ESA Climate Change Initiative Research Articles

Soil Moisture Mapping from Satellites: An Intercomparison of SMAP, SMOS, FY3B, AMSR2, and ESA CCI over Two Dense Network Regions at Different Spatial Scales

A good knowledge of the quality of the satellite soil moisture products is of great importance for their application and improvement. This paper examines the performance of eight satellite-based soil moisture products, including the Soil Moisture Active Passive (SMAP) passive Level 3 (L3), the Soil Moisture and Ocean Salinity (SMOS) Centre Aval de Traitement des Données SMOS (CATDS) L3, the Japan Aerospace Exploration Agency (JAXA) Advanced Microwave Scanning Radiometer 2 (AMSR2) L3, the Land Parameter Retrieval Model (LPRM) AMSR2 L3, the European Space Agency (ESA) Climate Change Initiative (CCI) L3, the Chinese Fengyun-3B (FY3B) L2 soil moisture products at a coarse resolution of ~0.25°, and the newly released SMAP enhanced passive L3 and JAXA AMSR2 L3 soil moisture products at a medium resolution of ~0.1°. The ground soil moisture used for validation were collected from two well-calibrated and dense networks, including the Little Washita Watershed (LWW) network in the United States and the REMEDHUS network in Spain, each with different land cover. The results show that the SMAP passive soil moisture product outperformed the other products in the LWW network region, with an unbiased root mean square (ubRMSE) of 0.027 m3 m−3, whereas the FY3B soil moisture performed the best in the REMEDHUS network region, with an ubRMSE of 0.025 m3 m−3. The JAXA product performed much better at 0.25° than at 0.1°, but at both resolutions it underestimated soil moisture most of the time (bias < −0.05 m3 m−3). The SMAP-enhanced passive soil moisture product captured the temporal variation of ground measurements well, with a correlation coefficient larger than 0.8, and was generally superior to the JAXA product. The LPRM showed much larger amplitude and temporal variation than the ground soil moisture, with a wet bias larger than 0.09 m3 m−3. The underestimation of surface temperature may have contributed to the general dry bias found in the SMAP (−0.018 m3 m−3 for LWW and 0.016 m3 m−3 for REMEDHUS) and SMOS (−0.004 m3 m−3 for LWW and −0.012 m3 m−3 for REMEDHUS) soil moisture products. The ESA CCI product showed satisfactory performance with acceptable error metrics (ubRMSE < 0.045 m3 m−3), revealing the effectiveness of merging active and passive soil moisture products. The good performance of SMAP and FY3B demonstrates the potential in integrating them into the existing long-term ESA CCI product, in order to form a more reliable and useful product.

Comparing soil moisture anomalies from multiple independent sources over different regions across the globe

Abstract. Agricultural drought events can affect large regions across the world, implying the need for a suitable global tool for an accurate monitoring of this phenomenon. Soil moisture anomalies are considered a good metric to capture the occurrence of agricultural drought events, and they have become an important component of several operational drought monitoring systems. In the framework of the JRC Global Drought Observatory (GDO, http://edo.jrc.ec.europa.eu/gdo/), the suitability of three datasets as possible representations of root zone soil moisture anomalies has been evaluated: (1) the soil moisture from the Lisflood distributed hydrological model (namely LIS), (2) the remotely sensed Land Surface Temperature data from the MODIS satellite (namely LST), and (3) the ESA Climate Change Initiative combined passive/active microwave skin soil moisture dataset (namely CCI). Due to the independency of these three datasets, the triple collocation (TC) technique has been applied, aiming at quantifying the likely error associated with each dataset in comparison to the unknown true status of the system. TC analysis was performed on five macro-regions (namely North America, Europe, India, southern Africa and Australia) detected as suitable for the experiment, providing insight into the mutual relationship between these datasets as well as an assessment of the accuracy of each method. Even if no definitive statement on the spatial distribution of errors can be provided, a clear outcome of the TC analysis is the good performance of the remote sensing datasets, especially CCI, over dry regions such as Australia and southern Africa, whereas the outputs of LIS seem to be more reliable over areas that are well monitored through meteorological ground station networks, such as North America and Europe. In a global drought monitoring system, the results of the error analysis are used to design a weighted-average ensemble system that exploits the advantages of each dataset.

Constraining a terrestrial biosphere model with remotely sensed atmospheric carbon dioxide

We present two novel earth observation products derived from the BESD and EMMA XCO2 products which were respectively retrieved from SCIAMACHY and GOSAT observations within the GreenHouse Gas project of ESA's Climate Change Initiative (GHG-CCI). These products are inferred by a Carbon Cycle Data Assimilation System (CCDAS) and consist of net and gross biosphere-atmosphere fluxes of carbon dioxide on a global 0.5° grid. As a further dataset provided by the CCI, the burnt area product developed by its Fire忌i project was used in the CCDAS to prescribe the emission component from biomass burning. The new flux products are provided with per-pixel uncertainty ranges. Fluxes with uncertainty ranges can also be provided aggregated in space and time, e.g. over given regions or as annual means. For both, posterior flux fields inferred from BESD and EMMA products, transport model simulations show reasonable agreement with the atmospheric carbon dioxide concentration observed at flask sampling stations. This means that the information provided by the terrestrial and transport models, the respective GHG ECV product, the burnt area ECV product, a product of the Fraction of Absorbed Photosynthetically Active Radiation used to drive the model, and the atmospheric flask samples is largely consistent.The most prominent feature in the posterior net flux is the tropical source of CO2 inferred from both products. But for the EMMA product this release, especially over South America, is with 300gC/m2/year much more pronounced than for BESD. This confirms findings by a recent intercomparison of transport inversions using GOSAT data by Houweling et al. (2015). The reason for the larger net flux is increased heterotrophic respiration. For both products the posterior 2010 sink over Europe (without Russia) is in the range of a recent compilation of European flux estimates by Reuter et al. (2016b). The posterior 2010 uptake of Australia (including Oceania) inferred from the EMMA product is 1.3 ± 0.2PgC/year and appears to confirm the high sink also derived from GOSAT by Detmers et al. (2015) over a slightly different period and area. While for some regions (USA, Canada, Europe, Russia, Asia) the one standard deviation uncertainty ranges derived from BESD and EMMA do overlap, for some other regions (Brazil, Africa, Australia) this is not the case. It is not clear yet whether this is due to the uncertainty specifications in the respective products or the handling of uncertainty in the assimilation chain. Assumptions on correlation of observational uncertainty in space and time have a considerable impact on the inferred flux fields (≈ 60gC/m2/year). The effect of adding an uncertainty that approximates the error in the retrieval system is of similar size.

The ESA Climate Change Initiative (CCI): A European contribution to the generation of the Global Climate Observing System

The Earth System behaves as a highly coupled system comprising physical, chemical, biological, and anthropogenic components and processes with complex interactions and feedbacks between them. Climate change is arguably the greatest challenge to balance in the Earth system. The Paris Agreement (UNFCCC, 2016) recognised the need to reduce the risks from and impacts of climate change and called for the increase in the global average temperature to be held well below 2°C above pre-industrial levels, with the ideal aim being to limit it to 1.5°C. The UN Framework Convention on Climate Change (UNFCCC) agreement is based on the evidence for, and likely causes of, climate change synthesised by the Intergovernmental Panel on Climate Change (IPCC) and is supported, for climate, by the Global Climate Observing System (GCOS). GCOS has defined a set of Essential Climate Variables (ECV), established the requirements for their systematic observation, and the development of data archives, needed to support the study the climate system. The Climate Change Initiative (CCI), represents the contribution by the European Space Agency (ESA) to GCOS. CCI is a programme designed to bring together European expertise in Earth Observation with that from the climate research community to address those ECV that can be generated using satellite observations. Specifically the objective is ‘to realise the full potential of the long-term global Earth Observation archives that ESA together with its Member States have established over the last thirty years, as a significant and timely contribution to the ECV databases required by the United Nations Framework Convention on Climate Change (UNFCCC)’. In doing so the intended legacy of the programme is to put in place mechanisms capable of providing long term, fully traceable, and transparent access to its records. This paper provides an overview of the CCI Programme and highlights a few of its achievements to date.

ESA CCI Soil Moisture for improved Earth system understanding: State-of-the art and future directions

Climate Data Records of soil moisture are fundamental for improving our understanding of long-term dynamics in the coupled water, energy, and carbon cycles over land. To respond to this need, in 2012 the European Space Agency (ESA) released the first multi-decadal, global satellite-observed soil moisture (SM) dataset as part of its Climate Change Initiative (CCI) program. This product, named ESA CCI SM, combines various single-sensor active and passive microwave soil moisture products into three harmonised products: a merged ACTIVE, a merged PASSIVE, and a COMBINED active+passive microwave product. Compared to the first product release, the latest version of ESA CCI SM includes a large number of enhancements, incorporates various new satellite sensors, and extends its temporal coverage to the period 1978–2015. In this study, we first provide a comprehensive overview of the characteristics, evolution, and performance of the ESA CCI SM products. Based on original research and a review of existing literature we show that the product quality has steadily increased with each successive release and that the merged products generally outperform the single-sensor input products. Although ESA CCI SM generally agrees well with the spatial and temporal patterns estimated by land surface models and observed in-situ, we identify surface conditions (e.g., dense vegetation, organic soils) for which it still has large uncertainties. Second, capitalising on the results of >100 research studies that made use of the ESA CCI SM data we provide a synopsis of how it has contributed to improved process understanding in the following Earth system domains: climate variability and change, land-atmosphere interactions, global biogeochemical cycles and ecology, hydrological and land surface modelling, drought applications, and meteorology. While in some disciplines the use of ESA CCI SM is already widespread (e.g. in the evaluation of model soil moisture states) in others (e.g. in numerical weather prediction or flood forecasting) it is still in its infancy. The latter is partly related to current shortcomings of the product, e.g., the lack of near-real-time availability and data gaps in time and space. This study discloses the discrepancies between current ESA CCI SM product characteristics and the preferred characteristics of long-term satellite soil moisture products as outlined by the Global Climate Observing System (GCOS), and provides important directions for future ESA CCI SM product improvements to bridge these gaps.

Stratospheric aerosol data records for the climate change initiative: Development, validation and application to chemistry-climate modelling

This paper presents stratospheric aerosol climate records developed in the framework of the Aerosol_cci project, one of the 14 parallel projects from the ESA Climate Change Initiative. These data records were processed from a stratospheric aerosol dataset derived from the GOMOS experiment, using an inversion algorithm optimized for aerosol retrieval, called AerGOM. They provide a suite of aerosol parameters, such as the aerosol extinction coefficient at different wavelengths in the UV–visible range. The extinction record includes the total extinction as well as separate fields for liquid sulfate aerosols and polar stratospheric clouds (PSCs). Several additional fields (PSC flag, etc.) are also provided. The resulting stratospheric aerosol dataset, which spans the whole duration of the GOMOS mission (2002−2012), was validated using different reference datasets (lidar and balloon profiles).In the present paper, the emphasis is put on the extinction records. After a thorough analysis of the original AerGOM dataset, we describe the methodology used to construct the gridded CCI-GOMOS dataset and the resulting improvements on both the AerGOM algorithm and the binning procedure, in terms of spatio-temporal resolution, coverage and data quality.The extinction datasets were validated using lidar profiles from three ground-based stations (Mauna Loa, Garmisch-Partenkirchen, Dumont d'Urville). The median difference of the CCI-GOMOS (Level 3) extinction and ground-based lidar profiles is between ~15% and ~45% in the 16–21km altitude range, depending on the considered site and aerosol type.The CCI-GOMOS dataset was subsequently used, together with a MIPAS SO2 time series, to update a volcanic eruption inventory published previously, thus providing a more comprehensive list of eruptions for the ENVISAT period (2002–2012). The number of quantified eruptions increases from 102 to 230 in the updated inventory. This new inventory was used to simulate the evolution of the global radiative forcing by application of the EMAC chemistry-climate model. Results of this simulation improve the agreement between modelled global radiative forcing of stratospheric aerosols at about 100hPa compared to values estimated from observations. Medium eruptions like the ones of Soufriere Hills/Rabaul (2006), Sarychev (2009) and Nabro (2011) cause a forcing change from about −0.1W/m2 to −0.2W/m2.

Calibration of a large-scale hydrological model using satellite-based soil moisture and evapotranspiration products

Abstract. A considerable number of river basins around the world lack sufficient ground observations of hydro-meteorological data for effective water resources assessment and management. Several approaches can be developed to increase the quality and availability of data in these poorly gauged or ungauged river basins; among them, the use of Earth observations products has recently become promising. Earth observations of various environmental variables can be used potentially to increase knowledge about the hydrological processes in the basin and to improve streamflow model estimates, via assimilation or calibration. The present study aims to calibrate the large-scale hydrological model PCRaster GLOBal Water Balance (PCR-GLOBWB) using satellite-based products of evapotranspiration and soil moisture for the Moroccan Oum er Rbia River basin. Daily simulations at a spatial resolution of 5 × 5 arcmin are performed with varying parameters values for the 32-year period 1979–2010. Five different calibration scenarios are inter-compared: (i) reference scenario using the hydrological model with the standard parameterization, (ii) calibration using in situ-observed discharge time series, (iii) calibration using the Global Land Evaporation Amsterdam Model (GLEAM) actual evapotranspiration time series, (iv) calibration using ESA Climate Change Initiative (CCI) surface soil moisture time series and (v) step-wise calibration using GLEAM actual evapotranspiration and ESA CCI surface soil moisture time series. The impact on discharge estimates of precipitation in comparison with model parameters calibration is investigated using three global precipitation products, including ERA-Interim (EI), WATCH Forcing methodology applied to ERA-Interim reanalysis data (WFDEI) and Multi-Source Weighted-Ensemble Precipitation data by merging gauge, satellite and reanalysis data (MSWEP). Results show that GLEAM evapotranspiration and ESA CCI soil moisture may be used for model calibration resulting in reasonable discharge estimates (NSE values from 0.5 to 0.75), although better model performance is achieved when the model is calibrated with in situ streamflow observations. Independent calibration based on only evapotranspiration or soil moisture observations improves model predictions to a lesser extent. Precipitation input affects discharge estimates more than calibrating model parameters. The use of WFDEI precipitation leads to the lowest model performances. Apart from the in situ discharge calibration scenario, the highest discharge improvement is obtained when EI and MSWEP precipitation products are used in combination with a step-wise calibration approach based on evapotranspiration and soil moisture observations. This study opens up the possibility of using globally available Earth observations and reanalysis products of precipitation, evapotranspiration and soil moisture in large-scale hydrological models to estimate discharge at a river basin scale.

Compilation and Validation of SAR and Optical Data Products for a Complete and Global Map of Inland/Ocean Water Tailored to the Climate Modeling Community

Accurate maps of surface water extent are of paramount importance for water management, satellite data processing and climate modeling. Several maps of water bodies based on remote sensing data have been released during the last decade. Nonetheless, none has a truly (90 ∘ N/90 ∘ S) global coverage while being thoroughly validated. This paper describes a global, spatially-complete (void-free) and accurate mask of inland/ocean water for the 2000–2012 period, built in the framework of the European Space Agency (ESA) Climate Change Initiative (CCI). This map results from the synergistic combination of multiple individual SAR and optical water body and auxiliary datasets. A key aspect of this work is the original and rigorous stratified random sampling designed for the quality assessment of binary classifications where one class is marginally distributed. Input and consolidated products were assessed qualitatively and quantitatively against a reference validation database of 2110 samples spread throughout the globe. Using all samples, overall accuracy was always very high among all products, between 98 % and 100 % . The CCI global map of open water bodies provided the best water class representation (F-score of 89 % ) compared to its constitutive inputs. When focusing on the challenging areas for water bodies’ mapping, such as shorelines, lakes and river banks, all products yielded substantially lower accuracy figures with overall accuracies ranging between 74 % and 89 % . The inland water area of the CCI global map of open water bodies was estimated to be 3.17 million km 2 ± 0.24 million km 2 . The dataset is freely available through the ESA CCI Land Cover viewer.

Testing the Quality of Sea-Level Data Using the GECCO Adjoint Assimilation Approach

Besides providing an estimate of the changing ocean state, an important result of the dynamically consistent estimating the circulation and climate of the ocean (ECCO) state estimate approach is the provision of a posterior model–data residuals which contain important information about elements in the assimilated observations that are inconsistent with the model dynamics or with the information present in other ocean data sets that are being used as constraints in the assimilation procedure. Based on decreased GECCO2 model–data residuals, upon using the altimeter data through the ESA climate change initiative (cci) sea-level (SL) project, we show here that the recently reprocessed ESA SL_cci altimeter data set (SL1) has been improved relative to the earlier AVISO altimetry data set and is now more consistent with the GECCO2 estimate and with the information about the changing ocean state embedded in other ocean data sets. The improvement can be shown to exist separately for both TOPEX/POSEIDON and ERS data sets. The study reveals that especially in regions characterized by small sea surface height (SSH) variability and small signal-to-noise ratio in the SSH data, improvements can be on the order of 30% of previously existing model–data residuals. However, in some regions we can find degradations, particulary in those where GECCO2 has little skill in representing the altimeter data and where evaluation of the products with GECCO2 is thus not advisable. Upon the assimilation of the new SL1 data set, the GECCO2 synthesis was further improved. However, adding the sea surface temperature (SST) from the SST_cci project as additional constrain, no further impact can be identified.

Combining satellite observations to develop a global soil moisture product for near-real-time applications

Abstract. The soil moisture dataset that is generated via the Climate Change Initiative (CCI) of the European Space Agency (ESA) (ESA CCI SM) is a popular research product. It is composed of observations from 10 different satellites and aims to exploit the individual strengths of active (radar) and passive (radiometer) sensors, thereby providing surface soil moisture estimates at a spatial resolution of 0.25°. However, the annual updating cycle limits the use of the ESA CCI SM dataset for operational applications. Therefore, this study proposes an adaptation of the ESA CCI product for daily global updates via satellite-derived near-real-time (NRT) soil moisture observations. In order to extend the ESA CCI SM dataset from 1978 to present we use NRT observations from the Advanced Scatterometer on-board the two MetOp satellites and the Advanced Microwave Scanning Radiometer 2 on-board GCOM-W. Since these NRT observations do not incorporate the latest algorithmic updates, parameter databases and intercalibration efforts, by nature they offer a lower quality than reprocessed offline datasets. In addition to adaptations of the ESA CCI SM processing chain for NRT datasets, the quality of the NRT datasets is a main source of uncertainty. Our findings indicate that, despite issues in arid regions, the new CCI NRT dataset shows a good correlation with ESA CCI SM. The average global correlation coefficient between CCI NRT and ESA CCI SM (Pearson's R) is 0.80. An initial validation with 40 in situ observations in France, Spain, Senegal and Kenya yields an average R of 0.58 and 0.49 for ESA CCI SM and CCI NRT, respectively. In summary, the CCI NRT product is nearly as accurate as the existing ESA CCI SM product and, therefore, of significant value for operational applications such as drought and flood forecasting, agricultural index insurance or weather forecasting.

Causes of the Regional Variability in Observed Sea Level, Sea Surface Temperature and Ocean Colour Over the Period 1993–2011

We analyse the regional variability in observed sea surface height (SSH), sea surface temperature (SST) and ocean colour (OC) from the ESA Climate Change Initiative datasets over the period 1993–2011. The analysis focuses on the signature of the ocean large-scale climate fluctuations driven by the atmospheric forcing and do not address the mesoscale variability. We use the ECCO version 4 ocean reanalysis to unravel the role of ocean transport and surface buoyancy fluxes in the observed SSH, SST and OC variability. We show that the SSH regional variability is dominated by the steric effect (except at high latitude) and is mainly shaped by ocean heat transport divergences with some contributions from the surface heat fluxes forcing that can be significant regionally (confirming earlier results). This is in contrast with the SST regional variability, which is the result of the compensation of surface heat fluxes by ocean heat transport in the mixed layer and arises from small departures around this background balance. Bringing together the results of SSH and SST analyses, we show that SSH and SST bear some common variability. This is because both SSH and SST variability show significant contributions from the surface heat fluxes forcing. It is evidenced by the high correlation between SST and buoyancy-forced SSH almost everywhere in the ocean except at high latitude. OC, which is determined by phytoplankton biomass, is governed by the availability of light and nutrients that essentially depend on climate fluctuations. For this reason, OC shows significant correlation with SST and SSH. We show that the correlation with SST displays the same pattern as the correlation with SSH with a negative correlation in the tropics and subtropics and a positive correlation at high latitude. We discuss the reasons for this pattern.

Error decomposition of nine passive and active microwave satellite soil moisture data sets over Australia

Abstract Soil moisture is one of the essential climate variables for the Global Climate Observing System (GCOS) that has been prioritized by the ESA's Climate Change Initiative to construct its homogeneous long-term climate record. This requires a consistent characterization of the error structures in the individual data sets, which vary due to changes in instrument configuration and calibration, and retrieval algorithm design. In this paper, the random error and systematic differences in nine passive and active microwave satellite soil moisture products over Australia (time coverage: 1978–present) are estimated in a same manner for SM components at subseasonal and seasonal-to-interannual timescales separately. The multi-scale error structures are found to be non-trivial and vary between the products, giving cause for conducting multi-scale merging with awareness of these differences. Noticeable similarities between the error structures of the satellite products derived from same retrieval algorithm and same measuring frequency however suggest transferability of error parameters between them. Using partial rank correlation analysis, the error maps are linked to statistics on vegetation index, digital elevation, soil moisture and soil temperature, and land cover fractions and mixing in order to explain the observed variability and the similarities between the products.

The Sodankylä in situ soil moisture observation network: an example application of ESA CCI soil moisture product evaluation

Abstract. During the last decade there has been considerable development in remote sensing techniques relating to soil moisture retrievals over large areas. Within the framework of the European Space Agency's (ESA) Climate Change Initiative (CCI) a new soil moisture product has been generated, merging different satellite-based surface soil moisture based products. Such remotely sensed data need to be validated by means of in situ observations in different climatic regions. In that context, a comprehensive, distributed network of in situ measurement stations gathering information on soil moisture, as well as soil temperature, has been set up in recent years at the Finnish Meteorological Institute's (FMI) Sodankylä Arctic research station. The network forms a calibration and validation (CAL–VAL) reference site and is used as a tool to evaluate the validity of satellite retrievals of soil properties. In this paper we present the Sodankylä CAL–VAL reference site soil moisture observation network, its instrumentation as well as its areal representativeness over the study area and the region in general as a whole. As an example of data utilization, comparisons of spatially weighted average top-layer soil moisture observations between the years 2012 and 2014 against ESA CCI soil moisture data product estimates are presented and discussed. The comparisons were made against a single ESA CCI data product pixel encapsulating most of the Sodankylä CAL–VAL network sites. Comparisons are made with daily averaged and running weekly averaged soil moisture data as well as through application of an exponential soil moisture filter. The overall achieved correlation between the ESA CCI data product and in situ observations varies considerably (from 0.479 to 0.637) depending on the applied comparison perspective. Similarly, depending on the comparison perspective used, inter-annual correlation comparison results exhibit even more pronounced variation, ranging from 0.166 to 0.840.

Variations of Annual Minimum Snow and Ice Extent over Canada and Neighboring Landmass Derived from MODIS 250-m Imagery for 2000–2014

. Snow and ice are important hydrological resources. Their minimum spatial extent over land, here referred to as annual minimum snow/ice (MSI) cover, plays a very important role as an indicator of long-term changes and baseline capacity for surface water storage. Data from Moderate Resolution Imaging Spectroradiometer (MODIS) on Terra satellite for the period of 2000–2014 were utilized in this study. The level-2 MODIS swath imagery for bands B1 to B7 was employed and the 500-m bands B3–B7 were spatially downscaled to a 250-m swath grid. The imagery is available daily with multiple overpasses. This allows for more accurate identification of annual minimum in comparison to high-resolution imagery (e.g., Landsat, ASTER, etc.) available at much coarser temporal rates. Atmospherically corrected 10-day clear-sky composites converted into normalized surface reflectance over the warm season (April 1 to September 20) were employed to identify persistent snow and ice presence. Results were compared with our previous results derived from the MODIS Circumpolar Arctic clear-sky composites, generated for the end of melting season, and showed smaller MSI extent by 24%, on average. Produced MSI distributions were also compared with the permanent snow and ice maps available from 6 global land cover datasets: (i) Global Land Cover GLC-2000, (ii & iii) European Space Agency's (ESA) Globcover circa 2005 and 2009, (iv–vi) land cover maps derived under the ESA Climate Change Initiative (CCI) for 2000, 2005, and 2010. Significant biases were discovered between various land cover datasets and our results. For example, GLC-2000 overestimated snow/ice extent by 194% (325,400 km2) for the Canadian Arctic. The biases over the entire landmass (excluding Greenland) are 135% (3.7 × 105 km2), 113% (3.0 × 105 km2), 89% (2.2 × 105 km2), and 28% (0.8 × 105 km2) between our results and GLC-2000, ESA Globcover 2005, ESA Globcover 2009, and ESA CCI datasets, correspondingly. The derived MSI extent was compared with Randolph Glacier Inventory (RGI) 4.0 and showed much better consistency (ranging from 1% to 15%).

Evaluating ESA CCI soil moisture in East Africa

To assess growing season conditions where ground based observations are limited or unavailable, food security and agricultural drought monitoring analysts rely on publicly available remotely sensed rainfall and vegetation greenness. There are also remotely sensed soil moisture observations from missions like the European Space Agency (ESA), Soil Moisture and Ocean Salinity (SMOS) and NASA’s Soil Moisture Active Passive (SMAP); however, these time series are still too short to conduct studies that demonstrate the utility of these data for operational applications, or to provide historical context for extreme wet or dry events.To promote the use of remotely sensed soil moisture in agricultural drought and food security monitoring, we evaluate the quality of a 30+ year time series of merged active–passive microwave soil moisture from the ESA Climate Change Initiative (CCI-SM) over East Africa. Compared to the Normalized Difference Vegetation index (NDVI) and modeled soil moisture products, we find substantial spatial and temporal gaps in the early part of the CCI-SM record, with adequate data coverage beginning in 1992. From this point forward, growing season CCI-SM anomalies are well correlated (R>0.5) with modeled soil moisture, and in some regions, NDVI. We use pixel-wise correlation analysis and qualitative comparisons of seasonal maps and time series to show that remotely sensed soil moisture can inform remote drought monitoring that has traditionally relied on rainfall and NDVI in moderately vegetated regions.

An inter-comparison of soil moisture data products from satellite remote sensing and a land surface model

Significant advances have been achieved in generating soil moisture (SM) products from satellite remote sensing and/or land surface modeling with reasonably good accuracy in recent years. However, the discrepancies among the different SM data products can be considerably large, which hampers their usage in various applications. The bias of one SM product from another is well recognized in the literature. Bias estimation and spatial correction methods have been documented for assimilating satellite SM product into land surface and hydrologic models. Nevertheless, understanding the characteristics of each of these SM data products is required for many applications where the most accurate data products are desirable. This study inter-compares five SM data products from three different sources with each other, and evaluates them against in situ SM measurements over 14-year period from 2000 to 2013. Specifically, three microwave (MW) satellite based data sets provided by ESA's Climate Change Initiative (CCI) (CCI-merged, -active and -passive products), one thermal infrared (TIR) satellite based product (ALEXI), and the Noah land surface model (LSM) simulations. The in-situ SM measurements are collected from the North American Soil Moisture Database (NASMD), which involves more than 600 ground sites from a variety of networks. They are used to evaluate the accuracies of these five SM data products. In general, each of the five SM products is capable of capturing the dry/wet patterns over the study period. However, the absolute SM values among the five products vary significantly. SM simulations from Noah LSM are more stable relative to the satellite-based products. All TIR and MW satellite based products are relatively noisier than the Noah LSM simulations. Even though MW satellite based SM retrievals have been predominantly used in the past years, SM retrievals of the ALEXI model based on TIR satellite observations demonstrate skills equivalent to all the MW satellite retrievals and even slightly better over certain regions. Compared to the individual active and passive MW products, the merged CCI product exhibits higher anomaly correlation with both Noah LSM simulations and in-situ SM measurements.

Future measurements for climate monitoring

Future measurements for climate monitoring

The GOME-type Total Ozone Essential Climate Variable (GTO-ECV) data record from the ESA Climate Change Initiative

Abstract. We present the new GOME-type Total Ozone Essential Climate Variable (GTO-ECV) data record which has been created within the framework of the European Space Agency's Climate Change Initiative (ESA-CCI). Total ozone column observations – based on the GOME-type Direct Fitting version 3 algorithm – from GOME (Global Ozone Monitoring Experiment), SCIAMACHY (SCanning Imaging Absorption SpectroMeter for Atmospheric CHartographY), and GOME-2 have been combined into one homogeneous time series, thereby taking advantage of the high inter-sensor consistency. The data record spans the 15-year period from March 1996 to June 2011 and it contains global monthly mean total ozone columns on a 1°× 1° grid. Geophysical ground-based validation using Brewer, Dobson, and UV–visible instruments has shown that the GTO-ECV level 3 data record is of the same high quality as the equivalent individual level 2 data products that constitute it. Both absolute agreement and long-term stability are excellent with respect to the ground-based data, for almost all latitudes apart from a few outliers which are mostly due to sampling differences between the level 2 and level 3 data. We conclude that the GTO-ECV data record is valuable for a variety of climate applications such as the long-term monitoring of the past evolution of the ozone layer, trend analysis and the evaluation of chemistry–climate model simulations.

Multi-year global land cover mapping at 300 m and characterization for climate modelling: achievements of the Land Cover component of the ESA Climate Change Initiative

Abstract. Essential Climate Variables were listed by the Global Climate Observing System as critical information to further understand the climate system and support climate modelling. The European Space Agency launched its Climate Change Initiative in order to provide an adequate response to the set of requirements for long-term satellite-based products for climate. Within this program, the CCI Land Cover project aims at revisiting all algorithms required for the generation of global land cover products that are stable and consistent over time, while also reflecting the land surface seasonality. To this end, the land cover concept is revisited to deliver a set of three consistent global land cover products corresponding to the 1998-2002, 2003-2007 and 2008-2012 periods, along with climatological 7-day time series representing the average seasonal dynamics of the land surface over the 1998-2012 period. The full Envisat MERIS archive (2003-2012) is used as main Earth Observation dataset to derive the 300-m global land cover maps, complemented with SPOT-Vegetation time series between 1998 and 2012. Finally, a 300-m global map of open permanent water bodies is derived from the 2005-2010 archive of the Envisat Advanced SAR imagery mainly acquired in the 150m Wide Swath Mode.

Satellite-based climate information within the WMO RA VI Regional Climate Centre on Climate Monitoring

Abstract. The World Meteorological Organization (WMO) established Regional Climate Centres (RCCs) around the world to create science-based climate information on a regional scale within the Global Framework for Climate Services (GFCS). The paper introduces the satellite component of the WMO Regional Climate Centre on Climate Monitoring (RCC-CM) for Europe and the Middle East. The RCC-CM product portfolio is based on essential climate variables (ECVs) as defined by the Global Climate Observing System (GCOS), spanning the atmospheric (radiation, clouds, water vapour) and terrestrial domains (snow cover, soil moisture). In the first part, the input data sets are briefly described, which are provided by the EUMETSAT (European Organisation for the Exploitation of Meteorological Satellites) Satellite Application Facilities (SAF), in particular CM SAF, and by the ESA (European Space Agency) Climate Change Initiative (CCI). In the second part, the derived RCC-CM products are presented, which are divided into two groups: (i) operational monitoring products (e.g. monthly means and anomalies) based on near-real-time environmental data records (EDRs) and (ii) climate information records (e.g. climatologies, time series, trend maps) based on long-term thematic climate data records (TCDRs) with adequate stability, accuracy and homogeneity. The products are provided as maps, statistical plots and gridded data, which are made available through the RCC-CM website (www.dwd.de/rcc-cm).