical oxidation methods. The relationships between redox potential and ferric iron content in bioactivated solutions during the UBL of uranium were delineated. The significance of this study lies in its elucidating the pivotal role of Fe2⁺ oxidation in uranium extraction processes, particularly in the context of UBL. By employing bioactivation mediated by Acidithiobacillus ferrooxidans, the study demonstrates not only enhanced uranium extraction efficiency, but also markedly improved environmental sustainability compared to traditional chemical oxidation methods. The findings reveal crucial correlations between redox potential and ferric iron concentration in bioactivated solutions.

Experimental investigation on impact strength of hybrid fibre reinforced concrete containing steel and polypropylene

Experimental investigation on impact strength of hybrid fibre reinforced concrete containing steel and polypropylene

Experimental investigation and multi-objective optimization of a novel multi-fluid heat exchanger performances using response surface methodology and genetic algorithm

Experimental investigation and multi-objective optimization of a novel multi-fluid heat exchanger performances using response surface methodology and genetic algorithm

Experimental and numerical investigations of the water surface profile and wave extrema of supercritical flows in a narrow channel bend

Supercritical flows in channel bends, e.g., in steep streams, chute spillways, and flood and sediment bypass tunnels (SBTs), experience cross-waves, which undulate the free surface. The designs of these hydraulic structures and flood protection retaining structures in streams necessitate computing the locations and water depths of the wave extrema. This study numerically and experimentally investigates the water surface profiles along the sidewalls, the wave extrema flow depths, and their angular locations in a narrow channel bend model of the Solis SBT in Switzerland. The 0.2 m wide and 16.75 m long channel has a bend of 6.59 m radius and 46.5° angle of deviation. The tested flow conditions produced Froude numbers ≈ 2 and aspect ratios ranging from 1.14 to 1.83. Two-phase flow simulations were performed in OpenFOAM using the RNG k–ε turbulence closure model and the volume-of-fluid method. The simulated angular locations of the first wave extrema and the corresponding flow depths deviate marginally, within ± 6.3% and ± 2.1%, respectively, from the experimental observations, which signifies good predictions using the numerical model. Larger deviations, especially for the angular locations of the wave extrema, are observed for the existing analytical and empirical approaches. Therefore, the presented numerical approach is a suitable tool in designing the height of the hydraulic structures with bends and conveying supercritical flows. In the future, the model’s application shall be extended to the design of the height and location of retaining walls, embankments, and levees in steep natural streams with bends.

Experimental Investigation on the Behavior of Strip Footing on Prestressed Geocell Reinforced Sand

Experimental Investigation on the Behavior of Strip Footing on Prestressed Geocell Reinforced Sand

Lanthanide-Sensitized Upconversion Iridium Complex via Triplet Energy Transfer.

Cyclometalated iridium (Ir) complexes demonstrate impressive capabilities across a range of fields, including biology and photocatalysis, due to their tunable optical characteristics and structure flexibility. However, generating upconversion luminescence of Ir complexes under near-infrared light excitation is challenging. Herein, by employing lanthanide-doped upconversion nanoparticles (UCNPs) as the sensitizer, a new strategy is demonstrated to gain upconversion luminescence of Ir complexes via triplet energy transfer. This design relies on a rationally designed hybrid of core-shell structured NaYbF4:Tb@NaTbF4 UCNPs and new Ir phosphonate complexes, in which UCNPs can migrate upconverted energy to the surface of nanoparticles through Tb3+-mediated energy migration and then sensitize the upconversion luminescence of Ir complexes upon 980nm excitation. Both experimental and theoretical investigations highlight the significance of triplet energy transfer from excited Tb3+ ions to the triplet state of Ir complexes in the sensitization of upconversion luminescence of Ir complexes. These findings may open exciting avenues for fabricating hybrid Ir materials with new functions and driving the development of UCNP-based nanomaterials.

Experimental and Numerical Investigations for Impact Loading on Platform Decks

Experimental measurement and numerical simulations were carried out for investigating the impact loading behavior of platform decks under regular and irregular wave actions. In the numerical simulation section, a full-scale numerical wave tank was established using STAR-CCM+ software. A decreased tendency can be observed for an increased relative length of platform when the incident wave length is double the deck length. The increased deck height can also decrease impact loading on the platform, which is due to the platform being far away from the incident wave. Impact loading on the deck decreases with the increase in inclination angle, which can be explained by the deck bottom being directly exposed to the incident wave at negative inclination angles. Finally, the variation tendency of impact loading on platform decks under irregular wave actions is similar to that under regular wave actions, including the averaged values and significant values.

Extremely stable system of 1-haloselanyl-anthraquinones: experimental and theoretical investigations.

Highly stable selanyl halides, 1-ATQSeX (X = I (1), Br (2) and Cl (3)), were prepared. The structures of 1, 2, 6 (1-ATQSeX: X = Me) and 7 (1-ATQBr) were determined. QC calculations were performed on 1-3, 4 (X = F), 5 (X = H), 6, 7 and 8 (X = SeATQ-1). The O⋯Se distances in 1-4 from the sum of the vdW radii of the atoms (Δr(Se, O1)) were less than -1 Å, in magnitude, which must be the driving force for the high stability. The O-*-Se interactions seem stronger in the order of 1 < 2 < 3 < 4. The intrinsic dynamic and static natures of O⋯Se and/or Se⋯X in 1-8 are elucidated by QTAIM dual functional analysis (QTAIM-DFA). The Se-*-I, Se-*-Br, Se-*-Cl and Se-*-F interactions in 1-4 are predicted to have the natures of covalent, TBP with CT, TBP with CT, and typical HB with covalency, respectively, whereas O-*-Ses in 1-4 are all predicted to have the nature of MC with CT. The Se-*-H, Se-*-CMe and Se-*-Se interactions in 5, 6 and 8 are all predicted to have the covalent nature, while O-*-Ses in 5, 6 and 8 are all predicted to have the nature of typical HB with no covalency. The E(2) values of 1-6 and 8 are calculated with NBO analysis, and correlate excellently with Δr(Se, O1), except for Se-*-F, for which E(2) is evaluated to be much larger. The E(2) values also correlate very well with Cii-1 for all Se-*-X in 1-4, although data from 5, 6 and 8 deviated from the correlation, where Cii is the diagonal element of the compliance (force) constant for the internal vibrations. The behaviour of the interactions is further examined based on the QTAIM-DFA parameters of θ and θp. The stabilizing effect is further confirmed by the calculations with the ν(CO) values analyzed carefully.

Experimental investigation of 3D printed polylactic acid and polylactic acid – hydroxyapatite composite through material extrusion technique for biomedical application

In biomedical industries, composite additive manufacturing are employed for customization, quicker production, efficient use and capital reduction. This experimental work focuses on the development of poly lactic acid (PLA) and novel extruded hydroxyapatite (HA) reinforced poly lactic acid (HPLA) by material extrusion (ME) technique and their properties were compared with that of standard 3D printed PLA. The extruded composite filaments were subjected to thermal characterization (DSC, TGA) and chemical characterization (FTIR) to ensure filament quality and its implementation in ME technique for 3D printing process. In addition, the melt compounded composite filaments were subjected to annealing to observe the influence of heat treatment upon their mechanical properties and thereby to validate their potential to resist breakage during ME process. Taguchi orthogonal array method using MiniTab software is employed to execute the parameter optimization for the 3D printing process. The 3D printed tensile, flexural and impact specimens, using pure PLA and extruded composite filaments, as per American Society for Testing and Materials (ASTM) standards were subjected to a comparative experimental study which showed that 3D printed specimens using PLA and HPLA performed better than that of standard PLA specimens due to the improvement in their crystalline nature. The ruptured specimens were subjected to microstructural characterization (optical microscopy, SEM) to observe failure modes and ash content test was conducted to validate the homogenous distribution HA filler particles in PLA matrix. In addition, mechanical characterization was also performed on 3D printed bone plate/bone scaffold application using extruded filaments of PLA and HPLA, as per ASTM F543 standards, to validate incorporation of the composite filaments in real-time application in biomedical industry.

Experimental investigations to assess surface fatigue failure in rolling contact bearing

Rolling element bearings are the most important components in almost all rotating machines. These bearings are often subjected to repetitive load cycles at different operating conditions. Excessive loads, speeds, and improper operating conditions lead to the propagation of defects on their load-bearing surfaces, thereby causing a negative impact on the performance of rotating machines. This paper presents the results of experimental investigations to assess wear propagation in roller bearings using lubricant degradation, vibration, and statistical parameter analysis methods. A roller bearing setup was developed in the laboratory, and the test bearing (NJ 307E) was subjected to fatigue tests over a period of 900 h. The bearing was operated at a speed and radial load of 800 rpm and 1 kN, respectively. The film thickness analysis revealed a transition in lubrication regimes during 600–900 h of operation. Grease structure degradation and oxidation analyses were carried out using scanning electron microscope images and the Fourier transform infrared radiation technique. Further, the vibration signals are extracted from the bearing housing at regular intervals. Using the fast Fourier transform technique, these vibration signals were used to analyze bearing fault frequencies to highlight the faults developed on bearing contact surfaces. The statistical features of vibration signals such as root mean square, kurtosis, and crest factor were used to assess the severity of wear propagated on the bearing contact surfaces. Integrating tribological and vibration parameter analysis techniques provided a reliable assessment of surface fatigue wear propagated on the roller-bearing contact surfaces.

Experimental investigation of influence of amide polymer on loess for subgrade

The effects of moisture and drying shrinkage can lead to uneven settlement, cracking, and other diseases in loess subgrade. The objective of this study was to investigate the effects of amide polymer (AP) on the permeability, mechanical properties and crack resistance of loess by orthogonal experiments. The basic properties of AP and the permeability, mechanical properties, and dry–wet variation properties of polymer-modified loess were tested, and a scale model verification and simulation analysis were conducted. In this paper, water migration in subgrade is regulated by improving the water sensitivity of loess. By reducing the variation range of subgrade water content, the stress accumulation in subgrade caused by water is weakened. The results show that the curing time and mechanical properties of AP are directly affected by the oxidant and reducing agent, and the mechanical properties of AP are compatible with the characteristics of loess. AP filled the grain gap and reduced the permeability of loess by 34.05–280.83%. The ductility of polymer-modified loess is significantly increased, and the strain of peak strength is increased by 17.21–126.36%. AP can regulate moisture change, reduce the surface tension between particles, and reduce stress concentration. The strength loss rate was reduced by 19.98–51.21% by enhancing the cracking resistance and weakening the strength loss caused by dry and wet cycling. The increase of upper layer moisture content in the scale model of polymer-modified loess subgrade is reduced by 31.38–36.11%.

Continuous blood exchange in rats as a novel approach for experimental investigation

Blood exchange therapy, specifically Whole blood exchange (WBE), is increasingly being utilized in clinical settings to effectively treat a range of diseases. Consequently, there is an urgent requirement to establish convenient and clinically applicable animal models that can facilitate the exploration of blood exchange therapy mechanisms. Our study conducted continuous WBE in rats through femoral and tail vein catheterization using dual-directional syringe pumps. To demonstrate the applicability of continuous WBE, drug-induced hemolytic anemia (DIHA) was induced through phenylhydrazine hydrochloride (PHZ) injection. Notability, the rats of DIHA + WBE group all survived and recovered within the subsequent period. After the implementation of continuous WBE therapy day (Day 1), the DIHA + WBE group exhibited a statistically significant increase in red blood cells (RBC) (P = 0.0343) and hemoglobin (HGB) levels (P = 0.0090) compared to DIHA group. The rats in the DIHA + WBE group exhibited a faster recovery rate compared to the DIHA group, indicating the successful establishment of a continuous blood exchange protocol. This experimental approach demonstrates not just promising efficacy in the treatment of DIHA and offers a valuable tool for investigating the underlying mechanisms of blood exchange. Furthermore, it has a great potential to the advancement of biomedical research such as drug delivery exploration.