Equimolar Mixture Research Articles

Spontaneous formation of Au-Co interface via a Low-Temperature reduction process

Eutectic alloys manufactured by metallurgical methods are widely used in many industrial applications due to their special properties provided by the multi-phase eutectic microstructure. Previous studies introduced the preparation of metals and alloys through the chemical reduction of metal complex salts. We employed this technique to prepare the equiatomic composition in the binary eutectic system Au-Co through a low-temperature solid-gas phase reduction of two precursors: the bi-metallic complex salt [Co(NH3)6][AuCl4]Cl2, and an equimolar mixture of H[AuCl4] and pre-reduced cobalt. Complete reduction at 350 °C resulted in the formation of a close-to-equilibrium two-phase composition of fcc gold and hcp cobalt. The structure of the fully reduced metallic materials was composed of interconnected cobalt ligaments and bi-metallic Au-Co (gold-cobalt) particles. Specifically, these spontaneously formed particles featured fcc cobalt islands interfacing with fcc gold at a specific orientation relationship. Under heating, the fully reduced Au-Co products underwent melting that corresponds to the equilibrium eutectic melting point at 996.5 °C. These results imply that spontaneous lattice self-adjustment can occur in multi-component eutectic-type systems at low temperatures directly in the solid state. This may ease the technologies of joining such as epitaxial growth, additive manufacturing, and powder metallurgy.

Reduced Growth in Eustoma under High Nutrient and Phytotoxic Organic Acid Concentrations and Recovery through Hot Water Conditioning of Continuously Cropped Soil

Stunted vegetative growth and delayed or absent flowering are commonly observed in eustoma (Eustoma grandiflorum) when cultivated continuously in the same greenhouse soil. These effects are likely caused by the excessive accumulation of soluble salts and/or phytotoxic organic acids in the soil. This study aimed to clarify the mechanism of continuous cropping obstacles and formulate prevention measures of eustoma. Seedlings of eustoma ‘Croma III White’ were grown hydroponically with 0%, 25%, 50%, 75%, 100% (full), 125%, 150%, 175%, or 200% strength of Johnson’s solution. Plant height, leaf area, and shoot dry weight increased steadily as solution strength increased from 25% to 125% [solution electrical conductivity (EC) of 2.4 dS⋅m−1] and then gradually decreased as solution strength further increased from 125% to 200% (solution EC of 3.8 dS⋅m−1). When grown hydroponically in 200% strength Johnson’s solution, plant height, leaf area, and root length increased with increasing equimolar mixtures of organic acids, including maleic acid, benzoic acid, malic acid, and hydroxybenzoic acid, up to 1.2 to 1.6 mM and decreased thereafter. Node number and the percentage of flower bud visibility declined beyond 1.6 mM organic acid mixtures. Plants with 2.0 and 2.4 mM organic acid mixtures had the lowest net photosynthetic rate, stomatal conductance, transpiration, and intercellular carbon dioxide concentration. Plants had normal growth and produced flower buds when the continuously cropped soil was preconditioned with 100 °C reverse-osmosis water before planting.

Green chemistry route to chitosan hydrogels and investigation of the materials as efficient dye adsorbents

Abstract Biopolymer-based materials for the adsorption of toxic dyes represent an interesting class of materials for environmental applications. Here we report on chitosan as the starting material for synthesizing dye adsorbents. In particular, the synthesis, characterization, and cationic dye adsorption properties of chitosan hydrogel adsorbents are reported. Polyanionic itaconated chitosan derivatives were synthesized in solvent-less conditions for the first time. Itaconated chitosan was cross-linked using thiol-ene chemistry to obtain hydrogels. The influence of the incorporated carboxylate groups and the cross-linker fraction on the adsorption of Methylene Blue (MB) was investigated. In addition, the impact of pH, adsorbent dose, initial concentration, and ionic strength were investigated to determine the optimum conditions for MB uptake, and the dye uptake kinetics, adsorption isotherms, selectivity, and reusability of the adsorbents were unveiled. A maximum adsorption capacity of 556 mg/g could be achieved, outperforming commercial activated charcoal and ion exchange resins. Furthermore the chitosan hydrogel adsorbents were shown to capture >90 % of cationic MB from a binary equimolar mixture with the anionic dye Methyl Orange. Since the adsorbents can be regenerated and re-used afterwards at least 20 times, retaining a high dye adsorption fraction of >95 %, these materials are promising candidates for environmental applications.

Luminescent Porous Organic Crystals for Adsorptive Separation of Toluene and Methylcyclohexane.

A butterfly-shaped phenothiazine derivative, PTTCN, was synthesized to obtain pure organic porous crystals for the highly efficient absorptive separation of toluene (Tol) and methylcyclohexane (Mcy). Due to the presence of three polar cyano groups and nonplanar conformation, these molecules self-assembled into a hydrogen-bonded organic framework (X-HOF-5) with distinct cavities capable of accommodating Tol molecules through multiple hydrogen-bonding interactions. Upon solvent removal via heating, the activated X-HOF-5 retained its cavity structure albeit with altered stacking arrangements, accompanied by a remarkable fluorescent color change from cyan to green. X-HOF-5a can undergo a phase transformation into X-HOF-5 upon reabsorption of Tol, while exhibiting no accommodation of Mcy due to the weak intermolecular interaction between PTTCN and Mcy. This suggests that the activated HOF material prefers Tol over Mcy. Moreover, X-HOF-5a may selectively accommodate Tol in a Tol/Mcy equimolar mixture, and the purity of Tol can reach 97% after release from the framework. Additionally, it is noteworthy that the HOF material exhibits recyclability without any discernible loss in performance.

Five New Analogs of Streptogramin Antibiotic Viridogrisein Isolated from Streptomyces niveoruber.

Five new viridogriseins B-F were isolated from Streptomyces niveoruber, along with viridogrisein and griseoviridin which belong to streptogramin family antibiotics. A combination of liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis and the advanced Marfey's method elucidated the structures of viridogriseins B-F, each featuring distinct constituent amino acids. Consistent with other streptogramin family antibiotics, these viridogrisein analogs exhibited potent antibacterial activity against Staphylococcus aureus. Furthermore, equimolar mixtures of each viridogrisein analog and griseoviridin inhibited the growth of S. aureus more potently than each analog treatment alone. Finally, an in vitro functional analysis of SgvY, encoded in the viridogrisein biosynthetic gene cluster, revealed that SgvY detoxifies viridogrisein against S. aureus by linearization. Considering that viridogrisein is not autotoxic to S. niveoruber, SgvY likely contributes to the self-resistance system against viridogrisein in S. niveoruber.

Thioarylation of 6-Amino-2,3,6-trideoxy-d-manno-oct-2-ulosonic Acid (IminoKdo): Access to 3,6-Disubstituted Picolinates and Mechanistic Insights.

In this work, we present a metal-free coupling protocol for the regio- and stereoselective C3-thioarylation of 6-amino-2,3,6-trideoxy-d-manno-oct-2-ulosonic acid (iminoKdo). The developed procedure enables the coupling of electron-rich, electron-deficient, and hindered arylthiols, providing a series of C3-modified iminoKdo derivatives in moderate to good yields. Elucidation of active species through controlled experimental studies and time-lapse 31 P NMR analysis provides insights into the reaction mechanism. We demonstrate that, following a tandem Staudinger/aza-Wittig reaction of an azido-containing keto ester, an inseparable equimolar mixture of imine/enamine is formed. The enamine then undergoes a Stork-like nucleophilic attack with the in situ-formed disulfide reagent, resulting in the formation of the coupling products. Additionally, we describe a rarely reported acid-promoted aromatization of the C3-thioarylated iminoKdo skeleton into 3,6-disubstituted picolinates, which are reminiscent of dichotomines.

Mechanochemical ignition of self-propagating reactions in equimolar Al-Ni powder mixtures and multilayers.

This work addresses a long standing question in the field of mechanochemistry, namely the role of mesostructure in the initiation of self-propagating high-temperature reactions in exothermic chemical systems, commonly referred to as ignition. In an attempt to find robust evidence in this regard, we compare the ignition behaviour of equimolar Al-Ni powder mixtures and equimolar Al-Ni multilayers. To achieve the best possible control of experimental conditions and allowing high reproducibility, we used elemental powders sieved in the range between 20 μm and 44 μm, and multilayers with bi-layer thickness between 10 nm and 800 nm. We carried out systematic ball milling experiments involving pristine powder mixtures and multilayers as well as a mix of pristine material and material prone to ignition suitably prepared. Experimental findings suggest that pristine powder mixtures and multilayers with bi-layer thickness of 240 nm have analogous ignition behaviour. Along the same lines, data suggest that pristine powder mixtures undergo ignition when they attain a mesostructure similar to that of multilayers with bi-layer thickness of 10 nm.

Thickness determination of hydroperoxidized lipid bilayers from medium-resolution cryo-TEM images.

As the primary products of lipid oxidation, lipid hydroperoxides constitute an important class of lipids generated by aerobic metabolism. However, despite several years of effort, the structure of the hydroperoxidized bilayer has not yet been observed under electron microscopy. Here we use a 200kV Cryo-TEM to image small unilamellar vesicles (SUVs) made (i) of pure POPC or SOPC, (ii) of their pure hydroperoxidized form, and(iii) of their equimolar mixtures. We show that the challenges posed by the determination of the thickness of the hydroperoxidized bilayers under these observation conditions can be addressed by an image analysis method that we developed and describe here.

Vapochromic separation of toluene and pyridine azeotropes using adaptive macrocycle co-crystals.

The separation of toluene (Tol) and pyridine (Py) azeotropes is significant in the chemical industry. Herein, we present a new method for the energy-efficient separation of Tol and Py using pillar[5]arene-based adaptive macrocycle co-crystals (MCCs) that can selectively separate Py from a Py/Tol equimolar mixture with 99.2% purity, accompanied by vapochromic behavior from white to yellow.

Resolving a structural issue in cerium-nickel-based oxide: a single compound or a two-phase system?

CeNiO3 has been reported in the literature in the last few years as a novel LnNiO3 compound with promising applications in different catalytic fields, but its structure has not been correctly reported so far. In this research, CeNiO3 (RB1), CeO2 and NiO have been synthesized in a nanocrystalline form using a modified citrate aqueous sol-gel route. A direct comparison between the equimolar physical mixture (n(CeO2) : n(NiO) = 1 : 1) and compound RB1 was made. Their structural differences were investigated by laboratory powder X-ray diffraction (PXRD), selected area electron diffraction (SAED), transmission electron microscopy (TEM) with an energy-dispersive X-ray spectroscopy (EDS) detector, and Raman spectroscopy. The surface of the compounds was analyzed by X-ray photoelectron spectroscopy (XPS), while the thermal behaviour was explored by thermogravimetric analysis (TGA). Their magnetic properties were also investigated with the aim of exploring the differences between these two compounds. There were clear differences between the physical mixture of CeO2 + NiO and RB1 presented by all of these employed methods. Synchrotron methods, such as atomic pair distribution function analysis (PDF), X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS), were used to explore the structure of RB1 in more detail. Three different models for the structural solution of RB1 were proposed. One structural solution proposes that RB1 is a single-phase pyrochlore compound (Ce2Ni2O7) while the other two solutions suggest that RB1 is a two-phase system of either CeO2 + NiO or Ce1-xNixO2 and NiO.

Formation of a low-symmetry Pd8 molecular barrel employing a hetero donor tetradentate ligand, and its use in the binding and extraction of C70.

The majority of reported metallo-supramolecules are highly symmetric homoleptic assemblies of M x L y type, with a few reports on assemblies that are obtained using multicomponent self-assembly or using ambidentate ligands. Herein, we report the use of an unsymmetrical tetratopic ligand (Lun) containing pyridyl and imidazole donor sites in combination with a cis-protected Pd(ii) acceptor for the formation of a low-symmetry M8Lun 4 molecular barrel (UNMB). Four potential orientational isomeric (HHHH, HHHT, HHTT, and HTHT) molecular barrels can be anticipated for the M8Lun 4 type metallo-assemblies. However, the formation of an orientational isomer (HHTT) of the barrel was suggested from single-crystal X-ray diffraction and 1H NMR analysis of UNMB. Two large open apertures at terminals and the hydrophobic confined space surrounded by four aromatic panels of Lun make UNMB a potential host for bigger guests. UNMB encapsulates fullerenes C70 and C60 favoured by non-covalent interactions between the fullerenes and aromatic panels of the ligand molecules. Experimental and theoretical studies revealed that UNMB has the ability to bind C70 more strongly than its lower analogue C60. The stronger affinity of UNMB towards C70 was exploited to separate C70 from an equimolar mixture of C70 and C60. Moreover, C70 can be extracted from the C70⊂UNMB complex by toluene, and therefore, UNMB can be reused as a recyclable separating agent for C70 extraction.

Disruptive effects of plasticizers bisphenol A, F, and S on steroidogenesis of adrenocortical cells.

Endocrine disrupting chemicals (EDCs) are known to interfere with endocrine homeostasis. Their impact on the adrenal cortex and steroidogenesis has not yet been sufficiently elucidated. This applies in particular to the ubiquitously available bisphenols A (BPA), F (BPF), and S (BPS). NCI-H295R adrenocortical cells were exposed to different concentrations (1nM-1mM) of BPA, BPF, BPS, and an equimolar mixture of them (BPmix). After 72 hours, 15 endogenous steroids were measured using LC-MS/MS. Ratios of substrate and product of CYP-regulated steps were calculated to identify most influenced steps of steroidogenesis. mRNA expression of steroidogenic enzymes was determined by real-time PCR. Cell viability remained unaffected at bisphenol concentrations lower than 250 µM. All tested bisphenols and their combination led to extensive alterations in the quantified steroid levels. The most profound fold changes (FC) in steroid concentrations after exposure to BPA (>10µM) were seen for androstenedione, e.g. a 0.37±0.11-fold decrease at 25µM (p≤0.0001) compared to vehicle-treated controls. For BPF, levels of 17-hydroxyprogesterone were significantly increased by 25µM (FC 2.57±0.49, p≤0.001) and 50µM (FC 2.65±0.61, p≤0.0001). BPS treatment led to a dose-dependent decrease of 11-deoxycorticosterone at >1µM (e.g. FC 0.24±0.14, p≤0.0001 at 10µM). However, when combining all three bisphenols, additive effects were detected: e.g. 11-deoxycortisosterone was decreased at doses >10µM (FC 0.27±0.04, p≤0.0001, at 25µM), whereas 21-deoxycortisol was increased by 2.92±0.20 (p≤0.01) at 10µM, and by 3.21±0.45 (p≤0.001) at 50µM. While every measured androgen (DHEA, DHEAS, androstenedione, testosterone, DHT) was lowered in all experiments, estradiol levels were significantly increased by BPA, BPF, BPS, and BPmix (e.g. FC 3.60±0.54, p≤0.0001 at 100µM BPF). Calculated substrate-product ratios indicated an inhibition of CYP17A1-, and CYP21A2 mediated conversions, whereas CYP11B1 and CYP19A1 showed higher activity in the presence of bisphenols. Based on these findings, most relevant mRNA expression of CYP genes were analysed. mRNA levels of StAR, CYP11B1, and CYP17A1 were significantly increased by BPF, BPS, and BPmix. In cell culture, bisphenols interfere with steroidogenesis at non-cytotoxic levels, leading to compound-specific patterns of significantly altered hormone levels. These results justify and call for additional in-vivo studies to evaluate effects of EDCs on adrenal gland functionality.

Ring-opening (co)polymerization of chiral seven-membered lactones mediated by achiral yttrium catalysts: insights into the catalyst stereocontrol by mass spectrometry

The ROCOP of equimolar mixtures of (R)-CLnBu/(S)-CLMe enabled the assessment of the ROP stereocontrol ability of yttrium catalysts through the degree of alternation via detailed mass spectrometric analyses.

Cytidine does not affect acute toxicity of intravenously administered choline.

Cytidine-5'-diphosphocholine (CDP-choline) is a key precursor for the intracellular synthesis of phosphatidylcholine and other phospholipids. Following either intravenous or oral application citicoline (CDP-choline of exogenous origin) undergoes quick decomposition to cytidine and choline, and for this reason it is frequently considered a prodrug. However, upon acute intravenous application in mice citicoline is, on a molar basis, 20 times less toxic than choline. To find out whether cytidine may attenuate toxicity of choline, in the present experiments we compared maximum tolerated doses of single intravenous injections of choline and equimolar mixture of choline and cytidine. We assumed that, if after oral intake a substantial part of citicoline is catabolised already in the intestine and its catabolites enter blood separately, intravenously applied equimolar mixture of cytidine and choline will be markedly less toxic than an equivalent molar dose of choline. However, the maximum tolerated single doses determined in our experiment for choline and equimolar mixture of choline and cytidine were similar. These data suggest that citicoline taken orally is not significantly decomposed in the intestinal lumen, but absorbed to blood as the intact molecule.

Li-Ion Dynamics in Li2S:LiI Composites – on the Effect of Solid-Solution Formation on Overall Li+ Transport

The enormous interest in developing powerful all-solid-state Li-ion batteries led to a boost in electrolyte research. Some Li-ion conductors have Ag-bearing analogs; the fast Ag+ ion conductor, Ag3SI, could be one of such materials. So far, no clear evidence is available that the Li-counterpart, Li3SI, does exist. Here, we treated an equimolar mixture of Li2S and LiI in high-energy ball mills and followed structural changes via X-ray diffraction (XRD) and magic-angle spinning (MAS) 6,7Li nuclear magnetic resonance (NMR) measurements. Differences in local structures as sensed by MAS NMR will be discussed for annealed and non-annealed samples, that is, powder samples directly obtained after finishing the ball-milling procedure. For nanocrystalline, non-annealed Li2S:LiI, the MAS NMR response is characterized by a broad distribution of NMR lines showing chemical shifts between that of pure Li2S and LiI, hence pointing to the formation of solid-solution like regions.Ion dynamics on different length scales was probed with variable-temperature, potentiostatic conductivity spectroscopy as well as solid-state NMR spin-lattice relaxation (SLR) measurements. Defect-rich nanocrystalline Li2S:LiI has to be characterized by an overall conductivity that is 2 orders of magnitude higher as compared to that of the microcrystalline, annealed reference sample. SLR NMR experiments supports this result and reveal lower activation energies for both the fast local hopping ion dynamics and long-range ion diffusivity in the sample directly obtained after ball milling. Finally, mixing-time dependent 6Li 2D exchange NMR spectroscopy reveals even (very) slow Li+ exchange between the Li2S-rich and LiI-rich regions in the nanocrystalline sample. Off-diagonal intensities are especially seen for mixing times longer than 80 ms.

Effect of Ligand Aromaticity on Cyclohexane and Benzene Sorption in IRMOFs: A Computational Study.

A series of four isoreticular MOFs (IRMOF-1, -10, -14, and -16) were selected for a computational investigation of the effect of ligand aromaticity on the adsorption capacity of an aromatic VOC (benzene) compared to its nonaromatic analog (cyclohexane). The affinity of the adsorbates was evaluated by calculating Henry's constants and adsorption enthalpies. It has been evidenced that while KH values decrease with ligand elongation (IRMOF-10 and -16), inserting a pyrene core into the MOF structure (IRMOF-14) increases both the cyclohexane and benzene adsorption efficiency by ∼290 and 54%, respectively. To elucidate host-guest interactions, we sought to locate preferential adsorption sites in MOF structures for the two VOCs studied by using the GCMC method. It appears that benzene interacts with the metal center (Zn4O clusters) and most of the ligand while cyclohexane tends to localize preferentially only near the Zn4O clusters. Coadsorption isotherms (equimolar mixture of benzene and cyclohexane) demonstrated the preferential adsorption of cyclohexane due to the stronger affinity for the MOF structure. On the other hand, for other isoreticular structures, the ligand elongation leads to a shift of the adsorption curve of cyclohexane caused by pore size increase and therefore less interactions with the walls. This phenomenon is counterbalanced in the case of IRMOF-14 due to stronger interactions between the cyclohexane and pyrene groups. The present results thus open perspectives in the design of promising MOF candidates for high-performing separation and sorption/detection of hydrocarbon VOCs.

Hydrogen-bond network in an equimolar acetic acid–water mixture as studied by neutron scattering and density functional theory

The present study explores the hydrogen-bond network in an equimolar mixture of acetic acid and water (AA–W). The investigation was conducted using a combination of neutron scattering and Density Functional Theory (DFT). New neutron scattering data at large scattering wave vectors were analyzed to determine the total structure factor SM(q) and the molecular form factor F1(q) of the system. DFT calculations using the 6-311++G(d, p) basis set were performed to optimize the monomers and various AA–W H-bonded clusters, including one acetic acid (AA) molecule connected to one, two, and three water molecules. Consequently, three dimers, three trimers, and one tetramer have been considered in order to describe the local order in the mixture. In addition, this study focused on the H-bond interactions in the most probable clusters in the solution, using the natural bond orbital and the atoms in molecules analyses. Our analysis particularly shows that stronger H-bond interactions occur in the ring structures.

Physical Separation of Enantiomeric Products by Compartmentalized Parallel Kinetic Resolution.

Accessing each enantiomer of a chiral molecule starting from a racemic mixture remains a daunting challenge in chemistry. Indeed, until now, only a few solutions exist to separate enantiomers of an equimolar mixture of a chiral precursor. In this study, we establish a new strategy to prepare simultaneously and physically separate both enantioenriched enantiomers of a molecule starting from a racemic substrate. This process combines two enantiomeric catalytic systems, working in parallel, and separation by an achiral membrane with selective permeability. This unprecedented system was successfully applied to the simultaneous preparation of both enantiomers of chiral 1,2-diols starting from racemic epoxides using Jacobsen's hydrolytic kinetic resolution (HKR) in parallel.

Crystal structures of а series of 1-substituted imidazol-4,5-dicarboxylic acids

Abstract Crystal structure of a series of 1-alkylimidazole-4,5-dicarboxylic acids has been determined. It is shown that an increase in the length of the alkyl group leads to drastic changes in the crystal and molecular structures. 1-Methyl and 1-ethylimidazole-4,5-dicarboxylic acid crystallize in zwitterionic form, but 1-propyl- and 1-butylimidazole-4,5-dicarboxylic acid crystallize as rare equimolar mixture of neutral and zwitterionic tautomeric forms. The observed changes in the crystal and molecular structures are apparently associated with the steric factor, which determines both the packing method and the tautomeric composition of the unit cell.

Ethane-CO2 Mixture Adsorption in Silicalite: Influence of Tortuosity and Connectivity of Pores on Selectivity

Selective adsorption using nanoporous materials is an efficient strategy for separating gas mixtures. In a nanoporous material, pores can exist in different shapes and can have different degrees of inter-connectivity. In recent studies, both pore connectivity and tortuosity have been found to affect the adsorption and dynamical properties of ethane and CO2 in silicalite differently. Here, using Monte Carlo simulations, we investigate if these two attributes can affect the selective adsorption of one component from a mixture of ethane and CO2 in silicalite. For this, the adsorption of an equimolar mixture of ethane and CO2 is simulated in 12 models of silicalite—SnZm (n, m = 0, 1, 2, 3 or 4; with n and m denoting, respectively, the fraction (out of 4) of straight and zigzag channels of silicalite that are available for adsorption)—differing in degrees of pore connectivity and tortuosity. The adsorption selectivity in this system is found to exhibit a reversal with the adsorption dominated by ethane at low pressures (below ~1 atm) and by CO2 at higher pressures (above ~10 atm). Pore connectivity is found to suppress the selective adsorption of CO2 at higher pressures and also shifts the selectivity reversal to higher pressures. The selectivity reversal results from a competition between the polarizability-affected adsorption at lower pressures and efficient packing at higher pressures. The efficient packing of CO2 is a compounded effect resulting from the larger effective pore volume available for CO2 due to its stronger interaction with the pore surface and smaller molecular volume. CO2 molecules show a preference to adsorb in non-tortuous pores, and this preference is found to be stronger in the presence of ethane. The effects of pore connectivity and tortuosity elucidated here should be applicable to a wide range of natural and engineered nanoporous materials, and this knowledge could be used to identify materials with better capability for separating and storing CO2 based on their pore attributes.