Enhancement Of Density Research Articles

Optimization and mass transfer analysis under the ribs of multi-serpentine flow fields

This study aims to enhance the performance of Proton Exchange Membrane Fuel Cell (PEMFC) by optimizing the design of a three-channel serpentine flow field. The focus is on the introduction of sub-channels beneath the flow field ribs, utilizing the pressure differential between the main and sub-channels to strengthen lateral convection under the ribs, thus achieving uniform distribution of reaction gases. Using Computational Fluid Dynamics (CFD) methods, the performance of traditional and optimized flow fields were compared across various metrics. The results show that the introduction of sub-channels significantly improves gas mass transfer efficiency, enhances the uniformity of oxygen concentration and current density, and optimizes water content on the proton exchange membrane. At a voltage of 0.5 V, the Improved Serpentine Flow Field (ISCF) exhibits a notable enhancement in current density, increasing from 1.501 A/cm2 in the Traditional Serpentine Flow Field (TCSF) to 1.654 A/cm2 in the ISCF. This represents a significant 10 % increase in current density. Concurrently, the uniformity index climbs from 0.84 to 0.898, marking a 7 % improvement in uniformity. Furthermore, the ISCF design achieves a substantial reduction in pressure drop, decreasing from 1631 Pa to 1212 Pa, a reduction of 26 %. Additionally, the expansion of sub-channel width markedly boosts cell performance, whereas the Increase in sub-channel height reaches a saturation point beyond a certain threshold, indicating an optimal range for dimensional adjustments.

Enhancement of energy density for iron MOF-derived composite for aqueous supercapacitor by K3[Fe(CN)6] redox additive electrolyte

Redox additive added aqueous electrolyte attract extensive interest in supercapacitor application. Herein, the electrochemical of the synthesized Fe3O4/Si/GNP composite cathode electrode material was conducted in a two-electrode system via Swagelok cell assembly in the presence of with and without redox additive (0.2 M K3Fe(CN)6 in 1 M Li2SO4). The Fe3O4/Si/GNP composite was successfully synthesized by facile solvothermal method followed by calcination. The structural and morphology investigations of the Fe3O4/Si/GNP composite are conducted via XRD, FESEM, and BET analyses. The synergic effects between the composite material and redox-active ion (Fe2+/Fe3+) in the redox additive electrolyte enhance faradaic reactions, which are utilized to design a high-energy density supercapacitor. The Fe3O4/Si/GNP composite in redox additive electrolyte exhibits a 64.38 % increase in specific capacitance (319.45 F g−1 at 1 A g−1) and a 70.95 % increase in terms of energy density (35.56 Wh kg−1). Redox additive ions in the electrolyte enhance ionic conductivity and facilitate electron transfer across the porous structure of the Fe3O4/Si/GNP composite. The fast reversible kinetics of iron ions enable it to sustain decent cycle stability with a capacitance retention of 73.7 % after 1200 cycles.

High-temperature high-performance capacitive energy storage in polymer nanocomposites enabled by nanostructured MgO fillers

High-temperature high-performance polymer dielectric capacitors are essential for cutting-edge electronics and high-power systems operated in harsh environment conditions. Herein, dielectric composites comprising polyetherimide (PEI) polymers and easily prepared magnesium oxide (MgO) nanoparticles are fabricated by tape casting to promote capacitive performance at high temperatures. Benefiting from high-insulation behavior and wide bandgap of the MgO nanoparticles, the designed PEI nanocomposites deliver the significantly suppressed leakage current density and prominent enhancement of the breakdown strength, especially under high temperatures, the rationality of which is further revealed by finite element simulations on high-field distribution and electrical tree evolution. Accordingly, the nanocomposites containing ultra-low loading volume (0.5 vol%) MgO nanoparticles endow a large discharged energy density (~ 6.60 J cm−3) at 150 °C, which is ahead of most investigated 0–3 dielectric nanocomposites with inorganic fillers. Moreover, the excellent fatigue resistance at 150 °C is simultaneously achieved. This study demonstrates a practical route to develop scalable high-temperature polymer nanocomposite dielectrics blended with inorganic nanoparticles with superior capacitive performance, thus accelerating the development of dielectric polymer capacitors.

Symmetries and wave functions of photons confined in three-dimensional photonic band gap superlattices

We perform a computational study of confined photonic states that appear in a three-dimensional (3D) superlattice of coupled cavities, resulting from a superstructure of intentional defects. The states are isolated from the vacuum by a 3D photonic band gap, using a diamondlike inverse woodpile crystal structure, and they exhibit “Cartesian” hopping of photons in high-symmetry directions. We investigate the confinement dimensionality to verify which states are fully 3D-confined, using a recently developed scaling theory to analyze the influence of the structural parameters of the 3D crystal. We create confinement maps that trace the frequencies of 3D-confined bands for select combinations of key structural parameters, namely the pore radii of the underlying regular crystal and of the defect pores. We find that a certain minimum difference between the regular and defect pore radii is necessary for 3D-confined bands to appear, and that an increasing difference between the defect pore radii from the regular radii supports more 3D-confined bands. In our analysis, we find that their symmetries and spatial distributions are more varied than electronic orbitals known from solid-state physics. We surmise that this difference occurs since the confined photonic orbitals derive from global Bloch states governed by the underlying superlattice structure, whereas single-atom orbitals are localized. Based on this realization, we suggest that the extent symmetries of “photonic orbitals” could possibly translate to novel macroscopic behaviors of “photonic solid-state matter,” never before seen in the standard electronic solid-state systems. We also discover pairs of degenerate 3D-confined bands with p-like orbital shapes and mirror symmetries matching the symmetry of the superlattice. Finally, we investigate the enhancement of the local density of optical states for cavity quantum electrodynamics applications. We find that donorlike superlattices, i.e., where the defect pores are smaller than the regular pores, provide greater enhancement in the air region than acceptorlike structures with larger defect pores, and thus offer better prospects for doping with quantum dots and ultimately for 3D networks of single photons steered across strongly coupled cavities. Published by the American Physical Society 2024

Amorphous B coated Mg nanopowder induces low angle grain boundaries and enhances J c of MgB2 wire

In this work, amorphous B coated Mg nanopowder (BCMN) is synthesized and transport property of MgB2 superconducting wire is significantly enhanced with different contents of BCMN. BCMN has high reactivity since it contains nanoscale Mg and amorphous B. It allows to obtain MgB2 nanocrystals at only 400 °C with the compression of a lattice parameter and expansion of c lattice parameter compared to MgB2 formed by micron-sized Mg mixed with amorphous B (Mg + B) powders. These MgB2 nanocrystals serve as crystal nuclei and promote the crystallization and growth of MgB2. The mismatch of different lattice parameters prepared using BCMN and M + B powders induces low angle grain boundaries (LAGBs) embedded in MgB2 grains. LAGBs act as plane defects, leading to a dominant surface pinning mechanism and an enhancement in the critical current density on the magnetic field (J c(H)). At 4.2 K in 6 T, transport critical current density (J ct) of wire with 20 wt.% BCMN is 6.7 × 104 A·cm−2, approximately 1.8 times wire with 0 wt.% BCMN.

Enhancing structural integrity and adsorption performance of carbon nanotube buckypaper for water remediation through innovative densification strategy

The transformation of individual carbon nanotubes (CNTs) into buckypaper often results in random organization, leading to gaps or pores between them. These gaps act as flaws, reducing the overall properties of the bulk CNT structure. This study presents an advanced technique for densifying the structure by filling the gaps to tackle this issue. To achieve this, smaller multi-walled carbon nanotubes (MWCNTs) were employed to fill the gaps in the buckypaper composed of larger MWCNTs. This approach resulted in a significant improvement in the physical properties of the structure. The resulting hybrid buckypaper was thoroughly characterized using various techniques, including scanning electron microscopy, Raman spectroscopy, BET, XRD, and thermogravimetric analysis. The findings of this study demonstrated notable enhancements in the packing density, specific surface area, and tensile strength of the hybrid buckypaper, with improvements of 31.38 %, 63 %, and 20 %, respectively. Furthermore, the hybrid buckypaper proved to be an effective adsorbent for removing methylene blue dye from wastewater, exhibiting an impressive adsorption efficiency of 99.53 %. The absence of sludge impurities due to its high mechanical strength, combined with its superior rejuvenation capacity during multiple uses encourages cleaner and efficient water treatment system.

A Versatile C/Fe3O4/C Self‐Heating Electrode for Universal Application of Alternating Magnetic Fields in Electrocatalytic Hydrogen Production

AbstractThe high‐frequency alternating magnetic field (AMF) is considered as a fascinating heating treatment that provides a noninvasive solution to enhance the catalytic efficiency of electrocatalyst. However, practical applications of AMF in electrochemistry are primarily concentrated on magnetic mediums. To broaden its application into nonmagnetic catalysts, herein, a practicable method is reported by modifying the working electrode substrate with magnetic Fe3O4 nanoparticles (NPs), which serves as both substrate and self‐heating medium by virtue of its rapid and efficient magnetic heating effect associated with Néel relaxation triggered by external high‐frequency AMF, thus boosting the catalyst performance upon it. To verify it, Pt NPs and Pt single atoms (SAs), as two representative non‐magnetic catalyst, are selected for trials. The results, reveal that, when AMF is applied, Pt NPs@C/Fe3O4/C and Pt SAs@C/Fe3O4/C display remarkable enhancement of hydrogen evolution reaction magnetocurrent density respectively by ≈ 146% and ≈185%, whereas on unmodified bare glassy carbon there both show unnoticeable change in catalytic performance. The developed strategy opens up a vast space for exploiting the energy of a weak, non‐invasive magnetic field.

The Effects of Dietary Supplementation with Collagen and Vitamin C and Their Combination with Hyaluronic Acid on Skin Density, Texture and Other Parameters: A Randomised, Double-Blind, Placebo-Controlled Trial.

Collagen dietary supplements are becoming increasingly popular as a means to reduce signs of skin ageing. The objective of this three-way, randomised, placebo-controlled, double-blind study was to examine and contrast the effects of dietary supplementation with a daily dose of 5 g hydrolysed collagen with 80 mg of vitamin C (CP product) and their combination with 30 mg of hyaluronic acid (CPHA product) over 16 weeks. Validated methods were utilised for the objective evaluation of skin parameters. In total, 87 subjects (women, 40-65 years) completed the entire trial, distributed across the groups as follows: placebo group (n = 29), CPHA group (n = 28), and CP group (n = 30). The results showed beneficial effects of both test products, with notable enhancements in dermis density, skin texture, and a reduction in the severity of wrinkles. In contrast, the administration of either of the products did not yield any significant impacts on skin elasticity or hydration. Observation of the investigated skin parameters did not show superior effects of the addition of hyaluronic acid (HA) to collagen. Therefore, the ability of supplementation with HA to improve the effects on investigated skin parameters beyond the supplementation of collagen alone cannot be confirmed.

Optimizing production conditions of innovative bio-pellets developed from flax straw

The increasing global demand for sustainable energy has prompted the utilization of agricultural residues as viable alternatives to traditional fossil fuels. This study specifically focuses on the utilization of flax straw, a substantial by-product in Canadian agriculture, to produce innovative biofuels through the process of pelletization. To enhance the quality of the pellets, lignin extracted from flax straw was introduced as a novel and natural pellet binder. A comprehensive investigation was conducted to analyze effect of various parameters, including flax straw particle size, binder (lignin) content, moisture levels, and pelletization conditions on quality of produced pellets. It was observed that at a compressive force of 4000 N and a die temperature of 95 °C, pellets made from larger flax straw particles (300–355 µm) exhibited a density of 1016 kg/m³ and a mechanical durability of 26.4 %. Subsequently, by reducing the particle size to 75–106 µm, a marked enhancement in both density (1072 kg/m³) and durability (86.1 %, a 2.3-fold increase) was achieved. The incorporation of 10 % lignin into medium-sized flax straw particles (150–212 µm) increased pellet durability by 18.6 % from 73.5 % to 87.2 %. Introducing an optimal moisture content of 14 % to the flax straw resulted in a notable increase in both density (from 1036 to 1154 kg/m³) and durability (from 73.5 % to 90.6 %, a 23.3 % increase). Compressive force and die temperature positively affected pellet quality. Elevating the temperature from 75 to 115 °C in pellets made from 150 to 212 µm flax straw, modified with 10 % lignin and 14 % moisture content, led to a significant improvement in both density (1179 kg/m³) and durability (96.6 %, a 11.9 % increase). Physiochemical characteristics of flax straw, lignin, and the resulting pellets were explored using various techniques such as Fourier transform infrared, thermogravimetric analysis, and differential scanning calorimetry. These comprehensive investigations offer valuable insights for optimizing pellet materials and pelletization conditions and promoting the sustainable utilization of agricultural residues for bioenergy production.

Ferroelectric Material in Triboelectric Nanogenerator.

Ferroelectric materials, with their spontaneous electric polarization, are renewing research enthusiasm for their deployment in high-performance micro/nano energy harvesting devices such as triboelectric nanogenerators (TENGs). Here, the introduction of ferroelectric materials into the triboelectric interface not only significantly enhances the energy harvesting efficiency, but also drives TENGs into the era of intelligence and integration. The primary objective of the following paper is to tackle the newest innovations in TENGs based on ferroelectric materials. For this purpose, we begin with discussing the fundamental idea and then introduce the current progress with TENGs that are built on the base of ferroelectric materials. Various strategies, such as surface engineering, either in the micro or nano scale, are discussed, along with the environmental factors. Although our focus is on the enhancement of energy harvesting efficiency and output power density by utilizing ferroelectric materials, we also highlight their incorporation in self-powered electronics and sensing systems, where we analyze the most favorable and currently accessible options in attaining device intelligence and multifunctionality. Finally, we present a detailed outlook on TENGs that are based on ferroelectric materials.

Improved high voltage operation of amorphous In–Ga–Zn–O thin film transistor by carrier density enhancement

We report on improved high voltage operation of amorphous-In–Ga–Zn–O (a-IGZO) thin film transistors (TFTs) by increasing carrier density and distributing the high bias field over the length of the device which utilizes an off-set drain structure. By decreasing the O2 partial pressure during sputter deposition of IGZO, the channel carrier density of the high voltage a-IGZO TFT (HiVIT) was increased to ∼1018 cm−3. Which reduced channel resistance and therefore the voltage drop in the ungated offset region during the on-state. To further decrease the electric field in the offset region, we applied Ta capping and subsequent oxidation to locally increase the oxygen vacancy levels in the offset region thereby increasing local carrier density. The reduction of the drain field in the offset region from 1.90 V μm−1 to 1.46 V μm−1 at 200 V drain voltage, significantly improved the operational stability of the device by reducing high field degradation. At an extreme drain voltage of 500 V, the device showed an off-state current of ∼10−11 A and on-state current of ∼1.59 mA demonstrating that with further enhancements the HiVIT may be applicable to thin-film form, low leakage, high voltage control applications.

Enhancement of critical current densities by co-doping with Zr, Sn and Ce for Gd123 thin films fabricated by fluorine-free MOD method

Abstract We have fabricated GdBa2Cu3O7-δ thin films co-doped several types of BaMO3 (M=Zr, Sn, Ce) artificial pinning centers with different lattice constants and Young’s modulus from 2.0 to 5.0 mol% on LaAlO3 single crystal substrates by the FF-MOD method. When several types of BaMO3 are simultaneously introduced into Gd123 films by the FF-MOD method, Ba required for BaMO3 crystal growth is shared among them, each crystal growth is suppressed, and thus the crystals become finer and denser. This resulted in a remarkable enhancement of the critical current densities in magnetic fields. The maximum J c of 16.57 MA cm-2 at 0 T and 1.97 MA cm-2 at 3.0 T, 30 K obtained for the Gd123 film introduced three types of BaMO3 (M=Zr, Sn, Ce) with 4.0 mol% were 1.22 and 1.76 times larger than those for the film with the same amount of BaCeO3. This method shows a new strategy to improve Jc in magnetic fields of REBCO.

Dynamical friction in dark matter superfluids: The evolution of black hole binaries

The theory of superfluid dark matter is characterized by self-interacting sub-eV particles that thermalize and condense to form a superfluid core in galaxies. Massive black holes at the center of galaxies, however, modify the dark matter distribution and result in a density enhancement in their vicinity known as dark matter spikes. The presence of these spikes affects the evolution of binary systems by modifying their gravitational wave emission and inducing dynamical friction effects on the orbiting bodies. In this work, we assess the role of dynamical friction for bodies moving through a superfluid core enhanced by a central massive black hole. As a first step, we compute the dynamical friction force experienced by bodies moving in a circular orbit. Then, we estimate the gravitational wave dephasing of the binary, showing that the effect of the superfluid drag force is beyond the reach of space-based experiments like LISA, contrarily to collisionless dark matter, therefore providing an opportunity to distinguish these dark matter models.

Optimization of tensile properties and anisotropy in a cryogenically treated laser additively manufactured high entropy alloy

Repetitive deep cryogenic soaking treatment (DCT) of laser metal deposition (LMD) processed CrMnFeCoNi high entropy alloy (HEA) significantly enhances its strength without compromising ductility. This is attributed to the compressive stress induced nanotwin formation, which in turn facilitates twin induced plasticity. In this work, a parametric study on the effect of the residual stress profile and the DCT cycles on the tensile properties of the HEA, along the build and scan directions is conducted. Towards this end, builds fabricated with 5 different laser powers, 1100, 1400, 1700, 2000 and 2300 W, are examined and the ones with highest and lowest residual stress gradient are considered for further DCT treatments. Results indicate that the build fabricated with 1400 W laser power, which has the highest gradient in initial residual stresses, exhibits a greater enhancement in dislocation and twin density with increasing number of DCT treatments. Compared to its as-built state the peak yield and tensile strength of the HEA (along the scanning direction) increases to 592 ± 13 and 778 ± 15 MPa, without significant decrease in its ductility after 12 DCT cycles. However, the enhancement in the dislocation, twin density and therefore, the strength, is minimal after it is treated to 15 DCT cycles. Anisotropy in both strength and ductility, which is of the order of 20-25 %, is also observed in the DCT treated builds along the build and scan directions. These observations were rationalized on the basis of dislocation and twin evolution and distribution during DCT and deformation of the build when deformed in different directions. Implications of these results in the context of employing DCT for strengthening LMD fabricated HEA components are discussed.

Evolution of the Disk in the Be Binary δ Scorpii Probed during Three Periastron Passages

We examine the evolution of the disk surrounding the Be star in the highly eccentric 10.8 yr binary system δ Scorpii over its three most recent periastron passages. V-band and B − V photometry, along with Hα spectroscopy, are combined with a new set of extensive multiband polarimetry data to produce a detailed comparison of the disk's physical conditions during the time periods surrounding each closest approach of the secondary star. We use the three-dimensional Monte Carlo radiative transfer code HDUST and a smoothed particle hydrodynamics code to support our observations with models of disk evolution, discussing the behavior of the Hα and He i 6678 Å lines, V-band magnitude, and polarization degree. We compare the characteristics of the disk immediately before each periastron passage to create a baseline for the unperturbed disk. We find that the extent of the Hα emitting region increased between each periastron passage, and that transient asymmetries in the disk become more pronounced with each successive encounter. Asymmetries of the Hα and He i 6678 Å lines in 2011 indicate that perturbations propagate inward through the disk near periastron. When the disk’s direction of orbit is opposite to that of the secondary, the parameters used in our models do not produce spiral density enhancements in the Hα emitting region because the tidal interaction time is short due to the relative velocities of the disk particles with the secondary. The effects of the secondary star on the disk are short-lived and the disk shows independent evolution between each periastron event.

A Statistical Analysis of the Morphology of Storm‐Enhanced Density Plumes Over the North American Sector

AbstractThe storm‐enhanced density (SED) is a large‐scale midlatitude ionospheric electron density enhancement in the local afternoon sector, which exhibits substantial spatial gradients and thus can impose detrimental effects on modern navigation and communication systems, causing potential space weather hazards. This study has identified a comprehensive list of 49 SED events over the continental US and adjacent regions, by examining strong geomagnetic storms occurring between 2000 and 2023. The ground‐based Global Navigation Satellite System (GNSS) total electron content and data from a new TEC‐based ionospheric data assimilation system were used to analyze the characteristics of SED. For each derived SED events, we have quantified its morphology by employing a Gaussian function to parameterize key characteristics of the SED, such as the plume intensity, central longitude, and half‐width. A statistical analysis of SEDs was conducted for the first time to characterize their climatological features. We found that the SED distribution exhibits a higher peak intensity and a narrower width as geomagnetic activity strengthens. The peak intensity of SED has maximum values around the equinoxes in their seasonal distribution. Additionally, we observed a solar cycle dependence in the SED distribution, with more events occurring during the solar maximum and declining phases compared to the solar minimum. SED plumes exhibit a sub‐corotation feature with respect to the Earth, characterized by a westward drift speed between 50 and 400 m/s and a duration of 3–10 hr. These information advanced the current understanding of the spatial‐temporal variation of SED characteristics.

Carbon coated iron pyrite (C–FeS2) photo-electrode for photo-electrochemical water splitting

In this paper, we present fabrication of ‘FeS2’ and carbon coated FeS2 (C–FeS2) photo-electrodes and demonstrated that coating of carbon on FeS2 significantly enhanced photo-electrochemical properties. The hydrothermal method has been adopted for the synthesis of FeS2 and carbon coating on FeS2 was achieved by CVD technique. The materials are subsequently characterized using X-ray diffraction, Raman spectroscopy and Field enhanced scanning electron microscope (FESEM) techniques for phase identification and morphological studies, respectively. The photo-electrochemical measurements revealed significant enhancement in the current density from ∼2 to 3.7 mA/cm2 (∼1.8 times higher) for C–FeS2 in comparison to the FeS2 photo-electrode under visible light. The enhancement in FeS2 after carbon coating has been attributed to reduction in recombination of photo generated charge carriers, enhancement in the band bending and lowering the charge transfer resistance at the semiconductor/electrolyte interface. To date, very few studies have been reported on FeS2 based composites for water splitting applications and use of carbon coating can be a novel approach for developing efficient solar to hydrogen conversion devices. The mechanism for the photocurrent enhancement was supported by Mott-Schottky and electrochemical impedance spectroscopy measurements.

Influence of trapezoidal channel design on volume power density of ammonia-hydrogen fuel cells

Proton exchange membrane fuel cells based on ammonia decomposition gas (ammonia-hydrogen fuel cells) contain about 25% nitrogen at the anode, resulting in lower power density. In this paper, the volume power density enhancement effect of trapezoid channel with different upper edge length is studied. Research shows that the volume power density of trapezoid 0.1, 0.2, 0.4, 0.6 is increased by 53.5%, 62.0%, 81.9% and 108.3% compared with the conventional rectangular channel, respectively, and it is increased by 5.5%, 11.4%, 25.4% and 43.6% respectively, compared with the triangular channel. However, as the upper edge of the trapezoidal flow channel increases, the anode and cathode of the trapezoidal flow channel appear hydrogen hunger with a zero domain of up to 45% and the phenomenon of the horn mouth gradually moving forward respectively. Moreover, longer flow channels have lower fuel utilization efficiency, as low as 76%.

A Convenient In Situ Preparation of Cu2ZnSnS4-Anatase Hybrid Nanocomposite for Photocatalysis/Photoelectrochemical Water-Splitting Hydrogen Production.

This study details the rational design and synthesis of Cu2ZnSnS4 (CZTS)-doped anatase (A) heterostructures, utilizing earth-abundant elements to enhance the efficiency of solar-driven water splitting. A one-step hydrothermal method was employed to fabricate a series of CZTS-A heterojunctions. As the concentration of titanium dioxide (TiO2) varied, the morphology of CZTS shifted from floral patterns to sheet-like structures. The resulting CZTS-A heterostructures underwent comprehensive characterization through photoelectrochemical response assessments, optical measurements, and electrochemical impedance spectroscopy analyses. Detailed photoelectrochemical (PEC) investigations demonstrated notable enhancements in photocurrent density and incident photon-to-electron conversion efficiency (IPCE). Compared to pure anatase electrodes, the optimized CZTS-A heterostructures exhibited a seven-fold increase in photocurrent density and reached a hydrogen production efficiency of 1.1%. Additionally, the maximum H2 production rate from these heterostructures was 11-times greater than that of pure anatase and 250-times higher than the original CZTS after 2 h of irradiation. These results underscore the enhanced PEC performance of CZTS-A heterostructures, highlighting their potential as highly efficient materials for solar water splitting. Integrating Cu2ZnSnS4 nanoparticles (NPs) within TiO2 (anatase) heterostructures implied new avenues for developing earth-abundant and cost-effective photocatalytic systems for renewable energy applications.

Phenanthrene metabolism in Panicum miliaceum: anatomical adaptations, degradation pathway, and computational analysis of a dioxygenase enzyme.

Polycyclic aromatic compounds (PAHs) are persistent organic pollutants of environmental concern due to their potential impacts on food chain, with plants being particularly vulnerable. While plants can uptake, transport, and transform PAHs, the precise mechanisms underlying their localization and degradation are not fully understood. Here, a cultivation experiment conducted with Panicum miliaceum exposed different concentrations of phenanthrene (PHE). Intermediate PHE degradation compounds were identified via GC-MS analysis, leading to the proposal of a phytodegradation pathway featuring three significant benzene ring cleavage steps. Our results showed that P. miliaceum exhibited the ability to effectively degrade high levels of PHE, resulting in the production of various intermediate products through several chemical changes. Examination of the localization and anatomical characteristics revealed structural alterations linked to PHE stress, with an observed enhancement in PHE accumulation density in both roots and shoots as treatment levels increased. Following a 2-week aging period, a decrease in the amount of PHE accumulation was observed, along with a change in its localization. Bioinformatics analysis of the P. miliaceum 2-oxoglutarate-dependent dioxygenase (2-ODD) DAO-like protein revealed a 299 amino acid structure with two highly conserved domains, namely 2OG-FeII_Oxy and DIOX_N. Molecular docking analysis aligned with experimental results, strongly affirming the potential link and direct action of 2-ODD DAO-like protein with PHE. Our study highlights P. miliaceum capacity for PAHs degradation and elucidates the mechanisms behind enhanced degradation efficiency. By integrating experimental evidence with bioinformatics analysis, we offer valuable insights into the potential applications of plant-based remediation strategies for PAHs-contaminated environments.