Excessive Heat Research Articles

Potential for Utilizing Organic Waste as a Heat-Insulating Composite

The ever-increasing global population growth has a direct impact on residential building demand, which often does not keep pace with construction growth. This condition leads to an increase in housing density and a decrease in construction quality, which contributes to excessive heat inside homes. Therefore, this research explores the use of organic waste, specifically reeds and young coconut fiber, as environmentally friendly thermal materials to reduce dependence on artificial energy and its negative impacts. The high cellulose content in reeds and the fiber in young coconut fiber is a combination that has the potential to create an effective heat absorber. Product composition material testing was carried out using a thermogun, and the results were analyzed using the one-way Analysis of Variance (ANOVA) method. This research aims to utilize the potential of organic waste to produce insulation that can reduce heat temperatures in buildings, with the hope of finding alternative materials that are more sustainable and environmentally friendly.

Designing orthopaedic seat cushion made of rattan using quality function deployment approach

Using ergonomic orthopaedic chairs can address spinal issues, particularly HNP, due to their flexible and elastic properties. By achieving optimal ergonomic design, various positive aspects can be achieved, such as increasing work quality productivity and reducing the cost of injuries or accidents. This research demonstrates diverse product design approaches to enhance posture health ergonomics, address specific musculoskeletal disorder issues, and consider local needs and available materials. Rattan is a tropical vine widely used in the furniture industry and predominantly found in wooded areas such as Indonesia. This research combines market research, morphology, ergonomic study, concept selection, QFD, HoQ, stiffness test, and prototype review. The QFD method was chosen in this study due to its excellence in connecting consumer desires with the product development process. Data of respondents consist of 51 % of respondents were male, 49 % were female, 88 % were aged between 18 and 34 years old, and 10 % were aged between 35 and 54 years old. The approach of 6 stages of product design as the primary framework for developing our product such as: planning, concept development (concept screening, product morphology, concept selection), system-level design, detailed design, testing, refinement and launching. Based on the calculations using the HOQ, it is identified that the primary focus in designing the rattan-based orthopaedic seating, lies in the orthopaedic design that provides maximum comfort for the spine. The comparison results indicate that the stiffness level of rattan weaving is nearly like latex, with a similarity percentage of 89 %. Data analysis using the QFD method indicates that the primary priority aspect is the orthopaedic design, followed by the selection of quality materials, cost-effectiveness, versatility, and appealing design aspects. Rattan's superior air circulation provides comfort by preventing excessive heat accumulation, excellence in strength and durability, ensuring ease of lightweight modelling, and providing more sustainable material.

Comparison of Intraosseous Temperature Rise in Different Surgical Guide Systems: An In Vitro Study

Aim: This study proposes to investigate the influence of various surgical guide designs on the generation temperature in the cortical and cancellous regions of the osteotomy site. The working hypothesis was that open guides are more efficacious in controlling excessive heat generation in cortical and cancellous areas. Materials and Methods: Implant osteotomy was performed on specimens simulating D3 bone density using surgical guides produced with three different designs: an open guide, a guide with an external cooling channel, and a closed guide. Temperature increases occurring in the cortical layer from a depth of 2 mm and in the cancellous layer from a depth of 10 mm were measured with type K thermocouples. Results: Temperature averages recorded from a depth of 2 mm during osteotomy show statistically significant differences between groups ( p = .003). The temperature rise in the group using a closed surgical guide was significantly higher than in the groups using an open surgical guide and a surgical guide with an external cooling channel on the cortical layer, while the temperature increase did not show any significant difference in both cortical and cancellous layers between the open guide and guide with external cooling channel. Temperature averages recorded from a depth of 10 mm do not show statistically significant differences between groups ( p = .054). Conclusion: Using open surgical guides or surgical guides with external cooling channels among the guided surgical systems is a more reliable way to keep the thermal increase under control.

The Increase in Urban Heat Due to Global Warming Can be Significantly Affected by the Structure of the Land Use and Land Cover

ABSTRACTUrban populations are increasingly exposed to excessive heat. Heat distribution in the urban environment can be affected by several factors, including the spatial arrangement of land use/land cover (LULC) that is specific to a given city. This study applies a climate model with urban canopy parameterisation to downscale future climate projections and simulate the spatio‐temporal pattern of heat in the urban environment to better understand the effect of LULC structure on its distribution. Heat conditions are characterised by climate indices that are well representative in two mid‐sized Central European cities of Brno and Ostrava (Czech Republic). Our results show that the annual number of hot days (HOT), summer days (SUD), tropical nights (TRN) and warm nights (WAN) will increase significantly (p < 0.01) in the 21st century in both cities. The model also simulates a more intensive increase and a higher spatio‐temporal variability in all indices in Brno compared to Ostrava. In Brno, the annual number of HOT and TRN is projected to be more than 500% of the 1981–2010 reference period's value by the end of the 21st century under the RCP 8.5 scenario. To determine the causes of the differences in heat distribution, we applied LULC configuration metrics and correlation analysis using various geographical factors. The higher risk of urban heat in Brno compared to Ostrava can be attributed to a more homogenised and less fragmented LULC structure and to the more substantial role of altitude in the complex terrain of Brno. Other factors, such as the presence of impervious surfaces and vegetation, have a similar effect on the variability of the studied indices in both cities. Urban planners should consider the role of the LULC structure and the changes that can be made in a city when designing adaptation measures to mitigate the effects of urban heat.

A Study on the Green Laser Weldability of Copper-aluminum Battery Materials

Copper is widely utilized in electric vehicle batteries due to its excellent electrical conductivity, lightweight, and excellent corrosion resistance. However, copper has a high reflectivity of about 97% for infrared lasers, which makes it difficult to achieve stable welding quality. This study investigated using a green laser to weld nickel-coated copper and aluminum materials. After performing welding by changing the laser power and scan speed, the weld cross-section was observed with an optical microscope, and it was confirmed that the welding penetration depth and bead width increased as the heat input increased. The spatter on the bead surface and defects such as pores and cracks in the weld were caused by excessive heat input. Analysis of the weld cross-section using SEM-EDS showed that high heat input increased the formation of intermetallic compounds including CuAl2 and Cu9Al4. The mechanical properties of the weld were examined using a shear tensile test. The analysis results showed that intermetallic compounds caused brittleness in the weld joint, which lowered mechanical properties and caused defects such as pores and cracks. P60 (1.2 kW, scan speed: 250 mm/s), P80 (1.6 kW, scan speed: 375 mm/s), and P100 (1.2 kW, scan speed: 375 mm/s) were examples of excellent mechanical quality. The fastest welding condition, P100 (power: 2 kW, scan speed: 450 mm/s), was suggested as the most efficient welding condition.

Long-term recurrent exposure to excessive heat in the east Mediterranean and climate resilience development – a case study in Israel

This work studies long-term trends of observed meteorological parameters and of exposure to excessive heat over 74 years in Israel (1950–2023). We report an increasing trend of recurring exposure of the Israeli population to excessive heat during most of the summer noon hours, with the heat index often above the physiologically no-risk threshold. Specifically, since the beginning of the millennium, a significant increase in summertime decadal means of ambient noontime temperature (Ta), absolute humidity (AH), and heat index (HI) is evident relative to the 1950’s (Ta: 0.06 °C/year, AH: 0.06 g/m3year, HI: 0.09 °C/year). The experienced increase summertime thermal discomfort by the Israeli population results from the significant and synergistic increase in co-exposure to ambient temperature and humidity. Indeed, long-term satellite data (Landsat 1984–2021) of the east Mediterranean Sea Surface Temperature (SST) reveal a significant change (SST: 0.05 °C/year), which elucidates the corresponding increase in the absolute humidity. Leishmaniasis is a climate-related vector-borne infectious disease. However, the 1956–2017 leishmaniasis incidence rates in Israel do not correlate with the significant increase in the ambient temperature and heat index, representing development of climate resilience in terms of administrated prevention measures (namely, systematic adaptation) to this climate-related disease.

A Randomized Controlled Study Comparing And Evaluating The Peri-Operative Outcomes Of Using Straight Versus Angled Handpieces During The Surgical Extraction Of Impacted Mandibular Third Molars

Introduction: The straight handpiece is one of the most commonly used instruments in third molar surgeries. However, its use has been suggested to carry a potential risk of soft tissue injury, possibly due to its design limitations leading to direct positioning and excessive heating, which could contribute to soft tissue damage. Direct positioning can sometimes cause excessive heating, leading to potential soft tissue damage. Additionall its design might limit accessibility in the confined surgical area, making it more difficult to maneuver effectively. This study aims to evaluate whether using an angled handpiece enhances accessibility and reduces the risk of soft tissue damage during surgical procedures. AIM: Comparison and evaluation of the use of straight and angled handpieces on perioperative outcomes in operative removal of obstructed lower third molars. Materials and Methods: This research included 30 healthy participants aged 18 to 40, all of whom were undergoing extraction of impacted lower third molars at the Department of Oral and Maxillofacial Surgery. Participants were randomly assigned to two groups.: Group A, where the extraction was carried out using an angled handpiece, and Group B, where a straight handpiece was employed. Results: No statistically significant differences were found in postoperative pain, edema, mouth opening, or surgical time between the angled and straight handpiece groups. Conclusion: The findings of our research indicate that there were no notable statistical differences observed between the two groups in relation to post-operative outcomes such as pain, edema, mouth opening, or surgical time. The lack of statistical significance may be attributed to the small sample size, emphasizing the importance of larger cohorts for a more accurate assessment of the clinical impact. However, operator comfort was reported to be better with angled handpieces in certain cases. Category: Dentistry, Pain Management, Patient Care

Energy and exergy analysis of photovoltaic systems integrated with pulsating heat pipe and hybrid nanofluids

Solar energy is harnessed from solar radiation and converted into various forms of energy, primarily electricity. It is a crucial part of the renewable energy landscape due to its abundance, sustainability, and potential to reduce greenhouse gas emissions. Photovoltaic (PV) panels have become a critical component in the transition toward sustainable energy; however, the efficiency and longevity of PV systems are significantly influenced by their operating temperature. Excessive heat can reduce the efficiency of PV cells and accelerate material degradation. Pulsating heat pipes (PHPs), with their excellent thermal management capabilities, present a promising solution to these challenges. This paper comprehensively investigates the effect of incorporating a three-dimensional PHP into PV systems, using working fluids with varying thermal properties, namely water, graphene oxide (GO) nanofluid with three different concentrations (0.2, 0.4, and 0.8 g/L) and their mixture with nano-encapsulated phase change material (Nano PCM), forming a hybrid nanofluid, at a concentration of 5 g/L. The collected data are analyzed from energy and exergy perspectives. The findings show that using Nano PCM in the nanofluid-based PV system (at the highest concentration) produces 22.3 Wh/day, increasing the system’s electrical power output by approximately 12 % compared to a PV panel with no cooling system. It outperforms the other systems studied, with the highest overall exergy efficiency of 35.4 %. The results also indicate an average improvement in first-law efficiency. Additionally, the study shows varying levelized costs of energy (LCOE) for the system cooled with different coolants.

The risk of hospitalization associated with hot nights and excess nighttime heat in a subtropical metropolis: a time-series study in Hong Kong, 2000–2019

Recent studies showed increased mortality risks after hot nights, but their effect on hospitalizations, especially in vulnerable populations, remains under-studied. Daily hospitalization, meteorological (including hourly), and air pollution data were collected for the hot seasons (May-October) of 2000-19 in Hong Kong. We derived three hot-night metrics: HNday28 °C, daily minimum temperature ≥28°C, the governmental definition of hot nights; HNe, hot night excess calculated by summing heat excess of hourly temperatures above 28°C at night; and HNday90th, hot nights classified using the 90th percentile HNe (17.7°C⋅h) as a cutoff. We fitted time-series regression with distributed lag nonlinear models to examine the associations of hot-night metrics with various hospitalizations. During the 3680 study days, 5,002,114 non-cancer non-external (NCNE) hospitalizations were recorded. Half (1874) of the days experienced excess nighttime heat (HNe>0) with a mean (SD) of 8.0 (6.8) °C⋅h; 499 and 187 hot nights were identified by HNday28 °C and HNday90th, respectively. Extreme HNe (99th percentile vs 0°C⋅h) was significantly associated with increased NCNE hospitalizations over lag 0-4 days by 3.1% [95% confidence interval: 1.5%, 4.8%] overall, with enhanced effects in elderly (5.3% [3.2%, 7.4%]), low-SES individuals (5.3% [2.8%, 8.0%]), and circulatory admissions (3.4% [0.2%, 6.8%]). HNday90th, reflecting extreme HNe, better identified hazardous hot nights than the official HNday28 °C. Excessive nighttime heat is significantly associated with increased hospitalizations, particularly affecting the elderly and socioeconomically disadvantaged individuals. Nighttime heat intensity should be incorporated in defining hot nights with public health relevance. British Heart Foundation.

Development of ITER first wall heat load feedback control

Real-time monitoring and control of thermal loads on tungsten plasma-facing components is mandatory for ITER to avoid their overheating during plasma discharges. For the Start of Research Operations (SRO) phase, dedicated First Wall Heat Load Control (FWHLC) functions are included in the ITER Plasma Control System (PCS) to prevent the development of excessive plasma heat loads on the inertially cooled first wall (FW). In this work, we propose a FWHLC design with a model-based approach, which features a simplified thermal model for the FW armour. This control-oriented model simulates the thermal response of ITER FW to slow changes in plasma equilibrium and energy, which during ITER operation will be monitored by the real-time wide angle infrared camera system. This allows computationally efficient runs for rapid controller performance assessment but can also assist operation scenario design by pre-empting potential heat load issues. FWHLC is designed to react to measured and predicted FW temperatures overcoming predesigned limits with real-time variations of the plasma shape or auxiliary power references, aiming to reduce thermal loads before a premature plasma termination is required to protect the FW. The new scheme is tested in closed loop simulations, where perturbations to nominal ITER low current scenarios are introduced in the wall thermal model to trigger the response of FWHLC, supporting the effectiveness of the proposed policy.

Feasibility and safety assessment of RF double applications in very high power and short duration ablation

BackgroundThe QDOT-MICRO catheter enables very high power and short duration (vHPSD) ablation. However, low first-pass isolation rates have been reported, possibly because of shallow lesion formation, necessitating deeper lesions to improve treatment outcomes. ObjectiveThis study aimed to confirm the safety and efficacy of double radiofrequency applications of vHPSD ablation in an in vivo beating swine heart model. MethodsEighteen swine were anesthetized and underwent vHPSD ablation using the QDOT-MICRO catheter at 90 W for 4 seconds, targeting a contact force of 10 g. Radiofrequency applications were performed as single application (SA) and double applications (DAs) with 4- to 8-second rest intervals. Lesion surface area and volume were measured postablation. ResultsA total of 337 atrial lesions and 74 ventricular lesions were created. Both 4- to 6-second DA and 7- to 8-second DA produced significantly larger and deeper lesions than did SA, with atrial surface lengths averaging 9.0 mm for 4- to 6-second DA, 9.2 mm for 7- to 8-second DA, and 8.0 mm for SA. Transmurality was observed at 100% for 4- to 6-second and 7- to 8-second DAs, while it was 94% for SA (P = .002). Ventricular lesion metrics followed similar trends. Except for 1 event of tiny char formation during 4-second DA in the ventricle, neither steam pops nor char formation was observed in either the atrium or the ventricle. ConclusionIn an in vivo swine heart model, DA with 4- to 6-second and 7- to 8-second intervals create deeper and wider lesions than does SA, suggesting its potential for clinical application in areas with thicker myocardial walls. However, DA with very short intervals may still pose a risk of excessive tissue heating.

Development of an enhanced electrical injera baking pan (Ethiopian Traditional mitad) using steel powder additives and gypsum insulation

Electric Injera baking Pan are prevalent in Ethiopia but are highly inefficient, resulting in significant heat loss, high energy consumption, and increased energy bills. This research investigates improving these devices using steel powder as an additive and gypsum as an insulator. The study examines thermal conductivity, baking time, energy consumption, heat loss, and insulation effectiveness. The objectives of this research are to improve the thermal conductivity of the baking surface while ensuring even heat distribution, enhance the insulation properties of the pan to reduce heat loss, improve the safety of the user by reducing the risk of excessive heat exposure to the outer surfaces, and reduce the overall energy consumption of the Injera baking process. Temperatures were measured using an infrared thermometer, digital thermometer, and thermocouple. Four samples (A0, A1, A2, & A3) with different steel powder compositions (0 %, 15 %, 25 %, and 35 %) and a constant 75 % clay soil composition were tested. The analysis showed an average baking energy of 0.45 kWh per kg of injera (0.198 kWh per injera) and a thermal efficiency of 86.4 % when baking 4.395 kg of injera. The total heat energy loss was 1402.78 KJ (14.08 % of 10300 KJ input energy). The losses were distributed among the retained (92.17 %), the baking plate (3.95 %), the bottom enclosure (2.08 %), the side enclosure (1.04 %), and the cover lid (0.76 %).

ОПРЕДЕЛЕНИЕ ТЕМПЕРАТУРЫ ЗУБЬЕВ ПИЛЫ ДЛЯ ТЕРМОФРИКЦИОННОГО РЕЗАНИЯ МЕТОДОМ КОМПЬЮТЕРНОГО МОДЕЛИРОВАНИЯ

In this study, the results of computer 3D modeling of the thermal friction process occurring between the teeth of a saw blade made of 50XGFA steel and a billet made of 45 steel are considered. The models were created using the SIMULIA/Abaqus software package to analyze temperature changes on the contacting surfaces of teeth and plates under plastic deformation conditions. As part of the work, various loads on the teeth and their effect on temperature parameters, heat generation and physical properties of materials are analyzed. As a result of the simulation, it was found that the optimal load for the teeth at plate temperatures from 400 to 600 ° C is 3.1 kN. This mode prevents excessive heating of the teeth, since their surface temperature does not exceed 650 ° C after passing 250 mm, the critical length of the contact zone during batch cutting.

Thermal Performance of Becool-Roof Coating in Reducing Heat Gain on Fisherman’s Settlement of Gorontalo City

Abstract Tanjung Kramat in Gorontalo, Indonesia is a village fostered by the department of Architecture, Universitas Negeri Gorontalo. The village is home to around two hundred families whose majority job is fishing. The people suffer from the uncomfortable condition of tropical coastal environment due to the high air temperature, humidity, and wind speed. Not to mention people in Gorontalo prefer to cover their upper structure using metal zincalume roof since they are more affordable. The highly thermal conductivity roof accounts for excessive heat gain to the house. Through a CSR program by Becool, the villagers received Cool Roof Coating to reduce heating and mitigate global warming. Before and after painting measurements of roof surface temperatures, radiant temperatures, and ground air temperatures are conducted. After the application of the coating, the analysis shows a positive result as the roof surface temperature is reduced by about 20ºC, followed by an improvement in ground air temperature by an average of 0.8ºC. The cool roof coating has succeeded in improving the neighborhood of Tanjung Kramat village.

Comprehensive analysis of thermal performance and low-grade energy charging efficiency of pipe-embedded building envelopes enhanced with single-level tree-shaped fin structures

Pipe-embedded walls (CnPWs) are structural and energy composite building components that can resist external disturbances by forming stealth thermal shielding layers. To tackle the mismatch between the heat charging rate and heat diffusion rate during energy charging processes, as well as the unsatisfactory robustness of stealth thermal shielding layers, the single-level tree-shaped metal finnd pipe-embedded walls (TfPWs) are proposed. To verify the effectiveness of TfPWs and obtain dynamic performances, a simulation study is conducted on 8 risk variables in 4 pairs through the validated numerical model. Results showed that the improved design was effective in obtaining more robust thermal shielding layers in auxiliary energy supply mode, the effect gained prominence as both the injection temperature and pipe spacing were augmented. In room heat load reduction mode, favorable benefits arise when pipe spacing exceeds 400 mm. The maximum increase rate of total injected energy under different reduction ratios of external insulation layer was 11.83%–31.91 %, while the maximum extra total heat loss was 5.33 %. Secondly, the trunk fins and branch fins played different roles in minimizing the excessive heat accumulation surrounding pipes, and the vertical and horizontal sizes of heat accumulation region mainly increased with the increase in trunk fin size and branch fin size respectively. Meanwhile, the utilization efficiency of fin material was higher when trunk fin size was smaller, and parameter combinations with trunk fin size of 0.2b and branch fin size of 0.4a/0.6a could achieve a better balance between material input and performance increase. Thirdly, the improvement effect of single left branch fin schemes was close to that of double branch fin schemes and significantly better than that of single right branch fin schemes. It was recommended to use single left branch fin schemes with an inclination angle of 60°. Finally, even if the reduction ratio of external insulation layer in different cities increased to 80 %, the inside surface temperature of TfPWs was still greater than room air. Taking CnPWs with standard external insulation layer as references, the TfPWs applied in Harbin, Beijing, and Shanghai could achieve similar or better results even when the reduction ratio of external insulation layer increased to 60 %, while TfPWs applied in Guangzhou could exhibit better performance even when the reduction ratio of external insulation layer increases to 80 %.

PI-SiO2 aerogel as a versatile high transparent material for photothermal cooperative management

Effectively insulating against excessive heat generated by sunlight while also avoiding harmful ultraviolet (UV) and maintaining suitable levels of visible light transparency is vital for minimizing energy consumption and optimizing sunlight utilization. To address the challenge of photothermal collaborative management, the PI consisted of high fluorinated dianhydride and aliphatic diamine was used to effectively improve the performance of SiO2 aerogels. The resulting PI-SiO2 aerogels retain the characteristics of SiO2 aerogels, such as low density, high transparency between 82∼89 %, and excellent thermal insulation properties with an ultralow thermal conductivity range from 0.023 W/(m.K) to 0.028 W/(m.K). Meanwhile, the coarsened skeleton of aerogels can withstand the extreme temperature difference between −196 ℃ and 200 ℃ without brittle fracture and yellowing. In addition, PI-SiO2 aerogels exhibit the capability to absorb a significant proportion of UV light within the 200–400 nm, offering distinct advantages in transparent thermal insulation materials. The multifunctional PI-SiO2 aerogels can be used as candidate materials in the fields of architecture, automobile, electronics, solar energy and aerospace.

Health impacts of excessive heat in Multnomah County, OR, 2021

Abstract Human-induced climate change is leading to increased extreme weather events, such as the heat dome that occurred in Multnomah County, OR, in June 2021. Certain groups are at increased risk from excessive heat events, such as the very young and very old, persons without stable housing, and persons with certain health comorbidities. Our review of three data sources (deaths, hospitalizations, and emergency department visits) showed large increases in all three measures in the summer of 2021. Further, two-thirds of identified heat deaths occurred in or near neighborhoods that ranked among the most vulnerable to extreme heat. Despite thoughtful planning, a recently updated heat response plan, and an unprecedented mobilization of resources, we documented severe health impacts due to this heat event. We recommend that local health jurisdictions and emergency responders increase readiness for such events by interrogating existing plans and tailoring them not to events of expected severity, but to a worst case scenario that exceeds historic experiences.

Monitoring the thermal state of an ingot with beveled and rounded corners in a slab crystallizer of a CCM

The organization of ingot cooling in the continuous caster mold affects the reliability, productivity and quality of the resulting ingots. Insufficient heat exchange between the solidifying metal and the wall of the mold leads to a decrease in the thickness of the solid shell of the ingot, which causes the formation of surface defects, and when the ingot is pulled out of the mold, emergency breakthroughs occur. Excessive heat transfer leads to an increase in the thickness of the solid shell, which entails excessive shrinkage of the ingot surface with the formation of a gap between the solid shell of the ingot and the walls of the mold. The appearance of an air gap leads to increased wear of the copper walls of the mold. There is a design of copper walls that makes it possible to reduce the normal component of forces that occurs during wear, reduce the temperature gradient and stress concentration in the corner of the ingot, and also bring the thickness of the hard crust stocking in the corner closer to the perimeter of the mold. However, the thermal state of the formed ingot with such a crystallizer design remains poorly understood. The goal of the work is to create a virtual tool for monitoring the operation of the mold of a slab continuous caster based on the development of a mathematical and computer model of the thermal state of an ingot with beveled and rounded corners. The temperature distribution in the ingot was calculated using the quasi-equilibrium theory of solidification. The numerical implementation of the mathematical model and obtaining an approximate solution using a computer were carried out using the finite dif-ference method and an implicit difference scheme. A computer program was developed in the Matlab development environment. Using computer modeling, the temperature distribution over the volume of the slab at the outlet of the mold with beveled and rounded corners was obtained. The program for the selected mold design allows you to analyze the solidification of the ingot skin and monitor this process for the selected steel grade and specified casting technological parameters

Therapeutic agents for Hailey-Hailey disease: A narrative review.

Hailey-Hailey disease (HHD) is an autosomal dominant genetic disorder of keratinocyte adhesion. It occurs due to mutations in ATP2C1, a gene on chromosome 3q21-24 which encodes human secretory pathway Ca2+/Mn2+ ATPase isoform 1, a calcium pump on the Golgi apparatus membrane. Recently, there has been a focus on certain pro-inflammatory cytokines such as IL-6 and IL-8 which play a role in HHD. Various triggers include excessive heat, menstruation, pregnancy, sweating, friction, exposure to sunlight and superficial infections. The therapy of the disorder is better understood by the varied pathogenetic steps and we aimed to comprehensively search for the various medical therapies used in HHD and align them with the existing knowledge on the pathogenesis and delineate them according to their major mode of action.

Strategic implementation of variable-thickness insulation layers for stratospheric airships

Excessive heat transfer from photovoltaic systems to airship hulls poses a threat to flight safety. To address this issue, a theoretical model was developed that combines thermal, heat transfer, and optimization models for airships with variable-thickness insulation layers. The study investigates the daily thermal behavior of stratospheric airships, focusing on the effects of thermal conductivity and insulation thickness. To balance weight reduction with insulation effectiveness, temperature constraints were used, and insulation thickness was optimized across different sections of the airship using a simulated annealing algorithm (SAA). Results indicate that adjusting thermal conductivity and insulation thickness can mitigate overheating and overpressure, albeit with a reduced solar energy output. Notably, variable-thickness insulation achieved a 9.7 % weight reduction at 40°N latitude, enhancing both photovoltaic system design and insulation material selection for stratospheric airships.