Elliptical Field Research Articles

Flow-field characteristics of the thermal plume above an elliptical high-temperature heat source surface

The thermal plume formed by the high-temperature elliptical heat source surface during the smelting process is often captured and removed by the local exhaust system. Accurately mastering the flow-field characteristics of such high-temperature elliptical heat plumes is helpful for efficient design of local exhaust systems. In this paper, the effects of the ratio of long and short axes (5/4 ≤ ξ ≤ 5/1) and the intensity of heat source (80 ≤ F ≤ 160 W) on the axial and radial velocity distribution of thermal plume in an elliptical heat source are investigated by numerical simulation combined with experimental validation. The results show that in the range of ξ ≤ 5/1, the axial dimensionless velocity distribution of the elliptical plume field and the spreading range of the plume field are mainly affected by ξ instead of F. For 5/4 ≤ ξ ≤ 5/1, the maximum axial velocity Um appears at 1.7 to 2.7 times Z/L (plume height to heat source long axis ratio). For ξ ≤ 5/2, the height at which the cross-sectional velocity field transitions to a circular distribution aligns with the height of Um. It is found that the plume velocity field is characterized by applying the point source model for ξ ≤ 5/3, and vice versa for the linear source model. The plume flow rate formulation obtained by modifying the linear source model for ξ > 5/3 has a better predictive ability in the Z/L ≤ 5 region. This study provides a reference for the design of ventilation systems for elliptical surface heat sources.

Bone density of the cervical, thoracic and lumbar spine measured using Hounsfield units of computed tomography – results of 4350 vertebras

IntroductionThe assessment of bone density has gained significance in recent years due to the aging population. Accurate assessment of bone density is crucial when deciding on the appropriate treatment plan for spinal stabilization surgery. The objective of this work was to determine the trabecular bone density values of the subaxial cervical, thoracic and lumbar spine using Hounsfield units.Material and methodsData from 200 patients who underwent contrast-enhanced polytrauma computed tomography at a maximum care hospital over a two-year period were retrospectively analyzed. HUs were measured with an elliptical measurement field in three different locations within the vertebral body: below the upper plate, in the middle of the vertebral body, and above the base plate. The measured Hounsfield units were converted into bone density values using a validated formula.ResultsThe mean age of the patient collective was 47.05 years. Mean spinal bone density values decreased from cranial to caudal (C3: 231.79 mg/cm3; L5: 155.13 mg/cm3; p < 0.001), with the highest values in the upper cervical spine. Bone density values generally decreased with age in all spinal segments. There was a clear decrease in values after age 50 years (p < 0.001).ConclusionsIn our study, bone density decreased from cranial to caudal with higher values in the cervical spine. These data from the individual spinal segments may be helpful to comprehensively evaluate the status of the spine and to design a better preoperative plan before instrumentation.

NuSEA: Nuclei Segmentation With Ellipse Annotations.

Nuclei segmentation is a crucial pre-task for pathological microenvironment quantification. However, the acquisition of manually precise nuclei annotations for improving the performance of deep learning models is time-consuming and expensive. In this paper, an efficient nuclear annotation tool called NuSEA is proposed to achieve accurate nucleus segmentation, where a simple but effective ellipse annotation is applied. Specifically, the core network U-Light of NuSEA is lightweight with only 0.86 M parameters, which is suitable for real-time nuclei segmentation. In addition, an Elliptical Field Loss and a Texture Loss are proposed to enhance the edge segmentation and constrain the smoothness simultaneously. Extensive experiments on three public datasets (MoNuSeg, CPM-17, and CoNSeP) demonstrate that NuSEA is superior to the state-of-the-art (SOTA) methods and better than existing algorithms based on point, rectangle, and text annotations. With the assistance of NuSEA, a new dataset called NuSEA-dataset v1.0, encompassing 118,857 annotated nuclei from the whole-slide images of 12 organs is released. NuSEA provides a rapid and effective annotation tool for nuclei in histopathological images, benefiting future explorations in deep learning algorithms.

Investigation of heat transfer characteristics of deflected elliptical-tube heat exchanger in closed-circuit cooling towers

The core component in a closed-circuit cooling tower is the heat exchanger consisting of bundles of heat transfer tubes. To improve the heat transfer performance of closed-circuit cooling towers, this paper studies the elliptical-tube heat exchanger in closed-circuit cooling towers and proposes a deflected elliptical tube and its optimized tube. This study uses a combination of experiments and simulations to experimentally compare the heat transfer performance of elliptical tube heat exchangers in closed-circuit cooling towers under different operating conditions and simulation comparison and analysis of different wind speeds, spray water flow rate under the influence of the three elliptical tube flow field characteristics and heat transfer performance. The results show that in the wind speed of 2–3.2 m/s, due to the shortening of the tube bundle spacing, the growth rate of the heat transfer coefficient of the elliptical deflection optimized tube bundle is 16.27 %. The heat transfer performance of the deflected elliptical optimized tube is better than that of the elliptical tube and deflected elliptical tube, while the application of the optimized tubes shortens the overall unit structure by 24.03 %, which can reduce the material consumption of the closed cooling tower.

Coverage Analysis for Elliptical-Orbit Satellites Based on 2-D Map

This paper proposes a geometric-based method of the ground-point visibility from a satellite or satellite constellation in elliptical orbit considering the <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">J</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> perturbation. First, the field-element equations describing the relationship between the elliptical satellite orbit, field parameters, and ground point are introduced and can be solved semi-analytically. Also, using a two-dimensional map composed of the mean argument of latitude and geographic longitude of the ascending node, the problem of calculating visible intervals is transformed into a simple intersection problem of a group of parallel lines and a time-invariant region generated by the field-element equations. Furthermore, based on the geometric relationship between any two satellites, the relative field mapping and constellation field mapping are described, which can simplify the multi-satellite coverage problem to a single-satellite coverage problem and can be used to obtain the coverage performance of the constellation analytically and rapidly for the target. The simulation results demonstrate that the proposed method is rapid, efficient, intuitive, and accurate, suggesting its wide applications in constellation studies <bold xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">.</b>

Strong polarization-controlled terahertz generation by bi-elliptical polarized laser fields

Terahertz generation from atoms driven by two color linearly polarized (LP) and circularly polarized (CP) laser fields have been well investigated. In this work, based on the photocurrent model, we investigate theoretically the intensity and polarization characteristics of terahertz waves radiated by the bi-elliptical polarized two-color laser fields with orthogonal or parallel major axes. We show that polarization-controlled, including circularly polarized terahertz waves with sufficient intensity comparable to that of co-rotating CP or parallel LP laser field, can be generated by using a longer-wavelength few-cycle bi-elliptical field. Our simulations also show that THz energy and ellipticity can be dramatically improved with dual-color elliptical field with tiny or large ellipticity, compared with that with two-color orthogonal LP field and counter-rotating CP laser field, respectively. Bi-elliptical polarized laser field provides a huge parameter space allowing for far-reaching control of THz emission.

Increased flexibility and efficiency of a double-scattering FLASH proton beamline configuration for in vivo SOBP radiotherapy treatments

Objective. To commission a proton, double-scattering FLASH beamline by maximizing efficiency and field size, enabling higher-linear energy transfer FLASH radiotherapy to cells and small animals using a spread-out Bragg peak (SOBP) treatment configuration. We further aim to provide a configuration guide for the design of future FLASH proton double-scattering (DS) beamlines. Approach. Beam spot size and spread were measured with film and implemented into TOol for PArticle Simulation (TOPAS). Monte Carlo simulations were optimized to verify the ideal positioning, dimensions, and material of scattering foils, secondary scatterers, ridge filters, range compensators, and apertures. A ridge filter with three discrete heights was used to create a spread-out Bragg peak (SOBP) and was experimentally verified using our in-house experimental FLASH beamline. The increase in dose rate was compared to nominal shoot-through techniques. Results. The configuration and scatterer distance producing the largest field size of acceptable flatness, without drastically compromising dose rate was determined to be an elliptical field of 2 cm × 1.5 cm (25% larger than a previous configuration). SOBP testing yielded three distinct but connected spikes in dose with flatness under 5%. Reducing the thickness of the (first) scattering foil by a factor of two was found to increase efficiency by 50%. The new settings increased the field size, provided a Bragg peak treatment option, and increased the maximum available dose rate by 85%, as compared to the previous, shoot through method. Significance. Beam line updates established FLASH dose rates of over 135 Gy s−1 (potentially higher) at our double-scattering beamline, increased the efficiency and field size, and enabled SOBP treatments by incorporating an optimized ridge filter. Based on our simulations we provide parametric suggestions when commissioning a new proton DS beamline. This enhanced FLASH beamline for SOBP irradiations with higher dose rates and larger field sizes will enable a wider variety of experimentation in future studies.

Surface Vertical Multi-Emission Laser with Distributed Bragg Reflector Feedback from CsPbI3 Quantum Dots.

Quantum dots (QDs) laser has become an important way to solve micro-application problems in many fields. However, single wavelength distributed Bragg reflector (DBR) has many limitations in practical applications, such as signal transmission. How to realize multiwavelength DBR lasing output simply is a challenge. To achieve a stable multi-wavelength quantum dots laser in the near-infrared region, the perovskite CsPbI3 QDs laser with DBR structure is developed in this paper. A tetragonal crystal structure with complete bonding information and no defect is explained by X-ray diffractions (XRD) and Raman spectrum. The cross-section morphology of the DBR laser and the surface morphology of QDs is measured by scanning electron microscope (SEM) and transmission electron microscope (TEM), respectively. An elliptical light propagation field and a double wavelength laser radiation are obtained from the finite-difference time-domain (FDTD) simulation. The output of the three wavelength lasers at 770 nm, 823 nm, and 873 nm is measured. The emission time of a DBR laser is about 2 h, and the average fluorescence quantum yield is 60%. The cavity length selection and energy level model are put in place to clearly see the working mechanism. All the results suggest that an effective and stable CsPbI3 quantum dots DBR laser is realized.

Absence of Tissue-Sparing Effects in Partial Proton FLASH Irradiation in Murine Intestine.

Ultra-high dose rate irradiation has been reported to protect normal tissues more than conventional dose rate irradiation. This tissue sparing has been termed the FLASH effect. We investigated the FLASH effect of proton irradiation on the intestine as well as the hypothesis that lymphocyte depletion is a cause of the FLASH effect. A 16 × 12 mm2 elliptical field with a dose rate of ~120 Gy/s was provided by a 228 MeV proton pencil beam. Partial abdominal irradiation was delivered to C57BL/6j and immunodeficient Rag1-/-/C57 mice. Proliferating crypt cells were counted at 2 days post exposure, and the thickness of the muscularis externa was measured at 280 days following irradiation. FLASH irradiation did not reduce the morbidity or mortality of conventional irradiation in either strain of mice; in fact, a tendency for worse survival in FLASH-irradiated mice was observed. There were no significant differences in lymphocyte numbers between FLASH and conventional-dose-rate mice. A similar number of proliferating crypt cells and a similar thickness of the muscularis externa following FLASH and conventional dose rate irradiation were observed. Partial abdominal FLASH proton irradiation at 120 Gy/s did not spare normal intestinal tissue, and no difference in lymphocyte depletion was observed. This study suggests that the effect of FLASH irradiation may depend on multiple factors, and in some cases dose rates of over 100 Gy/s do not induce a FLASH effect and can even result in worse outcomes.

Technical safety of buildings around polish quarries against harmful seismic vibrations caused by rock blasting

This paper presents the results of measurements of the elliptical distribution of seismic vibrations generated during rock blasting.The technical safety of a building in the area of seismic vibrations is determined by the vibration velocity that does not exceed the line B included in zone II of the scale of dynamic influences [SWD]. The hypothesis proved in the paper is that for both elliptical and circular distributions of the vibration velocity in rock mining with blasting material [BM] there is a directionality of the horizontal radial component Vx and the tangential component Vy of the vibration velocity.The magnitude of the components Vx and Vy of the vibration velocity at the same distance from the vibration source depends on the directional angle "α" between the line of the blast holes and the line connecting the centre of the surface of the rock block being mined with [BM] and the place of measurement. The elliptical shapes of the graphs Vx and Vy obtained during the mining of the BM of the basalt deposit, which depend on the value of the directional angle, were compared with the shape of the circular velocity graphs Vx and Vy. New correlations are given that take into account the directional angle when calculating the maximum vibration velocity values needed to determine the damage caused to a bulding by the SWD.A dynamic impact scale [SWD] for the assessment of building damage as the vibration velocity acting on the building increases is given and discussed. Vibration velocity diagrams measured during the excavation of BM rock are presented for circular distributions in accordance with theoretical predictions. A vibration velocity diagram for an elliptical distribution, inconsistent with a circular distribution, measured during the excavation of BM rock is presented. It is shown that the directionality of the horizontal radial and tangential components of vibration velocity exists for both circular and elliptical distribution of vibration velocity in rock excavation with BM. In the conclusions, for the elliptical velocity field of the vibrations, the conditions to be observed in order to be able to direct the smallest vibrations towards the built up area are given.

Proton FLASH effects on mouse skin at different oxygen tensions

Objective. Irradiation at FLASH dose rates (>40 Gy s−1) has received great attention due to its reported normal tissue sparing effect. The FLASH effect was originally observed in electron irradiations but has since been shown to also occur with both photon and proton beams. Several mechanisms have been proposed to explain the tissue sparing at high dose rates, including effects involving oxygen, such as depletion of oxygen within the irradiated cells. In this study, we investigated the protective role of FLASH proton irradiation on the skin when varying the oxygen concentration. Approach. Our double scattering proton system provided a 1.2 × 1.6 cm2 elliptical field at a dose rate of ∼130 Gy s−1. The conventional dose rate was ∼0.4 Gy s−1. The legs of the FVB/N mice were marked with two tattooed dots and fixed in a holder for exposure. To alter the skin oxygen concentration, the mice were breathing pure oxygen or had their legs tied to restrict blood flow. The distance between the two dots was measured to analyze skin contraction over time. Main results. FLASH irradiation mitigated skin contraction by 15% compared to conventional dose rate irradiation. The epidermis thickness and collagen deposition at 75 d following 25 to 30 Gy exposure suggested a long-term protective function in the skin from FLASH irradiation. Providing the mice with oxygen or reducing the skin oxygen concentration removed the dose-rate-dependent difference in response. Significance. FLASH proton irradiation decreased skin contraction, epidermis thickness and collagen deposition compared to standard dose rate irradiations. The observed oxygen-dependence of the FLASH effect is consistent with, but not conclusive of, fast oxygen depletion during the exposure.

Obstacle Avoidance Motion Using Elliptical Potential Field for Autonomous Robot

Obstacle Avoidance Motion Using Elliptical Potential Field for Autonomous Robot

Analysis of Coupling Efficiency in Optic Gyroscope Transceiver Module With Elliptical Core Fiber

Improving the coupling efficiency of the optical transceiver module in fiber optic gyroscopes (FOGs) benefits both the working efficiency of the module and the signal-to-noise ratio of the FOG system. In this work, a single-mode fiber (SMF) with an elliptical mode field distribution is proposed as the coupling fiber for the FOG transceiver module. The coupling efficiency of the transceiver module using fibers with different mode field distributions at the endface is analyzed. Two structure schemes of the transceiver module are compared: one focuses the beam directly onto the endface of the fiber, and the other collimates the beam and then converge it. The optimal coupling efficiency can reach above 91.5% when the horizontal and vertical mode field radii of the fiber endface are approximately 4.05 μm and 3.37 μm respectively. The influence of the axial and angular alignment errors of the pigtail on the coupling efficiency is also investigated. The maximum tolerance of the axial alignment reaches approximately ±40.10 μm and ±30.08 μm for the two structure schemes. The maximum tolerance of the angular alignment reaches approximately ±4.4° and ±5.2° in the horizontal direction, and approximately ±3.5° and ±3.6° in the vertical direction, respectively. These tolerances are favorable for practical applications.

USV compliant obstacle avoidance based on dynamic two ship domains

Aiming at the problem that unmanned surface vehicle (USV) is easy to collide with each other in dynamic environment, a flexible obstacle avoidance path planning algorithm based on dynamic two ship domains is proposed. Firstly, a dynamic two ship collision risk model based on the information of encounter vessels is established, and the type of rendezvous situation is determined on the basis of the model. Secondly, according to different rendezvous situation types, the COLREGs rules are analyzed to select the avoidance action, and a virtual circular repulsion potential field is designed for the avoidance action to guide the USV to avoid obstacles flexibly. Meanwhile, the velocity elliptical repulsion potential field is constructed for emergency avoidance under the close dangerous emergency state. Finally, simulation examples of different traffic scenarios are given to verify the effectiveness and practicability of the scheme.

Angle-tuned coils: attractive building blocks for TMS with improved depth-spread performance

Objective. A novel angle-tuned ring coil is proposed for improving the depth-spread performance of transcranial magnetic stimulation (TMS) coils and serve as the building blocks for high-performance composite coils and multisite TMS systems. Approach. Improving depth-spread performance by reducing field divergence through creating a more elliptical emitted field distribution from the coil. To accomplish that, instead of enriching the Fourier components along the planarized (x-y) directions, which requires different arrays to occupy large brain surface areas, we worked along the radial (z) direction by using tilted coil angles and stacking coil numbers to reduce the divergence of the emitted near field without occupying large head surface areas. The emitted electric field distributions were theoretically simulated in spherical and real human head models to analyze the depth-spread performance of proposed coils and compare with existing figure-8 coils. The results were then experimentally validated with field probes and in-vivo animal tests. Main results. The proposed ‘angle-tuning’ concept improves the depth-spread performance of individual coils with a significantly smaller footprint than existing and proposed coils. For composite structures, using the proposed coils as basic building blocks simplifies the design and manufacturing process and helps accomplish a leading depth-spread performance. In addition, the footprint of the proposed system is intrinsically small, making them suitable for multisite stimulations of inter and intra-hemispheric brain regions with an improved spread and less electric field divergence. Significance. Few brain functions are operated by isolated single brain regions but rather by coordinated networks involving multiple brain regions. Simultaneous or sequential multisite stimulations may provide tools for mechanistic studies of brain functions and the treatment of neuropsychiatric disorders. The proposed AT coil goes beyond the traditional depth-spread tradeoff rule of TMS coils, which provides the possibility of building new composite structures and new multisite TMS tools.

Utilising angle-dependent critical current data in the electromagnetic modelling of HTS coils

A detailed methodology is presented for modelling the electromagnetic characteristics of HTS coils using angle-dependent critical current data obtained from experimental measurements of real wire samples. The results of such an analysis are contrasted with those obtained using more prevalent approaches such as a global minimum critical current method or an elliptical field magnitude-dependent functional approximation. Several interesting design consequences of significance to real-world devices that emerge only when the full anisotropy of real wires is taken into account are outlined and discussed. These include the beneficial impact on various performance metrics of the adoption of mixed conductor windings, the importance of coil orientation in optimising device performance, and the potential opportunity to derive a specific design benefit from the targeted use of conductors possessing inclined planarity.

Third-order harmonic generation in a bi-chromatic elliptical laser field.

The low-order harmonic generation induced by a strong laser field produces a bright, ultrashort, supercontinuum radiation ranging from the terahertz to ultraviolet band. By controlling the phase-delay and ellipticity of the bi-chromatic laser fields, the third harmonic generation is experimentally and theoretically investigated for elucidating the mechanism of the low-order harmonics. The third harmonic generation is found to be strongly suppressed in the counter-rotating bi-chromatic laser field due to the selection rule for harmonic emissions. The continuum-continuum transition in the strong field approximation is extended to explain the third harmonic generation as a function of the phase delay and ellipticity of the bi-chromatic laser fields. Compared with the semi-classical photocurrent model, the continuum-continuum transition on the basis of quantum-mechanical treatment achieves better agreement with the experimental observations. Our work indicates that the overlapping in continuum states via different quantum paths of a single electron plays a role in low-order harmonics generation under elliptical bi-chromatic laser fields.

Using Camshift and Kalman Algorithm to Trajectory Characteristic Matching of Basketball Players

Because of its unique charm, sports video is widely welcomed by the public in today’s society. Therefore, the analysis and research of sports game video data have high practical significance and commercial value. Taking a basketball game video as an example, this paper studies the tracking feature matching of basketball players’ detection, recognition, and prediction in the game video. This paper is divided into four parts to improve the application of the interactive multimodel algorithm to track characteristic matching: moving object detection, recognition, basketball track characteristic matching, and player track characteristic matching. The main work and research results of each part are as follows: firstly, the improved K-means clustering algorithm is used to segment the golf field area; then, HSV is combined with the RGB Fujian value method to eliminate the field area; at last, straight field lines were extracted by Hough transform, and elliptical field lines were extracted by curve fitting, and the field lines were eliminated to realize the detection of moving objects. Seven normalized Hu invariant moments are used as the target features to realize the recognition of moving targets. By obtaining the feature distance between the sample and the template, the category of the sample is judged, which has a good robustness. The Kalman filter is used to match the characteristics of the basketball trajectory. Aiming at the occlusion of basketball, the least square method was used to fit the basketball trajectory, and the basketball position was predicted at the occlusion moment, which realized the occlusion trajectory matching. The matching of players’ track characteristics is realized by the CamShift algorithm based on the color model, which makes full use of players’ color information and realizes real-time performance. In order to solve the problem of occlusion between players in the track feature matching, CamShift and Kalman algorithms were used to determine the occlusion factor through the search window and then weighted Kalman and CamShift according to the occlusion degree to get the track feature matching result. The experimental results show that the detection time is greatly shortened, the memory space occupied is small, and the effect is very ideal.

An anisotropic Voronoi algorithm for generating polycrystalline microstructures with preferred growth directions

In this paper, a novel anisotropic Voronoi algorithm is presented, along with its implementation and two application cases. In contrast to standard Voronoi tessellations, the proposed algorithm takes into account preferred growth directions, aspect ratios and areas of individual grains. Therefore, an elliptical growth field, which is defined on a per grain basis, is adopted which specifies the time a single grain seed point needs to grow to a specific point in the domain of interest. Grains can be extracted in a grain-conforming or non-grain-conforming manner. The latter case is applicable to simulations in which a predetermined mesh is used, e.g. voxel-mesh based simulations. The extraction can then be done in a straightforward manner. For the former case, a more elaborate extraction algorithm is presented. Finally, the characteristics of the resulting microstructural geometries of two application cases (wire + arc additively manufactured and cast metal microstructure) are studied. A pronounced correspondence with the experimental grain morphology is obtained. This algorithm is highly versatile for generating polycrystalline (metal) microstructures, especially since it closely mimics the underlying solidification process. However, it is more generally applicable to generate an anisotropic tessellation with spatially varying preferential growth directions.

High harmonic generation in two-color elliptical laser fields of different helicity

This paper presents the results from the generation of elliptical high harmonics in a process of two-color elliptical laser field interaction with a single atom. Numerical simulations are performed for different values of ellipticities of the two-color driving laser field (the fundamental and the second harmonics of the Ti:Sapphire laser), together with their relative helicity. The dependency of the intensity and ellipticity of harmonics as functions of the ellipticity of the driving field components and their relative helicity is discussed. The presence of the sequence of two strong and one weak harmonics in the generated spectra in the case of a counter rotating bicircular laser field is demonstrated in this paper. The origin of weak harmonics generation is also discussed.