Excellent Mechanical Performance Research Articles

Investigation on the effects of deposition strategy on the mechanical characteristics and microstructure of austenitic stainless steel 308LSi manufactured via wire arc additive manufacturing

This study examines the impact of deposition strategy on ASS 308LSi thin-walled structure manufactured via the Wire Arc Additive Manufacturing (WAAM) technique on the microstructural characteristics, tensile strength, microhardness, Charpy impact testing, and fracture morphology of the WAAM 308LSi. The analysis of the microstructure reveals that the deposition strategy promotes transitioning from columnar to equiaxed fine grain structure. The tensile strength results show that specimens with a 45° deposition strategy exhibit lower anisotropy and higher tensile properties compared to those with a 0° deposition strategy, with improvements of 33.1% in the transverse direction and 26.7% in the longitudinal deposition directions, respectively. The microhardness in WAAM SS308LSi demonstrates variations in the bottom, middle, and top regions, with the highest average value observed at a 45° deposition strategy (213.3 ± 6.5 HV, 201.1 ± 10.7 HV, and 191.5 ± 5.2 HV) as well. The impact testing results indicate that the highest absorbed energy occurs at a 45° deposition strategy, with 75 ± 4.2 J and 74 ± 4.0 J for the transverse and longitudinal directions, respectively. The fractures observed during testing exhibit ductile characteristics, with the presence of dimples and particles. This study demonstrates the significant potential of the 45° deposition strategy with the implementation of double-sided substrate deposition, resulting in a refined microstructure, nearly isotropic behavior, and excellent mechanical performance.

Effect of deep cryogenic treatment on microstructure and mechanical properties of Fe50Mn30Co10Cr10 high entropy alloy fabricated by laser metal deposition

As a typical additive manufacturing technology, laser metal deposition (LMD) has been widely used to process high entropy alloy (HEA). However, deposited products usually have poor mechanical properties. In this study, deep cryogenic treatment (DCT) is proposed to enhance the mechanical performance of the laser melting deposited Fe50Mn30Co10Cr10 high entropy alloy. The tensile strength, hardness and strength-plasticity product of the HEA after 48 h of immersion by DCT processing were 901 MPa, 286HV and 33.3 GPa%, respectively. Compared with the as-deposited state, the HCP ε phase content and tensile strength of the deep cryogenic treated (DCTed) sample increased by 2.2 times and 30.8 %, respectively, while the average grain size decreased by 58.0 %. Furthermore, the friction coefficient and wear rate of the DCTed samples reduced by 25.6 % and 30.3 %, respectively. The high temperature gradient soaking in liquid nitrogen induced dynamic recrystallization, refining the FCC γ grain structures in the HEA. Meanwhile, the samples contained more HCP ε phase due to the transformation-induced plasticity (TRIP) effect triggered by thermal stress. The results indicate that the effects of fine-grain strengthening and second-phase particle dispersion strengthening contribute to the excellent mechanical performance. DCT processing provides a simple and effective way for overcoming the strength-ductility trade-off in the additive manufactured Fe50Mn30Co10Cr10 HEA.

Convection Heat Transfer and Performance Analysis of a Triply Periodic Minimal Surface (TPMS) for a Novel Heat Exchanger

Heat exchangers are necessary in most engineering systems that move thermal energy from a hot source to a colder location. The development of additive manufacturing technology facilitates the design and optimization of heat exchangers by introducing triply periodic minimal surface (TPMS) structures. TPMSs have shown excellent mechanical and thermal performance, which can improve heat energy transfer efficiency in heat exchangers. This current study intends to design and develop efficient, lightweight heat exchangers for aerospace and space applications. Using the TPMS structure, a porous construction encloses a horizontal tube that circulates heated fluid. Low-temperature water circulates inside a rectangular box that houses the complete system to remove heat from the horizontal pipe. Three porous structures, the gyroid, diamond, and FKS structures, were employed and examined. Porous models with various porosities and surface areas (15 cm2 and 24 cm2) were investigated. The results revealed that the gyroid structure exhibits the highest Nusselt number for heat removal (Nu max = 2250), confirming the highest heat transfer and lowest pressure drop among the three structures under investigation. The maximum Nusselt number obtained for the FKS structure is less than 1000, whereas, for the diamond structure, it is near 1250. A linear variation in the average Nusselt number as a function of the structure surface area was found for the FKS and diamond structures. In contrast, nonlinearity was observed in the gyroid structures.

Influence of overlap rate and ultrasonic compaction on mechanical performance for additive manufacturing of continuous carbon fiber reinforced polylactic acid composites

The additive manufacturing (AM) technology of continuous fiber reinforced thermoplastic composites (CFRTPCs) is gaining attention in the composites industry due to its excellent mechanical performance, potential designability and light-weight structures. Process parameters of AM have a significant impact on mechanical performance and forming accuracy. There is still a Lack of clear design basis for hatch spacing as structural parameter. This study focused on the effect of overlap rate on AM performance of continuous carbon fiber (CCF)/polylactic acid (PLA) composites through the mechanical test, surface morphology, defects characterization and failure analysis, and investigated the adaptability of ultrasonic compaction post-treatment to overlap rate settings. The results indicated that proper overlap state between filaments was beneficial for mechanical properties. The optimal interlaminar shear strength (ILSS) increased to 22.72 MPa by 56 % and tensile strength improved by 17.5 % to 721.65 MPa at various overlap rates. Surface roughness remained stable at approximately 33 μm. Ultrasonic compaction achieved a maximum ILSS up to 24.84 MPa with improvement of 10.26 %, and tensile strength reached to 736.76 MPa with 2.09 % improvement, showing excellent adaptability to overlap rate design. Research findings will improve understanding of digital adjustment mechanisms for printing parameters and provide design guidance for high-performance AM technology of CFRTPCs.

Investigation on mechanical and tribological properties of PTFE nanocomposites reinforced by surface-modified graphene using molecular dynamics simulations

Surface-modified nanoparticles are commonly used to improve the mechanical properties and wear resistance of polytetrafluoroethylene (PTFE). However, fewer studies have been devoted to quantitatively revealing the action mechanism of graphene (Gr) modified with different functional groups on the mechanical and tribological properties of PTFE. Herein, the effects of four functional groups (−OH, −NH2, −COOH, and −COOCH3 functional groups) on the surface of Gr nanosheets on the mechanical and tribological properties of PTFE nanocomposites are studied using molecular dynamics simulations. The results indicate that the incorporation of functional groups to the Gr surface is able to significantly improve the mechanical properties and wear resistance of the nanocomposites, and the COOH-functionalized Gr nanosheet shows the best reinforcing effect due to the synergistic effect of its own high surface roughness and strong interfacial interaction between itself and the matrix. It is also found that the friction coefficient of the nanocomposites is obviously increased by the inclusion of functionalized Gr nanosheets, and the greater the surface roughness of the functionalized Gr nanosheet, the more significant the growth of the friction coefficient of the nanocomposites. The pull-out test and confined shear simulation reveal that due to the increased interfacial shear strength and the isolation of functional groups, an inhomogeneous transfer film is formed at the friction interface, leading to a decreased anti-friction property. This study provides some guidance for the future design and development of polymer nanocomposites with excellent mechanical and tribological performance for use in extreme service conditions.

Precision depth-controlled isolated silver nanoparticle-doped diamond-like carbon coatings with enhanced ion release, biocompatibility, and mechanical performance

Silver doped diamond-like carbon (Ag/DLC) coatings are in high demand for biomedical applications such as artificial implants, surgical instruments, and medical devices. However, recent reports indicate that the excess Ag concentration required in typically made Ag/DLC coatings significantly reduces their mechanical performance and biocompatibility. Here, we propose a novel single-step approach to precisely dope small quantities of Ag in the form of isolated nanoparticles embedded at defined depths in a DLC matrix. This new Ag/DLC coating architecture is designed to release controlled Ag ion levels to fight infection in the early post-surgery stages, while a confined Ag amount maintains the excellent mechanical and biocompatibility performance of the underlying DLC coating when compared to typically made Ag/DLC coating designs. Coatings of pure DLC, typically made Ag/DLC with Ag doped throughout the carbon matrix and the new Ag/DLC design with precise Ag doping, are made using a modified magnetron sputtering system. The coatings are characterised for structural, mechanical, ion leaching, and biocompatibility profiles against L929 fibroblast cells. Results indicate that the new Ag/DLC coating requires only 2 at.% Ag to release a similar level of Ag ions (∼0.6 ppm) to a typical Ag/DLC coating with a much higher Ag content of 17 at.%. The new Ag/DLC coating design also outperforms the typical design with a 63 % increase in hardness, 100 % higher Young's modulus, and 21 % higher biocompatibility. The enhanced biomechanical performance of the proposed new Ag/DLC architecture could have significant potential for coating of future medical devices.

Room-Temperature, Solution-Processed, Robust, Transparent, and Conductive SiOx/AgNW Nanocomposite Coating.

AgNW networks show high promise as a conductive material due to excellent flexibility, low resistance, high transparency, and ease of large-scale preparation. However, the application of AgNW networks has been hindered by their inherent characteristics, such as easy oxidation degradation, chemical corrosion, and structural instability at high temperatures. In this study, a dense SiOx protective layer derived from perhydropolysilazane was introduced to fabricate a robust SiOx/AgNW nanocomposite coating through an all-solution process at room temperature. The achieved nanocomposite coating shows outstanding thermal stability up to 450 °C, resistance to ultraviolet radiation, and excellent mechanical performance by maintaining stability after 10,000 cycles of bending at a radius of 2.5 mm, 1000 cycles of peeling, and 1200 cycles of wearing. Meanwhile, the nanocomposite coating demonstrates exceptional chemical tolerance against HCl, Na2S, and organic solvents. A transparent heater based on the nanocomposite coating achieves a remarkable benchmark with a maximum temperature of 400 °C at 20 V. These features highlight the potential of the nanocomposite coating in flexible electronics, optoelectronics, touch screens, and high-performance heaters.

Free-space direct nanoscale 3D printing of metals and alloys enabled by two-photon decomposition and ultrafast optical trapping.

Nanoscale three-dimensional (3D) printing of metals and alloys has faced challenges in speed, miniaturization and deficiency in material properties. Traditional nanomanufacturing relies on lithographic methods with material constraints, limited resolution and slow layer-by-layer processing. This work introduces polymer-free techniques using two-photon decomposition and optical force trapping for free-space direct 3D printing of metals, metal oxides and multimetallic alloys with resolutions beyond optical limits. This method involves the two-photon decomposition of metal atoms from precursors, rapid assembly into nanoclusters via optical forces and ultrafast laser sintering, yielding dense, smooth nanostructures. Enhanced near-field optical forces from laser-induced localized surface plasmon resonance facilitate nanocluster aggregation. Our approach eliminates the need for organic materials, layer-by-layer printing and complex post-processing. Printed Mo nanowires show an excellent mechanical performance, closely resembling the behaviour of single crystals, while Mo-Co-W alloy nanowires outperform Mo nanowires. This innovation promises the customizable 3D nanoprinting of high-quality metals and metal oxides, impacting nanoelectronics, nanorobotics and advanced chip manufacturing.

Self-Adhesive, Stretchable, and Thermosensitive Iontronic Hydrogels for Highly Sensitive Neuromorphic Sensing-Synaptic Systems.

Artificial sensory afferent nerves that emulate receptor nanochannel perception and synaptic ionic information processing in chemical environments are highly desirable for bioelectronics. However, challenges persist in achieving life-like nanoscale conformal contact, agile multimodal sensing response, and synaptic feedback with ions. Here, a precisely tuned phase transition poly(N-isopropylacrylamide) (PNIPAM) hydrogel is introduced through the water molecule reservoir strategy. The resulting hydrogel with strongly cross-linked networks exhibits excellent mechanical performance (∼2000% elongation) and robust adhesive strength. Importantly, the hydrogel's enhanced ionic conductance and heterogeneous structure of the temperature-sensitive component enable highly sensitive strain information perception (GFmax = 7.94, response time ∼ 87 ms), temperature information perception (TCRmax = -1.974%/°C, response time ∼ 270 ms), and low energy consumption synaptic plasticity (42.2 fJ/spike). As a demonstration, a neuromorphic sensing-synaptic system is constructed integrating iontronic strain/temperature sensors with fiber synapses for real-time information sensing, discrimination, and feedback. This work holds enormous potential in bioinspired robotics and bioelectronics.

A synergistic enhancement strategy for mechanical and conductive properties of hydrogels with dual ionically cross-linked κ-carrageenan/poly(sodium acrylate-co-acrylamide) network

Applying conductive hydrogels in electronic skin, health monitoring, and wearable devices has aroused great research interest. Yet, it remains a significant challenge to prepare conductive hydrogels simultaneously with superior mechanical, self-recovery, and conductivity performance. Herein, a dual ionically cross-linked double network (DN) hydrogel is fabricated based on K+ and Fe3+ ion cross-linked κ-carrageenan (κ-CG) and Fe3+ ion cross-linked poly(sodium acrylate-co-acrylamide) P(AANa-co-AM). Benefiting from the abundance of hydrogen bonds and metal coordination bonds, the conductive hydrogel has excellent mechanical properties (fracture strain up to 1420 %, fracture stress up to 2.30 MPa, and toughness up to 20.63 MJ/m3) and good self-recovery performance (the recovery rate of the toughness can reach 85 % after waiting for 1 h). Meanwhile, due to the introduction of dual metal ions of K+ and Fe3+, the ionic conductivity of conductive hydrogel is up to 1.42 S/m. Furthermore, the hydrogel strain sensor has good sensitivity with a gauge factor (GF) of 2.41 (0–100 %). It can be a wearable sensor that monitors different human motions, such as sit-ups. This work offers a new synergistic strategy for designing a hydrogel strain sensor with high mechanical, self-recovery, and conductive properties.

Mechanically customizable lignin bio-elastomers based on tailorable multiscale microstructures

The development of bio-based polyurethanes (PU) elastomers with well-designed multiscale microstructures to customize their mechanical performances was desired, but remained an ongoing challenge. Herein, a novel strategy of integrating tailorable hard-soft nanophases with multiple hydrogen bond (H-bond) interactions was proposed to construct mechanically customizable PU bio-elastomers. In this strategy, highly reactive lignin with high hydroxyl contents was employed as bio-polyol monomer reacting with hexamethylene diisocyanate (HDI) to construct carbamate bonds with a function of tailoring H-bond degree via altering the feeding ratio of lignin. The rigid lignin cooperating with HDI as hard segments self-assembled to generate phase separated nanostructures. Consequently, the integration of well-defined hard-soft nanophases and multiple H-bond interactions in the synthesized lignin-based PU (LPU) achieved excellent and customizable mechanical performances ranging from highly elastic rubber to highly stiff plastic with ultrahigh strength of 72.8 MPa and unprecedented modulus of 3.5 GPa. Impressively, rubber-like LPU elastomers could recover 90 % of initial stress even after 500 stretching cycles, indicating fascinating resilience and fatigue resistance. More especially, rigid LPU plastics with fully hard domains and dense H-bond networks could be transformed into flexible and bendable paper-like elastomers once eliminating intermolecular H-bond interactions under 60 °C hot water. Thus, this work provides a feasible and promising approach to construct supramolecular PU elastomers with excellent and customizable mechanical performances to extend their on-demand applications.

Experimental and numerical investigation on the combustion behavior of densified wood: Differences among wood species and impact of char oxidation

Densified wood (DW) is a novel structural material with promissing application potential in construction industry due to its excellent mechanical performance. However, it could also be a disastrous fuel contributing to the development of fires. This work experimentally and numerically investigated the combustion behavior of DW. The differences among wood species (fir, pine and oak) and their char oxidation impacts are emphasized. The experimental results indicate that DW has a 44.7 K lower pyrolysis peak temperature on average, a 32.2 % lower peak mass loss rate, and a 8 % higher residual mass ratio than natural wood (NW) in N2 due to the delignification process. The hemicellulose and cellulose pyrolysis are endothermic in N2 but exothermic in air. Wood pyrolysis has an additional char oxidation reaction in air. The higher density of DW leads to longer times for ignition and flaming combustion. DW presents a higher heat release rate and average 4.7 MJ kg−1 higher effective heat of combustion of char. Two parallel pyrolysis reaction schemes based on ambiance are proposed, which well-predict the microscale characterizations but fail to represent the combustion behavior. An optimized mode was developed by adding a continuous char oxidation reaction to the N2 reaction scheme, which best predicts the combustion behaviors.

Enhanced mechanical property and flame resistance of phosphorylated cellulose nanofiber based‐aerogel combined with boric acid

AbstractAs for cellulose‐based aerogels, a feature of inadequate mechanics and easy‐flammability seriously restricts their practical applications. To address this issue, herein a lightweight, mechanical elastic and flame‐retardant phosphorylated lignin‐based cellulose nanofiber (PLCNF‐B) aerogel with the aid of boric acid was successfully obtained by freeze‐drying method. Due to the uniform and tough network structure benefitting by strong hydrogen bond between phosphorylated fibers and boric acid, the resultant aerogel showed excellent mechanical performance, that is, high compressive strength of 8.9 kPa (strain: 50%) and outstanding cyclic reliability (remain 90% after 10 cycles). Meanwhile, PLCNF‐B aerogel possesses highly improved flame‐retardant property, that is, a high LOI value (up to 46%), significantly reduced peak heat release rate (11.2 W/g) and total heat release rate (0.47 kJ/g). Based on structural observation and analysis, the flame‐retardant behavior should be attributed to the formation of PxOy/amorphous boron oxide protective layer, which is derived from the phosphorus containing group of PLCNF and boric acid. The splendid overall performance of aerogel material offers a potential material tactic for design and development of advanced bio‐based aerogels for practical applications.

Stiff gel-protected fiber-shaped supercapacitors based on CNFA/silk composite fiber with superhigh interference-resistant ability as self-powered temperature sensor

The development of self-powered sensors with interference-resistant detection is a priority area of research for the next generation of wearable electronic devices. Nevertheless, the presence of multiple stimuli in the actual environment will result in crosstalk with the sensor, thereby hindering the ability to obtain an accurate response to a singular stimulus. Here, we present a self-powered sensor composed of silk-based conductive composite fibers (CNFA@ESF), which is capable of energy storage and sensing. The fabricated CNFA@ESF exhibits excellent mechanical performance, as well as flexibility that can withstand various deformations. The CNFA@ESF provides a good areal capacitance (44.44 mF cm−2), high-rate capability, and excellent cycle stability (91 % for 5000 cycles). In addition, CNFA@ESF also shows good sensing performance for multiple signals including strain, temperature, and humidity. It was observed that the assembly of the symmetrical device with a stiff hydrogel surface layer for protection enabled the real-time, interference-free monitoring of temperature signals. Also, the CNFA@ESF can be woven into fabrics and integrated with a solar cell to form a self-powered sensor system, which has been proven to convert and store solar energy to power electronic watches, indicating its huge potential for future wearable electronics.

Blast resistance of 3D-printed Bouligand concrete panels reinforced with steel fibers: Numerical investigations

3D-printed concrete structures inspired by Bouligand architecture with helically twisted sequences exhibit excellent mechanical performance owing to its aligned fiber orientation. In this study, 3D-printed concrete panels with different numbers of layers (five, ten, and 15 layers) and spiral angles (0°, 15°, 30°, and 45°) are designed for numerical investigations of their blast-resistant capacity. A multi-scale model is developed to capture the isotropic and anisotropic properties of the fiber-concrete composite. The adequacy and accuracy of the model are evaluated and validated by experimental data in the literature. Blast resistance of different types of panels in terms of time histories of central-point deflection, contact explosion-induced plastic dissipation energy, stress propagation, and principal stress distribution is examined. It is found that extrusion-based concrete panels with aligned fiber orientation substantially enhance the blast resistance compared to traditional cast concrete panels with random fiber orientation. Furthermore, more layers of printed concrete panels prove to be more efficient in filtering blast waves. In particular, shifting a pitch angle of 30° after printing each layer plays an important role in reducing the maximum deflection. Meanwhile, 3D-printed concrete panels with a pitch angle of 0° can better mitigate blast-induced damage. Through parametric studies, the intrinsic mechanism of steel fibers aligned in 3D-printed panels is numerically analyzed to support the conclusions.

(Battery Student Slam 8 Award Winner) A Simple and Fast Method to Assemble Flexible and Stable Quasi-Solid-State Zn Ion Pouch Cell

Aqueous zinc-ion batteries (AZIBs) have been investigated intensively as effective energy storage devices that are environmentally friendly, safe, and have a lower cost than current Li-ion batteries.[1-5] Being outstandingly safe due to usage of non-organic electrolyte, AZIBs could also be used as power supply for wearable electronics. This also put high standard requirements in terms of flexibility, stability and electrochemical performance to AZIBs. On the other hand, the general challenges, such as the formation of the dendrites on the Zn anodes, hydrogen evolution and side reactions, have been obstructing the practical application of AZIBs. In this presentation, a simple method to assemble quasi-solid-state Zn ion pouch cell with excellent mechanical performance, flexibility and electrochemical performance was developed, combining in-situ electrodeposition of MnO2 cathode and aramid nano fiber-based hydrogel with Zn plate as anode. In-situ and cycling measurements of the electrodeposition of MnO2 on carbon nanotube mat shows excellent capacitance and superior cycling stability. In addition, Kevlar derivatized aramid nanofiber-based hydrogel shows extremely strong strength when combined with polyvinyl alcohol, which prolonged the lifetime of the cell by preventing Zn dendrite growth largely.[5,6] Moreover, the method to assemble the AZIBs pouch cell enables us to optimize the process, decrease the steps, and save time effectively by taking advantage of hydrogel formation stage and avoiding conventional verbose slurry-casting-drying steps. This work paves an efficient path to assemble flexible and stable AZIBs pouch cells with high capacity and cycling stability.[1] Tang, Boya, et al. "Issues and opportunities facing aqueous zinc-ion batteries." Energy & Environmental Science 12.11 (2019): 3288-3304.[2] Li, Chang, et al. "Toward practical aqueous zinc-ion batteries for electrochemical energy storage." Joule 6.8 (2022): 1733-1738.[3] Yu, Feng, et al. "An aqueous rechargeable zinc-ion battery on basis of an organic pigment." Rare Metals 41.7 (2022): 2230-2236.[4] Lin, Yuexing, et al. "Dendrite-free Zn anode enabled by anionic surfactant-induced horizontal growth for highly-stable aqueous Zn-ion pouch cells." Energy & Environmental Science 16.2 (2023): 687-697.[5] Wang, Peng, and Petru Andrei. "High Performance Separator and Hydrogel Based on Aramid Fibers for Zn Ion Batteries." Electrochemical Society Meeting s 242. No. 4. The Electrochemical Society, Inc., 2022.[6] Xu, Lizhi, et al. "Water‐rich biomimetic composites with abiotic self‐organizing nanofiber network." Advanced Materials 30.1 (2018): 1703343.

Efficient Zn-Ion Pouch Cell Assembling Based on Aramid Nanofiber Hydrogel

With the fast advancement of portable and wearable electronics, it is urgent to develop safe, stable and flexible power supply devices. Safe and environmentally friendly aqueous zinc-ion batteries (AZIBs) have a low-cost and are perfect candidates for energy storage device in such applications [1-4]. Giving the general challenges, such as the formation of the dendrites on the Zn anodes and hydrogen evolution and side reactions, extensive and wide research has focused on building stable AZIBs with high performance, but less attention was paid to making Zn ion pouch cells which are flexible and with high capacity In this presentation, we developed an efficient method to assemble Zn-ion pouch cells based on the process of formation of the aramid nanofiber hydrogel. The method involves the dipping precursor solution, solvent exchanging, and in-situ electrodeposition of MnO2. The assembled Zn-ion pouch cells exhibit excellent mechanical performance, flexibility and electrochemical performance, which are ideal for portable and wearable electronics. Based on this method, we successfully assembled 3-layer (cathode/anode/cathode, A/C/A) and 5 layer (A/C/A/C/A) pouch cells with over 100 times higher capacity compared with coin cell. In addition, the pouch cell with aramid nanofiber hydrogel and in-situ electrodeposited MnO2 cathode on carbon nanotube mat demonstrates superior cycling stability [5,6]. More details about our assembling method for flexible and stable pouch cells for AZIBs and experimental measurements related to the cycling and stability characteristics, will be presented at the meeting.[1] Yu, Peng, et al. "Flexible Zn‐ion batteries: recent progresses and challenges." Small 15.7 (2019): 1804760.[2] Li, Yingbo, et al. "Recent advances in flexible zinc‐based rechargeable batteries." Advanced Energy Materials 9.1 (2019): 1802605.[3] Li, Chunyang, et al. "High-rate and high-voltage aqueous rechargeable zinc ammonium hybrid battery from selective cation intercalation cathode." ACS Applied Energy Materials 2.10 (2019): 6984-6989.[4] Yu, Feng, et al. "Aqueous alkaline–acid hybrid electrolyte for zinc-bromine battery with 3V voltage window." Energy Storage Materials 19 (2019): 56-61.[5] Wang, Peng, and Petru Andrei. "High Performance Separator and Hydrogel Based on Aramid Fibers for Zn Ion Batteries." Electrochemical Society Meeting s 242. No. 4. The Electrochemical Society, Inc., 2022.[6] Xu, Lizhi, et al. "Water‐rich biomimetic composites with abiotic self‐organizing nanofiber network." Advanced Materials 30.1 (2018): 1703343.

Mesoporous NiMoO4 nanorod electrode materials for flexible and asymmetric energy storage devices.

Recently, ternary metal oxides as cathode materials have been the focus of research into supercapacitors owing to their high power density and cost-efficient features. The development of excellent electrode materials is the key to improving supercapacitor total performance. Herein, we report several kinds of NiMoO4 nanostructures grown on nickel foam using a simple hydrothermal strategy. The assembled hybrid devices show an energy density of 35.9 W h kg-1 at a power density of 2708 W kg-1. After repeated charging and discharging cycling and bending tests, they show excellent durability performance and mechanical stability performance.

Covalent adaptable polymer networks with CO2-facilitated recyclability

Cross-linked polymers with covalent adaptable networks (CANs) can be reprocessed under external stimuli owing to the exchangeability of dynamic covalent bonds. Optimization of reprocessing conditions is critical since increasing the reprocessing temperature costs more energy and even deteriorates the materials, while reducing the reprocessing temperature via molecular design usually narrows the service temperature range. Exploiting CO2 gas as an external trigger for lowering the reprocessing barrier shows great promise in low sample contamination and environmental friendliness. Herein, we develop a type of CANs incorporated with ionic clusters that achieve CO2-facilitated recyclability without sacrificing performance. The presence of CO2 can facilitate the rearrangement of ionic clusters, thus promoting the exchange of dynamic bonds. The effective stress relaxation and network rearrangement enable the system with rapid recycling under CO2 while retaining excellent mechanical performance in working conditions. This work opens avenues to design recyclable polymer materials with tunable dynamics and responsive recyclability.

High‐Specific‐Energy Self‐Supporting Cathodes for Flexible Energy Storage Devices: Progress and Perspective

AbstractThe development of flexible electronics technology has led to the creation of flexible energy storage devices (FESDs). In recent years, flexible self‐supporting cathodes have gained significant attention due to their high energy density, excellent mechanical performance, and strong structural plasticity among various cathode materials. Flexible self‐supporting cathodes enable larger active material loading capacity and conductive networks for electrodes, thereby perfectly meeting the mechanical and electrochemical performance requirements of FESDs. Currently, the focus of flexible self‐supporting cathodes lies in exploring flexible substrates or novel binders to enhance the flexibility of conventional cathode materials. However, the flexibility of cathode poses challenges as they are primarily composed of transition metal oxides, resulting in limited research on their flexibility. A comprehensive review and prospective analysis are of utmost importance to effectively advance the progress of flexible self‐supporting cathodes and propel their development forward. Herein, the present discourse delves into the latest advancements concerning flexible self‐supporting cathode, focusing on synthesis methodologies, structural design approaches, and characterization parameters. Examining the current progress, the inherent advantages, existing challenges, and potential prospects of these materials are comprehensively elucidated and emphasized.