Energy Absorption Capability Research Articles

Crashworthiness Investigations for 3D-Printed Multi-Layer Multi-Topology Engineering Resin Lattice Materials.

In comparison to monolithic materials, cellular solids have superior energy absorption capabilities. Of particular interest within this category are the periodic lattice materials, which offer repeatable and highly customizable behavior, particularly in combination with advances in additive manufacturing technologies. In this paper, the crashworthiness of engineering multi-layer, multi-topology (MLMT) resin lattices is experimentally examined. First, the response of a single- and three-layer single topology cubic and octet lattices, at a relative density of 30%, is investigated. Then, the response of MLMT lattices is characterized and compared to those single-topology lattices. Crashworthiness data were collected for all topology arrangements, finding that while the three-layer cubic and octet lattices were capable of absorbing 9.8 J and 7.8 J, respectively, up to their respective densification points, the unique MLMT lattices were capable of absorbing more: 19.0 J (octet-cube-octet) and 22.4 J (cube-octet-cube). These values are between 94% and 187% greater than the single-topology clusters of the same mass.

Inverse design of cellular structures with the geometry of triply periodic minimal surfaces using generative artificial intelligence algorithms

Triply periodic minimal surfaces (TPMS) exhibit excellent mechanical and energy absorption properties due to their structural advantages. However, existing porous TPMS structural design methods are constrained to a forward process from structural parameters to mechanical properties. This study proposed an inverse design method that combines bidirectional generative adversarial networks (BiGAN) and mechanical performance targets, resulting in a combined TPMS structure of Primitive and IWP types with superior buffering and energy absorption capabilities. The results show that under a single load value target condition of the designed structure, the minimum deviation index (R2) between the load value corresponding to the displacement point and the target load value is only 0.987, and the maximum mean absolute percentage error (MAPE) is only 5.92 %. When considering the elastic modulus target, the approach successfully conducts two sets of combined structural designs meeting the requirements of both high and low elastic moduli. When targeting the specified load-displacement curve conditions, specifically when combining high elastic modulus with ascending plasticity, the designed structures exhibit an error of only 2.2 % compared to the target property. Moreover, the quasi-static uniaxial compression experiments conducted on additively manufactured designed structures confirm that the experimental curves match the target curves in terms of deformation trends and load value ranges. The success of this inverse design approach for cellular TPMS structures has the potential to expedite new structural material development processes.

Novel auxetic metamaterials inspired from geometry patterns of an Iranian Mosque with improved energy absorption capability

Recent developments in auxetic metamaterials have positioned them as highly effective energy absorbers, offering superior energy absorption and specific energy absorption (SEA) properties. Meanwhile, the fascinating geometric patterns and motifs found in historical arts have emerged as a valuable source of inspiration for designing innovative auxetic unit cells. This research proposes a novel auxetic unit cell inspired by the geometric patterns exhibited in the Isfahan Jameh Mosque in Iran. Two distinct auxetic structures are designed with different arrangements of the proposed unit cell and fabricated via the fused deposition modeling (FDM) additive manufacturing technology. Their negative Poisson’s ratio (NPR), energy absorption capability, and SEA are evaluated through both experimental testing and finite element method (FEM). The comparative analysis of the results shows that the designed structures exhibit significantly enhanced energy absorption compared to the other two different re-entrant auxetic structures. Consequently, these novel auxetic structures hold great promise in replacing conventional re-entrant structures as highly efficient energy absorber devices.

Energy absorption properties of origami‐based re‐entrant honeycomb sandwich structures with CFRP subjected to low‐velocity impact

AbstractThis paper investigates a honeycomb sandwich structure that draws inspiration from the craft of origami. A specific folding pattern was applied to the honeycomb to create the origami‐based re‐entrant honeycomb (ORH), aimed at improving the energy absorption properties of the sandwich structure. The study on the energy absorption properties of structures under low‐velocity impact (LVI) utilized both experimental and numerical approaches. The energy absorption properties of the sandwich structure were examined by conducting LVI tests with different impact energy and then compared to the mechanical properties of the traditional re‐entrant honeycomb sandwich structures (TRHSS). Additionally, a refined finite element model has been established and its accuracy verified. Numerical studies were conducted to explore the effects of structural parameters on the energy absorption properties of ORH sandwich structure (ORHSS). The results show that the ORHSS exhibited a significant reduction in peak force when subjected to LVI, in contrast to the TRHSS. Furthermore, the ORHSS exhibit significant efficiency in energy absorption. Enhancing the wall thickness or folding angle can significantly improve the energy absorption properties of the ORHSS, thereby boosting the honeycomb's contribution to this process. This optimization results in an improved absorptive effect of the structure. The findings offer new recommendations for developing lightweight absorbent materials with potential applications across various industries.Highlights A novel composite sandwich structure serves as an efficient device for absorbing energy. This sandwich structure exhibits excellent cushioning and energy absorption capabilities. Changing geometric parameters can enhance the impact performance of the structure. A larger folding angle makes the core more prone to deformation. The greater the forward length of the ORH, the lower specific energy absorption (SEA) of the ORHSS.

Dynamic Response of Gradient Aluminum Foam Sandwich Tubes under External Explosive Loads.

In this paper, we numerically investigate the dynamic response and explosion resistance of gradient aluminum foam sandwich tubes subjected to external blast loads. Based on 3D-Voronoi technology, we construct density-graded aluminum foam cores to systematically explore the influence of core density distribution, density gradient, and average relative density on the protective performance of these structures. Our primary objective is to identify optimal design parameters that maximize explosion mitigation capabilities while balancing energy absorption and specific energy absorption capacities. The research results show that a positive gradient core configuration exhibits superior anti-explosion performance, significantly outperforming its uniform and negatively graded counterparts, particularly when the gradient value is substantial. For the positive gradient cores, an increase in the gradient value leads to a corresponding enhancement in explosion resistance. Conversely, in negatively graded cores, a higher gradient value diminishes the anti-explosion performance. Furthermore, while augmenting the relative density of the core layer does improve the overall explosion resistance of the sandwich tube, it comes at the cost of reduced energy absorption and specific energy absorption capabilities, highlighting the need for a delicate balance among these competing factors.

Crushing responses and energy absorption characteristics of the dynamic stiffening porous material subjected to different strain rates

Porous material (PM) has excellent energy absorption performance and is widely used as an impact-energy absorber. However, the PM may provide little utility when the impact conditions change. Shear stiffening gel (SSG) with an extremely strong viscosity effect can be as a dynamic responding fortifier to overcome the limitation of PMs. In this paper, a rate-dependent, smart energy-absorbing material (SSG/PM) is fabricated by incorporating SSG that is reinforced with CaCO3 particles onto the PM. Aided by the dynamic compression experiments at the strain rate range of 0.001 to 100 s−1, both SSG/PM and neat PM are assessed and compared for crushing performance. Results reveal that the SSG/PM exhibits a pronounced dynamic stiffening characteristic in response to various strain rates owing to the rate-dependent phase transition of embedded SSG, thereby contributing to enhancing the PM skeleton's ability to withstand deformation. The SSG/PM displays a noteworthy boost in energy absorption (up to 831.98 %). Moreover, the influence of loading rate, particle mass fraction, and PM aperture size are also examined. The findings indicate that its crushing resistance and energy absorption capability are enhanced with the increase in strain rate, demonstrating the ability to adapt to various dynamic scenarios. The use of a higher particle mass fraction and smaller aperture size helps to improve the energy absorption capability of the SSG/PM. Additionally, quantitative energy analysis is implemented in which the energy dissipation mechanisms of the SSG/PM are attributed to the synergistic interaction of skeleton deformation, shear stiffening effects, and particle enhancement. It is ascertained that as the loading rate increases, the shear stiffening effect continues to strengthen; the particle content effect exhibits a rising-falling trend; while the skeleton deformation shows a rate-independent feature. This study sheds light on the crushing behaviors and corresponding energy dissipation mechanisms of SSG-based composites, thereby providing valuable insights for the design of SSG-based composites.

Soft Magnetoelastic Tactile Multi-Sensors with Energy-Absorbing Properties for Self-Powered Human-Machine Interfaces.

Tactile sensors play a key role in human-machine interfaces (HMIs) for augmented and virtual reality, point-of-care devices, and human-robot collaboration, which show the promise of revolutionizing our ways of life. Here, we present a sensor (EMTS) that utilizes the magnetoelastic effect in a soft metamaterial to convert mechanical pressure into electrical signals. With this unique mechanism, the proposed EMTS simultaneously possesses self-powering, waterproof, and compliant features. The soft metamaterial is essentially a porous magnetoelastomer structure designed based on the Fourier series expansion, which allows for programmable mechanical response and sensing performance of the EMTS. Fabricated by simple 3D-printed molds, the EMTS also holds potential for low-cost production. Particularly, the porous magnetoelastomer structure comes with selectable buckling instabilities that can significantly enhance biomechanical-to-electrical energy conversion. Also, with the embedded magnetic microparticles, the energy-absorbing performance of the sensor is greatly improved, which is highly beneficial to HMIs. To pursue practical applications, the EMTSs are further integrated with two systems as control and perception modules. It is demonstrated that the EMTS is able to identify different hand gestures to control a lighting system even in a high-humidity environment. Also, the EMTS stands out for its superior capability of simultaneous impact perception and energy absorption in drop tests. Overall, with its compelling array of features, the presented EMTS gives impetus to multi-sensing technology and practically enables a variety of HMI applications.

Laser Powder Bed Fusion of Multifunctional Bio-inspired Vertical Honeycomb Sandwich Structures: For the Application of Lightweight Bipolar Plates of Proton Exchange Membrane Fuel Cells

The bipolar plate (BPP) is a crucial component of proton exchange membrane fuel cells (PEMFC). However, the weight of BPPs can account for around 80% of a PEMFC stack, posing a hindrance to the commercialization of PEMFCs. Therefore, the lightweight design of BPPs should be considered as a priority. Honeycomb sandwich structures meet some requirements for bipolar plates, such as high mechanical strength and lightweight. Animals and plants in nature provide many excellent structures with characteristics such as low density and high energy absorption capacity. In this work, inspired by the microstructures of the Cybister elytra, a novel bio-inspired vertical honeycomb sandwich (BVHS) structure was designed and manufactured by laser powder bed fusion (LPBF) for the application of lightweight BPPs. Compared with the conventional vertical honeycomb sandwich (CVHS) structure formed by LPBF under the same process parameters setting, the introduction of fractal thin walls enabled self-supporting and thus improved LPBF formability. In addition, the BVHS structure exhibited superior energy absorption (EA) capability and bending properties. It is worth noting that, compared with the CVHS structure, the specific energy absorption (SEA) and specific bending strength of the BVHS structure increased by 56.99% and 46.91%, respectively. Finite element analysis (FEA) was employed to study stress distributions in structures during bending and analyze the influence mechanism of the fractal feature on the mechanical properties of BVHS structures. The electrical conductivity of structures were also studied in this work, the BVHS structures were slightly lower than the CVHS structure. FEA was also conducted to analyze the current flow direction and current density distribution of BVHS structures under a constant voltage, illustrating the influence mechanism of fractal angles on electrical conductivity properties. Finally, in order to solve the problem of trapped powder inside the enclosed unit cells, a droplet-shaped powder outlet was designed for LPBF-processed components. The number of powder outlets was optimized based on bending properties. Results of this work could provide guidelines for the design of lightweight BPPs with high mechanical strength and high electrical conductivity.

Computer Simulation of Deformation characteristics of Hybrid Orthotropic Composite Sandwich Beams Under Bending and Axial Loading

This study focuses on the deformation characteristics of hybrid orthotropic composite sandwich beams under axial and bending loading. The homogeneous cores of the hybrid orthotropic sandwich beams affect different parameters on structures. We followed by analytically determining effective material properties to study response of the hybrid sandwich beam under axial and bending loading. Ensuing, we programmed all steps and procedures of solution algorithm into commercially available MATLABTM 2020 code to simulate practical scenarios. Subsequently, we collected and processed data in tabular and graphical forms to facilitate analyses. We compared simulation generated results to the data results available in the literature and found to be within the acceptable range of (±6%) deviations. We observed that the hybrid structure beams had undergone less deformation that confirmed that the hybrid structure beams have comprehensive mechanical advantages as well as has high strength and specific energy absorption capabilities. Based on comparison of the results, the hybrid beams are more damage resistant and tolerant than beams made of the other type of materials. Since hybrid sandwich beams are relatively light, economical, and perform better under axial and bending deformations. Therefore, this study could also be extended to investigate performance of the orthotropic sandwich beam structures under multiple loading directions as well as proposes that the usage of the hybrid sandwich beam components will be useful in global structures.

Analysis of Mechanical Properties and Parameter Dependency of Novel, Doubly Re-Entrant Auxetic Honeycomb Structures.

This study proposes a new, doubly re-entrant auxetic unit-cell design that is based on the widely used auxetic honeycomb structure. Our objective was to develop a structure that preserves and enhances the advantages of the auxetic honeycomb while eliminating all negative aspects. The doubly re-entrant geometry design aims to enhance the mechanical properties, while eliminating the buckling deformation characteristic of the re-entrant deformation mechanism. The effects of the geometric modification are described and evaluated using two parameters, offset and deg. A series of experiments were conducted on a wide range of parameters based on these two parameters. Specimens were printed via the vat photopolymerization process and were subjected to a compression test. Our aim was to investigate the mechanical properties (energy absorption and compressive force) and the deformation behaviour of these specimens in relation to the relevant parameters. The novel geometry achieved the intended properties, outperforming the original auxetic honeycomb structure. Increasing the offset and deg parameters results in increasing the energy absorption capability (up to 767%) and the maximum compressive force (up to 17 times). The right parameter choice eliminates buckling and results in continuous auxetic behaviour. Finally, the parameter dependency of the deformation behaviour was predicted by analytical approximation as well.

Additive manufactured high-performance topology-optimized lattice structure: Compressive behavior and flow heat transfer characteristics

In this study, topological optimization techniques were employed to construct innovative TopS lattice structures, to achieve a lightweight design while simultaneously optimizing their mechanical properties and enhancing flow and heat transfer performance. Through model reconstruction and proportional scaling techniques, lightweight configurations with increased surface areas were achieved, leading to the successful fabrication of Ti-6Al-4V lattice structures via Laser Powder Bed Fusion (LPBF) technology. A comprehensive investigation combining numerical simulations and experimental testing revealed that the TopS-L16 lattice structure outperforms TopS-L1 and TopS-L4 in terms of compressive strength, demonstrating values of 386.00 MPa for compressive strength, 352.00 MPa for upper compressive yield strength, and 6938.00 MPa for elastic modulus. Furthermore, multilayer-filled lattice structures were found to effectively improve streamline distribution and vorticity, reducing boundary layers, which indicates a significant enhancement in fluid flow and heat transfer performance, with TopS-L16 exhibiting the best performance. The novelty of this work lies in its exploration of the interplay between lattice structures and their interactions with compressive deformation, energy absorption capabilities, and flow heat transfer.

The Influence of Wave Characteristics, Tides, and Installation Conditions of L-Shaped OWC Wave Energy Converter on Energy Absorption Capability

The Influence of Wave Characteristics, Tides, and Installation Conditions of L-Shaped OWC Wave Energy Converter on Energy Absorption Capability

Production of rubberized concrete utilizing reclaimed asphalt pavement aggregates and recycled tire steel fibers

The integration of waste tire elements into concrete, specifically granular rubber and discrete steel fibers, signifies a substantial advance in the pursuit of sustainable alternatives for rigid concrete pavements. This incorporation not only improves the ductility of rigid concrete pavements, but also augments their energy absorption capabilities. Similarly, replacing natural aggregates in concrete with reclaimed asphalt pavement (RAP) aggregates makes a large contribution to the reduction of negative environmental impacts, while conserving natural resources from depletion. This investigation explores the potential application of recycled rubber particles from waste tires (WTRR) and RAP aggregates as partial substitutes for natural fine aggregates, and evaluates their impact on the performance of rigid concrete pavements. Eight mixes were cast, each with two variables: (i) fine aggregate type (fine rubber (FRu) aggregates, fine asphalt (FAs) aggregates, and combinations of both types of aggregate) replacing 50 % of the natural fine aggregate; and (ii) waste tire recycled steel fibers (WTRSF) content (0 and 40 kg/m3). The axial compressive stress–strain, flexural load–deflection, and direct shear strength behaviors, together with the dry unit weight and volume of permeable voids for all concrete mixes were investigated and compared. The results show that, although the flexural and shear strengths decrease with the inclusion of FRu and/or FAs, the use of WTRSF noticeably mitigates the losses in strength that arise from the use of WTRR and/or RAP aggregates alone. The inclusion of WTRSF enhances the strain capacity of the concrete and allows the development of adequate post-peak energy absorption capacity in flexural and shear loading. Additionally, the dry unit weight of the proposed composites decreased by as much as 8 %, and their volume of permeable voids lies within the limits of high-durability concrete mixes (9–12 %). Hence, the proposed sustainable concrete composites are promising composites for rigid concrete pavement construction.

Comparison of Energy Absorptive Capacities of Different Aluminum Alloy Foams Placed Inside the Crash Box

Increasing population worldwide and the resulting increasing number of automobiles increase the risk of traffic accidents. Due to this increasing risk, automobile manufacturers take various safety measures to protect drivers and passengers in case of possible accidents. Crash boxes are one of the passive safety system elements that are the first to absorb the impact in the event of a front or rear impact accident, absorbing the resulting deformation energy and ensuring that it is transmitted into the car at the least possible level. Therefore, increasing the energy absorption ability of crash boxes is an extremely important issue. In this study, it was aimed to increase the energy absorption capabilities by placing aluminum foam based materials produced by using the powder metallurgy method using three different aluminum alloys (Al2024, Al5083, and Al6061) inside the crash boxes, which are normally manufactured as hollow. In addition, the produced aluminum foams were compared in terms of pore sizes with SEM images. It can be said that Al6061 is the most ideal material among the alloys used in terms of pore structure and homogeneity. On the other hand, Al6061 alloys produced the greatest damped energy value within the parameters of the investigation, 221.711 J. This value was 169.556 J for Al2024 alloy and 214.101 J for Al5083 alloy. As a result, it was concluded that the amount of energy absorption can be increased by about 4-5 times by using metallic foams produced using aluminum materials compared to the empty crash box.

An experimental and numerical investigation of ballistic penetration behaviors of deployable composite shells

Bistable composite shells are suitable candidates for deployable space structures due to high stiffness to weight ratio as well as large volume reduction. Nevertheless, impact performance of bistable composite shells conflicting with space debris have been rarely studied. In this paper deployable hybrid composites constructed with combinations of carbon–carbon, carbon–kevlar, kevlar–kevlar, high-energy-absorption graphene-reinforced polyurethane elastomers are developed, and their ballistic penetration behaviors are experimentally and computationally studied. The influences of ballistic velocity on the absorbed energy, the residual velocity and damage morphology of the targets are investigated in both deployed and coiled stable states. The results show that severe local damages were observed for the carbon–carbon and carbon–kevlar samples after penetration with various velocities even first cosmic velocity, and the sample of deployable hybrid composite shell yielded the best ballistic impact resistance. The total energy absorption performance of the hybrid composite structure was greatly improved by introducing graphene-reinforced polyurethane elastomers without losing the deployability. Additionally, investigation on the energy absorption capability of deployed laminated shells with various curvature radii indicated that the curvature radius had a significant effect on the anti-penetration performance.

Energy Absorption Behavior of Carbon-Fiber-Reinforced Plastic Honeycombs under Low-Velocity Impact Considering Their Ply Characteristics.

Honeycomb structures made of carbon-fiber-reinforced plastic (CFRP) are increasingly used in the aerospace field due to their excellent energy absorption capability. Attention has been paid to CFRP structures in order to accurately simulate their progressive failure behavior and discuss their ply designability. In this study, the preparation process of a CFRP corrugated sheet (half of the honeycomb structure) and a CFRP honeycomb structure was illustrated. The developed finite element method was verified by a quasi-static test, which was then used to predict the low-velocity impact (LVI) behavior of the CFRP honeycomb, and ultimately, the influence of the ply angle and number on energy absorption was discussed. The results show that the developed finite element method (including the user-defined material subroutine VUMAT) can reproduce the progressive failure behavior of the CFRP corrugated sheet under quasi-static compression and also estimate the LVI behavior. The angle and number of plies of the honeycomb structure have an obvious influence on their energy absorption under LVI. Among them, energy absorption increases with the ply number, but the specific energy absorption is basically constant. The velocity drop ratios for the five different ply angles are 79.12%, 68.49%, 66.88%, 66.86%, and 60.02%, respectively. Therefore, the honeycomb structure with [0/90]s ply angle had the best energy absorption effect. The model proposed in this paper has the potential to significantly reduce experimental expenses, while the research findings can provide valuable technical support for design optimization in aerospace vehicle structures.

Impact Resistance Performance and Damage Characteristics of Mortise-and-Tenon Joint Prefabricated Bridge Piers

The mortise-and-tenon joint prefabricated connection combines the assembly form of mortise-and-tenon joints and cast-in-place wet joints. It achieves reliable joint connections through small joint depths and lap-spliced reinforcement lengths. To study the impact resistance and damage characteristics of the assembled pier, a nonlinear finite element analysis was performed on the assembled and monolithic pier model piers to study the effects of mortise-and-tenon joint depths, lap reinforcement, and grout on the response of the piers to vehicle impact. The results showed that, after impact, the damage to the prefabricated pier was similar to that of the monolithic one. The failure mode involved opening of the seam at the impact face-pier bottom junction and localized concrete compression at the back-impact face pier bottom, and damage accumulated from the column base towards the column centerline. The mortise-and-tenon joint provided substantial horizontal constraint for the pier, imparting excellent resistance to lateral stiffness. Consequently, both piers showed nearly identical peak impact forces, yet the prefabricated pier exhibited a lesser degree of bending deformation compared to the monolithic one. The depth of the mortise-and-tenon joints was a critical factor affecting the impact response of the prefabricated bridge pier. When the depth reached 0.4D or more, it ensured good impact resistance and joint connection, enhancing energy absorption capability and reducing pier damage. The length of lap-spliced reinforcement significantly affected the overall integrity of prefabricated component connections. Lap lengths of 10d or more greatly reduced the probability of failure in the connection between pier columns and cap beams, lowering damage to the pier columns, joints, and pier cap beams, thus ensuring good impact resistance. The diameter of the lap-spliced reinforcement and the elastic modulus of the grouting material affected the local stiffness near the joints. Increasing the diameter of the lap-spliced reinforcement appropriately prevented excessive local damage, while altering the elastic modulus had minimal impact on improving pier damage.

Strengthening and embrittlement effect of cryogenic temperature on fiber reinforced geopolymer composite

Understanding the cryogenic behaviour of geopolymer composite (GPC) is essential to implement them in real structural elements at cryogenic temperatures. The paper presents a comprehensive investigation on the compressive strength, flexural behaviours, and energy absorption capability of both plain GPC and fiber-reinforced geopolymer composite (FRGPC) containing different fiber types and contents subjected to in-situ −170 °C. The results demonstrate that the compressive strength of plain GPC and FRGPC increases by 104.9 %–213.6 %, and the flexural strength increases by 73.4 %–212.5 %, exhibiting a significant cryogenic strengthening effect. Moreover, compared to flexural strength, compressive strength of GPCs displays a higher sensitivity to the cryogenic strengthening effect. The failure mode of FRGPCs changed from ductile failure to ductile-brittle failure at −170 °C, which is due to the decreased ductility induced by the cryogenic embrittlement effect. Additionally, cryogenic exposure has a greater impact on reducing the ductility of FRGPCs containing PP fibers than those with steel fibers. However, the negative effects of cryogenic embrittlement effect on ductility can be mitigated by incorporating steel fibers and increasing fiber content. The further analysis reveals that strengthening and embrittlement effect are associated with the increased cumulative energy and the sudden release of local energy, respectively. These findings contribute to the understanding of GPC performance at cryogenic temperature, which can guide the development of more resilient and durable GPC for cryogenic applications.

Optimization of crashworthiness design of foam-filled crash boxes under oblique loading for electric vehicles

To increase the energy-absorbing capability of frontal collision management systems and improve vehicle crash safety, foam-filled crash boxes should be optimized. On the basis of a double tubular construction, a novel foam-filled crash box with a different design is developed. The energy absorption capacity, initial peak force, and deformation modes of the original and improved crash boxes were examined using impact models. As opposed to the full-filling design, it is demonstrated that the filling design may utilize less foam while increasing specific energy absorption. The stability of continuing deformation after the first buckling is determined by the foam-filled crash box. For the foam-filled crash box, a better-optimized design technique is suggested using the Taguchi method and principal component analysis (PCA). Compression tests are used to validate the design concept. Therefore, the optimal design technique of the crash box is suitable and practical for the crashworthiness design of crash boxes, considering the combined effect of significant indicators for electric vehicles.

Simulating loading–unloading hysteretic behaviors of nematic-genesis polydomain nematic elastomers

Nematic elastomers (NEs) are lightly cross-linked elastomers with nematic mesogens integrated in their polymer networks. Combination of large deformation capability with nematic-isotropic phase transition enables NEs to be the most promising soft materials for impact attenuation, actuation and soft robotics. In this paper, we focus on nematic-genesis polydomain NEs (N-PNEs) where mesogens are cross-linked at nematic states. N-PNEs are capable of absorbing and dissipating energy and easy to synthesize. We present a Voronoi diagram-based finite element model for specimen-scale N-PNEs, and investigate the cyclic tensile and compressive behaviors of N-PNEs at different strain rates. Our simulations reveal a smooth polydomain-monodomain transition during loading, accompanied by a full recovery of polydomain texture after the load is removed, indicating a memory effect of initial disordered mesogen alignment. The predicted behaviors align well with experimental observations, which validates our model. Furthermore, we assess the energy absorption and dissipation capabilities of N-PNEs compared to monodomain NEs, identifying conditions where N-PNEs exhibit superior performance. This study not only enhances our understanding of polydomain-monodomain transitions in N-PNEs, but also lays the groundwork for the development of N-PNE-based energy absorbers.