Engine Thermal System Research Articles

Thermal balance performance simulation and optimization of full-ground crane cabins

To solve the excessive thermal load problem of the crane engine and engine compartment, a combined 1-D and 3-D thermal simulation method is developed to numerically simulate the heat flow field inside and outside the engine compartment, the engine thermal system and the cooling system. Simultaneously, to ensure the accuracy of the numerical calculation boundary and the feasibility of the combined thermal simulation method, the trailer heat balance test is conducted under the rated conditions and the maximum torque conditions. By reasonably sealing the heat dissipation assembly at the front of the nacelle, bottom guards under the engine are added and other improvement measures are taken. It is found that the engine outlet’s coolant temperature is decreased by 15.9 °C under rated conditions when the improved crane is in the 36 °C environment. While the outlet’s coolant temperature is decreased by 20 °C under maximum torque conditions.

Analysis of the Effect of Vehicle Platooning on the Optimal Control of a Heavy Duty Engine Thermal System

<div class="section abstract"><div class="htmlview paragraph">One promising method for reducing fuel consumption and emissions, particularly in heavy duty trucks, is platooning. As the distance between vehicles decreases, the following vehicles will experience less aerodynamic drag on the front of the vehicle. However, reducing the velocity of the air contacting the front of the vehicle could have adverse effects on the temperature of the engine. To compensate for this effect, the energy consumption of the engine cooling system might increase, ultimately limiting the overall improvements obtained with platooning. Understanding the coupling between drag reduction and engine cooling load requirement is key for successfully implementing platooning strategies. Additionally, in a Connected and Automated Vehicle (CAV) environment, where information of the future engine load becomes available, the operation of the cooling system can be optimized in order to achieve the maximum fuel consumption reduction. In this paper, a control-oriented physics-based model for the engine cooling loop of a Volvo engine is developed and validated against road data. Starting from the validated model, an optimal control problem for the coolant system is formulated considering the tradeoff between the tracking of the engine temperature setpoint and the corresponding fuel consumption under different trailing distances. To compare the coolant system performance, Dynamic Programming (DP) is used to determine the global optimal solution for the coolant system actuator. The coupling between optimal cooling system operation and reduction in ram air are evaluated by comparing the results obtained from the DP under different platooning conditions against the unrestricted scenario. In addition, the paper analyzes the changes in the tradeoff between fuel consumption and setpoint tracking for different vehicle distances. This analysis will provide useful insight on the sensitivity of the coolant system controller calibration to the platoon distance.</div></div>

Review of the systems analysis of interactions between the thermal, lubricant, and combustion processes of diesel engines

A review of technologies surrounding the thermal management system of the modern diesel engine with increased attention on fuel consumption is presented. A system-based approach has been adopted, looking at the interaction with other key systems. Previous innovation has aimed at reducing the power consumption of the cooling system or incorporating different cooling strategies and improving the engine warm-up rate for improved fuel consumption by higher operating temperatures. Electrical pumps can operate independently of the engine speed, and precision cooling and nucleate boiling have improved the heat transfer within the engine, reducing coolant flow requirements by 90 per cent. Improved warm-up rates have been demonstrated by using reduced thermal inertia or energy recovery systems either simulated on the test rig or through heat exchangers with exhaust gases. The resultant reduction in the fuel consumption is a result of various effects of the temperature on both the lubricating system and the combustion process. Despite difficulties in accurately measuring the engine friction, studies suggest that an increase in the engine temperature from 50°C to 80°C reduces the engine friction by 44 per cent because of 67 per cent lower oil viscosity. Simultaneous reduction in the emissions of nitogen oxides (NO x) and the fuel consumption of 13.5 per cent and 0.7 per cent respectively have been achieved by including the engine thermal system in the calibration procedure. However, in-cylinder data needs to be studied to understand fully the mechanisms involved. Hotter engine temperatures reduce ignition delay, making combustion occur earlier in the cycle, which has a positive effect on the fuel consumption but a negative effect on the NO x emissions. Engine thermal management requires a system-based approach if the effects are to be fully understood but offers potential as an additional parameter in engine calibration.